Study on the microstructure and properties of bromobutyl rubber (BIIR)/polyamide‐12 (PA12) thermoplastic vulcanizates (TPVs)

In this study, polyamide‐12 (PA12)/brominated isobutylene‐isoprene (BIIR) TPVs with good mechanical properties and low gas permeability were prepared by dynamic vulcanization in a twin‐screw extruder. The effects of three kinds of compatibilizers on the microstructure and properties of BIIR/PA12 TPV were studied. The compatibility between BIIR and PA12 was improved when maleated hydrocarbon polymeric compatibilizer is added. The reaction between maleic anhydride and amine in polyamide leads to the in situ formation of hydrocarbon polymer grafted polyamide which subsequently can be used to lower the interfacial tension between BIIR and polyamide. The compatibilizing effect of maleic anhydride modified polypropylene (PP‐g‐MAH) on BIIR/PA12 blends is the best among these compatibilizers because the surface energy of PP‐g‐MAH is very close to that of BIIR. The dispersed rubber phase of the blend compatibilized by PP‐g‐MAH shows the smallest size and more uniform size distribution, and the resulting TPVs show the best mechanical properties. The effects of fillers on the properties of BIIR/PA12 TPV were also investigated. The size of the BIIR phase increases with the increase in the content of CaCO₃. The modulus and tensile strength of TPVs increased with the increase in the content of CaCO₃ because of the reinforcing effect of CaCO₃ on TPVs. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43043.     

Morphological evolution and properties of thermoplastic vulcanizate/organoclay nanocomposites

Nanocomposites composed of organoclay and thermoplastic vulcanizates (TPVs) based on uncompatibilized or compatibilized polypropylene (PP)/ethylene–propylene–diene rubber (EPDM) blends were prepared in this study. The morphology of the nanocomposites was studied with wide‐angle X‐ray diffraction and transmission electron microscopy, which suggested that the addition of the compatibilizer played a key role in determining the morphology of the composites because of their interaction with the clay surface. Scanning electron microscopy study indicated the changes in the morphology of the rubber particles. Dynamic mechanical analysis was also applied to the analysis of these phenomena. Moreover, for nanocomposites with uncompatibilized PP/EPDM blends as the matrix, the samples showed tensile enhancement compared with neat TPV. Although the addition of the compatibilizer changed tensile properties of the composites in a rather different trend, the tensile modulus increased dramatically when the compatibilizer was added. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40618.     

In situ dynamic vulcanization process in preparation of electrically conductive PP/EPDM thermoplastic vulcanizate/expanded graphite nanocomposites: Effects of state of cure

In situ melt dynamic vulcanization process has been employed to prepare electrically conductive polypropylene (PP)/ethylene–propylene–diene rubber (EPDM) (40/60 wt %) thermoplastic vulcanizates (TPVs) incorporated by expanded graphite (EG) as a conductive filler. Maleic anhydride grafted PP (PP‐g‐MAH) was used as compatibilizer and a sulfur curing system was designed and incorporated to vulcanize the EPDM phase during mixing process. Developed microstructures were characterized using scanning electron microscopy (SEM), melt rheomechanical spectroscopy (RMS), X‐ray diffraction (XRD), and transmission electron microscopy (TEM) and were correlated with electrical conductivity behavior. For comparison, another class of TPV/EG nanocomposites was fabricated using a commercially available PP/EPDM‐based TPV via both direct and masterbatch melt mixing process. Conductivity of the nanocomposites prepared by in situ showed no significant change during dynamic vulcanization till the mixing torque reached to the stationary level where micro‐morphology of the cured rubber droplets was fully developed, and conductivity abrupt was observed. In situ cured nanocomposites showed higher insulator to conductor transition threshold (3.15 vol % EG) than those based on commercially available TPV. All electrically conductive in situ prepared TPV nanocomposites exhibited reinforced melt elasticity with pseudosolid‐like behavior within low frequency region in dynamic melt rheometry indicating formation of physical networks by both EG nanolayers and crosslinked EPDM droplets. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Toughening of PP/EPDM blend by compatibilization

