Interfacial properties of polycarbonate/liquid‐crystal polymer and polystyrene/high‐impact polystyrene polymer pairs under shear deformation

We developed an energy model derived from the first principle for multilayer configurations to enhance our understanding of the interfacial property between two polymers under shear deformation. We carried out specific experiments satisfying the boundary and loading conditions of the model to obtain the energy dissipation factor (β), which characterized and quantified the interfacial property. Two polymer pairs, the miscible system polystyrene (PS)/high‐impact polystyrene (HIPS) and the immiscible system polycarbonate (PC)/liquid‐crystal polymer (LCP), were investigated. As expected, β was zero for PS/HIPS, reflecting the strong interaction at the PS/HIPS interface. For PC/LCP, the value of β could be significant, and its behavior was complex; it reflected the thermal sensitivity and thermal history effect of the PC/LCP interface. A positive value of β also indicated the possibility of slip at the interface and provided an explanation for the negative deviation from the rule of mixture. This complex behavior of the interface was attributed to the changes in the phases and microstructure of LCPs and, therefore, the LCP/PC interface as thermal cycling was carried out in the melting/nematic range of LCPs. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 258–269, 2003     

Characterization of the free volume in high‐impact polystyrene/polypropylene and high‐impact polystyrene/high‐density polyethylene blends probed by positron annihilation spectroscopy

The free‐volume properties of high‐impact polystyrene (HIPS)/polypropylene (PP) and HIPS/high‐density polyethylene (HDPE) blends were investigated by means of positron annihilation lifetime spectroscopy (PALS). The measured results show that the free‐volume holes in the semicrystalline polymers, such as PP and HDPE, were not large enough to accommodate the branched chains and the end groups of the macromolecular chains in HIPS to produce favorable interactions between the semicrystalline polymers and the HIPS polymer in these blends; thus immiscible blends were formed. The weak interaction between two dissimilar polymer molecules only took place in the regions between two amorphous phases. In addition, the observed negative deviations of the longest lifetime intensity and the free‐volume fraction were attributed to the influence of the interfacial polarization during PALS measurement. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1507–1514, 2003     

Toughness and morphology of radiation‐crosslinked natural rubber modified polystyrene

γ‐Radiation vulcanized natural rubber (RVNR)/phase transfer/suspension polymerization technique was used to prepare high‐impact polystyrene (HIPS) in bead form. The high notched Izod impact resistance of HIPS based on RVNR was observed and compared with that of unmodified PS. The impact resistance of HIPS based on RVNR was further enhanced by addition of 10% of polystyrene‐block‐polyisoprene‐block‐polystyrene copolymer. A mesh structure of all crosslinked rubber particles containing polystyrene and long crazes in HIPS were observed under electron microscopy. Copyright © 2003 Society of Chemical Industry     

Compatibilization of high‐impact polystyrene/high‐density polyethylene blends by styrene/ethylene–butylene/styrene block copolymer

Compatibilization of polymer blends of high‐impact polystyrene (HIPS) and high‐density polyethylene (HDPE) blend by styrene/ethylene–butylene/styrene (SEBS) was elucidated. Polymer blends containing many ratios of HIPS and HDPE with various concentrations of SEBS were prepared. The Izod impact strength and elongation at break of the blends increased with increases in SEBS content. They increased markedly when the HDPE content was higher than 50 wt %. Tensile strength of blends increased when the SEBS concentration was not higher than 5 pphr. Whenever the SEBS loading was higher than 5 pphr, the tensile strength decreased and a greater decrease was found in blends in which the HDPE concentration was more than 50 wt %. The log additivity rule model was applied to these blends, which showed that the blends containing the HIPS‐rich phase gave higher compatibility at the higher shear rates. Surprisingly, the blends containing the HDPE‐rich phase yielded greater compatibility at the lower shear rates. Morphology observations of the blends indicated better compatibility of the blends with increasing SEBS concentration. The relaxation time (T₂) values from the pulsed NMR measurements revealed that both polymer blends became more compatible when the SEBS concentration was increased. When integrating all the investigations of compatibility compared with the mechanical properties, it is possible to conclude that SEBS promotes a certain level of compatibilization for several ratios of HIPS/HDPE blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 742–755, 2004     

