Ce(IV)‐initiated graft polymerization of acrylic acid onto poly(ethylene terephthalate) fiber

Graft copolymerization of acrylic acid onto poly(ethylene terephthalate) (PET) fiber by a redox system using ceric (IV) initiator was studied with regard to various parameters of importance: acrylic acid concentration, ceric (IV) concentration, nitric acid concentration, reaction temperature, and reaction time. Based on the morphology of the PET fiber, it could be concluded that ceric (IV) in dilute nitric acid is a redox initiator for the surface graft copolymerization of the acrylic acid/PET system. The grafted PET fiber showed an increase in improved moisture regain to reach 900% at 39.5% graft yield. The dyeability with the basic dye and disperse dye significantly increased by 100 and 22%, respectively, as a result of the grafting onto PET fiber. Both tenacity and elongation gradually decreased by 51.2 and 28.9%, respectively, with increasing graft yield, which reduced the fiber service lifespan. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1952–1958, 2003     

Hydrogen peroxide initiated grafting of acrylamide onto poly(ethylene terephthalate) fibers in benzyl alcohol

The grafting of acrylamide onto poly(ethylene terephthalate) fibers using hydrogen peroxide as the redox initiator was investigated. Benzyl alcohol was found to be the favorite medium for this grafting. Maximum graft yield (7.6%) was reached at 95°C; the graft yield decreased at higher temperatures, and finally grafting was inhibited at 120°C. The effect of monomer and initiator concentration on grafting was also studied. © 1996 John Wiley & Sons, Inc.     

Graft copolymerization of methyl methacrylate onto poly(ethylene terephthalate) fibers using thallium(III) ions as initiator

Graft copolymerization of methyl methacrylate onto poly(ethylene terephthalate) fibers was investigated in aqueous perchloric acid medium using thallium(III) ions as initiator. The rate of grafting was evaluated varying the concentrations of monomer, initiator, and acid and the temperature. The rate of grafting was found to increase with increase in monomer and initiator concentrations. The graft yield was found to increase with increase in the acid concentration up to 0.49 mL^?1, and beyond this concentration it was found to decrease. Increase in temperature resulted in increase in graft yield. From the Arrhenius plot the overall activation energy was found to be 3.76 kcal/mol. The effect of additives such as swelling agents, inorganic salts, different solvents, and inhibitors on graft yield was studied. A suitable kinetic scheme is proposed and a rate equation derived.     

Surface graft copolymerization of acrylic acid onto corona-treated poly(ethylene terephthalate) fabric

Acrylic acid (AA) was grafted onto the surface of poly(ethylene terephthalate) (PET) fabric after having short-time corona-discharge treatment (CDT) in an atmosphere in the presence of the initiator. The effect of N,N-dimethylformamide (DMF) pretreatment time, CDT time, graft copolymerization time and temperature, concentration of AA, and the content of initiator on graft yield of PET fabric was discussed. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 1161–1164, 1999     

Preparation and characterization of water‐extended polyester based on recycled poly(ethylene terephthalate)

An unsaturated polyester resin was prepared that was based on the reaction of oligomers obtained from the depolymerization of poly(ethylene terephthalate) waste products, with both maleic anhydride and sebacic acid. The structure of the produced polyester was compared with that prepared from the reaction of dimethyl terephthalate with both maleic anhydride and sebacic acid with IR and NMR spectroscopy. Water‐extended polyester resins were prepared from these two polyesters through curing with styrene in the presence of various amounts of water with benzoyl peroxide as an initiator. The mechanical properties of the prepared water‐extended polyesters, as well as scanning electron microscopy, were investigated. The use of water‐extended polyesters based on recycled poly(ethylene terephthalate) waste for the preparation of decorative art objects and statues was investigated. Therefore, three pharaonic statues representing Tutankhamen, Nefertiti, and a black head of a cat were prepared. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3693–3699, 2003     