To improve the mechanical properties of blends of polypropylene (PP) and terpolymer of ethylene–propylene–diene (EPDM), a triblock copolymer, (PP‐g‐MAH)‐co‐[PA‐6,6]‐co‐(EPDM‐g‐MAH), was synthesized by coupling reaction of maleic anhydride (MAH)‐grafted PP (PP‐g‐MAH), EPDM‐g‐MAH, and PA‐6,6. The newly prepared block copolymer brought about a physical interlocking between the blend components, and imparted a compatibilizing effect to the blends. Introducing the block copolymer to the blends up to 5 wt % lead to formation of a β‐form crystal. The wide‐angle X‐ray diffractograms measured in the region of 2θ between 10° and 50° ascertained that incorporating the block copolymer gave a new peak at 2θ = 15.8°. The new peak was assigned to the (300) plane spacings of the β‐hexagonal crystal structure. In addition, the block copolymer notably improved the low‐temperature impact property of the PP/EPDM blends. The optimum usage level of the compatibilizer proved to be 0.5 wt %. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1267–1274, 2000     

Design and properties of a series of high‐temperature thermoplastic elastomeric blends from polyamides and functionalized rubbers

A series of high‐temperature thermoplastic elastomers (TPEs) and thermoplastic vulcanisates (TPVs) were successfully developed based on two different types of heat resistant polyamide (PA) (25 parts by weight)—PA‐12 and PA‐6, in combination with three different functionalized rubbers (75 parts by weight) of varying polarity, e.g., maleic anhydride grafted ethylene propylene diene terpolymer (MA‐g‐EPDM), sulphonated ethylene propylene diene terpolymer, and carboxylated acrylonitrile butadiene rubber, by melt mixing method. These rubbers have low level of unsaturation in its backbone, and the plastics showed high melting range. Thus, the developed TPEs and TPVs were expected to be high temperature resistant. Resol type resin was used for dynamic vulcanization to further increase the high temperature properties of these blends. Interestingly, initial degradation temperature of the prepared blends was much higher (421 °C for MA‐g‐EPDM/PA‐12) than the other reported conventional TPEs and TPVs. Fourier transform infrared analysis described the interactive nature of the TPEs and TPVs, which is responsible for their superior properties. The maximum tensile strength with lowest tension set was observed for the carboxylated acrylonitrile butadiene rubber/PA‐12 TPV. Mild increase in mechanical properties without any degradation was observed after recycling. Dynamic mechanical analysis results showed two distinct glass transition temperatures and indicated the biphasic morphology of the blends, as evident from the scanning electron microscopy. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45353.     

Compatibilizing effect of ethylene–propylene–diene grafted maleic anhydride terpolymer on the blend of polyamide 66 and thermal liquid crystalline polymer

Polyamide 66–thermal liquid crystalline polymer (PA66/TLCP) composites containing 10 wt% TLCP was compatibilized by ethylene–propylene–diene‐grafted maleic anhydride terpolymer (MAH‐g‐EPDM). The blending was performed on a twin‐screw extrusion, followed by an injection molding. The rheological, dynamic mechanical analysis (DMA), thermal, mechanical properties, as well as the morphology and FTIR spectra, of the blends were investigated and discussed. Rheological, DMA, and FTIR spectra results showed that MAH‐g‐EPDM is an effective compatibilizer for PA66/TLCP blends. The mechanical test indicated that the tensile strength, tensile elongation, and the bending strength of the blends were improved with the increase of the content of MAH‐g‐EPDM, which implied that the blends probably have a great frictional shear force, resulting from strong adhesion at the interface between the matrix and the dispersion phase; while the bending modulus was weakened with the increase of MAH‐g‐EPDM content, which is attributed to the development of the crystalline phase of PA66 hampered by adding MAH‐g‐EPDM. POLYM. COMPOS., 27:608–613, 2006. © 2006 Society of Plastics Engineers     

Dynamic mechanical properties of polypropylene‐g‐maleic anhydride and ethylene–propylene–diene terpolymer blends: Effect of blend preparation methods

In this work, we attempted two different ways of processing to improve interfacial adhesion of polypropylene (PP) and ethylene–propylene–diene terpolymer (EPDM) by introducing maleic anhydride (MAH); In one way, the in situ grafting and dynamic vulcanization (ISGV) were performed simultaneously from PP and EPDM with MAH in the presence of dicumyl peroxide (DCP) in an intensive mixer. In another way, PP was first grafted with MAH and then the PP‐g‐MAH was blended with EPDM in the intensive mixer in the presence of DCP by the dynamic vulcanization (DV). It was found that the glass transition temperatures (T_gs) of both PP and EPDM phases were shifted to higher temperature as the EPDM content increased for the blends prepared by both IGSV and DV methods, mainly due to the crosslinking of EPDM. The higher T_gs and larger storage moduli were observed for the blends prepared by the ISGV method than those prepared by the DV method, while the morphology showed that the size reduction of dispersed particles in latter blends was larger than that of the former blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2777–2784, 2000     