Strategies to measure and optimize the migration of the interfacial modifier to the interface in immiscible polymer blends

A family of emulsification curves has been systematically prepared in order to determine the extent of interfacial modifier migration to the high density polyethylene (HDPE)/polystyrene (PS) interface. Through an examination of the evolution of the equilibrium dispersed phase size after interfacial saturation, as well as a comparison of the apparent interfacial area occupied per modifier molecule (A_app) at the different dispersed phase concentrations, it is possible to detect the onset of micelle formation and to estimate the extent of interfacial coverage. This approach has been applied to HDPE/PS blends, using a variety of triblock and diblock copolymer interfacial modifiers for that system. It is shown quantitatively that it is the affinity of the block copolymer for the matrix material that dominates migration efficacy to the interface. Asymmetrical block copolymers (30PS/70EB) show a strong tendency to form micelles when HDPE is the matrix. This effect is virtually eliminated when PS is the matrix material or when symmetrical block copolymers (50PS/50EB) are used. In these latter cases all the interfacial modifier finds its way to the interface.     

Dynamic rheological properties of high‐density polyethylene/polystyrene blends extruded in the presence of ultrasonic oscillations

The linear rheological properties of high‐density polyethylene (HDPE), polystyrene (PS), and HDPE/PS (80/20) blends were used to characterize their structural development during extrusion in the presence of ultrasonic oscillations. The master curves of the storage shear modulus (G′) and loss shear modulus (G″) at 200°C for HDPE, PS, and HDPE/PS (80/20) blends were constructed with time–temperature superposition, and their zero shear viscosity was determined from Cole–Cole plots of the out‐of‐phase viscous component of the dynamic complex viscosity (η″) versus the dynamic shear viscosity. The experimental results showed that ultrasonic oscillations during extrusion reduced G′ and G″ as well as the zero shear viscosity of HDPE and PS because of their mechanochemical degradation in the presence of ultrasonic oscillations; this was confirmed by molecular weight measurements. Ultrasonic oscillations increased the slopes of log G′ versus log G″ for HDPE and PS in the low‐frequency terminal zone because of the increase in their molecular weight distributions. The slopes of log G′ versus log G″ for HDPE/PS (80/20) blends and an emulsion model were used to characterize the ultrasonic enhancement of the compatibility of the blends. The results showed that ultrasonic oscillations could reduce the interfacial tension and enhance the compatibility of the blends, and this was consistent with our previous work. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3153–3158, 2004     

Ultrasonic improvement of the compatibility and rheological behavior of high‐density polyethylene/polystyrene blends

The effects of ultrasonic oscillations on the rheological behavior, mechanical properties, and morphology of high‐density polyethylene (HDPE)/polystyrene (PS) blends were studied. The experimental results show that the die pressure and apparent viscosity of HDPE/PS blends are remarkably reduced in the presence of ultrasonic oscillations and that mechanical properties of the blends are improved. The particle size of the dispersed phase in HDPE/PS blends becomes smaller, its distribution becomes narrower, and the interfacial interaction of the blends becomes stronger if the blends are extruded in the presence of ultrasonic oscillations. Ultraviolet spectra and Soxhlet extraction results show the formation of a polyethylene‐PS copolymer during extrusion in the presence of ultrasonic oscillations, which improves the compatibility of HDPE/PS blends. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 23–32, 2002     

Phase morphologies and mechanical properties of high‐impact polystyrene (HIPS) and polycarbonate blends compatibilized with polystyrene and polyarylate block copolymer

