Solvent effects on the miscibility of poly(methyl methacrylate)/poly(bisphenol a carbonate) blends

Blends of atactic or syndiotactic poly(methyl methacrylate) (designated as aPMMA or sPMMA) and poly(bisphenol A carbonate) (PC) were prepared from solution casting. Tetrahydrofuran (THF) and chloroform were used as solvent. Experimental results indicated that the as‐cast blends from THF were quite different from the chloroform‐cast ones. After film preparation, THF‐cast blends did not show any visible phase separation. However, chloroform‐cast blends formed a phase‐separated structure. The as‐cast PC from either solvent was not completely amorphous, and had a melting point at 239–242°C, indicating a certain degree of crystallinity. In contrast, the quenched samples of aPMMA/PC blends prepared from the two solvents behaved virtually the same. They both showed aPMMA dissolves better in PC, but PC solubility in aPMMA is very little. Using sPMMA instead of aPMMA to blend with PC, different results were obtained. The quenched sPMMA/PC blends cast from THF showed only one T_g. However, immiscibility (i.e., two T_gs) was found in the same blend system when cast from chloroform. THF was believed to cause the observation of single T_g due to the following kinetic reason. sPMMA and PC were still trapped together even after THF removal in a homogeneous, but nonequilibrium state below the glass transition. Therefore, the quenched sPMMA/PC blends were not truly thermodynamically miscible. From the results of aPMMA or sPMMA with PC, increasing syndiotacticity seemed to improve the miscibility between PMMA and PC. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2842–2850, 2001     

Casting solvent effect on crystallization behavior and morphology of poly(ethylene oxide)/poly(methyl methacrylate)

Poly(ethylene oxide) (PEO)/poly(methyl methacrylate) (PMMA) blends were prepared by casting from either chloroform or benzene solvents. After casting from solvents, all samples used in this study were preheated to 100°C and held for 10 min. Then, the solvent effect on the crystallization behavior and thermodynamic properties were studied by differential scanning calorimeter (DSC). Also, the morphology of spherulite of casting film was studied by polarized optical microscope. From the DSC and polarizing optical microscopy (POM) results, it was found that PEO/PMMA was miscible in the molten state no matter which casting solvent was used. However, the crystallization of PEO in the chloroform‐cast blend was more easily suppressed than it was in the benzene‐cast blend. Relatively, the chloroform‐cast blend showed the greater melting‐point depressing of PEO crystals. Also, the spherulite of chloroform‐cast film showed a coarser birefringence. It was supposed that the chloroform‐cast blend had more homogeneous morphology. It is fair to say that polymer blends, cast from solvent, are not necessarily in equilibrium. However, the benzene‐cast blends still were not in equilibrium even after preheating at 100°C for 10 min. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1627–1636, 2000     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(vinyl acetate)

The results of the miscibility between the chemically similar polymers poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) published so far show inconsistent statements concerning miscibility. The problems may be due to differences in molecular weights, tacticity, and preparation methods of the polymers. This investigation was carried out by using either chloroform or tetrahydrofuran (THF) as solvent to prepare the blends, because to our knowledge, nobody has reported any tacticity effect of PMMA on the miscibility with PVAc. Therefore, in this article, different tactic PMMAs were used to mix with PVAc and their miscibility was studied calorimetrically. The results showed little effect of solvent and tacticity. PMMA and PVAc were determined to be almost completely immiscible because of the observation of two T_g's. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 35–39, 2004     

Casting solvent effect on crystallization behavior of poly(vinyl acetate)/poly(ethylene oxide) blends: DSC study

Poly(vinyl acetate) (PVAc)/poly(ethylene oxide) (PEO) blends were prepared by casting from either benzene or chloroform. The solvent effects on the crystallization behavior and thermodynamic properties of the blends were studied by the differential scanning calorimeter (DSC). Two grades of PEO with different molecular weights (PEO200 with M_w = 200,000 g/mol and PEO2 with M_n = 2000 g/mol) were used in this work. The thermal analysis revealed that the blends cast from either benzene or chloroform were miscible in the molten state. The crystallization of PEO in the benzene-cast blends was more easily suppressed than it was in the chloroform-cast blends. Furthermore, the benzene-cast blends showed a greater negative value of Flory-Huggins interaction parameter than those cast from chloroform in the PVAc/PEO200 poly-blend system. It was supposed that the benzene-cast blends had more homogeneous morphology. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 411–421, 1997     

