Preparation and electrochemical capacitance of cobalt oxide (Co3O4) nanotubes as supercapacitor material

Cobalt oxide (Co₃O₄) nanotubes have been successfully synthesized by chemically depositing cobalt hydroxide in anodic aluminum oxide (AAO) templates and thermally annealing at 500 °C. The synthesized nanotubes have been characterized by scanning electron microscope (SEM), transmission electron microscope (TEM) and X-ray diffraction (XRD). The electrochemical capacitance behavior of the Co₃O₄ nanotubes electrode was investigated by cyclic voltammetry, galvanostatic charge-discharge studies and electrochemical impedance spectroscopy in 6 mol L⁻¹ KOH solution. The electrochemical data demonstrate that the Co₃O₄ nanotubes display good capacitive behavior with a specific capacitance of 574 F g⁻¹ at a current density of 0.1 A g⁻¹ and a good specific capacitance retention of ca. 95% after 1000 continuous charge-discharge cycles, indicating that the Co₃O₄ nanotubes can be promising electroactive materials for supercapacitor.     

Varying carbon structures templated from KIT-6 for optimum electrochemical capacitance

Bicontinuous ordered mesoporous carbons (OMCs), fabricated from a KIT-6 template using aluminosilicate as catalyst and furfuryl alcohol as carbon source, were successfully prepared and studied as electrodes in supercapacitors. Their structures were characterized by transmission electron microscopy (TEM), small-angle X-ray diffraction (SAXD) and N₂ cryosorption methods. Using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS), the capacitive performance of the OMCs was found to be strongly dependent on the mesostructure. Specific capacitance value greater than 130 F g⁻¹ at 20 mV s⁻¹ were obtained from an OMC that featured high surface area with the existence of additional large pores to enhance the specific capacitance at high discharge rate. For the OMC with the best performance, we found that a power density as high as 4.5 kW kg⁻¹ at an energy density of 6.1 Wh kg⁻¹ can be delivered when the discharge current density is 20 A g⁻¹ and can also be continuously charged and discharged with little variation in capacitance after 2500 cycles. These results indicate that this OMC with optimized structure has potential to be used as a power component in electric vehicles.     

An activated carbon monolith as an electrode material for supercapacitors

Activated carbon binderless monoliths with high consistency and large porosity, synthesised from a mesophase pitch, are studied as electrodes for supercapacitors. The electrochemical cells prepared provided high capacitance values in sulphuric acid media (334 F g⁻¹) and very low electrical resistivity, which results in a very efficient energy storage device (12 Wh Kg⁻¹ maximum energy density and 12,000 W Kg⁻¹ maximum power density). Long-term cycling experiments showed excellent stability with a reduction of the initial capacitance values of 19% after performing 23,000 galvanostatic cycles at ∼300 mA g⁻¹.     

Polyfurfuryl alcohol derived activated carbons for high power electrical double layer capacitors

Polyfurfuryl alcohol (PFA) derived activated carbons were prepared by the acid catalysed polymerization of furfuryl alcohol, followed by potassium hydroxide activation. Activated carbons with apparent BET surface areas ranging from 1070 to 2600 m² g⁻¹, and corresponding average micropore sizes between 0.6 and 1.6 nm were obtained. The porosity of these carbons can be carefully controlled during activation and their performance as electrode materials in electric double layer capacitors (EDLCs) in a non-aqueous electrolyte (1 M Et₄NBF₄/ACN) is investigated.Carbon materials with a low average pore size (<∼0.6 nm) exhibited electrolyte accessibility issues and an associated decrease in capacitance at high charging rates. PFA carbons with larger average pore sizes exhibited greatly improved performance, with specific electrode capacitances of 150 F g⁻¹ at an operating voltage window of 0-2.5 V; which corresponds to 32 Wh kg⁻¹ and 38 kW kg⁻¹ on an active material basis. These carbons also displayed an outstanding performance at high current densities delivering up to 100 F g⁻¹ at current densities as high as 250 A g⁻¹. The exceptionally high capacitance and power of this electrode material is attributed to its good electronic conductivity and a highly effective combination of micro- and fine mesoporosity.     

