A speed control method for a PM motor using a speed observer and a low‐resolution encoder

This paper proposes a new speed control method for a PM motor using a low‐resolution encoder and a speed observer. The servo system should be economical and simple. For this purpose, this paper realizes the high‐performance speed control system using a low‐resolution encoder, whose performance is nearly equal to the performance of speed servo system using a conventional optical encoder. The speed observer uses the information of motor current and motor voltage. The rotor position is calculated by the estimated value of speed observer. This observer has the influence of electrical parameter variation. This paper proposes the correction algorithm of both the voltage error of PWM inverter and the electrical parameter variation. The experimental results and numerical simulation results point out that the proposed speed control system has the desired speed response with respect to parameter variations and load torque perturbation. © 2003 Wiley Periodicals, Inc. Electr Eng Jpn, 143(1): 66–75, 2003; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10121     

Sensorless vector control of induction motor stabilized in the whole region with speed and stator resistance identification based on augmented error

This paper proposes new identification laws of an adaptive flux observer for speed sensorless vector controls. In speed sensorless vector controls of an induction motor with the adaptive observer, the speed identification system is known to be unstable in a part of the regenerating region. In addition, it is pointed out that the stator resistance variation interferes with the speed identification. Thus, it is necessary to find an adaptive scheme which can stabilize the identification system. In this paper, first, the stability on the parameter identification is discussed from the viewpoint of Popov's hyperstability. Second, identification laws for the speed and the stator resistance are proposed based on the new identification system which is derived by using the augmented error. Finally, the effectiveness of the proposed method is shown by experiments. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(1): 52–63, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20187     

An adaptive controller–observer scheme for temperature control of non‐chain reactions in batch reactors

In this paper an adaptive controller–observer temperature control scheme is developed for a class of irreversible non‐chain reactions taking place in batch reactors. The scheme is based on a nonlinear observer for the estimation of the heat released by the reaction, where the heat transfer coefficient is adaptively estimated. Tracking of the desired reactor temperature is achieved via a two‐loop control scheme, where an independent adaptive estimate of the heat transfer coefficient is used as well. Remarkably, the observer and the controller can be designed and tuned separately. The convergence of both the nonlinear observer and of the overall controller–observer scheme is analyzed by resorting to a Lyapunov‐like argument. A comparative simulation case study is developed to test the performance of the proposed scheme and compare it with other approaches already known in the literature. Copyright © 2007 John Wiley & Sons, Ltd.     

An adaptive observer for joint estimation of states and parameters in both state and output equations

An adaptive observer is a recursive algorithm for joint state–parameter estimation of parameterized state‐space systems. Previous works on globally convergent adaptive observers consider unknown parameters either in state equations or in output equations, but not in both of them. In this paper, a new adaptive observer is designed for linear time‐varying systems with unknown parameters in both state and output equations. Its global convergence for simultaneous estimation of states and parameters is formally established under appropriate assumptions. A numerical example is presented to illustrate the performance of this adaptive observer. Copyright © 2011 John Wiley & Sons, Ltd.     

Adaptive neural network output feedback stabilization of nonlinear non‐minimum phase systems

This paper presents an adaptive output feedback stabilization method based on neural networks (NNs) for nonlinear non‐minimum phase systems. The proposed controller comprises a linear, a neuro‐adaptive, and an adaptive robustifying parts. The NN is designed to approximate the matched uncertainties of the system. The inputs of the NN are the tapped delays of the system input–output signals. In addition, an appropriate reference signal is proposed to compensate the unmatched uncertainties inherent in the internal system dynamics. The adaptation laws for the NN weights and adaptive gains are obtained using Lyapunov's direct method. These adaptation laws employ a linear observer of system dynamics that is realizable. The ultimate boundedness of the error signals are analytically shown using Lyapunov's method. The effectiveness of the proposed scheme is shown by applying to a translation oscillator rotational actuator model. Copyright © 2009 John Wiley & Sons, Ltd.     

Force sensorless robust tracking servo system suppressing periodic disturbance and sudden disturbance for optical disk system

This paper proposes a new force sensorless robust tracking servo system, which detects and suppresses both the periodic disturbance and the sudden disturbance without force sensor. The proposed system estimates both the periodic disturbance and the sudden disturbance and the sudden disturbance by using a new sudden disturbance observer and the memory of tracking error. In the proposed system, the influence of sudden disturbance is suppressed by the proposed sudden disturbance observer. On the other hand, the influence of periodic disturbance is suppressed by means of ZPET feed‐forward servo system. The experimental results point out that the proposed tracking servo system has a precise tracking response against both the periodic disturbance and the sudden disturbance. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 166(1): 82–90, 2009; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20614     

Experimental verification for stability improvement of sensorless vector control system of induction motor using real‐time tuning of observer gain