Dual xanthan gum/poly(vinyl acetate) or alkyl‐functionalized poly(vinyl alcohol) films as models for advanced coatings

Double‐layer films, prepared by casting films of xanthan gum (XG), and subsequently poly(vinyl acetate) (PVAc) onto the former, are reported. The resulting XG/PVAc films provide high protection as coatings to a bleaching agent, 6‐(phthalimido)peroxyhexanoic acid, in liquid detergents, due to the combined roles of the outer PVAc layer as water‐barrier and the inner XG layer as water‐sink. PVAc films cast from either homogeneous solutions in acetone or aqueous dispersions were used; the stabilities exerted by the former were markedly superior. For comparison, poly(vinyl alcohol) (PVA) was also used as outer wall material, resulting in much lower protection due to its hydrophilicity. Functionalization (silylation or acetalyzation) of PVA films is also suggested as a means to decrease the surface hydrophilicity of the material. The dual hydrophilic–hydrophobic films presented herein serve as models for advanced coatings in (micro)encapsulation processes, owing to the straightforward study of their morphology and transport phenomena. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40870.     

Polymer compatibility III. The system poly(methyl methacrylate)–poly(vinyl acetate). Characterization studies

Blends of poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) were prepared by mixing the polymers in the melt and in the absence of a solvent. PMMA was the major constituent of the blend. The polymer blends were tested, using various methods, to determine if they are compatible as solids. Data obtained from dynamic mechanical and DSC measurements show that, when they are mixed under given Brabender mix conditions, the blends exhibit properties characteristic of polymer pairs compatible as solids. If the mix conditions are altered, a two-phase system is evidenced. Using micrographs obtained by light microscopy in phase contrast as criteria, two companion blends containing PMMA/PVAc 80/20 would be classified as incompatible as solids because of the differences in refractive index of PMMA and PVAc. The micrographs also show that, in the system that would otherwise be listed as compatible, the PVAc domains appear to be relatively uniform in size and distribution through the PMMA matrix. In its companion blend, large, irregularly shaped particles of PVAc which are poorly dispersed in the PMMA matrix are evident.     

Atom transfer radical polymerization of methyl methacrylate initiated with a macroinitiator of poly(vinyl acetate)

Well‐defined poly(vinyl acetate‐b‐methyl methacrylate) block copolymers were successfully synthesized by the atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) in p‐xylene with CuBr as a catalyst, 2,2′‐bipyridine as a ligand, and trichloromethyl‐end‐grouped poly(vinyl acetate) (PVAc–CCl₃) as a macroinitiator that was prepared via the telomerization of vinyl acetate with chloroform as a telogen. The block copolymers were characterized with gel permeation chromatography, Fourier transform infrared, and ¹H‐NMR. The effects of the solvent and temperature on ATRP of MMA were studied. The control over a large range of molecular weights was investigated with a high [MMA]/[PVAc–CCl₃] ratio for potential industry applications. In addition, the mechanism of the polymerization was discussed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1089–1094, 2006     

Decreasing miscibility with greater heterogeneity in ternary polymer blend: poly(cyclohexyl methacrylate), poly(α‐methyl styrene) and poly(4‐methyl styrene)

A ternary blend system comprising poly(cyclohexyl methacrylate) (PCHMA), poly(α‐methyl styrene) (PαMS) and poly(4‐methyl styrene) (P4MS) was investigated by thermal analysis, optical and scanning electron microscopy. Ternary phase behaviour was compared with the behaviour for the three constituent binary pairs. This study showed that the ternary blends of PCHMA/PαMS/P4MS in most compositions were miscible, with an apparent glass transition temperature (T_g) and distinct cloud‐point transitions, which were located at lower temperatures than their binary counterparts. However, in a closed‐loop range of compositions roughly near the centre of the triangular phase diagram, some ternary blends displayed phase separation with heterogeneity domains of about 1 µm. Therefore, it is properly concluded that ternary PCHMA/PαMS/P4M is partially miscible with a small closed‐loop immisciblity range, even though all the constituent binary pairs are fully miscible. Thermodynamic backgrounds leading to decreased miscibility and greater heterogeneity in a ternary polymer system in comparison with the binary counterparts are discussed. © 2003 Society of Chemical Industry     