LiPF6 based ethylene carbonate-dimethyl carbonate electrolyte for high power density electrical double layer capacitor

Electrochemical characteristics of the electrical double layer capacitor based on the two identical microporous carbide derived carbon C(TiC 950) electrodes in 1 M LiPF₆ ethylene carbonate-dimethyl carbonate (1:1 by volume) mixture have been studied using cyclic voltammetry and electrochemical impedance spectroscopy. Specific capacitance, phase angle, series and parallel resistances, characteristic time constant, energy and power densities etc. have been calculated and found to be dependent on the cell potential applied. Wide region of ideal polarisability ΔE ≤ 3.2 V, short characteristic time constant and high limiting capacitance 129 F g⁻¹, complex power and maximal energy and power density values have been obtained, indicating that this electrolyte can be used for high energy and power density supercapacitors. Additionally, the supercapacitors based on the partially graphitized C(VC) (applied as negatively charged electrode) and amorphous C(TiC 950) (applied as positively charged electrode) were completed and tested. The calculated energy and power densities were for asymmetrical C(VC 1100)|C(TiC 950)|1 M LiPF₆ + EC + DMC cell 26.2 Wh kg⁻¹ and 57.2 kW kg⁻¹, respectively, but for symmetrical C(TiC 950)|C(TiC 950)|1 M LiPF₆ + EC + DMC cell somewhat higher energy density 36.7 Wh kg⁻¹ and power density 83.6 kW kg⁻¹ values were established.     

Investigations of multilayer polyoxometalates-modified carbon nanotubes for electrochemical capacitors

A simple and effective method to improve over previous approaches to add pseudocapacitance to carbon substrates through deposition of polyoxometalates (POMs) was demonstrated on multi-walled carbon nanotubes (MWCNTs). By superimposing layers of different pseudocapacitive polyoxometalates, SiMo₁₂O₄₀⁻⁴ (SiMo₁₂) and PMo₁₂O₄₀⁻³ (PMo₁₂), the POMs exhibited continuous overlapped oxidation/reduction reactions and achieved an up to fourfold increase in area specific capacitance when compared with the double layer capacitance of bare MWCNTs. The superimposed SiMo₁₂ and PMo₁₂ layers were studied by Scanning Electron Microscopy (SEM) and X-ray Photoelectron Spectroscopy (XPS). Analyses of the potential/pH relationship provided important insights into the deposition mechanism and suggested that the layer closest to the electrode substrate was dominating in terms of chemistry and kinetics of the coated MWCNT.     

Polyaniline nanofibers obtained by interfacial polymerization for high-rate supercapacitors

Polyaniline (PANI) nanofibers were fabricated by interfacial polymerization in the presence of para-phenylenediamine (PPD). The additives cannot only have a profound impact on the polymers morphology, but can also improve their specific energy and specific capacitances. It was found that PANI nanofibers prepared in the presence of PPD were longer and less entangled than those in the absence of PPD due to a much faster polymerization rate in initial stage. A specific capacitance value of 548 F g⁻¹, a specific power value of 127 W kg⁻¹ and a specific energy value of 36 Wh kg⁻¹ were obtained in polyaniline nanofibers prepared in the present of PPD at a constant discharge current density of 0.18 A g⁻¹.     

Effect of pore size distribution of coal-based activated carbons on double layer capacitance

A series of coal-based activated carbons representing a wide range of mesopore content, from 16.7 to 86.9%, were investigated as an electrode in electric double layer capacitors (EDLCs) in 1 mol l⁻¹ H₂SO₄ and 6 mol l⁻¹ KOH electrolytic solutions. The activated carbons (ACs) used in this study were produced from chemically modified lignite, subbituminous and bituminous coals by carbonization and subsequent activation with steam. The BET surface area of ACs studied ranged from 340 to 1270 m² g⁻¹. The performance of ACs as EDLC electrodes was characterized using voltammetry, galvanostatic charge/discharge and impedance spectroscopy measurements. For the carbons with surface area up to 1000 m² g⁻¹, the higher BET surface area the higher specific capacitance (F g⁻¹) for both electrolytes. The surface capacitance (μF cm⁻²) increases also with the mesopore content. The optimum range of mesopore content in terms of the use of ACs studied for EDLCs was found to be between 20 and 50%. A maximum capacitance exceeding 160 F g⁻¹ and a relatively high surface capacitance about 16 μF cm⁻² measured in H₂SO₄ solution were achieved for the AC prepared from a sulfonated subbituminous coal. This study shows that the ACs produced from coals exhibit a better performance as an electrode material of EDLC in H₂SO₄ than in KOH electrolytic solutions. For KOH, the capacitance per unit mesopore surface is slightly lower than that referred to unit micropore surface (9.1 versus 10.1 μF cm⁻²). However, in the case of H₂SO₄ the former capacitance is double and even higher compared with the latter (23.1 versus 9.8 μF cm⁻²). On the other hand, the capacitance per micropore surface area is the same in both electrolytes used, about 10.0 μF cm⁻².     