Effects of compounding procedure on morphology development,melt rheology,and mechanical properties of nanoclay reinforced dynamically vulcanized EPDM/polypropylene thermoplastic vulcanizates

New nanocomposite thermoplastic vulcanizates (TPVs) comprising dynamically cross‐linked nanoscale EPDM rubber particles dispersed throughout the polypropylene (PP) matrix have been prepared by both batch and continuous melt blending of PP with EPDM in the presence of vulcanizing ingredients, nanoclay and maleated EPDM (EPDM‐g‐MA) as compatibilizer. X‐ray diffraction, linear melt viscoelastic measurement, and tensile mechanical behavior results revealed that the developed microstructure is strongly affected by the type of the melt compounding process as well as the route of material feeding. When EPDM phase was precompounded with a vulcanizing agent, nanoclay, and EPDM‐g‐MA prior to the melt blending with PP, not only nanosize cross‐linked rubber particles appeared uniformly throughout the PP continuous phase, but also the melt blending leads to the significant enhancement of the mechanical properties compared with counterpart samples prepared by one‐step melt mixing process. Also better dispersion of nano layers in the rubber compound before melt blending with PP results in higher mechanical properties of the resulted TPV. POLYM. ENG. SCI., 56:914–921, 2016. © 2016 Society of Plastics Engineers     

Dynamically vulcanized acrylonitrile–butadiene–styrene terpolymer/nitrile butadiene rubber blends compatibilized by chlorinated polyethylene

Thermoplastic vulcanizates (TPVs) based on acrylonitrile–butadiene–styrene (ABS)/nitrile butadiene rubber (NBR) blends were prepared by dynamic vulcanization and then compatibilized by chlorinated polyethylene (CM). The effects of CM compatibilizer on the mechanical properties, Mullins effect, and morphological and dynamic mechanical properties of the TPVs were investigated systematically. Experimental results indicated that CM had an excellent compatibilization effect on the dynamically vulcanized ABS/NBR TPVs. Mullins effect results showed that the compatibilized ABS/NBR TPV had relatively lower internal friction loss than the ABS/NBR TPV, indicating the improvement of elasticity. Morphology studies showed that the fracture surfaces of ABS/CM/NBR TPVs were relatively smoother, indicating the improved elastic reversibility. DMA studies showed that the glass to rubber transition temperatures of ABS and NBR phases were slightly shifted toward each other with the incorporation of CM compatibilizer, which indicates the improvement of the compatibility. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40986.     

Thermoplastic vulcanizates based on epoxidized natural rubber/polypropylene blends: Effect of compatibilizers and reactive blending

Epoxidized natural rubber (ENR) was prepared using the performic epoxidation method. TPVs based on ENR/PP blends were later prepared by melt‐mixing processes via dynamic vulcanization. The effects of blend ratios of ENR/PP, types of compatibilizers, and reactive blending were investigated. Phenolic modified polypropylene (Ph‐PP) and graft copolymer of maleic anhydride on polypropylene molecules (PP‐g‐MA) were prepared and used as blend compatibilizers and reactive blending components of ENR/Ph‐PP and ENR/PP‐g‐MA blends. It was found that the mixing torque, apparent shear stress and apparent shear viscosity increased with increasing levels of ENR. This is attributed to the higher viscosity of the pure ENR than that of the pure PP. Furthermore, there was a higher compatibilizing effect because of the chemical interaction between the polar groups in ENR and PP‐g‐MA or Ph‐PP. Mixing torque, shear flow properties (i.e., shear stress and shear viscosity) and mechanical properties (i.e., tensile strength, elongation at break, and hardness) of the TPVs prepared by reactive blending of ENR/Ph‐PP and ENR/PP‐g‐MA were lower than that of the samples without a compatibilizer. However, the TPVs prepared using Ph‐PP and PP‐g‐MA as compatibilizers exhibited higher values. We observed that the TPVs prepared from ENR/PP with Ph‐PP as a compatibilizer gave the highest rheological and mechanical properties, while the reactive blending of ENR/PP exhibited the lowest values. Trend of the properties corresponds to the morphology of the TPVs. That is, the TPV with Ph‐PP as a blend compatibilizer showed the smallest rubber particles dispersed in the PP matrix, while the reactive blending of ENR/PP‐g‐MA showed the largest particles. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4729–4740, 2006     

