Compatibilization of PP/PE blends and scraps with Royalene: Mechanical properties,SAXS, and WAXS

PP/PE 93/7 model virgin blends and recycled scraps were compatibilized with Royalene (EPDM/PE 65/35 blend) and mechanically tested. No differences in impact and tensile properties between them were found. However, the tensile-impact strength increased almost twice with 10%-compatibilized sample in comparison with uncompatibilized ones. The yield stress of blends containing 10% Royalene decreased to 75–80% of the original value. This effect is in agreement with microhardness measurements; the increase in the compatibilizer content causes softening of the blend. The elongation at break and elongation at yield do not depend on the compatibilizer concentration. The compatibilizer does not influence the degree of crystallinity (WAXS data) of the blends either. Vickers microhardness is in good agreement with Tabor's relationship. The differences between long periods of HDPE in Royalene and LDPE in PP/PE blends (SAXS) proved PE/EPDM interaction. The interaction plays a key role in the toughening of PP/PE blends. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

ABS/HIPS blends obtained from WEEE: Influence of processing conditions and composition

The recycling of acrylonitrile–butadiene–styrene (ABS) and high‐impact polystyrene (HIPS) from postconsumer electronic equipment housing was investigated. A preliminary study of shot size and particle size effects on the mechanical properties of ABS/HIPS (50/50) blends obtained directly via injection molding was conducted. Injection‐molded specimens of ABS/HIPS blends, obtained at different compositions with or without previous extrusion, were subjected to mechanical, thermal, and morphological testing. Preliminary studies showed that a smaller particle size resulted in higher tensile and impact strength, regardless of the shot size used during injection molding. ABS/HIPS blends obtained using previous extrusion presented a slight increase in Young's modulus and a decrease in elongation at break and impact strength. The increase in glass‐transition temperature related to the Polybutadiene (PB) phases of these blends indicated a possible increase in crosslinking structures during extrusion. In addition, these blends showed a coarse and heterogeneous morphology, suggesting that ABS did not completely mix with HIPS. Compared to processing conditions, the blend composition appeared to have a much stronger effect on the mechanical properties. The results obtained suggest the possibility of obtaining ABS/HIPS blends directly via injection molding as long as small ground particles are used. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43831.     

PP/PE blends. IV. Characterization and compatibilization of blends of postconsumer resin with virgin PP and HDPE

The mechanical properties of blends of isotactic polypropylene and high-density polyethylene with a postconsumer resin (recycled dairy containers) were investigated over the entire composition range. Modification of these blends with an ethylene/propylene/diene copolymer or an ethylene/vinyl acetate copolymer was also investigated. Isotactic polypropylene/postconsumer resin blends have satisfactory impact and tensile properties at postconsumer resin contents of less than 50% for certain applications. At higher postconsumer resin contents, the tensile properties were adversely affected. The impact properties remained satisfactory. Addition of an ethylene/propylene/diene copolymer improved the mechanical properties of these blends to levels equal to or greater than those for neat isotactic polypropylene. Ethylene/vinyl acetate copolymers were also able to improve the mechanical properties, but not as efficiently as did the ethylene/propylene/diene copolymer. Blends of high-density polyethylene and a postconsumer resin had poor impact and tensile properties. Although the ethylene/propylene/diene copolymer and ethylene/vinyl acetate copolymers were able to improve these properties, the improvement was insufficient for general recycling, except at lower (≤25%) postconsumer resin contents. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 2081–2095, 1998     

Partial replacement of EPR by GTR in highly flowable PP/EPR blends: Effects on morphology and mechanical properties

This research analyzes the effect of ground tire rubber (GTR) and a novel metallocene‐based ethylene–propylene copolymer (EPR), with high propylene content, on the morphology and mechanical behavior of ternary polymer blends based on a highly flowable polypropylene homopolymer (PP). The PP/EPR blends morphology, with very small domains of EPR dispersed in the PP matrix, indicates a good compatibility among these materials, which leads to a significant improvement on elongation at break and impact strength. The incorporation of EPR on the rubber phase of thermoplastic elastomeric blends (TPE) based on GTR and PP (TPE^GTR) has a positive effect on their mechanical performance, attributed to the toughness enhancement of the PP matrix and to the establishment of shell‐core morphology between the rubber phases. The mechanical properties of the ternary blends reveal that TPE^GTR blends allow the upcycling of this GTR material by injection molding technologies. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42011.     