Improvement of the structural and chemical properties of a commercial activated carbon for its application in electrochemical capacitors

The present paper shows that the performance of an inexpensive activated carbon used in electrochemical capacitors can be significantly enhanced by a simple treatment with KOH at 850 °C. The changes in the specific surface area, as well as in the surface chemistry, lead to high capacitance values, which provide a noticeable energy density.The KOH-treatment of a commercial activated carbon leads to highly pure carbons with effective surface areas in the range of 1300-1500 m² g⁻¹ and gravimetric capacitances as high as three times that of the raw carbon.For re-activated carbons, one obtains at low current density (50 mA g⁻¹) values of 200 F g⁻¹ in aqueous electrolytes (1M H₂SO₄ and 6M KOH) and around 150 F g⁻¹ in 1M (C₂H₅)₄NBF₄ in acetonitrile. Furthermore, the resulting carbons present an enhanced and stable performance for high charge/discharge load in organic and aqueous media.This work confirms the possibilities offered by immersion calorimetry on its own for the prediction of the specific capacitance of carbons in (C₂H₅)₄NBF₄/acetonitrile. On the other hand, it also shows the limitations of this technique to assess, with a good accuracy, the suitability of a carbon to be used as capacitor electrodes operating in aqueous electrolytes (H₂SO₄ and KOH).     

EDLC performance of carbide-derived carbons in aprotic and acidic electrolytes

This study shows that carbide-derived carbons (CDCs) with average pore size distributions around 0.9-1 nm and effective surface areas of 1300-1400 m² g⁻¹ provide electrochemical double-layer capacitors with high performances in both aqueous (2M H₂SO₄) and aprotic (1M (C₂H₅)₄NBF₄ in acetonitrile) electrolytes.In the acidic electrolytic solution, the gravimetric capacitance at low current density (1 mA cm⁻²) can exceed 200 F g⁻¹, whereas the volumetric capacitance reaches 90 F cm⁻³. In the aprotic electrolyte they reach 150 F g⁻¹ and 60 F cm⁻³.A detailed comparison of the capacitive behaviour of CDCs at high current density (up to 100 mA cm⁻²) with other microporous and mesoporous carbons indicates better rate capabilities for the present materials in both electrolytes. This is due to the high surface area, the accessible porosity and the relatively low oxygen content.It also appears that the surface-related capacitances of the present CDCs in the aprotic electrolyte are in line with other carbons and show no anomalous behaviour.     

High capacitance properties of polyaniline by electrochemical deposition on a porous carbon substrate

Electrochemical deposition of polyaniline (PANI) is carried out on a porous carbon substrate for supercapacitor studies. The effect of substrate is studied by comparing the results obtained using platinum, stainless steel and porous carbon substrates. PANI deposited at 100 mV s⁻¹ sweep rate by potentiodynamic technique on porous carbon substrate is found to possess superior capacitance properties. Experimental variables, namely, concentrations of aniline monomer and H₂SO₄ supporting electrolyte are varied and arrived at the optimum concentrations to obtain a maximum capacitance of PANI. Low concentrations of both aniline and H₂SO₄, which produce PANI at low rates, are desirable. The PANI deposits prepared under these conditions possess network morphology of nanofibrils. Capacitance values as high as 1600 F g⁻¹ are obtained and PANI coated carbon electrodes facilitate charge-discharge current densities as high as 45 mA cm⁻² (19.8 A g⁻¹). Electrodes are found to be fairly stable over a long cycle-life, although there is some capacitance loss during the initial stages of cycling.     