Effect of the compatibilizer on the morphology and properties of dynamically cured PP/POE/epoxy blends

Dynamic vulcanization was successfully applied to epoxy resin reinforced polypropylene (PP)/ethylene‐octene copolymer (POE) blends, and the effects of different compatibilizers on the morphology and properties of dynamically cured PP/POE/epoxy blends were studied. The results show that dynamically cured PP/POE/epoxy blends compatibilized with maleic anhydride‐grafted polypropylene (MAH‐g‐PP) have a three‐phase structure consisting of POE and epoxy particles dispersed in the PP continuous phase, and these blends had improved tensile strength and flexural modulus. While using maleic anhydride‐grafted POE (MAH‐g‐POE) as a compatibilizer, the structure of the core‐shell complex phase and the PP continuous phase showed that epoxy particles could be embedded in MAH‐g‐POE in the blends, and gave rise to an increase in impact strength, while retaining a certain strength and modulus. DSC analysis showed that the epoxy particles in the blends compatibilized with MAH‐g‐PP were more efficient nucleating agents for PP than they were in the blends compatibilized with MAH‐g‐POE. WAXD analysis shows that compatibilization do not disturb the crystalline structure of PP in the blends. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Dynamic properties of rubber vibration isolators and antivibration performance of ethylene–propylene–diene monomer/nylon 6 blend systems

This article examines thermoplastic elastomers (TPEs) and thermoplastic vulcanizates (TPVs) as two types of elastomers from melt-blended and dynamically vulcanized ethylene–propylene–diene monomer (EPDM) rubber materials and nylon 6 plastic materials. A series of investigations were conducted on the mechanical properties, morphology, dynamic mechanical properties, hysteresis behavior, and dynamic antivibration properties with different nylon 6 contents. The experimental results showed that the incompatibility between EPDM and nylon 6 led to the easy destruction of the TPV materials in two interfacial polymers upon the application of an external force. Thus, after a dynamic vulcanization process, the mechanical properties of the EPDM/nylon 6 blends were not as good as those of the TPE materials. In terms of morphology, nylon 6 plastics were uniformly distributed in the EPDM/nylon 6 blends during the EPDM rubber phase before vulcanization was performed. After the dynamic vulcanization, phase inversion was produced in which rubber microparticles were formed and dispersed in the nylon 6 plastic phase. The results of dynamic mechanical analysis, compression vibration hysteresis behavior, and dynamic property antivibration experiments showed that the blends provided better vibration isolation and antivibration performance after the amount of nylon 6 was increased and EPDM and nylon 6 were blended through dynamic vulcanization. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Rheological,thermal, and morphological properties of blends based on poly(propylene), ethylene propylene rubber,and ethylene-1-octene copolymer that could result from end of life vehicles: Effect of maleic anhydride grafted poly(propylene)

The objective of this work is to study the properties of blends that could result from the recycling of end-of-life vehicles (ELV). While ethylene propylene rubber (EPR) and ethylene propylene diene monomer (EPDM) have been used extensively as elastomeric additives in poly(propylene) (PP), they can be substituted by ethylene-1-octene copolymer (EOC). As a consequence, the matter resulting from the sorting of ELV might be more complex and made of PP, EPR, and EOC. The effect of incorporating EOC [that is a polyethylene elastomer (PEE)] and maleic anhydride grafted polypropylene (PP-g-MAH) on the rheological, thermal, and morphological properties of PP/EPR blends has been investigated. Blends of various compositions (with and without compatibilizer) were prepared using a corotating twin-screw extruder. The results were compared to the ones presented by a commercial (PP/EPR) blend. The EPR phase is dispersed in the form of spherical particles in (PP/EPR). The EOC phase is dispersed in the form of aggregated particles. Dynamic viscoelastic and differential scanning calorimetry properties of (PP/EPR)/EOC blends shows the incompatibility of the components even in presence of PP-g-MAH copolymer. POLYM. ENG. SCI., 47:1009–1015, 2007. © 2007 Society of Plastics Engineers     

Polyamide 6/maleated ethylene–propylene–diene rubber/organoclay composites with or without glycidyl methacrylate as a compatibilizer