PS/EPDM blends prepared by in situ polymerization of styrene

PS/EPDM blends formed by in situ polymerization of styrene in the presence of EPDM were prepared. EPDM has excellent resistance to factors such as weather, ozone and oxidation and it could be a good alternative for substituting polybutadiene‐based rubbers in PS toughening. The PS/EPDM blends present two phases, an EPDM elastomeric phase dispersed into a rigid matrix. The blends show higher thermal stability than polystyrene homopolymer due to the stabilizing effect of EPDM incorporation. The mechanical properties of in situ polymerized PS/EPDM blends with different compositions were evaluated before and after accelerated photoaging and compared with the properties of HIPS submitted to the same aging conditions. The blend containing 17 wt % of EPDM presents an increase in the impact resistance of 210% in comparison with the value of PS. Although the initial mechanical properties of HIPS are superior, a pronounced drop was observed after an exposure time. For example, after the aging period, all PS/EPDM blends showed higher strain at break than HIPS. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Structure and properties of polypropylene/high‐density polyethylene blends by solid equal channel angular extrusion

The solid equal channel angular extrusion (ECAE) process on polypropylene (PP)/high‐density polyethylene (HDPE) blends was carried out. Scanning electron microscopy (SEM) was used to observe the sample structures. Results showed that ECAE process could make PP/HDPE blends to produce orientation structure. Impact performance of ECAE‐PP/HDPE samples after ECAE process improved remarkably, especially for ECAE‐PP/HDPE (90/10)‐O whose impact strength reached 91.91 kJ/m², 18.1 times higher than that of pure PP and 11.2 times higher than that of PP/HDPE (90/10). The mechanism of enhancing between HDPE and PP was discussed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39759.     

Phase morphology of PP/COC blends

Phase morphology of polymer blends PP/COC, where PP is polypropylene and COC is a copolymer of ethene and norbornene, was characterized by means of scanning electron microscopy (SEM) and scanning transmission electron microscopy (STEM). PP/COC blends were prepared by injection molding and their morphology was studied for six different compositions (90/10, 80/20, 70/30, 60/40, 50/50, and 25/75 wt %). The intention was to improve PP properties by forming COC cocontinuous phase, which should impart to the PP matrix higher stiffness, yield stress, and barrier properties. Surprisingly enough, all studied blends were found to have fibrillar morphology. In the 90/10, 80/20, and 70/30 blends, the PP matrix contained fibers of COC, whose average diameter increased with increasing COC fraction. In the 60/40 blend, the COC component formed in the PP matrix both fibers and larger elongated entities with PP fibers inside. The 50/50 blend was formed by COC cocontinuous phase with PP fibers and PP cocontinuous phase with COC fibers. In the 25/75 blend, PP fibers were embedded in the COC matrix. In all blends, the fibers had an aspect ratio at least 20, were oriented in the injection direction, and acted as a reinforcing component, which was proven by stress–strain and creep measurements. According to the available literature, the fibrous morphology formed spontaneously in PP/COC is not common in polymer blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 253–259, 2004     

Healing phenomenon adapted to understand the miscibility of polymer blends: An approach based on the deformation mechanism

Following many years of studies on polyethylene blends, several indirect classical experimental methods (DSC, XRD, DMA, cryogen fracture surface using SEM, and Rheological Test in Oscillatory Flow) have been used to evaluate the compatibility between polyethylene blends. Here a study of a high-density polyethylene (HDPE)—ultrahigh molecular weight polyethylene (UHMWPE) system, which evidences that the compatibility of mixtures using these experimental methods does not assure good mechanical performance of the blends. In addition, the potential that these blends can perform mechanically may be overestimated. Based on the theory of healing at a polymer-polymer interface, it was shown that the maximum mechanical performance of the HDPE-UHMWPE blend can be obtained for long time molecular diffusion when the mixtures equilibrium (maximum mixing degree) at the HDPE-UHMWPE interphase is achieved. The degree of mixture at the HDPE-UHMWPE interphase was assessed indirectly by the deformation mechanism that each phase and the interphase plays during the tensile test (at solid state). The advances reported in this paper can contribute to understanding the mechanical performance of different systems formed by compatible polyethylene blends.     

