Dynamic Fracture Characterization of Al2O3 and SiCw/Al2O3

The dynamic stress intensity factors, which were determined with newly developed bar impact facilities and a new data reduction procedure, for an Al₂O₃ ceramic and 29 vol% SiC_w/Al₂O₃ composite were virtually identical, thus indicating that the short SiC whiskers were ineffective under dynamic fracture. SEM studies revealed five distinct fracture morphologies with increased percentage area of transgranular fracture in both materials with rapid crack propagation. Also, the high dynamic stress intensity factor caused multiple microscopic crack planes to form and then join as the crack advanced.     

Characterization of Freeze-Dried Al2O3 and Fe2O3

Oxide crystallite formation and growth from freeze-dried sulfates were studied for the representative materials Al₂O₃ and Fe₂O₃. Transmission and scanning electron micrographs showed the formation and growth of chainlike aggregates of crystallites. Aggregation occurred as part of the nucleation and growth of the oxide, and discrete oxide particles were never present. Orientation of the chain aggregates was related to the ice structure formed during freezing. X-ray line broadening data showed that crystallite size is a function of the 1/5 to 1/7 power of time for isothermal treatments. A qualitative analysis of material transport favored the surface diffusion mechanism.     

Acoustic Emission and Microcracking in Sapphire, Sintered Al2O3, Al/Al2O3 Composite, and Aluminum

A range of materials with brittle to ductile behavior (single-crystal and polycrystalline alumina, aluminum/alumina composite, and metallic aluminum) were investigated by acoustic emission (AE) methods for microcracking during hardness indentations or cooling from elevated temperatures (800°C). During indentation, the extent of crack formation (and the AE counts) decreased in the following order: sapphire, sintered alumina, aluminum/alumina composite with no microcracking in metallic aluminum. During cooling from 800°C, polycrystalline alumina exhibited more extensive microcracking than the aluminum/alumina composite, suggesting that the metallic phase in the aluminum/alumina composite absorbs stresses more than the glassy boundary phase in sintered alumina.     

Translucent Al2O3/LaAl11O18 Composite

A translucent alumina composite containing 1 vol% LaAl₁₁O₁₈, prepared by the hot isostatic pressing (HIP) method, displays both high translucency and high fracture toughness. Its total forward transmission at 600 nm is 75% (thickness 1 mm), and its bending strength and fracture toughness are estimated to be 574±15 MPa and 5.9±0.46 MPa·m^0.5, respectively. Its high translucency is due to the similarity of refractive index between the additive phase (LaAl₁₁O₁₈) and the matrix (alumina).     

Microwave Plasma Synthesis of Nanostructured γ-Al2O3 Powders

Nanostructured Al₂O₃ powders have been synthesized by combustion of aluminum powder in a microwave oxygen plasma, and characterized by X-ray diffraction and electron microscopy. The main phase is γ-Al₂O₃, with a small amount of δ-Al₂O₃. The particles are truncated octahedral in shape, with mean particle sizes of 21–24 nm. The effect of reaction chamber pressure on the phase composition and the particle size was studied. The γ-alumina content increases and the mean particle size decreases with decreasing pressure. No α-Al₂O₃ appears in the final particles. Electron microscopy studies find that a particle may contain more than one phase.     

Fabrication and Microstructure Characterization of Continuous Porous TiO2/Al2O3 Composite Membrane

Using a multipass extrusion process, continuous porous Al₂O₃ body (∼41% porosity) was produced and used as a substrate to fabricate continuous porous TiO₂/Al₂O₃ composite membrane. The diameter of the continuous pores of the porous Al₂O₃ body was about 150 μm. The TiO₂ nanopowders dip coated on the continuous pore-surface Al₂O₃ body existed as rutile and anatase phases after calcination at 520°C in air. However, after aging of the fabricated continuous porous TiO₂/Al₂O₃ composite membrane in 20% NaOH at 60°C for 24 h, a large number of TiO₂ fibers frequently observed on the pore surface. The diameter of the TiO₂ fibers was about 150 nm having a high specific surface area. However, after 48-h aging period, the diameter of the TiO₂ fibers increased, which was about 3 μm. Most of the TiO₂ fibers had polycrystalline structure having nanosized rutile and anatase crystals of about 20 nm.     

Homogeneous ZrO2–Al2O3 Composite Prepared by Nano-ZrO2 Particle Multilayer-Coated Al2O3 Particles

ZrO₂–Al₂O₃ nanocomposite particles were synthesized by coating nano-ZrO₂ particles on the surface of Al₂O₃ particles via the layer-by-layer (LBL) method. Polyacrylic acid (PAA) adsorption successfully modified the Al₂O₃ surface charge. Multilayer coating was successfully implemented, which was characterized by ξ potential, particle size. X-ray diffraction patterns showed that the content of ZrO₂ in the final powders could be well controlled by the LBL method. The powders coated with three layers of nano-ZrO₂ particles, which contained about 12 wt% ZrO₂, were compacted by dry press and cold isostatically pressed methods. After sintering the compact at 1450°C for 2 h under atmosphere, a sintered body with a low pore microstructure was obtained. Scanning electron microscopy micrographs of the sintered body indicated that ZrO₂ was well dispersed in the Al₂O₃ matrix.     