Polyamide 6 (PA6)/maleated ethylene–propylene–diene rubber (EPDM‐g‐MA)/organoclay (OMMT) composites were melt‐compounded through two blending sequences. Glycidyl methacrylate (GMA) was used as a compatibilizer for the ternary composites. The composite prepared through via the premixing of PA6 with OMMT and then further melt blending with EPDM‐g‐MA exhibited higher impact strength than the composite prepared through the simultaneous blending of all the components. However, satisfactorily balanced mechanical properties could be achieved by the addition of GMA through a one‐step blending sequence. The addition of GMA improved the compatibility between PA6 and EPDM‐g‐MA, and this was due to the reactions between PA6, EPDM‐g‐MA, and GMA, as proved by Fourier transform infrared analysis and solubility (Molau) testing. In addition, OMMT acted as a compatibilizer for PA6/EPDM‐g‐MA blends at low contents, but it weakened the interfacial interactions between PA6 and EPDM‐g‐MA at high contents. Both OMMT and GMA retarded the crystallization of PA6. The complex viscosity, storage modulus, and loss modulus of the composites were obviously affected by the addition of OMMT and GMA. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Fractionated crystallization of dispersed PA6 phase of PP/PP‐g‐MAH/PA6 blends

Fractionated crystallization behavior of dispersed PA6 phase in PP/PA6 blends compatibilized with PP‐g‐MAH was investigated by scanning electron microscopy (SEM), differential scanning calorimeter (DSC), polarized light microscopy (PLM), and wide‐angle X‐ray diffraction (WAXD) in this work. The lack of usual active heterogeneities in the dispersed droplet was the key factor for the fractionated crystallization of PA6. The crystals formed with less efficient nuclei might contain more defects in the crystal structures than those crystallized with the usual active nuclei. The lower the crystallization temperature, the lesser the perfection of the crystals and the lower crystallinity would be. The fractionated crystallization of PP droplets encapsulated by PA6 domains was also observed. The effect of existing PP‐g‐MAH‐g‐PA6 copolymer located at the interface on the fractionated crystallization could not be detected in this work. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3742–3755, 2004     

Dynamically cured polypropylene/epoxy blends

The dynamic vulcanization process, usually used for the preparation of thermoplastic elastomers, was used to prepare polypropylene (PP)/epoxy blends. The blends had crosslinked epoxy resin particles finely dispersed in the PP matrix, and they were called dynamically cured PP/epoxy blends. Maleic anhydride grafted polypropylene (MAH‐g‐PP) was used as a compatibilizer. The effects of the reactive compatibilization and dynamic cure were studied with rheometry, capillary rheometry, and scanning electron microscopy (SEM). The crystallization behavior and mechanical properties of PP/epoxy, PP/MAH‐g‐PP/epoxy, and dynamically cured PP/epoxy blends were also investigated. The increase in the torque at equilibrium for the PP/MAH‐g‐PP/epoxy blends indicated the reaction between maleic anhydride groups of MAH‐g‐PP and the epoxy resin. The torque at equilibrium of the dynamically cured PP/epoxy blends increased with increasing epoxy resin content. Capillary rheological measurements also showed that the addition of MAH‐g‐PP or an increasing epoxy resin content increased the viscosity of PP/epoxy blends. SEM micrographs indicated that the PP/epoxy blends compatibilized with PP/MAH‐g‐PP had finer domains and more obscure boundaries than the PP/epoxy blends. A shift of the crystallization peak to a higher temperature for all the PP/epoxy blends indicated that uncured and cured epoxy resin particles in the blends could act as effective nucleating agents. The spherulites of pure PP were larger than those of PP in the PP/epoxy, PP/MAH‐g‐PP/epoxy, and dynamically cured PP/epoxy blends, as measured by polarized optical microscopy. The dynamically cured PP/epoxy blends had better mechanical properties than the PP/epoxy and PP/MAH‐g‐PP/epoxy blends. With increasing epoxy resin content, the flexural modulus of all the blends increased significantly, and the impact strength and tensile strength increased slightly, whereas the elongation at break decreased dramatically. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1437–1448, 2004     

Solution maleation of EPDM and blending of acetal copolymer with rubber using maleated EPDM as compatibilizer