This paper proposes a method for the design of the adaptive rotor flux observer gain to improve stability at low speed and in regenerating mode. The method is based on stability analysis, which utilizes a linearized model considering all systems, including each control loop. Therefore, the proposed method considers the effects of motor constants and control circuit constants. The stability analysis using the transfer function for the rotor speed considers the arrangement of poles and zeros and the steady‐state error. The rotor flux observer gain which improves the stability for each operating condition is ascertained. This paper also proposes a real‐time tuning method for the observer gain. The validity of the proposed method was confirmed by simulation using Matlab Simulink and by experiment. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 166(1): 67–81, 2009; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20715     

Adaptive observer for nonlinear fractional‐order systems

In this paper, an adaptive observer is proposed for the joint estimation of states and parameters of a fractional nonlinear system with external perturbations. The convergence of the proposed observer is derived in terms of linear matrix inequalities (LMIs) by using an indirect Lyapunov method.The proposed adaptive observer is also robust against Lipschitz additive nonlinear uncertainty. The performance of the observer is illustrated through some examples including the chaotic Lorenz and Lü's systems. Copyright © 2016 John Wiley & Sons, Ltd.     

Robust adaptive control for non‐linear systems in generalized output‐feedback canonical form

Design of global robust adaptive output‐feedback dynamic compensators for stabilization and tracking of a class of systems that are globally diffeomorphic into systems in generalized output‐feedback canonical form is investigated. This form includes as special cases the standard output‐feedback canonical form and various other forms considered previously in the literature. Output‐dependent non‐linearities are allowed to enter both additively and multiplicatively. The system is allowed to contain unknown parameters multiplying output‐dependent non‐linearities and, also, unknown non‐linearities satisfying certain bounds. Under the assumption that a constant matrix can be found to achieve a certain property, it is shown that a reduced‐order observer and a backstepping controller can be designed to achieve practical stabilization of the tracking error. If this assumption is not satisfied, it is shown that the control objective can be achieved by introducing additional dynamics in the observer. Sufficient conditions under which asymptotic tracking and stabilization can be achieved are also given. This represents the first robust adaptive output‐feedback tracking results for this class of systems. Copyright © 2003 John Wiley & Sons, Ltd.     

Stabilization control of multi‐machine power systems by adaptive power system stabilizer using frequency domain analysis

To improve electric power system transient stability, synchronous generators are generally equipped with controllers such as AVR, PSS, and GOV. Fixed parameter controllers degrade control performance, since various oscillation modes occur depending on system conditions. This paper presents an adaptive power system stabilizer (PSS) using frequency domain analysis for improving the transient stability of a multimachine system. In the proposed method, first, the frequency components of the generator swings are detected by the FFT. The conventional PSS parameters are tuned online by a fuzzy controller and frequency domain analysis. We verify the proposed adaptive PSS using frequency domain analysis, which can damp the generator swings effectively. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 142(2): 10–20, 2003; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10129     

Design of impulsive adaptive observers for improvement of persistency of excitation

The development of adaptive observer techniques for nonlinear systems in the output canonical form is proposed applying additional impulsive feedback in the observer equations. The stability of new impulsive adaptive observer is investigated. It is shown that under some conditions, the proposed impulsive feedback can improve the rate of the observer convergence or relax the requirement on persistency of excitation, which is usually introduced to ensure convergence of the parameter estimates. The proposed feasibility conditions include positivity of dwell time (boundedness of impulse frequency) and solvability of some Lyapunov‐like matrix inequalities. The results are illustrated by simulation for three examples (including a single link flexible joint robot example). Copyright © 2014 John Wiley & Sons, Ltd.     

异步电动机自适应矢量控制系统

针对经典的矢量控制系统中磁链观测器的参数偏差影响系统稳态性能和动态性能的不足,提出了把自适应控制融合到矢量控制当中的策略,设计了转子磁链自适应观测器,得出了异步电动机的转子磁链自适应观测器的算法,构成转速与磁链闭环的矢量控制系统.仿真结果表明,该系统具有一定的鲁棒性和较好的稳、动态性能.     

Running stabilization control of electric vehicle based on cornering stiffness estimation

In this paper, novel direct yaw moment control (DYC) with road condition estimation and anti‐slip control is proposed for electric vehicles. An inner‐loop observer controls the vehicle traction, and an outer‐loop observer stabilizes the yawing motion of the vehicle. An immeasurable parameter known as cornering stiffness is estimated from the detected yaw‐rate, steering angle, wheel speed and yaw moment observer output in real time. Thus, the accurate control input can be generated with the estimated parameters. The proposed adaptive control is compared with a conventional robust control method under dry and snowy terrain conditions. Experimental results show that the proposed control algorithm properly attenuates the yaw‐rate error. ©2008 Wiley Periodicals, Inc. Electr Eng Jpn, 166(4): 97–104, 2009; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20569     

Composite adaptive disturbance observer‐based control for a class of nonlinear systems with multisource disturbance

Antidisturbance control and estimation problem are introduced for a class of nonlinear system subject to multisource disturbances. The uncertain multisource disturbances consist of not only a single harmonic or constant disturbance but also another unexpected nonlinear signal described as a nonlinear function. The composite adaptive disturbance observers are constructed separately from the controller design to estimate the disturbance with partial known information. By integrating disturbance observer‐based controller with robust adaptive control, a novel type of composite adaptive disturbance observer‐based control scheme is presented for a class of nonlinear system with multisource disturbances. Simulations for a flight control system are given to demonstrate the effectiveness of the results compared with the previous schemes. Copyright © 2012 John Wiley & Sons, Ltd.     