Phasemorphology and mechanical properties of blends of high‐impact polystyrene (HIPS) and polycarbonate (PC) blends compatibilized with a polystyrene (PS) and polyarylate (PAr) (PS–PAr) block copolymer were investigated. Over a broad range of composition from 50/50 through 30/70, HIPS/PC blends formed cocontinuous structures induced by the flow during the extrusion or injection‐molding processes. These cocontinuous phases had heterogeneity between the parallel and perpendicular directions to the flow. The micromorphology in the parallel direction to the flow consisted of stringlike phases, which were highly elongated along the flow. Their longitudinal size was long enough to be longer than 180 μm, while their lateral size was shorter than 5 μm, whereas that in the perpendicular direction to the flow showed a cocontinuous phase with regular spacing due to interconnection or blanching among the stringlike phases. The PS–PAr block copolymer was found to successfully compatibilize the HIPS/PC blends. The lateral size of the stringlike phases could be controlled both by the amount of the PS–PAr block copolymer added and by the shear rate during the extrusion or injection‐molding process without changing their longitudinal size. The HIPS/PC blend compatibilized with 3 wt % of the PS–PAr block copolymer under an average shear rate of 675 s^?1 showed a stringlike phase whose lateral size was reduced almost equal to the rubber particle size in HIPS. The tensile modulus and yield stress of the HIPS/PC blends could be explained by the addition rule of each component, while the elongation at break was almost equal to that of PC. These mechanical properties of the HIPS/PC blends can be explained by a parallel connection model independent of the HIPS and PC phases. On the other hand, the toughness factor of the HIPS/PC blends strongly depended on the lateral size of the stringlike phases and the rubber particle size in the HIPS. It was found that the size of the string phases and the rubber particle should be smaller than 1.0 μm to attain a reasonable energy absorbency by blending HIPS and PC. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2347–2360, 2001     

Deformation mechanisms and fracture toughness of polystyrene/high‐density polyethylene blends compatibilized by triblock copolymer

A dilatometric technique was used to explore the tensile deformation mechanisms of polystyrene (PS)/high‐density polyethylene (HDPE) blends compatibilized by a styrene–ethylene–butylene–styrene (SEBS) triblock copolymer. The volume change of the sample during a uniaxial tensile process was determined with two extensometers, and it provided useful information concerning the tensile deformation mechanism. A simple model was used in this study in order to obtain quantitative information on the separate contributions of several possible deformation modes to the total deformation. The results indicated that elastic deformation was the main deformation mode for PS. However, elastic deformation was the main mode of deformation prior to yielding for SEBS compatibilized PS/HDPE blends; thereafter the plastic deformations (including shear and crazing) appeared to dominate over the elastic deformation. Moreover, crazing was the main plastic deformation mode for the blend containing 20 wt % HDPE, and shear deformation became predominant when the HDPE content was further increased. Finally, the essential work concept was used to determine the fracture toughness of the typical ductile PS/HDPE/SEBS 10/80/10 blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2024–2033, 2000     

Rheological characterisation of hydroxyapatite filled polyethylene composites. Part 2 – Isothermal compressibility and wall slip

Abstract

Rheological characterisation of hydroxyapatite–high density polyethylene (HA–HDPE) composites has been performed in terms of isothermal compressibility and wall slip. Addition of HA to the polymer melt decreases the compressibility of the melt. The unfilled HDPE was found to exhibit wall slip at shear stresses as low as 0·10 MPa. The flow curves of the composites showed three distinct regions: a gradient at low shear rates; a plateau region; and a gradient at higher shear rate. An increase in rheometer pressure seems to suppress the slip in composites. The 40 vol.-% HA–HDPE composite exhibited two critical shear stresses, one corresponding to wall slip, which occurs in the lower shear rate region of the flow curve, and the other corresponding to a plateau, which is identified with the stick–slip behaviour of unfilled HDPE reported in the literature. The plateau shear stress increased with filler volume fraction and this effect is attributed to the decreased compressibility of the melt. A good correlation with a negative correlation coefficient was found to exist between compressibility and shear stress in the plateau region. The slip observed in unfilled HDPE and at low shear rates in the 40 vol.-% HA–HDPE systems has been explained in terms of a low molecular weight polymer layer formed at the melt/wall interface. The large interfacial slip observed in the plateau region is attributed to complete disentanglement of adsorbed chains from free chains at the melt/wall interface at and beyond the plateau region.     