Maleation of EPDM in xylene solution using dibenzoyl peroxide as initiator at the boiling point of solution was studied. Effects of amounts of dibenzoyl peroxide and maleic anhydride (MAH), reaction time and temperature, as well as the concentration of EPDM on the bond MAH content of the product were investigated. The results showed that by optimization of the maleation conditions, maleated product with high bond MAH content up to 20 wt % can be obtained without gelation. The maleated EPDM (MEPDM) was utilized in the blending of acetal copolymer and rubber such as EPDM or cis-1,4-polybutadiene. Both the impact strength and the tensile strength of the blends increased when a certain amount of MEPDM was added. Decrease of crystallinity of acetal copolymer in the blends determined by wide angle X-ray diffraction and morphology of the blends examined by scanning electron microscope demonstrated the action of MEPDM as compatibilizer. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 329–335, 1997     

Effect of EPDM‐g‐MAH on the morphology and properties of PA6/EPDM/HDPE ternary blends

The formation of core‐shell morphology within the dispersed phase was studied for composite droplet polymer‐blend systems comprising a polyamide‐6 matrix, ethylene‐propylene‐diene terpolymer (EPDM) shell and high density polyethylene (HDPE) core. In this article, the effect of EPDM with different molecular weights on the morphology and properties of the blends were studied. To improve the compatibility of the ternary blends, EPDM was modified by grafting with maleic anhydride (EPDM‐g‐MAH). It was found that core‐shell morphology with EPDM‐g‐MAH as shell and HDPE as core and separated dispersion morphology of EPDM‐g‐MAH and HDPE phase were obtained separately in PA6 matrix with different molecular weights of EPDM‐g‐MAH in the blends. DSC measurement indicated that there may be some co‐crystals in the blends due to the formation of core‐shell structure. Mechanical tests showed that PA6/EPDM‐g‐MAH/HDPE ternary blends with the core‐shell morphology exhibited a remarkable rise in the elongation at break. With more perfect core‐shell composite droplets and co‐crystals, the impact strength of the ternary blends could be greatly increased to 51.38 kJ m^?2, almost 10 times higher than that of pure PA6 (5.50 kJ m^?2). POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Crystallization behavior of PP/PP‐g‐MAH/GFR PA66 blends: Establishment of their continuous‐cooling‐transformation of relative crystallinity diagrams

Polypropylene/polypropylene‐grafted‐maleic anhydride/glass fiber reinforced polyamide 66 (PP/PP‐g‐MAH/GFR PA 66) blends‐composites with and without the addition of polypropylene‐grafted‐maleic anhydride (PP‐g‐MAH) were prepared in a twin screw extruder. The effect of the compatibilizer on the thermal properties and crystallization behavior was determined using differential scanning calorimetry analysis. The hold time was set to be equal to 5 min at 290°C. These conditions are necessary to eliminate the thermomechanical history in the molten state. The crystallization under nonisothermal conditions and the plot of Continuous‐Cooling‐Transformation of relative crystallinity diagrams of both PP and PA 66 components proves that PP is significantly affected by the presence of PP‐g‐MAH. From the results it is found that an abrupt change is observed at 2.5 wt % of PP‐g‐MAH as a compatibilizer and then levels off. In these blends, concurrent crystallization behavior was not observed for GFR PA66. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1620–1626, 2007     

Waste ground rubber tire powder/thermoplastic vulcanizate blends: Preparation,characterization, and compatibility

In this article, waste ground rubber tire (WGRT) powder was introduced into thermoplastic vulcanizate (TPV) to prepare the blends of WGRT powder/TPV. The mechanical, rheological, thermal aging, and dynamic properties of the blends were investigated with respect to the particle size and dosage of WGRT powder. The results showed that tensile strength, tear strength, elongation at break, and tensile permanent deformation of the blends increased with the decrease in WGRT particle size and decreased with the dosage of WGRT. The effects of different types and dosages of compatibilizers on mechanical and rheological properties of the blends were studied. The results showed that the compatibilizer PP‐g‐MAH could effectively improve the interfacial compatibility between WGRT and the TPV matrix to enhance the comprehensive properties of blends. The TPV/WGRT/PP‐g‐MAH blends obtained the best overall properties when prepared at the weight ratio 100/30/5. Rheological studies demonstrated that the WGRT/TPV blends represented lower apparent viscosity after PP‐g‐MAH were added, which means that processing performance of the blends was improved by PP‐g‐MAH. Scanning electron microscopy was used to study the morphologies of the blends. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39868.