Crystallization and melting behavior of poly(p‐phenylene sulfide) in blends with poly(ether sulfone)

Crystallization and melting behaviors of poly(p‐phenylene sulfide) (PPS) in blends with poly(ether sulfone) (PES) prepared by melt‐mixing were investigated by differential scanning calorimetry (DSC). The blends showed two glass transition temperatures corresponding to PPS‐ and PES‐rich phases, which increased with increasing PES content, indicating that PPS and PES have some compatibility. The cold crystallization temperature of the blended PPS was a little higher than that of pure PPS. Also, the heats of crystallization and melting of the blended PPS decreased with increasing PES content, indicating that the degree of crystallinity decreased with an increase of PES content. The isothermal crystallization studies revealed that the crystallization of PPS is accelerated by blending PPS with 10 wt % PES and further addition results in the retardation. The Avrami exponent n was about 4 independent on blend composition. The activation energy of crystallization increased by blending with PES. The equilibrium melting point decreased linearly with increasing PES content. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1686–1692, 1999     

Poly(ether ether ketone)/poly(aryl ether sulfone) blends: Relationships between morphology and mechanical properties

Mechanical properties such as the tensile modulus, yield (break) strength, and elongation to break (or yield) are measured for multiphase poly(ether ether ketone) (PEEK)/poly(aryl ether sulfone) (PES) blends. Specimens with three different levels of thermal histories (quenched, as‐molded, and annealed) are prepared in order to study their effects on the mechanical properties of PEEK/PES blends. Synergistic behavior is observed in the tensile modulus and tensile strength of the blends in almost the whole range of compositions. The ductility of quenched blends measured as the elongation to break (yield) shows an unexpected synergistic behavior in the blend containing 90 wt % PEEK, although a negative deviation from additive behavior is observed in the rest of the compositions. A ductile–brittle transition is observed between 50 and 75 wt % PEEK in the blend. The ductile–brittle transition in as‐molded blends shifts to 75–90 wt % PEEK. Annealed blends show predominantly brittle behavior in the whole composition range. The experimental data are further correlated with the theoretically predicted results based on various composite models. Although the prediction based on these equations fails to fit the experimental data in the whole composition range, the simplex equations that are normally used for blends showing synergistic behavior produced a reasonable fit to the experimental data. The mechanical properties obtained for different blend compositions are further correlated with their morphology as observed by scanning electron microscopy. Morphological observation shows a two‐phase morphology in PES‐rich blends, which is an interlocked morphology in which the disperse phase is not clearly visible in PEEK‐rich blends, and a cocontinuous type of morphology for a 50/50 composition. Considerable permanent deformation of both the disperse and matrix phase, especially in the case of quenched tensile specimens, demonstrates the remarkable adhesion present between the two phases. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2887–2905, 2003     

Miscibility and crystallization behavior of poly(ether ether ketone ketone)/poly(ether imide) blends

The miscibility and crystallization behavior of poly(ether ether ketone ketone) (PEEKK)/poly(ether imide) (PEI) blends prepared by melt‐mixing were investigated by differential scanning calorimetry. The blends showed a single glass transition temperature, which increased with increasing PEI content, indicating that PEEKK and PEI are completely miscible in the amorphous phase over the studied composition range (weight ratio: 90/10–60/40). The cold crystallization of PEEKK blended with PEI was retarded by the presence of PEI, as is apparent from the increase of the cold crystallization temperature and decrease of the normalized crystallinity for the samples anealed at 300°C with increasing PEI content. Although the depression of the apparent melting temperature of PEEKK blended with PEI was observed, there was no evidence of depression in the equilibrium melting temperature. The analysis of the isothermal crystallization at 313–321°C from the melt of PEEKK/PEI (100/0, 90/10, and 80/20) blends suggested that the retardation of crystallization of PEEKK is caused by the increase of the crystal surface free energy in addition to the decrease of the mobility by blending PEI with a high glass transition temperature. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 769–775, 2001     