Epoxy modification with poly(vinyl acetate) and poly(vinyl butyral). I. Structure,thermal, and mechanical characteristics

Efficiency of the application of high strength heat resistant thermoplastics for improving fracture toughness and impact properties of epoxy resins motivated authors to try large‐scale production thermoplastics for the same purpose. Epoxy/anhydride systems were modified by up to 8 wt % poly(vinyl acetate) (PVAc) and up to 6 wt % poly(vinyl butyral) (PVB). In epoxy–PVAc blends it was possible to obtain morphologies with continuous thermoplastic phase. However, only sea‐island morphologies with a very small size of PVB‐rich phase were observed in epoxy–PVB matrices. The former type of morphology allowed a notable 2.4‐fold increase in the fracture toughness of epoxy resin and simultaneous up to 30% decrease in its' impact strength. The latter type of morphology caused a notably lower (45%) enhancement of the epoxy fracture toughness combined with a 50% increase in its' impact strength. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44081.     

Miscibility and crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/poly(vinyl acetate) blends

The miscibility and crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (P(HB‐co‐HV))/poly(vinyl acetate) (PVAc) blends have been investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). It was found that P(HB‐co‐HV)/PVAc blends were miscible in the melt over the whole compositions. Thus the blend exhibited a single glass transition temperature (T_g), which increased with increasing PVAc composition. The spherulitic morphologies of P(HB‐co‐HV)/PVAc blends indicated that the PVAc was predominantly segregated into P(HB‐co‐HV) interlamellar or interfibrillar regions during P(HB‐co‐HV) crystallization because of the volume‐filled spherulites. As to the crystallization kinetics study, it was found that the overall crystallization and crystal growth rates decreased with the addition of PVAc. The kinetics retardation was primarily attributed to the reduction of chain mobility and dilution of P(HB‐co‐HV) upon mixing with higher T_g PVAc. The overall crystallization rate was predominantly governed by the spherulitic growth rate and promoted by the samples treated with the quenched state because of the higher nucleation density. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 980–988, 2006     

Synthesis of poly(vinyl acetate) containing diblock copolymer by DPE method

Diblock copolymer poly(methyl methacrylate)‐b‐poly(vinyl acetate) (PMMA‐b‐PVAc) was prepared by 1,1‐diphenylethene (DPE) method. First, free‐radical polymerization of methyl methacrylate was carried out with AIBN as initiator in the presence of DPE, giving a DPE containing PMMA precursor with controlled molecular weight. Second, vinyl acetate was polymerized in the presence of the PMMA precursor and AIBN, and PMMA‐b‐PVAc diblock copolymer with controlled molecular weight was obtained. The formation of PMMA‐b‐PVAc was confirmed by ¹H NMR spectrum. Transmission electron microscopy (TEM) and dynamic light scattering (DLS) were used to detect the self‐assembly behavior of the diblock polymer in methanol. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Phase behavior and properties of poly(methyl methacrylate)/poly(vinyl acetate) blends prepared via in situ polymerization

Polymer blends composed of poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) were prepared via radical-initiated polymerization of methyl methacrylate (MMA) in the presence of PVAc. Differential scanning calorimetry and dynamic mechanical analysis were employed to investigate the miscibility and phase behavior of the blends. The PMMA/PVAc blends of in situ polymerization were found to be phase separated and exhibited a two-phase structure, although some chain transferring reaction between the components occurred. The phase separation resulted from the solvent effect of MMA during the in situ polymerization, which was confirmed by the investigation of phase behavior based on solution cast blending. Solubility analysis of the polymerized blends indicated that some chain transferring reaction between the components occurred during the polymerization. An abrupt increase in gel content from 21.2 to 72.4 wt % was observed when the inclusion of PVAc increased from 30 to 40 wt %, and the gel component consisted of the component polymers as shown by infrared spectroscopy studies. The thermogravimetric analysis study indicated that the inclusion of a small amount of PVAc gives rise to a marked stabilization effect on the thermal stability. The PMMA/PVAc blends exhibited increased notched impact properties with the inclusion of 5 wt % PVAc. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 675–684, 1998     

