Gas‐Liquid Mass Transfer in Fibrous Bed Reactor with Counter‐Current Liquid Recycle

In this work, the gas‐liquid mass transfer in a lab‐scale fibrous bed reactor with liquid recycle was studied. The volumetric gas‐liquid mass transfer coefficient, k_La, is determined over a range of the superficial liquid velocity (0.0042–0.0126 m.s^–1), gas velocity (0.006–0.021 m.s^–1), surface tension (35–72 mN/m), and viscosity (1–6 mPa.s). Increasing fluid velocities and viscosity, and decreasing interfacial tension, the volumetric oxygen transfer coefficient increased. In contrast to the case of co‐current flow, the effect of gas superficial velocity was found to be more significant than the liquid superficial velocity. This behavior is explained by variation of the coalescing gas fraction and the reduction in bubble size. A correlation for k_La is proposed. The predicted values deviate within ± 15 % from the experimental values, thus, implying that the equation can be used to predict gas‐liquid mass transfer rates in fibrous bed recycle bioreactors.     

Oxygen mass transfer coefficient in bubble column slurry reactor with ultrafine suspended particles and neural network prediction

The gas–liquid volumetric mass transfer coefficient was determined by the dynamic oxygen absorption technique using a polarographic dissolved oxygen probe and the gas–liquid interfacial area was measured using dual‐tip conductivity probes in a bubble column slurry reactor at ambient temperature and normal pressure. The solid particles used were ultrafine hollow glass microspheres with a mean diameter of 8.624 µm. The effects of various axial locations (height–diameter ratio = 1–12), superficial gas velocity (u_G = 0.011–0.085 m/s) and solid concentration (ε_S = 0–30 wt.%) on the gas–liquid volumetric mass transfer coefficient k_La_L and liquid‐side mass transfer coefficient k_L were discussed in detail in the range of operating variables investigated. Empirical correlations by dimensional analysis were obtained and feed‐forward back propagation neural network models were employed to predict the gas–liquid volumetric mass transfer coefficient and liquid‐side mass transfer coefficient for an air–water–hollow glass microspheres system in a commercial‐scale bubble column slurry reactor. © 2012 Canadian Society for Chemical Engineering     

Liquid Holdup in a Pilot‐Scale Turbulent Contact Absorber – An Experimental and Comparative Study

Liquid holdup in a turbulent contact absorber was determined experimentally. Experiments were performed in a 44.7 cm diameter Perspex column. Hollow spherical high‐density polyethylene balls were used as packing. The effect of liquid and gas velocities, static bed height, diameter and density of packing on liquid holdup was investigated for the range of gas velocities greater than minimum fluidization velocities. Also, the effect of gas and liquid distributors on liquid holdup was studied. Correlations for liquid holdup were developed and compared with those in the literature. It was observed that liquid holdup increased with the increase in liquid velocity, packing density, and the decrease in static bed height. Liquid holdup also increased with gas velocity when the gas distributor section was included, while no effect was observed for the bed. Lack of information on the contribution of liquid and gas distributors seems to be the logical explanation for the wide variation in data reported in the literature.     

FILTERS AND FILTRATION HANDBOOK 4th Edition (1997) By T. Christopher Dickenson Publisher: Elsevier Advanced Technology The Boulevard,Langford Lane,Kidlington, Oxford OX5 1GB,U.K.

Abstract

Revolving air flow was generated by oblique holes on air distribution board in a fluidized bed dryer. Such a revolving air flow shows a large scale velocity fluctuation in radial as well as tangential directions. This turbulent flow of air can fluidize the inert particles with superior performance than vibrated fluidized bed. The revolving fluidized bed is simpler in fabrication and easier in operation. For two types of inert particles tested, 4 mm glass beads and 4 mm × 5 mm Teflon cylindrical extrudates, the volumetric heat transfer coefficients were found to increase with the liquid feed flowrate and air flow velocity but decrease with the air inlet temperature, height of static bed, and liquid concentration. The revolving fluidized bed gives an increase of volumetric heat transfer coefficient by 1 kW/m³ K, and represents a 15–25% enhancement from ordinary fluidized bed operated at a bed height of 60 mm, bed diameter of 140 mm, superficial air flow velocity of 3.5 m/s, liquid feed (Soya milk) flowrate of 20 mL/min at a concentration of 6.7%, and a temperature ranges of 80–140°C using Teflon extrudates as inert particles.     