Rheological properties in blends of poly(aryl ether ether ketone) and liquid crystalline poly(aryl ether ketone)

Rheological properties of the blends of poly(aryl ether ether ketone) (PEEK) with liquid crystalline poly(aryl ether ketone) containing substituted 3‐trifluoromethylbenzene side group (F‐PAEK), prepared by solution precipitation, have been investigated by rheometer. Dynamic rheological behaviors of the blends under the oscillatory shear mode are strongly dependent on blend composition. For PEEK‐rich blends, the systems show flow curves similar to those of the pure PEEK, i.e., dynamic storage modulus G′ is larger than dynamic loss modulus G″, showing the feature of elastic fluid. For F‐PAEK‐rich systems, the rheological behavior of the blends has a resemblance to pure F‐PAEK, i.e., G″ is greater than G′, showing the characteristic of viscous fluid. When the PEEK content is in the range of 50–70%, the blends exhibit an unusual rheological behavior, which is the result of phase inversion between the two components. Moreover, as a whole, the complex viscosity values of the blends are between those of two pure polymers and decrease with increasing F‐PAEK content. However, at 50% weight fraction of PEEK, the viscosity‐composition curves exhibit a local maximum, which may be mainly attributed to the phase separation of two components at such a composition. The changes of G′ and G″ with composition show a trend similar to that of complex viscosity. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4040–4044, 2006     

Investigation on the crystallization behavior of poly(ether ether ketone)/poly(phenylene sulfide) blends

The morphology of nonisothermally crystallized poly(phenylene sulfide) (PPS) and its blend with poly (ether ether ketone) (PEEK) have been observed by polarized optical microscope (POM) equipped with a hot stage. The nonisothermal crystallization behavior of PPS and PEEK/PPS blend has also been investigated by differential scanning calorimetry (DSC). The maximum crystallization temperature for PEEK/PPS blend is about 15°C higher than that of neat PPS, and the crystallization rate, characterized by half crystallization time, of the PEEK/PPS blend is also higher than that of the neat PPS. These results indicate that the PEEK acts as an effective nucleation agent and greatly accelerates the crystallization rate of PPS. The Ozawa model was used to analyze the nonisothermal crystallization kinetics of PPS and its blends. The Avrami exponent values of neat PPS are higher than that of its blend, which shows that the presence of PEEK changed the nucleation type of PPS from homogeneous nucleation to heterogeneous nucleation. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

聚醚醚酮共混改性研究进展

综述了聚醚醚酮（PEEK）、聚醚酰亚胺（PEI）、聚四氟乙烯（PTFE）、热致液晶（TLCP）和聚醚砜（PES）等高性能工程塑料的共混改性研究进展,详细探讨了各种PEEK共混物的相容性、结晶行为、微观结构、热行为和力学性能等性能特征。PEEK与PEI在熔融和无定形状态下完全相容,常用于PEEK的结晶行为和微观结构的基础研究;与PTFE、TLCP、PES共混分别是提高PEEK的摩擦磨损性能、加工性能和热稳定性的有效手段。各种共混物的相容性好坏对其结晶行为和微观结构有重要影响,从而影响了共混物的力学性能。在此基础上,对PEEK共混改性领域进一步的研究方向和内容进行了讨论。     

Spherulitic growth kinetics in miscible blends of poly(ether ether ketone) and poly(ether imide)

Growths of poly(ether ether ketone) (PEEK) spherulites from both pure melt and its miscible blends with poly(ether imide) (PEI) have been studied by polarized optical microscopy. The nucleation density of PEEK spherulites was depressed upon blending with PEI, which can be attributed to the reduction in degree of supercooling arising from equilibrium melting point depression. A modified Lauritzen-Hoffman (L-H) theory was adopted to analyze the growth kinetics. Regime III-II transition was observed with the transition temperature decreasing with increasing PEI composition. Assuming free rotations of the virtual bonds in PEEK molecule, the side surface free energy of 12.0 erg/cm² was calculated from the characteristic ratio. The fold surface free energy of 188 erg/cm² and work of chain folding of 12.3 kcal/mol were then obtained from the modified L-H analysis.     