Deformation mechanism of polystyrene toughened with sub‐micrometer monodisperse rubber particles

Core–shell polybutadiene‐graft‐polystyrene (PB‐g‐PS) rubber particles with different ratios of polybutadiene to polystyrene were prepared by emulsion polymerization through grafting styrene onto polybutadiene latex. The weight ratio of polybutadiene to polystyrene ranged from 50/50 to 90/10. These core‐shell rubber particles were then blended with polystyrene to prepare PS/PB‐g‐PS blends with a constant rubber content of 20 wt%. PB‐g‐PS particles with a lower PB/PS ratio (≤70/30) form a homogeneous dispersion in the polystyrene matrix, and the Izod notched impact strength of these blends is higher than that of commercial high‐impact polystyrene (HIPS). It is generally accepted that polystyrene can only be toughened effectively by 1–3 µm rubber particles through a toughening mechanism of multiple crazings. However, the experimental results show that polystyrene can actually be toughened by monodisperse sub‐micrometer rubber particles. Scanning electron micrographs of the fracture surface and stress‐whitening zone of blends with a PB/PS ratio of 70/30 in PB‐g‐PS copolymer reveal a novel toughening mechanism of modified polystyrene, which may be shear yielding of the matrix, promoted by cavitation. Subsequently, a compression‐induced activation method was explored to compare the PS/PB‐g‐PS blends with commercial HIPS, and the result show that the toughening mechanisms of the two samples are different. Copyright © 2006 Society of Chemical Industry     

Recycling of high density polyethylene/poly(vinyl chloride)/polystyrene ternary mixture with the aid of high energy radiation and compatibilizers

Ternary mixtures of waste plastics of high density polyethylene (HDPE), poly(vinyl chloride) (PVC), and polystyrene (PS) was recycled using a single‐screw extruder. Poly(ethylene‐co‐vinyl acetate) and poly(styrene‐b‐ethylene/butylenes‐b‐styrene) were introduced as compatibilizers for HDPE/PVC and HDPE/PS, respectively. After the polymer blends was prepared via extrusion, they were subjected to high energy irradiation. The morphology and the mechanical properties of the hybrid blends were examined. Scanning electron micrographs and transmission electron micrographs showed that both compatibilizers and irradiation improved the uniformity and dispersion of the system. The heterogeneous crosslinking generated by irradiation resulted in an optimum impact strength. High elongation at break was achieved by using compatibilizers. The improvement of tensile strength was moderate. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 12: 2756–2762, 2003     

Morphology studies of multilayered HDPE/PS systems

Films with alternating layers of high density polyethylene (HDPE) and polystyrene (PS) were prepared by layer‐multiplying coextrusion, using two HDPEs differing in molecular weight. The crystal structure of extremely thin PE layers confined between PS layers was studied by small angle X‐ray scattering (SAXS), wide angle X‐ray diffraction (WAXS), and also by atomic force microscopy (AFM) and differential scanning calorimetry (DSC) technique including MDSC. The morphology of HDPE in the systems studied is greatly affected by the presence of HDPE/PS interfaces. In the HDPE layers, the texture component was observed with lamellae with their basal planes normal to the interface and (200) crystallographic planes parallel to the interface. Thus, the polymer chains in this texture component are parallel to the interface between both polymers. The small fraction of lamellae parallel to the interface in thicker HDPE layers disappears with the thinning of the layers beyond 100 nm. AFM images show in these samples straight, long lamellae positioned edge‐on at HDPE/PS interface. The thickness and perfection of lamellae decrease with the decrease of individual HDPE layer thickness. Those thinner and less perfect lamellae are more susceptible to reorganization during heating as it is observed by MDSC. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 597–612, 2006     

Compatibilization of poly(lactic acid)/high impact polystyrene interface using copolymer poly(stylene‐ran‐methyl acrylate)