Experimental Study of Oxygen Mass Transfer Coefficient in Bubble Column with High Temperature and High Pressure

The volumetric gas‐liquid mass transfer coefficient, k_Lα, for oxygen was studied by using the dynamic method in slurry bubble column reactors with high temperature and high pressure. The effects of temperature, pressure, superficial gas velocity and solids concentration on the mass transfer coefficient are systemically discussed. Experimental results show that the gas‐liquid mass transfer coefficient increases with the increase in pressure, temperature, and superficial gas velocity, and decreases with the increase in solids concentration. Moreover, k_Lα values in a large bubble column are slightly higher than those in a small one at certain operating conditions. According to the analysis of experimental data, an empirical correlation is obtained to calculate the values of the oxygen volumetric mass transfer coefficient for a water‐quartz sand system in two bubble columns with different diameter at high temperature and high pressure.     

Gas Holdup and Volumetric Mass Transfer Coefficient in a Slurry Bubble Column

The gas holdup, ?, and volumetric mass transfer coefficient, k_La, were measured in a 0.051 m diameter glass column with ethanol as the liquid phase and cobalt catalyst as the solid phase in concentrations of 1.0 and 3.8 vol.‐%. The superficial gas velocity U was varied in the range from 0 to 0.11 m/s, spanning both the homogeneous and heterogeneous flow regimes. Experimental results show that increasing catalyst concentration decreases the gas holdup to a significant extent. The volumetric mass transfer coefficient, k_La, closely follows the trend in gas holdup. Above a superficial gas velocity of 0.04 m/s the value of k_La/? was found to be practically independent of slurry concentration and the gas velocity U; the value of this parameter is found to be about 0.45 s^–1. Our studies provide a simple method for the estimation of k_La in industrial‐size bubble column slurry reactors.     

Hydrodynamics,Mass Transfer and Gas Scrubbing in a Co‐current Droplet Column Operating at High Gas Velocities

The main objective of this work was to propose a new process for household fume incineration treatment: the droplet column. A feature of this upward gas‐liquid reactor which makes it original, is to use high superficial gas velocities (13 m s^–1) which allow acid gas scrubbing at low energy costs. Tests were conducted to characterize the hydrodynamics, mass transfer performances, and acid gas scrubbing under various conditions of superficial gas velocity (from 10.0 to 12.0 m s^–1) and superficial liquid velocity (from 9.4·10^–3 to 18.9·10^–3 m s^–1). The following parameters characterized the hydrodynamics: pressure drops, liquid hold‐ups, and liquid residence time distribution were identified and investigated with respect to flow conditions. To characterize mass transfer in the droplet column, three parameters were determined: the gas‐liquid interfacial area (a), the liquid‐phase volumetric mass transfer coefficient (k_La) and the gas‐phase volumetric mass transfer coefficient (k_Ga). Gas absorption with chemical reaction methods were applied to evaluate a and k_Ga, while a physical absorption method was used to estimate k_La. The influence of the gas and liquid velocities on a, k_La, and k_Ga were investigated. Furthermore, tests were conducted to examine the utility of the droplet column for the acid gas scrubbing, of gases like hydrogen chloride (HCl) and sulfur dioxide (SO₂). This is a process of high efficiency and the amount of pollutants in the cleaned air is always much lower than the regulatory European standards imposed on household waste incinerators.     

Multiphase hydrodynamics and distribution characteristics in a monolith bed measured by optical fiber probe

The optical fiber probe has been for the first time applied to investigate the hydrodynamics and gas‐phase distribution at high gas/liquid ratios in a two‐phase flow monolith bed with 0.048 m diameter and 400 cpsi. Local hydrodynamic parameters including gas holdup, bubble frequency, bubble velocity, and bubble length in single channels were measured by 16 inserted single‐point optical fiber probes within the bed under a nozzle as the liquid distributor. The following findings are reported. (1) The optical fiber probe can be used as an efficient and convenient technique for measuring local hydrodynamic parameters inside the channels of a monolith bed; (2) within the range of high gas/liquid ratios under which experiments were conducted, churn flow regime occurred. In this regime, the monolith bed radial distribution of gas holdup, bubble frequency, bubble velocity, and bubble length is nonuniform in nature. © 2013 American Institute of Chemical Engineers AIChE J 60: 740–748, 2014     

EFFECT OF DISTRIBUTOR ON BUBBLE SIZE IN A CYLINDRICAL FLUIDIZED BED AT AN ELEVATED TEMPERATURE†

The effects of temperature and distributor on bubble diameter were investigated using a cylindrical fluidized bed of 147 mm in diameter. Three perforated distributors having different holes in diameter and the same ratio of holes to bed area were used. Eruption diameters of bubbles were measured using a high speed video-camera system under the following conditions: bed temperature = 300 and 600 K, bed particles = spherical glass beads of 272 μm in average size, excess gas velocity = 1-4 cm/s, and static bed height equals; 10-42 cm. The bubble diameter at 600 K was larger than that at 300 K. The difference became smaller with increasing the static bed height and with increasing the excess gas velocity. The distributor with larger holes gave larger bubbles. The effect of hole diameter of the distributor on the bubble diameter became insignificant with increasing the static bed height and with increasing the excess gas velocity.     