Mechanical properties,morphology, and crystallization behavior of new thermoplastic polyimide (N‐TPI)/poly(ether sulfone) blends

Blends of wholly aromatic new thermoplastic polyimide (N‐TPI) and poly(ether sulfone) (PES) were prepared by melt‐mixing and subsequent injection molding. Their mechanical properties, morphology, and crystallization behavior were investigated. A synergistic effect on the flexural properties was observed for the N‐TPI/PES blends over the whole compositions. Differential scanning calorimetric analysis confirmed that the blend is an immiscible system and that the crystallinity of the N‐TPI component is very low (0.4–1.4%) irrespective of the composition. Scanning electron microscopic analysis suggested that the improvement in flexural properties is likely due to the reinforcement of the PES matrix by the fibrous N‐TPI phase for the N‐TPI/PES (40/60, 20/80) blends. For N‐TPI/PES (80/20, 60/40), the orientation of the matrix N‐TPI rather than the fibrillation of the PES phase along the melt‐flow direction may contribute to the synergism observed. Also, study of the isothermal crystallization behavior of the blends revealed that the addition of 10 wt % PES accelerates the crystallization of N‐TPI and further addition causes the retardation of it. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1366–1374, 2002     

Hollow fiber microfiltration membranes from poly(ether ether ketone) (PEEK)

A procedure for obtaining high performance large internal diameter (ID; >1 mm) hollow fiber microfiltration membranes from poly(ether ether ketone) (PEEK) is presented. A simple mixture of isomers of diphenylphthalate is a good solvent for employing the thermal‐phase inversion process to obtain PEEK membranes. Obtaining large ID hollow fibers with substantial transmembrane flux requires sufficient melt strength during spinning to prevent excessive draw of the extruding fiber. The use of a second leachable polymer to the blend satisfies the conditions, and polysulphone (PS) is found to provide superior membranes relative to either poly(etherimide) (PEI) or poly(ether sulphone) (PES) as a second polymer. PEEK membranes obtained by this process yield better chemical resistance to a concentrated warm surfactant/oil solution. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 175–181, 1999     

Thermal behavior of poly(ether ketone ketone)/thermoplastic polyimide blends

The phase behavior and crystallization of poly(ether ketone ketone)/polyimide blends was investigated by differential scanning calorimetry and dynamic mechanical analysis, and chemical interactions in the blends were probed by Fourier‐transform infrared spectroscopy. Amorphous blends were miscible over the entire range of composition, although mixing was most favorable at higher thermoplastic polyimide concentrations. Blending suppressed crystallization, especially of the minor component, but crystallization of both components, however, did occur in most of the blends. While blends quenched from the melt exhibited only a single amorphous phase, melt crystallized blends appeared to possess two amorphous phases with different compositions. Shifts in the vibration frequencies of the carbonyl and imide bonds were inconsistent with the development of strong, specific intermolecular interactions, but may be explained by a disruption of the packing of the two homopolymers by nature of the mixing. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1227–1235, 2004     

Effect of high-performance polymers on crystallization and multiple melting behavior of poly(phenylene sulfide)