In this work, a surfactant‐free emulsion polymerization method was utilized to synthesize poly(styrene‐ran‐methyl acrylate) (PSMA) at a styrene/(methyl acrylate) mole ratio of 75/25 with the aim to compatibilize high impact polystyrene (HIPS)/poly(lactic acid) (PLA) interface. HIPS/PLA blends with different PSMA contents were prepared. Their phase morphologies, mechanical properties, and rheological and crystallization behaviors were investigated using scanning electron microscopy, tensile tests, rotational rheometry, and differential scanning calorimetry. The rheological results showed that the complex viscosity, storage moduli, and loss moduli of PLA/HIPS blends were enhanced with increasing PSMA content. A decrease in the degree of crystallinity of PLA in PLA/HIPS blends with the addition of PSMA was observed in the differential scanning calorimetry results. It was also revealed that the addition of a small amount of PSMA can effectively improve the compatibility and thus the interfacial adhesion of the PLA/HIPS blends, thereby reducing the size of the HIPS dispersion phase. When 1 wt % of PSMA was used, compared with the PLA/HIPS blends without PSMA, the tensile strength and notched Charpy impact strength of PLA/HIPS blends were improved by 95.3% and 104.8%, respectively. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45799.     

Interfacial modification of high impact polystyrene magnesium hydroxide composites effects on flame retardancy properties

High impact polystyrene (HIPS)/magnesium hydroxide (MH) composites were prepared by melt‐blending. Two kinds of interfacial modifiers were used in this research, maleinated poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS‐g‐MA) triblock copolymer and PS. The effects of the use levels of SEBS‐g‐MA on the flame retardancy of HIPS/elastomer/MH based on unmodified and PS‐modified surface were investigated by TEM, FTIR, and combustion tests (horizontal burning test and cone calorimetry). The combustion results showed that comparing composites containing unmodified MH, the flame retarding properties of composites containing PS‐modified MH were obviously improved. The increased performance can be explained that the PS covered on the surface of MH could further improve dispersion of the filler in matrix. Furthermore, there existed a critical thickness of interfacial boundary for optimum flame‐retarding properties in both ternary composites based MH and PS‐modified MH. When the interfacial boundary relative thickness is less than 0.53, the introduction of SEBS‐g‐MA can improve the dispersion degree, leading the improvement of flame retardancy properties. However, with the increase of interfacial boundary thickness, the SEBS‐g‐MA coating around MH acted as a heat and mass transfer barrier, leading to the reduction of flame retardancy. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

含易挥发组分的聚合物溶液流变行为测定

利用HAAKE流变仪的D100/300测量系统,对聚苯乙烯/苯乙烯(PS/St)、高抗冲聚苯乙烯/苯乙烯(HIPS/St)及甲基硅油/环已烷等体系的流变行为进行了测定。测得40％PS/St和50％HIPS/St的平均流变行为指数分别为0.998和0.969,可近似作为牛顿流体处理。甲基硅油则是典型的牛顿流体,并得出了其粘度的关联式。     

Morphology and flame‐retardancy properties of ternary high‐impact polystyrene/elastomer/polystyrene‐encapsulated magnesium hydroxide composites

The effects of elastomer type on the morphology, flammability, and mechanical properties of high‐impact polystyrene (HIPS)/polystyrene (PS)‐encapsulated magnesium hydroxide (MH) were investigated. The ternary composites were characterized by cone calorimetry, mechanical testing, and scanning electron microscopy. Morphology was controlled with poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) triblock copolymer or the corresponding maleinated poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS‐g‐MA). The HIPS/SEBS/PS‐encapsulated MH composites exhibited separation of the filler and elastomer, whereas the HIPS/SEBS‐g‐MA/PS‐encapsulated MH composites exhibited encapsulation of the filler by SEBS‐g‐MA. The flame‐retardant and mechanical properties of the ternary composites were strongly dependent on microstructure. The composites with an encapsulation structure showed higher flame‐retardant properties than those with a separation structure at the optimum use level of SEBS‐g‐MA. Furthermore, the composites with a separation structure showed a higher modulus and impact strength than those with an encapsulation structure. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Rheological,mechanical and morphological properties of thermoplastic vulcanizates based on high impact polystyrene and styrene‐butadiene rubber