Statistical analysis of effects of experimental variables on mass transfer coefficient in a novel hybrid bubble column using Box–Behnken design

Statistical analysis of effects of experimental variables on volumetric mass transfer coefficient in a novel hybrid rotating and reciprocating perforated plate bubble column is studied. The novel bubble column is designed indigenously using bevel gear arrangement. Agitation level, superficial gas velocity, superficial liquid velocity, perforation diameter and plate spacing are the experimental variables. Air–sodium sulphite solution system is used in this investigation. The Box–Behnken design in response surface methodology is employed for statistical analysis. The relationship between experimental variables and the desired response of volumetric mass transfer coefficient is established for this novel hybrid column. The linear, quadratic and interactive effects of experimental variables are found to be significant on the desired response of volumetric mass transfer coefficient. Results show that the data adequately fit into the second‐order polynomial model. An F‐test and P‐value show the significance of parameters on volumetric mass transfer coefficient. © 2012 Canadian Society for Chemical Engineering     

Liquid hold-up and minimum fluidization velocity in a turbulent contactor

Transient-response experiments have been performed in conjunction with bed expansion measurements to determine liquid hold-ups and minimum fluidization velocities in a 12-in. turbulent-bed gas-liquid contactor. The amount of liquid hold-up was found to be independent of gas velocity, but dependent upon both liquid rate and packing diameter in the same manner as reported for conventional fixed-bed absorbers. The data on minimum fluidization velocity, G_mf, which was interpreted in the present study as the maximum gas mass velocity at which the bed maintained its static height, showed a considerable variation with packing diameter, d_p and liquid flow rate, L. A correlation of G_mf with d_p and L was presented.     

HYDRODYNAMICS, MIXING AND MASS TRANSFER IN A LARGE DIAMETER JET BUBBLE COLUMN

Experimental measurements for the axial and radial variations in gas holdup, axial and radial dispersion coefficients, volumetric gas-liquid mass transfer coefficient and liquid phase circulation velocity in a cone of a large diameter (122 cm) jet bubble column are presented. Two diameters of the inlet nozzle, namely 10.16 cm and 15.24 cm, three superficial gas velocities (based on cylinder diameter), 3 cm/sec, 6 cm/sec and 8 cm/sec and two superficial liquid velocities, 0.3 cm/sec and 0.6 cm/sec, are examined. The experimental data are obtained for two different bed heights.

The experimental data showed significant axial and radial variations in the gas holdup. The volumetric average gas holdup was higher at higher gas velocity and larger nozzle diameter and somewhat higher at lower liquid velocity. The axial dispersion was high while the radial dispersion was low. The volumetric gas-liquid mass transfer coefficient was larger at higher gas velocity and larger nozzle diameter. The liquid recirculation begins only at the upper end of the cone. In general, experimental data indicate that a jet bubble column provides a high degree of mixing and transport rates.     

EFFECT OF STATIC LIQUID HEIGHT ON GAS-LIQUID MASS TRANSFER IN A DRAFT-TUBE BUBBLE COLUMN AND THREE-PHASE FLUIDIZED BED

Experiments are performed under batch-liquid operating conditions to investigate the effect of static liquid height on the gas-liquid mass transfer coefficient (K_La) in a draft-tube bubble column (DTBC) and a draft-tube three-phase fluidized bed (DTFB). In addition, the effects of column diameter, gas-distributor, and draft-tube diameter are studied. The results indicate that for a given system with a porous plate gas-distributor at low superficial gas velocities (<70 m/hr), increasing static liquid height decreases K_La. At high gas velocities, K_La is independent of the static liquid height. For systems with a perforated gas-distributor, there is no effect of static liquid height on K_La. The formation of small dispersed bubbles at low gas velocities in the porous plate distributor system accounts for the considerably high K_La values and the observed effect of liquid height. On the other hand, the formation of large spherical-cap bubbles and the bubble coalescence at high gas velocities reduce the performance of the porous plate distributor system to that of the perforated one.     

