三正丁胺络合萃取精馏分离醋酸和水

A new separation method, reactive extractive distillation, was put forward for separating water and acetic acid. The separation mechanism was analyzed through infrared spectra technique. Isobaric vapor-liquid equilibrium (VLE) data at 101.33 kPa for the binary or ternary systems consisting of water, acetic acid and tributylamine were measured. The activity coefficients were correlated by using Wilson, NRTL, and UNIQUAC Equations.The VLE experiment showed that tributylamine could enhance the relative volatility of water to acetic acid. An extractive distillation experiment was carried out and proved that tributylamine was a good extractive solvent.     

288.15K-308.15K(Poloxamerl88+乙醇/丙酮+水)三元体系的密度和黏度

The densities and viscosities of ternary systems(Poloxamer 188+ethanol/acetone+water)were meas- ured at 288.15,293.15,298.15,303.15,308.15 K and atmospheric pressure for different mass fractions of Poloxamer 188(0 to 0.02)in aqueous solution and different solvent volume fractions of ethanol/acetone(0 to 0.3)in Poloxamer 188 aqueous solution.The densities were measured by a pycnometer,while the viscosities were measured using two Ubbelohde capillary viscometers.The correlations of density and viscosity of these ternary systems are obtained by fitting the experimental data at different temperatures,mass fractions and volume fractions.     

对二甲苯和醋酸二元液体混合物在不同温度下的超额摩尔体积、粘度和热容

Experimental densities, viscosities and heat capacities at different temperatures were presented over the entire range of mole fraction for the binary mixture of p-xylene and acetic acid. Density values were used in the determination of excess molar volumes, VE. At the same time, the excess viscosity and excess molar heat capacities were calculated. The values of V^E, η^E and cE/p were fitted to the Redlich-Kister equation. Good agreements were observed. The excess molar volumes are positive with a large maximum value located in the central concentrationrange. The excess viscosity has an opposite trend to the excess molar volume V^E. η^E values are negative over the entire range of the mixture. The cure of dependence of c E/p on concentration has a special shape. The molecularinteraction between v-xvlene and acetic acid is discussed.     

立方型状态方程结合Eyring理论在液体混合物黏度计算中的应用

Cubic equations of state (EOS) have been combined with the absolute rate theory of Eyring to calculate viscosities of liquid mixtures. A modified Huron Vidal gE-mixing rule is employed in the calculation and in comparison with the van Laar and the Redlich-Kister-type mixing rule. The EOS method gives an accurate correlation of liquid viscosities with an overall average deviation less than 1% for 67 binary systems including aqueous solutions. It is also successful in extrapolating viscosity data over a certain temperature range using parameters obtained from the isotherm at a given temperature and in predicting viscosities of ternary solutions from binary parameters for either polar or associated systems.     

醋酸脱水过程中对二甲苯+(醋酸,醋酸甲酯,醋酸正丙酯)和醋酸甲酯+醋酸正丙酯的二元汽液相平衡(英文)

The vapor-liquid equilibrium data of four binary systems (acetic acid +p-xylene, methyl acetate +n-propyl acetate, n-propyl acetate +p-xylene and methyl acetate +p-xylene) are measured at 101.33 kPa with Ellis equilibrium still, and then both the NRTL and UNIQUAC models are used in combination with the HOC model for correlating and estimating the vapor-liquid equilibrium of these four binary systems. The estimated binary VLE results using correlated parameters agree well with the measured data except the methyl acetate +p-xylene system which easily causes bumping and liquid rushing out of the sampling tap due to their dramatically different boiling points. The correlation results by NRTL and UNIQUAC models have little difference on the average absolute deviations of temperature and composition of vapor phase, and the results by NRTL model are slightly better than those by UNIQUAC model except for the methyl acetate +n-propyl acetate system, for which the latter gives more accurate correlations.     