Effect of graft copolymerization of 2-hydroxyethyl methacrylate on the properties of polyester fibers and fabric

Graft copolymerization of hydroxyethyl methacrylate (HEMA) onto poly(ethylene terephthalate) (PET) fibers using benzoyl peroxide (BP) as initiator was carried out in water and in water/organic solvent as a reaction medium. The effect of initiator concentration, reaction time, temperature, and reaction medium as well as addition of FeSO₄ to the polymerization medium was studied. Percent grafting was enhanced significantly by increasing BP concentration up to 0.016 mol/L and then decreased upon further increase in initiator concentration. Increasing the monomer (HEMA) concentration up to 0.48 mol/L improves significantly the graft yield. Raising the polymerization temperature up to 85°C causes a significant increase in grafting yield; further increase in temperature leads to decrease in graft yield. Incorporation of Fe⁺² ions in the polymerization system decrease the graft yield. The same situation is encountered when water/solvent mixture is used as reaction medium. Solvent employed were methanol, toluene, and benzene.     

Grafting of ethyl acrylate onto monofilament polyester fibers using benzoyl peroxide

Ethyl acrylate was grafted onto monofilament poly(ethylene terephthalate) fibers using benzoyl peroxide as a chemical initiator. Breaking tenacity and densities of grafted fibers decreased while breaking elongation increased with the graft yield. Scanning electron micrographs showed that the fiber geometry and its diameter were not affected by grafting. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 1701–1705, 1998     

Benzoyl-peroxide-initiated graft copolymerization of poly(ethylene terephthalate) fibers with acrylamide

In this study the grafting of acrylamide onto poly(ethylene terephthalate) fibers with the help of benzoyl peroxide and the effects of the temperature and the concentrations of initiator and monomer were investigated. Some of the experiments were repeated several times in order to check the reproducibility. The optimum temperature for grafting was found to be 75°C. The graft yield was observed to increase with the monomer concentrations examined. The graft yield increased up to the benzoyl peroxide concentration approximately 0.05 g/50 mL, and then passed a plateau, before showing a decrease. The fiber diameter, intrinsic viscosity, and the moisture regain increased while the fiber density decreased with the graft yield.     

Surface modification of poly(ethylene terephthalate) fibers via controlled radical graft polymerization

Functional chemical modifications on poly(ethylene terephthalate) (PET) fibers via radical graft polymerization could be controlled by managing mutual interactions and affinities between different components in the grafting reaction system. Hansen solubility parameters was used as a tool to quantify affinities of related agents and the polymer, and provided reliable results. The latest results proved the practicality of using Hansen solubility parameters in controlling radical graft polymerizations on surface modifications of PET fibers. Four different monomers with different hydrophilic properties in different solvent and initiator systems were examined, and results confirmed that interactions of initiator‐PET, initiator‐solvent, monomer‐PET, monomer‐solvent, and monomer‐initiator play important roles in determining the grafting reaction efficiency. Results revealed that for the selected grafting systems studied, hydrophilic monomers presented overall favoring affinities toward PET leading to higher grafting yields compared to hydrophobic monomers. The results have instructive impact to commercial applications. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45990.     

Graft copolymerizaztion of methyl acrylate onto chitosan initiated by potassium diperiodatocuprate (III)

A novel redox system, potassium diperiodatocuprate [Cu (III)–chitosan], was employed to initiate the graft copolymerization of methyl acrylate (MA) onto chitosan in alkali aqueous solution. The effects of reaction variables such as monomer concentration, initiator concentration, pH and temperature were investigated. By means of a series of copolymerization reactions, the grafting conditions were optimized. Cu (III)–chitosan system was found to be an efficient redox initiator for this graft copolymerization. The structures and the thermal stability of chitosan and chitosan‐g‐poly(methyl acrylate) (PMA) were characterized by infrared spectroscopy (IR) and thermogravimetric analysis (TGA). In this article, a mechanism is proposed to explain the formation of radicals and the initiation. Finally, the graft copolymer was used as the compatibilizer in blends of poly(vinyl chloride) (PVC) and chitosan. The scanning electron microscope (SEM) photographs and differential scanning calorimetry (DSC) thermograms indicate that the graft copolymer improved the compatibility of the blend. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2283–2289, 2003     