Bimodal Sintering of Al2O3/Al2O3 Platelet Ceramic Composites

The sintering behavior of an Al₂O₃ compact containing uniformly dispersed Al₂O₃ platelets has been investigated. The results reveal a significant decrease in the sintering rate as well as the formation of voids and cracklike defects in the presence of nonsinterable platelets. The addition of a small amount (2 vol%) of tetragonal-ZrO₂ particles enhances the sintering rate, increases end-point density (∼99.5% of theoretical density) and prevents formation of sintering defects.     

Microstructure Development in Al2O3-Platelet-Reinforced Ce-ZrO2/Al2O3 Composites

Composites containing Ce-ZrO₂, Al₂O₃, and aligned Al₂O₃ platelets were produced by centrifugal consolidation and pressureless sintering, followed by heat treatments at 1600°C for varied duration. Constituents in the consolidated microstructures were either uniformly distributed throughout or segregated into gradient layers, depending critically on platelet content. Quantitative image analysis was used to examine microstructure development with heat treatment. Changes in the volume fraction, dimensional anisotropy, and gradient of pores and platelets, as well as changes in the phase gradient, were quantified. Microstructure development was strongly dependent on the initial microstructure design attained from suspension processing.     

SiC-Whisker-Reinforced Al2O3 Composites by Free Sintering of Coated Powders

SiC whiskers were coated with a thick cladding of finegrained Al₂O₃ powder by controlled heterogeneous precipitation in a concentrated suspension of whiskers. After calcination, the coated whiskers were compacted by cold isostatic pressing and sintered at a constant heating rate of 5°C/min in a helium atmosphere. The parameters which control the coating process and the sintering characteristics of the consolidated powders are reported. Starting with an initial matrix density of 40–45% of the theoretical, composites containing up to ≅20 vol% whiskers (aspect ratio ≅15) were sintered freely to nearly theoretical density below 1800°C. By comparison, a similar composite formed by mechanical mixing of the whiskers and the precipitated Al₂O₃ powder reached a density of only 68% of the theoretical after sintering under identical conditions. For a fixed whisker content, the sinterability of the composites formed from the coated whiskers shows a fairly strong dependence on the whisker aspect ratio.     

Hydration of 3CaO·Al2O3 and 3CaO·Al2O3+] Gypsum With and Without CaCl2

Paste samples of tricalcium aluminate alone, with CaCl₂, with gypsum, and with gypsum and CaCl₂ were hydrated for up to 6 months and the hydration products characterized by SEM, XRD, and DTA. Tricalcium aluminate hydrated initially to a hexagonal hydroaluminate phase which then changed to the cubic form; the transformation rate depended on the size and shape of the sample and on temperature. The addition of CaCl₂ to tricalcium aluminate resulted in the formation of 3CaO · Al₂O₃· CaCl₂·10H₂O and 4CaO · Al₂O₃· 13H₂O, or a solid solution of the two. The chloride retarded the formation of the cubic phase 3CaO · Al₂O₃· 6H₂O; the addition of gypsum resulted in the formation of monosulfoaluminate with a minor amount of ettringite. When chloride was added to tricalcium aluminate and gypsum, more ettringite was formed, although 3CaO · Al₂O₃· CaSO₄· 12H₂O and 3CaO · Al₂O₃· CaCl₂· 10H₂O were the main hydration products.     

Formation of SiO2, Al2O3, and 3Al2O3. 2SiO2 Particles in a Counterflow Diffusion Flame

SiO₂, Al₂O₃, and 3Al₂O₃.2SiO₂ powders were synthesized by combustion of SiCl₄ or/and AlCl₃ using a counterflow diffusion flame. The SiO₂ and Al₂O₃ powders produced under various operation conditions were all amorphous and the particles were in the form of agglomerates of small particles (mostly 20 to 30 nm in diameter). The 3Al₂O₃.2SiO₂ powder produced with a low-temperature flame was also amorphous and had a similar morphology. However, those produced with high-temperature flames had poorly crystallized mullite and spinel structure, and the particles, in addition to agglomerates of small particles (20 to 30 nm in diameter), contained larger, spherical particles 150 to 130 nm in diameter). Laser light scattering and extinction measurements of the particle size and number density distributions in the flame suggested that rapid fusion leading to the formation of the larger, spherical particles occurred in a specific region of the flame.     