IPMSM Position Sensorless Drives Using Robust Adaptive Observer on Stationary Reference Frame

This paper presents a novel sensorless control system for an interior permanent magnet synchronous motor (IPMSM) using adaptive observer on a stationary reference frame with its design and some experiments of position sensorless control. In sensorless control of IPMSM, adaptive observer structure and its design remain as one of the open problems. This is because the linear model on the stationary reference frame for IPMSM has not been established so far. As a result, the construction of an adaptive observer seems to be complicated owing to nonlinearity of the IPMSM model. From this viewpoint, a novel linear model of IPMSM on a stationary reference frame is first described in this paper. Second, an adaptive observer design is proposed based on γ‐positive real problem, yielding realization of both robust position estimation and robustly stable speed adaptation with respect to speed adaptation delay. Finally, some experiments with and without load torque at low and middle speed ranges are shown to demonstrate the feasibility and the effectiveness of the proposed system. Copyright © 2007 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Adaptive observer for a class of nonlinear systems with time‐varying delays

The adaptive observer design problems have been extensively studied in literature for both linear and nonlinear systems. Some researches have also been carried out on adaptive observer design for linear time‐delay systems, but there is no significant work on adaptive observer design for nonlinear time‐delay systems. In this work, the adaptive observer design problem for a class of nonlinear time‐delay systems is considered. The observer is designed for the nonlinear systems whose nonlinear functions satisfy Lipschitz condition. Like conventional adaptive observers for the systems without time delays, this observer also estimates both states and unknown parameters simultaneously. For this property, it will be very much useful for many real‐time systems where time delays cannot be avoided. The sufficient conditions for existence of the observer are derived using the linear matrix inequality approach. With the help of a numerical example, effectiveness of the proposed observer is demonstrated. Copyright © 2012 John Wiley & Sons, Ltd.     

A disturbance‐decoupled adaptive observer and its application to faulty parameters estimation of a hydraulically driven elevator

In this paper, a disturbance‐decoupled adaptive observer is designed for the joint state‐parameter estimation of a system with unknown disturbance inputs. The proposed Robust Adaptive Observer (RAO) integrates an Unknown Input Observer (UIO) to the parameter estimation process, where the unknown parameters are estimated as extended states of the system. An auxiliary input is added to the UIO in coping with the estimation errors so that the exponential stability and convergence of the observer are guaranteed. The proposed observer is applied to a hydraulically driven elevator for the faulty parameter estimation. The simulation results show the accuracy of the observer and its robustness to both disturbances and measurement noises. Copyright © 2010 John Wiley & Sons, Ltd.     

Adaptive sliding mode observer design for a class of uncertain systems

State feedback method is quite popular in control engineering field. However, some popular properties of state feedback approach cannot be used while any of the system states cannot be obtained beforehand. Therefore, this paper proposes a new observer design for a class of uncertain systems through sliding mode control theory. Based on strictly positive real concept, the stability of the equivalent error system is verified. Further, by using the generalized matrix inverse approach, the proposed switching term can drive the error states to zero, and it ensures the global reaching condition of the sliding mode of the error system. Moreover, the presented sliding mode observer is proposed to possess the invariance property to the uncertainty and/or external disturbance. Furthermore, the developed sliding mode observer is extended to release the limitation of knowing the bounds of the lumped perturbations in advance. That is, not only a new sliding mode observer but also a new adaptive sliding mode observer is proposed in this paper. Finally, three examples are illustrated to demonstrate the validity of the proposed sliding mode observer and the proposed adaptive sliding mode observer. Copyright © 2014 John Wiley & Sons, Ltd.     

Active fault‐tolerant control for switched systems with time delay

This paper focuses on the problem of active fault‐tolerant control for switched systems with time delay. By utilizing the fault diagnosis observer, an adaptive fault estimate algorithm is proposed, which can estimate the fault signal fast and exactly. Meanwhile, a delay‐dependent criterion is obtained with the purpose of reducing the conservatism of the adaptive observer design. Based on the fault estimation information, an observer‐based fault‐tolerant controller is designed to guarantee the stability of the closed‐loop system. In terms of linear matrix inequality, sufficient conditions are derived for the existence of the adaptive observer and fault‐tolerant controller. Finally, a numerical example is included to illustrate the efficiency of the proposed approach. Copyright © 2011 John Wiley & Sons, Ltd.