离子液体[BMIM][DBP]+水+甲醇/乙醇三元工质溶液蒸汽压的测量和预测(英文)

The ionic liquid, 1-butyl-3-methylimidazolium dibutylphosphate ([BMIM][DBP]) was prepared and the vapor pressures of three set of binary solutions H2O(1)/CH3OH(1)/C2H5OH(1) + [BMIM][DBP](2) were measured at different temperature and in the ILs mole fraction range from 0.1 to 0.6 with a static equilibrium apparatus. The measured vapor pressures were correlated with Non-Random Two Liquid (NRTL) activity coefficient model and the average relative deviations (ARD) between experimental and correlated vapor pressures for these binary solutions were 3.19%, 2.42% and 2.95%, respectively. Then, the vapor pressures of two set of ternary solutions H2O(1) + CH3OH(2)/C2H5OH(2) + [BMIM][DBP](3) were measured with an inclined boiling apparatus and further predicted with NRTL activity coefficient model based on the binary interaction parameters coming from fitting the vapor pressures of the binary solutions. The results indicated that the ternary solutions containing [BMIM][DBP] were shown a strong negative deviation from Raoult’s Law when the mole fraction of [BMIM][DBP] was larger than 0.2, which meant that ternary solutions could absorb the refrigerant vapors at the same or below solution temperature. Meanwhile, the average relative deviations between experimental and predicted vapor pressures for ternary solutions were 2.92% and 3.06%, respectively. Consequently, the NRTL active coefficient model used for non-electrolyte solutions was still valid for predicting vapor-liquid equilibrium of binary or ternary solutions containing ILs.     

Salt effect on the liquid–liquid equilibrium of the ternary (water + phenol + methyl isobutyl ketone) system: Experimental data and correlation

The effects of NaCl, KCl and Na_2SO_4 on the liquid–liquid equilibrium(LLE) data for the ternary system, water+ phenol + methyl isobutyl ketone, were determined at 0.101 MPa and 333.15 K and 343.15 K.The nonrandom two-liquid(NRTL) model was used to correlate the experimental data and to yield corresponding binary interaction parameters for these salt containing systems.The Hand and Othmer–Tobias equations were used to confirm the dependability of the determined LLE data in this work.Distribution coefficient and selectivity were used to evaluate the extraction performance of methyl isobutyl ketone with the existence of salt.The magnitude of salt effect on the water + phenol + methyl isobutyl ketone(MIBK) system is in the following order: Na_2SO_4NaClKCl.     

Densities and Viscosities of 1-butyl-3-methylimidazolium Hexafluorophosphate [bmim][PF6] ＋ CO2 Binary System： Determination and Correlation

A gas-dissolving device was designed and connected to the falling-body viscometer, which was used to determine the viscosities of liquids in our lab before. The equipment can be used to determine the gas composition, the densities and viscosities of the solution at the same time. The densities and viscosities of [bmim][PF6] ＋ CO2 binary system were determined in the temperature range of 313.2 to 413.2 K and pressure range of 5.0 to 25.0 MPa by the equipment. Then the viscosities of [bmim][PF6] ＋ CO2 binary system at constant temperature, constant pressure, and different temperature and pressure were correlated, respectively. For the correlation at different tempera- ture and different t3ressure for different concentration mixtures the average relative deviation ARD is 0.037.     

Excess Molar Volume, Viscosity and Heat Capacity for the Binary Mixture of p-Xylene and Acetic Acid at Different Temperatures

Experimental densities, viscosities and heat capacities at different temperatures were presented over the entire range of mole fraction for the binary mixture of p-xylene and acetic acid. Density values were used in the determination of excess molar volumes, VE. At the same time, the excess viscosity and excess molar heat capacities were calculated. The values of VE, ηE and cpE were fitted to the Redlich-Kister equation. Good agreements were observed. The excess molar volumes are positive with a large maximum value located in the central concentration range. The excess viscosity has an opposite trend to the excess molar volume VE. ηE values are negative over the entire range of the mixture. The cure of dependence of cpE on concentration has a special shape. The molecular interaction between p-xylene and acetic acid is discussed.     

甲基二氯硅烷-甲基乙烯基二氯硅烷-甲苯三元体系等压汽液平衡

Vapor-liquid euilibrium (VLE) for a ternary system of Methyldichlorosilane methylvinyldichlorosilane toluene and constituent binary systems were measured at 101.3kPa using a new type of magnetical pump-ebulliometer,The equilibrium conpositions of the vapor phase of binary systems were calculated indirectly from the total pressure-temperature-liquid composition(pTx).The experimental data were correlated with the Wilson and NRTL(non-random two liquid )equations.The parameters of the Wilson moldel were employed to predict the ternary VLE data .The calculated boiling points were in good agreement with the experimental ones.     