Interreaction Between Al2O3 and a CaO-Al2O3 Melt

Poly crystalline and single-crystalline α-alumina were reacted with a eutectic CaO-Al₂O₃ melt at 1530°C. A reaction zone develops in which a strongly textured CA₆ layer, as well as a CA₂ layer, forms, with a remaining layer of unreacted CaO-AI₂O₃ melt. Silica, an impurity in the α-alumina, is rejected by the advancing CA₆ phase and accumulates as calcium alumino-silicates in channels that assist in the reaction as fast transport paths. Reaction mechanisms and welding are briefly discussed.     

Wet Milling of Fe/Al/Al2O3 and Fe2O3/Al/Al2O3 Powder Mixtures

Wet milling of Al₂O₃-aluminide alloy (3A) precursor powders in acetone has been investigated by milling Fe/Al/Al₂O₃ and Fe₂O₃/Al/Al₂O₃ powder mixtures. The influence of the milling process on the physical and chemical properties of the milled powders has been studied. Particle refinement and homogenization were found not to play a dominant role, whereas plastic deformation of the metal particles leads to the formation of dislocations and a highly disarranged polycrystalline structure. Although no chemical reactions among the powder components in Fe₂O₃/Al/Al₂O₃ powder mixtures were observed, the formation of a nanocrystalline, ordered intermetallic FeAl phase in Fe/Al/Al₂O₃ powder mixtures caused by mechanical alloying was detected. Chemical reactions of Fe and Al particle surfaces with the atmosphere and the milling media lead to the formation of highly porous hydroxides on the particle surfaces. Hence the specific surface area of the powders increases, while the powder density decreases during milling. The fraction of Fe oxidized during milling was determined to be 0.13. The fraction of Al oxidized during milling strongly depends on the metal content of the powder mixture. It ranges between 0.4 and 0.8.     

Preparation and Microstructure of Multi-Wall Carbon Nanotubes-Toughened Al2O3 Composite

With multi-wall carbon nanotubes (MWNTs) as reinforcement, a 12 vol% MWNTs/alumina (Al₂O₃) ceramic composite was obtained by hot pressing. A fracture toughness of 5.55±0.26 MPa·m^1/2, 1.8 times that of pure Al₂O₃ ceramics, was achieved. Experimental results showed that the enveloping of carbon nanotubes (CNTs) with sodium dodecyl sulfate (SDS) is effective in changing the hydrophobicity of CNTs to hydrophilicity and improving the dispersion of CNTs in aqueous solution. Enveloped with SDS, CNTs can be homogeneously mixed with Al₂O₃ at a microscopic level by heterocoagulation. This mixing method can obviously improve the chemical compatibility between CNTs and Al₂O₃, which is important for enhancement of interfacial strength between them.     

Aluminum Titanate Formation by Solid-State Reaction of Fine Al2O3 and TiO2 Powders

The formation of Al₂TiO₅ has been studied in equimolar Al₂O₃-TiO₂ powder mixtures of ∼1μm particle sizes and moderate purity (∼99.8 wt%) at temperatures around 1300°C, where the free energy of formation is very small. Micro-structural development and reaction kinetics indicate that different mechanisms operate depending on the advancement of the reaction. The rapid initial reaction stage is interpreted as the nucleation-growth of Al₂TiO₅ cells in a virtually non-reacting matrix. The final reaction stage corresponds to the slow diffusion-controlled elimination of Al₂O₃ and TiO₂ dispersoids trapped during the growth of the initial Al₂TiO₅ cells.     

Slip Systems in Al2O3

Crystallographic notation for Al₂O₃ is reviewed, with particular reference to the correct basis to be used in describing slip systems. A Groves-and-Kelly calculation showed that the combination of pyramidal slip on {11¯02}<11¯01> and basal slip on (0001){112¯0} will allow homogeneous deformation of Al₂O₃ polycrystals. Furthermore, operation of either the {101¯1}<1¯011> or the {011¯2}<2¯021> slip system will also satisfy the Von Mises criterion, since each system is capable of 5 independent deformation modes. Electron microscopy of an Al₂O₃ polycrystal deformed ≅5% at 1150°C under a hydrostatic confining pressure confirmed that pyramidal slip had occurred.     

Preparation and Sintering of Monosized Al2O3-TiO2 Composite Powder

An unagglomerated, monosized Al₂O₃TiO₂ composite powder was prepared by the stepwise hydrolysis of titanium alkoxide in an Al₂O₃ dispersion. Particle size was controlled by selecting the particle size of the starting Al₂O₃ powder; TiO₂ content was determined by the amount of alkoxide hydrolyzed. A composite-powder compact containing 50 mol% TiO₂, when fired at 1350°C for 30 min, showed nearly theoretical density with aluminum titanate phase formation.