The crystallization and multiple melting behavior of poly(phenylene sulfide) (PPS) and its blends with amorphous thermoplastic bisphenol A polysulfone (PSF) and phenolphthalein poly(ether ketone) (PEK-C), crystalline thermoplastic poly(ether ether ketone) (PEEK), and thermosetting bismaleimide (BMI) resin were investigated by a differential scanning calorimeter (DSC). The addition of PSF and PEK-C was found to have no influence on the crystallization temperature (T_c) and heat of crystallization (ΔH_c) of PPS. A significant increase in the value of T_c and the intensity of the T_c peak of PPS was observed and the crystallization of PPS can be accelerated in the presence of the PEEK component. An increase in the T_c of PPS can also be accelerated in the BMI/PPS blend, but was no more significant than that in the PEEK/PPS blend. The T_c of PPS in the PEEK/PPS blends is dependent on the maximum temperature of the heating scans and can be divided into three temperature regions. The addition of a second component has no influence on the formation of a multiple melting peak. The double melting peaks can also be observed when PPS and its blends are crystallized dynamically from the molten state. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 637–644, 1998     

Fine poly(ether ether ketone) powders

The physical form of polymers is often important for carrying out subsequent processing operations. For example, fine powders are desirable for molding and sintering compounds because they consolidate to produce void free components. The objective of this work is to prepare fine polymeric particulates suitable for processing into fiber reinforced polymer matrix composites. Micron size particles of poly(ether ether ketone) (PEEK) were prepared by rapidly quenching solutions of these materials. PEEK pellets were dissolved at temperatures near the PEEK melting point in a mixture of terphenyls and quaterphenyls; then the solution was quenched to a temperature between the T_g and T_m (≈ 225°C) by adding a room temperature eutectic mixture of diphenyl ether and biphenyl. A supersaturated, metastable solution of PEEK resulted, causing rapid nucleation. Fine PEEK particles rapidly crystallized from this solution. The average particle size was measured using transmission electron microscopy, atomic force microscopy, and by light scattering of aqueous suspensions which had been fractionated by centrifugation. The average particle diameter was about 0.6 μm. Three dimensional photomicrographs obtained via atomic force microscopy showed some aggregates in the suspensions. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 1571–1578, 1997     

Synthesis of multi‐block copolymer and its compatibilization to the blends of poly(ether ether ketone) with thermotropic liquid crystalline polymer

A multiblock copolymer (BCP) containing amorphous poly(aryl ether ketone) (PAEK) and thermotropic liquid crystalline polymer (TLCP) segments was synthesized. The chemical structure and properties of BCP were characterized by fourier‐transform infrared spectrometer (FTIR), differential scanning calorimeter (DSC), gel permeation chromatograms (GPC), thermogravimetry analysis, polar light microscope (PLM), and solubility test respectively. BCP can dissolve in chloroform because of soluble PAEK block bonded with TLCP block, which was insoluble. The peak of the original PAEK oligomer was no more present in the GPC traces of the block copolymer. These facts indicated that polymer synthesized should be copolymers of the two components rather than blends. A single T_g at 138.1°C and broad melting endotherm at 315.7°C can be observed. The liquid crystalline texture of BCP showed uniformity in the view after heat treated for 10 min above its T_m under PLM. Ternary blends of poly(ether ether ketone) (PEEK)/TLCP/BCP were prepared by extrusion and characterized by DSC. DSC results showed that the crystallization temperature of PEEK phase in the blends shifted higher with the addition of TLCP. Wide angle X‐ray diffraction investigations indicated that the crystalline structure of PEEK was not disturbed by blending or compatibilizing. Scanning electron microscope and mechanical tests confirmed the compatibilizing effect of BCP. Reduction in dispersed phase TLCP size was observed when 2 phr by weight of compatibilizer was added to the blend. Measurement of the tensile properties showed increased elongation as well as improved modulus and strength to some extent. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Poly(acrylonitrile‐butadiene‐styrene)/Poly(ether ether ketone) Blends: an Attempt Towards a Polymer Reinforced Polymer Composite