Liquid-liquid equilibria of the system water + acetic acid + methyl propyl ketone

This article reports equilibrium data for the binary liquid-liquid system water + methyl propyl ketone at temperatures in the range 20-55°C, together with solubilities and equilibrium compositions of the ternary system water + acetic acid + methyl propyl ketone at 25, 35, 45 and 55°C. NRTL and UNIQUAC equations have been fitted to the experimental data for the ternary system, which are likewise compared with the values predicted by the group contribution method UNIFAC.     

水-乙酸-乙酸戊酯体系的等压汽液平衡

用改进的Rose釜测定了水-乙酸、乙酸-乙酸戊酯、水-乙酸-乙酸戊酯在101.33 kPa下的等压汽液平衡数据.考虑了乙酸在汽相中的缔合效应,用维里方程和Hayden-O’connell关联式修正了汽相的非理想性,用非线性最小二乘法关联了水-乙酸和乙酸-乙酸戊酯体系的汽液平衡数据,得出了NRTL和UNIQUAC方程的模型参数.用NRTL模型参数预测了三元汽液平衡数据,计算值与实验值吻合良好.     

Liquid+liquid equilibria of ternary water+carboxylic acid+solvent systems at 288.15 K

The experimental liquid-liquid equilibrium (LLE) data for six ternary systems containing (chloroform+propionic acid+water), (chloroform+acetic acid+water), (diethyl ether+propionic acid+water), (diethyl ether+acetic acid+water), (trichloroethylene+propionic acid+water) and (trichloroethylene+acetic acid+water) were measured at 288.15 K and at atmospheric pressure. An accurate and simple titration method was used for determining of the concentration of carboxylic acid in the both liquid phases at equilibrium. The reliability of the experimental tie-line data was confirmed by using the Othmer-Tobias correlation. The distribution coefficients and selectivity factors were presented to evaluate the efficiency of the solvents for extraction of carboxylic acid from water. The results show that chloroform and diethyl ether are satisfactory solvents for extraction of carboxylic acids from water. Trichloroethylene separates propionic acid from water; however, it cannot be used as a solvent for separation of acetic acid.     

对苯二甲酸和对羧基苯甲醛在醋酸水溶液中的溶解度

测定了420-505K温度范围内,对苯二甲酸和对羧基苯甲醛在醋酸水溶液中溶解度。在70%-100%醋酸水溶液中,70%醋酸使对苯二甲酸的溶解度对温度最敏感,随着醋酸浓度增加,对苯二甲酸的溶解度减少。当温度低于470K时,对苯二甲酸在水中的溶解性低于醋酸中的溶解度;温度高于470K时,对苯二甲酸在水中的溶解性对温度敏感明显提高。40%醋酸使对羧基苯甲醛的溶解度对温度最敏感, 随着醋酸浓度增加, 对羧基苯甲醛的溶解度增加。实验数据用修正的Apelblat方程进行了对苯二甲酸和对羧基苯甲醛在醋酸水溶液中溶解度关联,计算与实验值吻合良好。     

On the predictive capabilities of CPA for applications in the chemical industry: Multicomponent mixtures containing methyl-methacrylate,dimethyl-ether or acetic acid

The predictive performance of the CPA (Cubic-Plus-Association) equation of state for applications relevant to the chemical industry is illustrated in this work. Three such applications inspired by industrial requests/interest are illustrated here, all of which involve aqueous multicomponent mixtures exhibiting vapor–liquid (VLE) and/or liquid–liquid (LLE) equilibrium. The first two cases include mixtures of methyl-methacrylate with acetone or methanol and dimethyl-ether with ethanol, respectively. In these two cases, the classical form of CPA is used. The third case involves aqueous mixtures with acetic acid, esters, ethers and alcohols, and in this case for water–acetic acid the CPA-Huron Vidal (CPA-HV) version of the model is used. For the latter binary mixture, new CPA-HV binary parameter sets are estimated using, among others, data for activity coefficients at infinite dilutions. The modeling approach is similar in all three cases, i.e. the binary parameters are solely fitted to binary data and thus all multicomponent calculations are considered predictions.It is shown that CPA correlations for binary systems are excellent in all cases using temperature independent parameters except for the acetic acid–water system for which different parameter sets at different temperatures can be recommended. Even with the use of CPA-HV mixing rules, modeling of the acetic acid–water system with few interaction parameters remains a challenging task. Excellent simultaneous VLE and LLE correlation is obtained for complex systems such as aqueous mixtures with ethers and esters. The multicomponent results are, with a few exceptions, very satisfactory, especially for the vapor–liquid equilibrium cases. For the demanding aqueous acetic acid–water containing systems, one parameter set is recommended at the end for modeling ternary or multicomponent mixtures containing acetic acid and water.     