Thermoplastic vulcanizates (TPVs) based on high impact polystyrene (HIPS)/styrene‐butadiene rubber (SBR) blends were prepared by dynamic vulcanization technique. The rheological, mechanical and morphological properties of the dynamically vulcanized blends were investigated systematically. As determined by capillary rheometer, the apparent viscosity of the blends decreases as the shear rate increases, indicating obvious pseudoplastic behavior. At low shear rate, the apparent viscosity of these blends is considerably higher than that of neat HIPS and decreases with the increase of HIPS concentration. The increase of HIPS content in the dynamically vulcanized blends contributes to the increase of tensile strength and hardness properties, while elongation at break and tensile set at break reach a maximum at 30 and 50 wt % of the HIPS content, respectively. The etched surfaces of the HIPS/SBR TPVs were investigated using field‐emission scanning electron microscopy, the morphological study reveals continuous HIPS phase and finely dispersed SBR elastomeric phase in the TPVs. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Compatibilization of polyethylene/poly(propylene)/polystyrene blends

The compatibilization of mixtures of polyolefins or of polyolefins with polystyrene using either liquid polybutadiene (l-PB)/organic peroxide or styrene-butadiene-styrene (SBS) block copolymers was investigated. Tensile impact strength was chosen as a measure of compatibility. Binary blends LDPE/high-impact polystyrene (HIPS) and LDPE/poly(propylene) (PP) as well as LDPE/HDPE/PP/HIPS blends were prepared by blending in the chamber of a Brabender Plasticorder. Composition of the blends corresponds to real commingled plastic waste. It was found that l-PB-based compatibilizer enhanced the impact strength of LDPE/HIPS blends with LDPE contents higher than 60 wt.-% only. Also SBS copolymer enhanced the impact strength of LDPE/PP blends with LDPE contents higher than 40 wt.-%. Both the compatibilizers substantially increased the toughness of LDPE/HDPE/PP/HIPS blends with composition similar to the municipal plastic waste.     

Ultraporous poly(l-lactide) scaffolds prepared with quaternary immiscible polymer blends modified by copolymer brushes at the interface

The activity of polystyrene-block-poly(l-lactide) (PS-b-PLLA) and polystyrene-block-poly(methyl methacrylate) (PS-b-PMMA) diblock copolymer brushes located at a PS/PLLA interface were employed as a route to control the final microstructure of 95% void volume, ultraporous PLLA scaffolds. The latter were initially prepared from melt-processed quaternary blends of ethylene propylene diene rubber/poly(?-caprolactone)/polystyrene/poly(l-lactide) (EPDM/PCL/PS/PLLA) 45/45/5/5%vol. modified with the diblock copolymers. The blends display a layer comprised of the PS and PLLA phases located at the interface of the co-continuous EPDM and PCL phases. When the PS-b-PLLA copolymer is added, sub-micrometric PLLA droplets are encapsulated within the PS continuous layer phase. In comparison, both the PS and PLLA phases compete for the encapsulation process when the PS-b-PMMA is used, indicating that the microstructure of the PLLA phase can be fine-tuned with an adequate choice of interfacial modifier. These effects were investigated by analyzing the microstructure of ternary high-density polyethylene (HDPE)/PS/PMMA 80/10/10%vol. blends displaying PS/PMMA shell/core composite droplets in a HDPE matrix. An inversion of the shell/core structure is observed when the PS-b-PLLA copolymer is used to compatibilize the PS/PMMA interface, whereas no such restructuring occurs with the PS-b-PMMA. These effects are explained by the activity and swelling powers of the copolymer brushes. For the EPDM/PCL/PS/PLLA quaternary systems modified with the PS-b-PMMA, the PLLA homopolymer phase significantly penetrates and swells the PMMA blocks due to their mutual high affinity, as compared to the classical like-prefers-like compatibilization approach. The swelling of the blocks will tend to bend the interface toward the PS phase in order to minimize the lateral compression of the PMMA blocks. A similar effect explains the reversal of the PS/PMMA shell/core structure in the HDPE/PS/PMMA ternary system. This level of control ultimately leads to quite significant differences in microstructures and surface textures for the PLLA scaffolds.