Summary: Blends of poly(acrylonitrile‐butadiene‐styrene) (ABS) and poly(ether ether ketone) (PEEK), in which PEEK has been used as a reinforcing medium for the ABS matrix in ratios up to 20 wt.‐% of the blend, were prepared by melt mixing using a laboratory mixer. All the blend compositions were processed at the ABS processing temperature so that the PEEK was dispersed in the ABS matrix without actually melting. Differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) studies revealed that the glass transition temperature (T_g) of the ABS phase in the blend did not show any appreciable change with composition. The dynamic storage modulus measured by DMA was found to be higher for the blend as compared to pure ABS due to reinforcement of the matrix by PEEK. The tensile strength and modulus behavior of these blends were found to follow the curves predicted using models proposed for composite systems having perfect adhesion, which shows the presence of some physical interaction between the blend components. The good tensile properties of the blend have been correlated with the observed morphology. The disperse phase in the blend has been found to be present in extremely small (sub‐micron) dimensions, which not only provides more surface area for possible interactions between the blend components but also result in efficient stress transfer between the matrix and the dispersed phase during the tensile tests. The thermal stability of the blends was investigated using thermogravimetric analysis (TGA). TGA further revealed that the constituents degraded at their respective decomposition temperatures.

SEM micrograph of tensile fractured surface of an ABS/PEEK 90/10 blend.     

The study on poly(ether sulfone) modified cyanate ester resin and epoxy resin cocuring blends

Poly(ether sulfone) terminated with phenolic hydroxyl groups modified cyanate ester resin and epoxy resin cocuring blends were investigated by differential scanning calorimetry, Fourier transform infrared spectroscopy, scanning electron microscopy, rheometry, and mechanical properties measurement. The results suggested that poly (ether sulfone) (PES) could accelerate the polycyclotrimerization reaction of cyanate ester and cocuring processes between cyanate ester and epoxy of modified blends because of the presence of phenolic hydroxyl groups at the end of the PES molecules. It was found that the evolution of the morphologies and complex viscosities of the modified blends sensitive to molecular weight and content of PES, the tensile strength and elongation at break of the modified blends were correlated with the morphologies of modified blends. Moreover, the evolution of complex viscosities of the modified blends also showed an exponential growth at the early stage of phase separation, which demonstrated experimentally that the coarsening processes of droplets of bisphenol‐A dicyanate and diglycidyl ether of bisphenol A and the final morphologies obtained in the blends modified with PES were affected by viscoelastic behavior. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Structure and mechanical properties of blends of poly(ε‐caprolactone) with a poly(amino ether)

Poly(ε‐caprolactone) (PCL)/poly(amino ether) (PAE) blends were obtained by injection molding without any previous extrusion step in an attempt to (i) contribute to the knowledge of the relation between structure and mechanical properties in these type of blends composed of a rubbery and a glassy polymer and (ii) to find out to which extent are the PCL/PAE blends compatible, and therefore whether the biodegradability of PCL can be added as a characteristic of PAE‐based applications. PCL/PAE blends are composed of a crystalline PCL phase, a pure amorphous PCL phase, and a PAE‐rich phase where some PCL is present. The presence of some dissolved and probably unreacted PCL in the PAE‐rich phase led to a low interfacial tension as observed by the small size of the dispersed particles and the large interfacial area. The dependence on composition of both the modulus of elasticity and the yield stress of the blends was parallel to that of the orientation level. The elongation at break showed values similar to those of PAE in PAE‐rich blends, and was slightly synergistic in very rich PCL compositions; this behavior reflects a change in the nature of the matrix, from glassy to rubbery. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Characteristics of poly(ether ether ketone) microporous membranes prepared via thermally induced phase separation (TIPS)

The morphology and bulk properties of microporous membranes based on poly (ether ether ketone) (PEEK) have been investigated as a function of initial casting composition and thermal and mechanical processing history. Membranes were prepared via solid—liquid phase separation of miscible blends of PEEK and polyetherimide (PEI), with subsequent extraction of the PEI diluent. Scanning electron microscopy studies revealed a microporous morphology with two distinct pore size scales corresponding to diluent extraction from interfibrillar and interspherulitic regions, respectively. The membrane structure was sensitive to both initial blend composition and crystallization temperature, with the resulting pore size distribution reflecting the kinetics of phase separation. For membranes prepared with lower initial diluent content or at lower crystallization temperatures, mercury intrusion porosimetry indicated a relatively narrow distribution of fine interfibrillar pores, with an average pore size of approximately 0.04 microns. Membranes prepared at higher diluent content or at higher crystallization temperatures displayed a broad pore distribution, with a sizeable population of coarse, interspherulitic pores (0.1 to 1 μm in size). Uniaxial drawing led to a fibrillated network structure with markedly higher water flux characteristics compared to the as-cast membranes. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 2347–2355, 1997     