Graft copolymerization of an itaconic acid/acrylamide monomer mixture onto poly(ethylene terephthalate) fibers with benzoyl peroxide

A mixture of acrylamide (AAm) and itaconic acid (IA) was grafted onto poly(ethylene terephthalate) (PET) fibers with benzoyl peroxide in aqueous media. The effects of polymerization conditions such as the temperature, polymerization time, initiator concentration, and monomer mixture ratio on grafting were investigated. The maximum graft yield was 76.1% with an AAm/IA mixture ratio of 90/10 (mol/mol). The graft yield was as low as 3% in the single grafting of IA, whereas the use of AAm as a comonomer increased the amount of IA that entered the fiber structure to 33.5%. An increase in the temperature from 65 to 85°C increased the grafting rate and saturation graft yield. However, an increase in the temperature above 85°C decreased the saturation graft yield. The graft yield increased up to an initiator concentration of 1.0 × 10^?2 M and decreased afterwards. The grafting rate was 0.65th‐ and 0.74th‐order with respect to the initiator and AAm concentrations, respectively. The densities, diameters, and moisture‐regain values of the AAm/IA‐grafted PET fibers increased with the graft yield. Similarly, there was an increase in the dyeability of the AAm/IA‐grafted fibers with acidic and basic dyes. The grafted fibers were characterized with Fourier transform infrared and thermogravimetric analysis, and their morphologies were examined with scanning electron microscopy. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1795–1803, 2005     

Graft copolymerization studies. III. Methyl methacrylate onto polypropylene and polyethylene terephthalate

The tert‐butoxy radical‐facilitated grafting of methyl methacrylate (MMA) onto commercial polypropylene (PP) pellets and fiber was investigated in heterogeneous conditions similar to practical systems. Free‐radical grafting of several other monomers onto PP fiber was also investigated. Also, preliminary data from the grafting of MMA onto poly(ethylene terephthalate) pellets is presented. The PP‐graft‐PMMA residues were detected by solid‐state ¹³C‐NMR and photoacoustic IR spectroscopy. There was a good correlation between the degree of grafting (DG) determined from these spectroscopic techniques and the results from gravimetric methods. A maximum grafting efficiency of over 50% was found, whereas DG (20%) remained constant at various PP pellet, initiator, and monomer concentrations. However, at relatively low PP fiber concentrations, the DG was 27%; the increase was most likely due to the greater surface area of the fiber. There was also a reduction in DG (14%) at relatively low initiator concentrations. The reaction conditions were altered to favor grafting by the addition of more polymer substrate. When the ratio of tert‐butoxy radicals to PP was decreased, more of the substrate remained unmodified, and empirical calculations showed the formation of grafts with up to 40 monomer units. At high initiator concentrations, calculations showed that the graft residues were 1–2 units long. Therefore, variation of the polymer, initiator, and monomer concentrations was shown to have a significant effect on grafting. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 898–915, 2002     

Synthesis and characterization of maleated poly(3‐hydroxybutyrate)

Graft copolymerization of maleic anhydride (MA) onto poly(3‐hydroxybutyrate) (PHB) was carried out by use of benzoyl peroxide as initiator. The effects of various polymerization conditions on graft degree were investigated, including solvents, monomer and initiator concentrations, reaction temperature, and time. The monomer and initiator concentrations played an important role in graft copolymerization, and graft degree could be controlled in the range from 0.2 to 0.85% by changing the reaction conditions. The crystallization behavior and the thermal stability of PHB and maleated PHB were studied by DSC, WAXD, optical microscopy, and TGA. The results showed that, after grafting MA, the crystallization behavior of PHB was obviously changed. The cold crystallization temperature from the glass state increased, the crystallization temperature from the melted state decreased, and the growth rate of spherulite decreased. With the increase in graft degree, the banding texture of spherulites became more distinct and orderly. Moreover, the thermal stability of maleated PHB was obviously improved, compared with that of pure PHB. Its thermal decomposition temperature was enhanced by about 20°C. In addition, the introduction of the MA group promoted the biodegradability of PHB. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 659–668, 2003     