Polyurethane–poly(methyl methacrylate) block copolymer dispersions through polyurethane macroiniferters

Polyurethane macroiniferter/poly(methyl methacrylate) block copolymer dispersions with inverse core‐shell morphologies were obtained from 1,1,2,2,‐tetraphenylethane‐1,2‐diol, dimethylol propionic acid, 4,4′‐diphenylmethane diisocyanate, and poly(propylene glycol) via a living radical mechanism. Molecular weight, particle size and dispersion viscosity, and thermal, mechanical, and dynamic mechanical properties of the dispersion cast films are reported as a function of copolymerization time. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1971–1975, 2003     

Morphology and thermal behavior of organo‐bentonite clay/poly(styrene‐co‐methacrylic acid)/poly(isobutyl methacrylate‐co‐4‐vinylpyridine) nanocomposites

Poly(styrene‐co‐methacrylic acid) containing 29 mol % of methacrylic acid (SMA‐29) and poly(isobutyl methacrylate‐co‐4‐vinylpyridine) containing 20 mol % of 4‐vinylpyridine (IBM4VP‐20) were synthesized, characterized, and used to elaborate binary and ternary nanocomposites of different ratios with a 3% by weight hexadecylammonium‐modified bentonite from Maghnia (Algeria) by casting method from tetrahydrofuran (THF) solutions. The morphology and the thermal behavior of these binary and ternary elaborated nanocomposites were investigated by X‐ray diffraction, scanning electron microscopy, FTIR spectroscopy, differential scanning calorimetry, and thermogravimetry. Polymer nanocomposites and nanoblends of different morphologies were obtained. The effect of the organoclay and its dispersion within the blend matrix on the phase behavior of the miscible SMA29/IBM4VP20 blends is discussed. The obtained results showed that increasing the amount of SMA29 in the IBM4VP20/SMA29 blend leads to near exfoliated nanostructure with significantly improved thermal stability. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Miscibility and morphology in blends of poly(l-lactic acid) and poly(vinyl acetate-co-vinyl alcohol)

Poly(vinyl acetate-co-vinyl alcohol) copolymers [P(VAc-co-VA)] were prepared by acidic hydrolysis of poly(vinyl acetate) (PVAc) at various reaction time, and the degree of hydrolysis was analyzed by ¹³C nuclear magnetic resonance spectroscopy (NMR). Blends of poly(l-lactic acid) (PLA) and P(VAc-co-VA) were prepared by a solvent casting method using chloroform as a co-solvent. The PLA/PVAc blends exhibited a single glass transition over the entire composition range, indicating that the blends were miscible systems. On the contrary, for the blends with even 10% hydrolyzed PVAc copolymer, the phase separation and double glass transition were observed. With increasing neat PVAc contents, the heat of fusion decreased and the melting peaks shifted to lower temperature. The interaction parameter indicated negative values for up to 10% hydrolyzed samples, but positive values at more than 20% hydrolyzed one. Small angle X-ray scattering analysis revealed that the long period and the amorphous layer thickness increased with PVAc composition, suggesting that a considerable amount of PVAc component located in the interlamellar region. Polarized optical microscopy showed that the texture of spherulites became rougher on increasing the PVAc content. In the case of P(VAc-co-VA) copolymer, the intensity of polarized light decreased significantly, indicating that P(VAc-co-VA) component seemed to be expelled out of the interfibrillar regions. Scanning electron microscopy analysis revealed that the significant phase separation occurred with increasing the degree of hydrolysis. In the case of 70/30 blend of PLA and P(VAc-co-VA) with 30 mol% vinyl alcohol, the P(VAc-co-VA) copolymer formed the regular domains with a size of about 10 μm.     