Influence of processing conditions on the morphological and mechanical properties of compatibilized PP/LCP blends

The main aim of this work is to study the influence of the application of different processing conditions on the morphological and mechanical properties of thermoplastic/LCP blends, in which the viscosity ratios are inferior to unity and decrease with increasing temperature. The way the microstructure evolves along the extruder determines the final morphology and thus, the mechanical performance of the systems. In the present case, the mechanical properties are related with the degree of fibrillation in the final composites. The best degree of fibrillation was obtained for low screw speeds and temperatures and for intermediate outputs. The use of high screw speeds and processing temperatures results in a decrease of the viscosity ratio, in the former case via an increase in the viscous dissipation, at the regions of higher shear rates (kneading‐elements). The application of a lower processing temperature is advantageous for deformation, break‐up, and fibrillar formation because of the higher viscosity ratios and higher shear stresses involved. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Microcellular foaming of PE/PP blends

Three different polyethylene/polypropylene (PE/PP) blends were microcellular foamed and their crystallinities and melt strengths were investigated. The relationship between crystallinity, melt strength, and cellular structure was studied. Experimental results showed that the three blends had similar variation patterns in respect of crystallinity, melt strength, and cellular structure, and these variation patterns were correlative for each blend. For all blends, the melt strength and PP melting point initially heightened and then lowered, the PP crystallinity first decreased, and then increased as the PE content increased. At PE content of 30%, the melt strength and PP melting point were highest and the PP crystallinity was least. The blend with lower PP crystallinity and higher melt strength had better cellular structure and broader microcellular foaming temperature range. So, three blends had best cellular structure at PE content of 30%. Furthermore, when compared with PE/homopolymer (hPP) blend, the PE/copolymer PP (cPP) blend had higher melt strength, better cellular structure, and wider microcellular foaming temperature range, so it was more suited to be microcellular foamed. Whereas LDPE/cPP blend had the broadest microcellular foaming temperature range because of its highest melt strength within three blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 4149–4159, 2007     

Compatibilization effects of styrenic/rubber block copolymers in polypropylene/polystyrene blends

Compatibilizing effects of styrene/rubber block copolymers poly(styrene‐b‐butadiene‐b‐styrene) (SBS), poly(styrene‐b‐ethylene‐co‐propylene) (SEP), and two types of poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) (SEBS), which differ in their molecular weights on morphology and selected mechanical properties of immiscible polypropylene/polystyrene (PP/PS) 70/30 blend were investigated. Three different concentrations of styrene/rubber block copolymers were used (2.5, 5, and 10 wt %). Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to examine the phase morphology of blends. The SEM analysis revealed that the size of the dispersed particles decreases as the content of the compatibilizer increases. Reduction of the dispersed particles sizes of blends compatibilized with SEP, SBS, and low‐molecular weight SEBS agrees well with the theoretical predictions based on interaction energy densities determined by the binary interaction model of Paul and Barlow. The SEM analysis confirmed improved interfacial adhesion between matrix and dispersed phase. The TEM micrographs showed that SBS, SEP, and low‐molecular weight SEBS enveloped and joined pure PS particles into complex dispersed aggregates. Bimodal particle size distribution was observed in the case of SEP and low‐molecular weight SEBS addition. Notched impact strength (a_k), elongation at yield (ε_y), and Young's modulus (E) were measured as a function of weight percent of different types of styrene/rubber block copolymers. The a_k and ε_y were improved whereas E gradually decreased with increasing amount of the compatibilizer. The a_k was improved significantly by the addition of SEP. It was found that the compatibilizing efficiency of block copolymer used is strongly dependent on the chemical structure of rubber block, molecular weight of block copolymer molecule, and its concentration. The SEP diblock copolymer proved to be a superior compatibilizer over SBS and SEBS triblock copolymers. Low‐molecular weight SEBS appeared to be a more efficient compatibilizer in PP/PS blend than high‐molecular weight SEBS. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 291–307, 1999     

Optimization of PE/Binder/PA extrusion blow‐molded films. I. Heat sealing ability improvement using PE/EVA blends