The adsorption of Cu(II) ion from aqueous solution upon acrylic acid grafted poly(ethylene terephthalate) fibers

This study is concerned with the investigation of the adsorption properties of acrylic acid grafted poly(ethylene terephthalate) fibers by the use of Cu(II) ions in aqueous solutions. Influence of pH, graft yield, contact time, concentration of the ion, and reaction temperature on the amount of ion adsorbed upon reactive fiber were investigated. The time in which the adsorption reached to the equilibrium value was determined as 1 h. The adsorption isotherm of Cu(II) ion was found to be a Langmuir type and the heat of adsorption was calculated as ?10.1 kJ mol^?1. It was observed that the adsorbed Cu(II) ion upon acrylic acid grafted poly(ethylene terephthalate) fibers could be recovered in acidic media. The fiber could also readsorb Cu(II) ions without losing its activity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1216–1220, 2003     

Solvent-assisted graft copolymerization of acrylamide on poly(ethylene terephthalate) films using benzoyl peroxide initiator

Graft-copolymerization of acrylamide (AAm) on poly(ethylene terephthalate) (PET) films using benzoyl peroxide (Bz₂O₂) initiator has been studied. Four organic solvents, namely, pyridine (Py), 1,2-dichloroethane (DCE), DEC/H₂O (20/80, v/v), and dimethyl sulfoxide (DMSO), were used as swelling agents. DMSO was found to be the most suitable swelling agent. Solvent inclusion in the films increased with increased length of solvent treatment time and temperature. Elevated temperatures had a greater effect on the inclusion of swelling agents than did the length of swelling. Variation of graft yield with the type of solvent, initiator concentration, monomer concentration, temperature, and polymerization time were also investigated. The graft yield increased in the order of toluene, benzene, DMSO. The optimum temperature for grafting was found to be 70°C. The graft yield was observed to increase with monomer concentration and polymerization time, then reached a plateau. The graft yield increased up to a certain Bz₂O₂ concentration, then decreased. © 1993 John Wiley & Sons, Inc.     

Graft copolymerization of methyl acrylate onto poly(vinyl alcohol) initiated by potassium diperiodatonickelate(IV)

The graft copolymerization of methyl acrylate onto poly(vinyl alcohol) (PVA) with a potassium diperiodatonickelate(IV) [Ni(IV)]–PVA redox system as an initiator was investigated in an alkaline medium. The grafting parameters were determined as functions of the temperature and the concentrations of the monomer and initiator. The structures of the graft copolymers were confirmed by Fourier transform infrared spectroscopy, scanning electron microscopy, X‐ray diffraction, differential scanning calorimetry, and thermogravimetric analysis. The Ni(IV)–PVA system was found to be an efficient redox initiator for this graft copolymerization. A single‐electron‐transfer mechanism was proposed for the formation of radicals and the initiation. Other acrylate monomers, such as methyl methacrylate, ethyl acrylate, n‐butyl acrylate, and n‐butyl methacrylate, were used as reductants for graft copolymerization. These reactions definitely occurred to some degree. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 529–534, 2003     

Grafting of acrylamide–methacrylic acid mixture onto poly(ethylene terephthalate) fibers by azobisisobutyronitrile