Experimental Measurements and Correlations Isobaric Vapor-Liquid Equilibria for Water + Acetic Acid + Sec-butyl Acetate at 101.3 kPa

Isobaric vapor-liquid equilibrium(VLE) data for acetic acid+sec-butyl acetate and water+acetic acid+sec-butyl acetate systems were determined at 101.3 kPa using a modified Rose type. The nonideality of the vapor phase caused by the association of the acetic acid was corrected by the chemical theory and Hayden-O’Connell method. Thermodynamic consistency was tested for the binary VLE data. The experimental data were correlated successfully with the Non-Random Two Liquids (NRTL) model. The Root Mean Square Deviation (RMSD) of the ternary system was 0.0038. The saturation vapor pressure of sec-butyl acetate at 329 to 385 K was measured by means of two connected equilibrium cells. The vapor pressures of water and sec-butyl acetate were correlated with the Antoine equation. The binary interaction parameters and the ternary VLE data were obtained from this work.     

水＋醋酸＋甲基叔丁醚三元体系汽液平衡数据的实验测定及数学模拟

用改进的Rose釜测定了常压下H2O＋HAc＋甲基叔丁醚三元体系部分汽液平衡数据,借助实验数据,利用AspenPlus软件对该三元体系NRTL和UNIQUAC方程的模型参数进行了回归。回归结果反过来用于汽液平衡的数学模拟,结果表明实验数据与模拟结果很吻合,该结果可以为相关研究及工业设计提供帮助。     

醋酸脱轻塔汽液平衡模拟计算

介绍了醋酸脱轻塔汽液平衡计算,通过醋酸体系的二元汽液平衡数据和三元液液平衡数据,回归出醋酸体系的主要二元交互作用参数,用NRTL有序双液方程与Hayden-O′Connell联立方程对非理想缔合体系的汽(液)液平衡的模拟计算,计算出醋酸精馏体系的汽液平衡与液液平衡、焓差和密度,理论模拟出醋酸脱轻塔各塔盘的流量、温度和压力与实际醋酸生产非常接近,其精度完全可满足醋酸生产的要求,对醋酸的生产具有重要的指导和借鉴意义。     

强缔合体系醋酸-水溶液密度和粘度测定及关联

测定了醋酸水二元体系常压下在298.15—363.15K时的密度和粘度数据,由密度数据计算出超额体积VE的值,并用Redlich Kister方程进行了回归;同时对粘度的数据也按超额性质的方法进行了处理,求出了不同温度不同组成下的ηE值。数据处理过程中发现,ηE/(x1x2)随组成没有变化,在不同温度下为一常数,根据这一特殊现象,建立了由纯物质的粘度数据来计算醋酸水体系在任意温度和组成下的粘度数据,并把所得粘度的计算值和实验值进行比较,120个数据点的平均相对误差为1.1%,结果比较满意。     

N-甲基乙酰胺用于萃取精馏乙酸脱水过程机理

以N-甲基乙酰胺（NMA）作溶剂,用理论计算方法对萃取精馏醋酸脱水过程的作用机理进行研究。NMA与水\醋酸之间都有氢键形成,经计算得到NMA-醋酸复合物的稳定化能在-32.4~-44.3kJ/mol之间,且平面构型的NMA-醋酸复合物稳定能较高,而NMA与单分子水的稳定化能仅为-16.0kJ/mol。这说明NMA对醋酸具有选择性结合能力,使得醋酸不易挥发到汽相中去;这与VLE实验结果相一致,加入NMA可将水对醋酸的相对挥发度提高至3.0~4.0。用自然键轨道(NBO)分析表明,以上两种复合物形成过程中均伴随着电荷转移现象,整体上醋酸分子作为电荷受体而存在。