The optimization of three‐layer films (PE/binder/PA) manufactured by extrusion blow molding presents significant industrial challenges. The main issue consists in combining use properties (e.g., impermeability to water steam and oxygen, welding properties) with high mechanical, optical, and adhesion performances, while maintaining cost‐effectiveness. This article shows that the introduction of EVA in the PE layer improves the heat sealing ability and optical properties without degradation of the mechanical and adhesion performances. In the most favorable case, this modification leads to a 40% reduction of the heat sealing time, the other performances remaining either identical or higher. This leads to cost reduction of this manufacturing step while improving the flexibility of the process (wider process temperature window). The properties modifications observed can be explained by microstructure modifications (crystallinity, orientation, and molecular mobility). © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 974–985, 2006     

Compatibilization of polypropylene/polystyrene blends with poly(styrene-b-butadiene-b-styrene) block copolymer

The compatibilizing effect of the triblock copolymer poly(styrene-b-butadiene-b-styrene) (SBS) on the morphology and mechanical properties of immiscible polypropylene/polystyrene (PP/PS) blends were studied. Blends with three different weight ratios of PP and PS were prepared and three different concentrations of SBS were used for investigations of its compatibilizing effects. Scanning electron microscopy (SEM) showed that SBS reduced the diameter of the PS-dispersed particles as well as improved the adhesion between the matrix and the dispersed phase. Transmission electron microscopy (TEM) revealed that in the PP matrix dispersed particles were complex “honeycomblike” aggregates of PS particles enveloped and joined together with the SBS compatibilizer. Wide-angle X-ray diffraction (WAXD) analysis showed that the degree of crystallinity of PP/PS/SBS slightly exceeded the values given by the addition rule. At the same time, addition of SBS to pure PP and to PP/PS blends changed the orientation parameters A₁₁₀ and C significantly, indicating an obvious SBS influence on the crystallization process in the PP matrix. SBS interactions with PP and PS influenced the mechanical properties of the compatibilized PP/PS/SBS blends. Addition of SBS decreased the yield stress and the Young's modulus and improved the elongation at yield as well as the notched impact strength in comparison to the binary PP/PS blends. Some theoretical models for the determination of the Young's modulus of binary PP/PS blends were used for comparison with the experimental results. The experimental line was closest to the series model line. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 69: 2625–2639, 1998     

Improvement of mechanical properties for PP/PS blends by in situ compatibilization

The effect of the in situ compatibilization on the mechanical properties of PP/PS blends was investigated. The application of Friedel-Crafts alkylation reaction to the PP/PS-blend compatibilization was assessed. Styrene/AlCl₃ was used as catalyst system. The graft copolymer (PP-g-PS) formed at the interphase showed relatively high emulsifying strength. Scission reactions, occurring in parallel with grafting, were verified for PP and PS at high catalyst concentration, but no crosslinking reactions were detected. Tensile tests were performed on dog-bone specimens of the blends. Both elongation at break and toughness increased with catalyst concentration. At 0.7% AlCl₃, a maximum was reached, which amounted to five times the value of the property for the uncompatibilized blend. At higher catalyst concentrations these properties decreased along with the PP molecular weight due to chain-scission reactions. On the other hand, the tensile strength did not change with the catalyst concentration. The in situ compatibilized blends showed considerable improvement in mechanical properties, but were adversely affected by chain scissions at high catalyst contents.     

Effect of clay type and polymer matrix on microstructure and tensile properties of PLA/LLDPE/clay nanocomposites

Polylactide (PLA)/linear low‐density polyethylene (LLDPE), (PLA/LLDPE), blends and nanocomposites were prepared by melt mixing process with a view to fine tune the properties. Two different commercial‐grade nanoclays, Cloisite® 30B (30B) and Cloisite® 15A (15A) were used. A terpolymer of ethylene, butylacrylate (BA) and glycidylmethacrylate (GMA) was used as a reactive compatibilizer. The influence of type of clay on the morphology and mechanical properties of two PLA‐rich and LLDPE‐rich blend systems was studied. Morphological analysis using X‐ray diffraction, transmission electron microscopy, and scanning electron microscopy revealed that the organoclay layers were dispersed largely at the interface of PLA/LLDPE. Decreasing the PLA content changed the morphology from droplet‐in matrix to coarse co‐continuous. In comparison with 30B, due to less affinity of 15A towards compatibilizer and PLA phase, the reduction of the size of dispersed phase was less than that of the equivalent 30B composites. The mechanical results demonstrated that the composites containing both types of organoclay exhibited higher modulus but lower elongation and tensile strength as compared to the neat blends. The injection molded nanocomposites were shown to have the sequential fracture behavior during tensile test. The tensile testing results on the neat blends and nanocomposites showed significant increase in elongation at break and decrease in the modulus as compared with the neat PLA. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 749‐758, 2013     