三相下喷式环流反应器的传质性能

在三相非牛顿型流体体系中，对下喷式环流反应器传质特性进行了实验研究。讨论了表观气速、能量耗散速率、导流筒直径与反应器直径比、喷嘴直径、导流筒下端距反应器底部的距离、固体装填量、羧甲基纤维素钠（ＣＭＣ）溶液浓度及其流变特性对它的影响。实验结果表明，容积传质系数随表观气速和能量耗散速率的增加有所增加，在实验条件下，发现最优的导流筒直径与反应器直径比在０．４～０．４５这一范围、固体装填量大约为３％（体积百分比）、导流筒下端距反应器底部的距离为０．０８ｍ左右。同时提出了容积传质系数的经验关联式。     

Influence of high density particles in reduction of axial dispersion in liquid fluidized bed with residence time distribution curve studies

iquid phase RTD curves were investigated in classical fixed and fluidized bed regimes with high density particles. The effect of liquid velocity was studied on bed hydrodynamics. Using an impulse tracer injection technique in a column of 5 cm inner diameter and 1.2 m height, liquid RTD, mean residence time (MRT), axial dispersion coefficient (ADC) and vessel dispersion number (N _D ) were determined. ADC increases with liquid superficial velocity. It varied from 4.63 to 20.7 cm²/s for the particle Reynolds number of 43 to 279, respectively. The experimental results show that the hight density particles cause less ADC than the low density particles at an identical Reynolds number.     

Bubble dynamics in a 3‐D gas–solid fluidized bed using ultrafast electron beam X‐ray tomography and two‐fluid model

Bubble characteristics in a three‐dimension gas‐fluidized bed (FB) have been measured using noninvasive ultrafast electron beam X‐ray tomography. The measurements are compared with predictions by a two‐fluid model (TFM) based on kinetic theory of granular flow. The effect of bed material (glass, alumina, and low linear density polyethylene (LLDPE), d_p ～1 mm), inlet gas velocity, and initial particle bed height on the bubble behavior is investigated in a cylindrical column of 0.1‐m diameter. The bubble rise velocity is determined by cross correlation of images from dual horizontal planes. The bubble characteristics depend highly upon the particle collisional properties. The bubble sizes obtained from experiments and simulations show good agreement. The LLDPE particles show high gas hold‐up and higher bubble rise velocity than predicted on basis of literature correlations. The bed expansion is relatively high for LLDPE particles. The X‐ray tomography and TFM results provide in‐depth understanding of bubble behavior in FBs containing different granular material types. © 2014 American Institute of Chemical Engineers AIChE J, 60: 1632–1644, 2014     

Gas‐Liquid Mass Transfer in a Slurry Bubble Column at High Slurry Concentrations and High Gas Velocities

The volumetric mass transfer coefficient k_La in a 0.1 m‐diameter bubble column was studied for an air‐slurry system. A C₉‐C₁₁ n‐paraffin oil was employed as the liquid phase with fine alumina catalyst carrier particles used as the solid phase. The n‐paraffin oil had properties similar to those of the liquid phase in a commercial Fischer‐Tropsch reactor under reaction conditions. The superficial gas velocity U_G was varied in the range of 0.01 to 0.8 m/s, spanning both the homogeneous and heterogeneous flow regimes. The slurry concentration ?_S ranged from 0 to 0.5. The experimental results obtained show that the gas hold‐up ?_G decreases with an increase in slurry concentration, with this decrease being most significant when ?_S < 0.2. k_La/?_G was found to be practically independent of the superficial gas velocity when U_G > 0.1 m/s is taking on values predominantly between 0.4 and 0.6 s^–1 when ?_S = 0.1 to 0.4, and 0.29 s^–1, when ?_S = 0.5. This study provides a practical means for estimating the volumetric mass transfer coefficient k_La in an industrial‐size bubble column slurry reactor, with a particular focus on the Fischer‐Tropsch process as well as high gas velocities and high slurry concentrations.     

气液固三相循环流化床气液传质行为

<正>气液固三相流化床反应器在石油化工、湿法冶金、环境工程和煤的液化等工业领域得到了广泛应用,其基础研究也取得了很大进展.但是,传统三相床主要应用于低液速(U_L<     

Experimental Study on Bubble Rising and Descending Velocity Distribution in a Slurry Bubble Column Reactor

To determine bubble rising and descending velocity simultaneously, a BVW‐2 four‐channel conductivity probe bubble parameters apparatus and its analysis are used in gas‐liquid and gas‐liquid‐solid bubble columns. The column is 100 mm in internal diameter and 1500 mm in height. The solid particles used are glass beads with an average diameter of 17.82 μm, representing typical particle size for catalytic slurry reactors. The effects of superficial gas velocity (1.0 cm/s ≤ U_g ≤ 6.4 cm/s), solid holdup (0 % ≤ ?_s ≤ 30 %), and radial location (r/R = 0, 0.4, and 0.7) on bubble velocity distributions are determined. It is found that increasing U_g can increase the velocity of bubbles but do not exert much influence on bubble velocity distribution. Solid holdup mainly affects the distribution of bubble velocity while the radial direction affects bubble velocity distribution only slightly. The ratio of descending bubbles to rising bubbles increases from the bubble column center to the wall. It can be proved experimentally that large bubbles do not always rise faster than small bubbles at higher U_g (for example 6.4 cm/s).