Optical study of perylene dye doped poly(methyl methacrylate) as fluorescent solar collector

The optical absorption of poly(methyl methacrylate) (PMMA), doped with perylene dye, prepared by both thermal polymerization and casting methods, has been measured before and after exposure to filtered or unfiltered light using xenon arc lamp or day light. The optical band gap of thermally polymerized PMMA was reduced by doping with perylene dye or exposure to UV radiation. Study of DSC and FTIR measurements confirmed that the samples prepared by thermal polymerization are more stable than solvent‐cast samples. © 2002 Society of Chemical Industry     

Blends of poly(vinyl acetate) and poly(ethyl methacrylate): Some mechanical properties

Poly(vinyl acetate) (PVAc) and poly(ethyl methacrylate) (PEMA) were solution blended in chloroform and cast into films on mercury surface. Some mechanical properties of the films were studied with the Instron Testing Machine. Tensile strength (TS), initial modulus (IM) and elongation at break of the films were found to depend highly on blend composition, and increased above the values for the pure polymers, each showing a peak at about 20% PEMA. The peak values of TS, IM, and elongation at break depended on an important factor, (M _v)_rc the ratio of the molecular weights of (PEMA) to (PVAc). Improvements to the mechanical properties of the polymers due to blending were considered to be as a result of the presence of favorable and strong (PVAc-PEMA) intermolecular interactions which reveal miscibility and compatibility of the polymers. A lower critical value (M _v)_rc of 4.9 was found, above which no phase separation would be expected on blending these two polymers to the extent of 20% by weight of PEMA.     

Synthesis of poly(chloroprene-co-isobutyl methacrylate) and its compatibilizing effect in polychloroprene/poly(isobutyl methacrylate) blends

A copolymer of chloroprene (CP) and isobutyl methacrylate (iBMA) [poly(CP-co-iBMA)] was prepared in benzene by radical copolymerization. For comparison, the graft copolymer of iBMA onto polychloroprene (CR) [poly(CR-g-iBMA)] was also prepared. The glass transition temperature of the poly(CP-co-iBMA) was about ?32.4°C. The monomer reactivity ratios determined by the Finneman-Ross method were given as r₁ (CP) = 1.80 and r₂ (iBMA) = 0.74 in the copolymerization of CP and iBMA, respectively. Miscibility of blends of CR and poly(isobutyl methacrylate) (PiBMA), prepared by casting from tetrahydrofuran (THF) solution, was investigated by their glass transition temperature behaviors and morphologies. Although the blends of CR and PiBMA were incompatible, the addition of poly(CP-co-iBMA) or poly(CR-g-iBMA) enhanced miscibility between the two base polymers. It was found that the extent of partial miscibility becomes larger when adding poly(CP-co-iBMA) than poly(CR-g-iBMA) as a third component to the CR/PiBMA blend of 50/50 wt % composition. © 1993 John Wiley & Sons, Inc.     

碳纳米管/PMMA/PVAC复合膜气敏性能研究(英文)

本文将一定量的PMMA、PVAc和碳纳米管在四氢呋喃溶剂中混合,通过超声分散和溶液浇铸工艺制备了碳纳米管/PMMA/PVAc复合膜.研究了在0.4-4.1ppt乙酸乙酯气氛下,碳纳米管/PMMA/PVAc复合膜电阻与气氛浓度的变化关系.研究表明:在0.4-4.1ppt气氛下,碳纳米管/PMMA/PVAc复合膜电阻随着乙酸乙酯气氛浓度的增大而增大,复合膜对乙酸乙酯气氛具有较优的敏感性,且同时随着复合膜中PMMA含量增加,复合膜电阻增加,即气敏性增加.因此,PMMA/PVAC共混物在气敏材料的应用领域上具有潜在的价值.     

Synthesis of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) and poly(vinyl alcohol)‐graft‐poly(lactide) in melt with magnesium hydride as catalyst

Grafting of poly(ε‐caprolactone) (PCL) and poly(lactide) (PLA) chains on poly(vinyl alcohol) backbone (PVA degree of hydrolysis 99%) was investigated using MgH₂ environmental catalyst and melt‐grown ring‐opening polymerization (ROP) of ε‐caprolactone (CL) and L ‐lactide (LA), that avoiding undesirable toxic catalyst and solvent. The ability of MgH₂ as catalyst as well as yield of reaction were discussed according to various PVA/CL/MgH₂ and PVA/LA/MgH₂ ratio. PVA‐g‐PCL and PVA‐g‐PLA were characterized by ¹H‐ and ¹³C‐NMR, DSC, SEC, IR. For graft copolymers easily soluble in tetrahydrofuran (THF) or chloroform, wettability and surface energy of cast film varied in relation with the length and number of hydrophobic chains. Aqueous solution of micelle‐like particles was realized by dissolution in THF then addition of water. Critical micelle concentration (CMC) decreased with hydrophobic chains. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009