Synthesis and properties of thio‐containing poly(ether ether ketone)s

A series of thio‐containing poly(ether ether ketone) (PEESK) polymers was synthesized by the introduction of thio groups from 4,4′ thiodiphenol (TDP) into the poly(ether ether ketone) (PEEK) structure via reaction between the phenol and aromatic fluoride groups. The effect of the thio groups on the properties of the PEESK materials was investigated. Differential scanning calorimetry (DSC) analysis and X‐ray diffraction (XRD) patterns show a depression in the crystallinity of the PEESKs with incorporation of the content of thio groups in the backbones. The crystalline structure was identified as an orthorhombic structure with lattice constants of a = 7.52 Å, b = 5.86 Å and c = 10.24 Å for all crystallizable PEESKs. The crystalline structures of the thio‐containing PEEK polymers were the same as that of the neat PEEK, which means the thio‐containing block in the whole thio‐containing PEEK molecule is almost excluded from the crystalline structure and the crystals are completely formed by ‘non‐thio’ blocks only. Due to the glass transition temperature (T_g) and melting temperature (T_m) depression with increase in the TDP content in the reaction system, the processability of the resultant thio‐containing PEEKs could be effectively improved. Copyright © 2004 Society of Chemical Industry     

Effect of PES on the morphology and properties of proton conducting blends with sulfonated poly(ether ether ketone)

Development of alternate materials to Nafion, based on ionically conducting polymers and their blends is important for the wider applications of proton exchange membrane fuel cells. In this work, blends of sulfonated poly(ether ether ketone) (SPEEK) with poly(ether sulfone) (PES) are investigated. SPEEK with various ion exchange capacity (IEC) was prepared and blended with PES, which is nonionic and hydrophobic in nature. A comparative study of the water uptake, proton conductivity, and thermo‐mechanical characteristics of SPEEK and the blend membranes as a function of the IEC is presented. Addition of PES decreases the water uptake and conductivity of SPEEK. Chemical and thermal stability and mechanical properties of the membrane improve with the addition of PES. The effect of water content on the thermo‐mechanical properties of membranes was also studied. The morphology of blend membranes was studied using SEM to understand the microstructure and miscibility of the components. On the basis of the results, a plausible microstructure of the blends is presented, and is shown to be useful in understanding the variation of different properties with blending. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Thermal properties of melt‐blended poly(ether ether ketone) and poly(ether imide)

The thermal properties of blends of poly(ether ether ketone) (PEEK) and poly(ether imide) (PEI) prepared by screw extrusion were investigated by differential scanning calorimetry. From the thermal analysis of amorphous PEEK–PEI blends which were obtained by quenching in liquid nitrogen, a single glass transition temperature (T_g) and negative excess heat capacities of mixing were observed with the blend composition. These results indicate that there is a favorable interaction between the PEEK and PEI in the blends and that there is miscibility between the two components. From the Lu and Weiss equation and a modified equation from this work, the polymer–polymer interaction parameter (χ₁₂) of the amorphous PEEK–PEI blends was calculated and found to range from −0.058 to −0.196 for the extruded blends with the compositions. The χ₁₂ values calculated from this work appear to be lower than the χ₁₂ values calculated from the Lu and Weiss equation. The χ₁₂ values calculated from the T_g method both ways decreased with increase of the PEI weight fraction. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 733–739, 1999