The chemical grafting of acrylamide-methacrylic acid (AAM-MAA) mixture onto poly(ethylene terephthalate) (PET) fibers using azobisisobutyronitrile as a chemical initiator was investigated. The use of MAA as a comonomer increased the amount of AAM introduced to the PET fiber up to 33.0%, while the grafting of AAM onto fibers alone gave low graft yields. This synergistic effect was found to be at its highest when an AAM-MMA mixture having 30 wt % AAM was used. The grafting increased dyeability with both acidic and basic dyes, and increased diameter and decreased the density of the fibers. The thermogravimtric analysis results revealed that the decomposition temperature of the fibers decreased with grafting. The electron micrographs showed that grafting changed the surface morphology of the fiber and a shell-like heterogeneous structure occurred at the surface at high graft yields. © 1996 John Wiley & Sons, Inc.     

Grafting of the acrylic acid on poly(ethylene terephthalate)

A study has been made of the effect of solvent nature, concentrations of monomer, initiator and homopolymerization inhibitors, and initial polymer structure on the modification of poly(ethylene terephthalate) (PET) films and fibers by grafting the acrylic acid (AA). AA grafting initiated by radicals formed from thermal decomposition of benzoyl peroxide. It has been established that preswelling of PET in dichloroethane leads to changes in its sorption–diffusion properties and favors an increase in the degree of grafting. Addition of the Fe(II), Ni(II), and Cu(II) salts to AA solution decreased homopolymer yield. The studied process of grafting can be described by equations of diffusion kinetics. Distribution of the poly(acrylic acid) (PAA) over the cross section of samples and a number of physical and chemical properties depend also on conditions of performing the graft polymerization.     

Collagen immobilization onto the surface of artificial hair for improving the tissue adhesion

To improve the bonding ability of artificial hair towards soft tissue, type I atelocollagen was immobilized onto the hair surface. The artificial hair used was made of a poly(ethylene terephthalate) monofilament. Following photo-induced graft polymerization of a hydrophilic monomer onto the surface of artificial hair, collagen was complexed with the graft chains. Poly(acrylic acid) was selected as the polymer to be grafted onto the artificial hair because this synthetic polymer exhibited the greatest ability to form an interpolymer complex in solution with collagen among the three anionic polymers poly(acrylic acid), poly(2-acrylamido methylpropane sulfonic acid), and sodium poly(styrene sulfonic acid). When the surface of the poly(ethylene terephthalate) film used as a model substrate was grafted with poly(acrylic acid), the surface density of the collagen immobilized by interpolymer complexation was found to increase with increasing surface density of the graft chains. Immobilization of collagen onto the filament surface was confirmed by surface analysis with X-ray photoelectron spectroscopy and transmission electron microscopy. It was shown that in vitro degradation of the collagen immobilized onto poly(ethylene terephthalate) was suppressed by crosslinking the collagen molecules with glutaraldehyde. Cell culture tests revealed that L-cells were attached well to the surface of collagen-immobilized artificial hair. The surface-modified hairs were implanted percutaneously in the scalp of a human volunteer. Neither infection nor rejection of the hair filaments was observed after 1 year of implantation. It was found that the number of collagenimmobilized filaments remaining fixed in the scalp after 3 years of implantation was significantly larger than that of untreated filaments. These results indicate that surface-modified artificial hair is highly biosafe and shows excellent tissue adhesion.     

Grafting of low density poly(ethylene) with butyl acrylate: Synthesis and characterisation

Low density poly(ethylene) was grafted with butyl acrylate using benzoyl peroxide as free radical initiator in an inert atmosphere and toluene as solvent. Various parameters such as reaction time, temperature, initiator concentration and ratio of monomer to polymer were varied to study their effects on percentage of grafting and grafting efficiency of butyl acrylate on to low density poly(ethylene). The graft copolymers were characterised by IR spectroscopy. The change in the solubility behaviour of low density poly(ethylene) due to grafting was studied by turbidometric titration. Thermal stability of graft copolymers was found to be higher than that of LDPE. Intrinsic viscosity data showed an increase in viscosity with increasing grafting percentage.