Polypropylene/polyethylene blends as models for high‐impact propylene‐ethylene copolymers,part 2: Relation between composition and mechanical performance

The relation between composition and mechanical performance of a series of binary polyolefin blends was studied in this article. A fractionation of these model compounds with temperature rising elution fractionation (TREF) was applied to study the possibility to fractionate industrially relevant heterophasic polyolefin systems. The separation quality according to molecular structures or chemical composition was found to be good for most of the systems, but especially the separation of ethylene‐propylene random copolymer and high density polyethylene by TREF turned out to be difficult if not impossible. An extensive mechanical characterisation including the determination of brittle‐to‐ductile transition curves showed significant effects of modifier type and amount. Toughness effects can be related primarily to the modulus differences between modifier and matrix. Compatibility and particle size only have a secondary influence, but must be considered for a detailed interpretation of the mechanics of the investigated systems. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

PET/PA nanocomposite blends with improved gas barrier properties: Effect of processing conditions

The aim of this research is to develop nanocomposite polyethylene terephthalate‐polyamide blends (PET/MXD6 blends) with low oxygen permeability. Particular attention has been paid to the relation between barrier properties and the processing route adopted and therefore four different strategies were considered. Mechanical characterization shows that clay may effectively act as reinforcing filler in PET/MXD6 blends. Morphological characterization shows the strong effect of the processing strategy on clay dispersion and its distribution between the PET and polyamide phases. Barrier properties of PET/MXD6 nanocomposite blends are enhanced with respect to neat PET polymer as well as PET/MXD6 blends. The significant effect of processing techniques on barrier properties is also revealed. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Effect of reactive compatibilisation on the phase morphology and tensile properties of PA12/PP blends

Both uncompatibilized and compatibilized blends based on polyamide 12 (PA12) and isotactic polypropylene (PP) were prepared in a Brabender Plastograph®. The compatibiliser used was maleic anhydride functionalized polypropylene (PP‐g‐MA). Phase morphology of the blends was inspected in scanning electron microscope (SEM) on cryogenically fractured etched surfaces of the specimens. PA12/PP blends possessed a nonuniform and unstable morphology owing to the incompatibility between their constituents. Addition of compatibiliser improved the interfacial characteristics of the blends by retarding the rate of coalescence. So, the phase morphology became more fine, uniform, and stable. Tensile properties of both uncompatibilized and compatibilized blends were measured as a function of blend composition and compatibiliser concentration. Uncompatibilized blends displayed inferior mechanical properties to compatibilized ones; especially for those containing 40–60 wt % of PP. Reactive compatibilisation of blends was found to be efficient and improved the tensile strength of the blends considerably. Addition of PP‐g‐MA improved the interfacial adhesion, decreased the interfacial tension, and thereby, enhanced the tensile strength by 85%. Finally, various models were adopted to describe the tensile strength of the blends. The experimental data exhibited a reasonably good fit with Nielsen's first power law model. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Compatibilization of regenerated low density polyethylene/poly(vinyl chloride) blends

The aim of this work is to study the valorization of regenerated low density polyethylene (rLDPE) by blending with PVC in the presence of chlorinated polyethylene (CPE) as compatibilizer. For this purpose, four rLDPE samples coming from neat or dirty wastes were used. They were obtained after milling, washing, and extrusion in a conventional recycling plant. They were first characterized in terms of physicochemical (density, melt flow index, water absorption, and level of oxidation by Fourier transform infrared spectroscopy) and mechanical (tensile and shore D hardness) properties. The effect of the ratio of PVC on these physical and mechanical properties was then investigated. These binary blends exhibited lower properties than those of the separated polymers. The addition of CPE to the binary blend with weight proportion of 50/50 leads to a substantial improvement of the considered properties which is due to a better interfacial adhesion between rLDPE and PVC as evidenced by the analysis of the morphology of the blends by scanning electron microscopy. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008