High-capacitance carbon electrode prepared by PVDC carbonization for aqueous EDLCs

Porous carbons with high-volumetric capacitance in aqueous electric double layer capacitors (EDLCs) were simply prepared by poly(vinylidene chloride) (PVDC) carbonization at high temperature without activation or any other additional processes. The PVDC-derived carbon is microporous with Brunauer-Emmett-Teller (BET) surface area about 1200 m² g⁻¹. As it possesses not only high-gravimetric capacitance (262 F g⁻¹) but also high-electrode density (0.815 g cm⁻³), the PVDC-derived carbon present an outstanding high-volumetric capacitance of 214 F cm⁻³, twice over of the commercial carbon Maxsorb-3 with a high-surface area of 3200 m² g⁻¹. The PVDC-derived carbon also exhibit good rate performance, indicating that it is a promising electrode material for EDLCs.     

A sensitive amperometric bromate sensor based on multi-walled carbon nanotubes/phosphomolybdic acid composite film

An amperometric sensor for bromate was developed based on multi-walled carbon nanotubes (MWNTs)/phosphomolybdic acid (PMo₁₂) composite film coated on a pyrolytic graphite (PG) electrode. MWNTs are dispersed in PMo₁₂ aqueous solution through spontaneous and strong chemisorption between carbon and polyoxometalate, which results in a homogeneous MWNTs/PMo₁₂ composite. Due to the unique electronic and electrocatalytic properties of MWNTs and PMo₁₂, the combination of MWNTs and PMo₁₂ results in a remarkable synergistic augmentation on the response current. The bromate sensor based on the PG/MWNTs/PMo₁₂ electrode has excellent characteristics, such as a detection limit of 0.5 μM, a sensitivity of 760.9 μA mM⁻¹ cm⁻², a response time less than 2 s and a linear range from 5 μM to 15 mM.     

Multiwall carbon nanotube supported poly(3,4-ethylenedioxythiophene)/manganese oxide nano-composite electrode for super-capacitors

MWCNT-PSS/PEDOT/MnO₂ nano-composite electrodes were fabricated by generating pseudo-capacitive poly(3,4-ethylenedioxythiophene) (PEDOT)/MnO₂ nano-structures on poly(styrene sulfonate) (PSS) dispersed multiwalled carbon nanotubes (MWCNTs). PSS dispersed MWCNTs (MWCNT-PSS) facilitated the growth of PEDOT and MnO₂ into nano-rods with large active surface area and good electrical conductivity. The ternary MWCNT-PSS/PEDOT/MnO₂ nano-composite electrode was studied for the application in super-capacitors, and exhibited excellent capacitive behavior between −0.2 V and 0.8 V (vs. saturated Ag/AgCl electrode) with high reversibility. Specific capacitance of the nano-composite electrode was found as high as 375 F g⁻¹. In contrast, specific capacitance of MWCNT-PSS/MnO₂ and MWCNT-PSS nano-composite electrodes is 175 F g⁻¹ and 15 F g⁻¹, respectively. Based on cyclic voltammetric studies and cycle-life tests, the MWCNT-PSS/PEDOT/MnO₂ nano-composite electrode gave a highly stable and reversible performance up to 2000 cycles. Our studies demonstrate that the synergistic combination of MWCNT-PSS, PEDOT and MnO₂ has advantages over the sum of the individual components.     

Electrode properties of a double layer capacitor of nano-structured graphite produced by ball milling under a hydrogen atmosphere

Nano-structural graphite prepared by ball milling under H₂ or Ar atmosphere was studied as an electrode for electric double layer capacitors (EDLCs) by means of a conventional 2-electrode galvanostatic method. Especially, the product prepared under H₂ atmosphere using zirconia balls revealed 500 m² g⁻¹ surface area and showed 12 F g⁻¹ specific capacitance, which was comparable to that of an activated carbon with large specific surface area of 3000 m² g⁻¹ examined as a reference. A proper condition of the milling time is rather a shorter time than ∼8 h, where the graphitic feature is remained in the ball milled product. On the other hand, for the sample prepared by using steel balls, the specific capacitance per surface area was several hundreds times smaller than the others, indicating that the small amount of Fe contamination during milling played a negative role for the EDLC properties.     

Mesoporous RuO2 for the next generation supercapacitors with an ultrahigh power density

The 3D mesoporous, well crystalline RuO₂ film prepared via the evaporation-induced self-assembled method (EISA) successfully demonstrates the extremely high power performances (e.g., excellent capacitive behavior at 10,000 mV s⁻¹, ultrahigh-frequency capacitive responses (the absence of a knee point in the Nyquist plot), and 2.6 MW kg⁻¹ with an acceptable energy density of 4.6 Wh kg⁻¹). These excellent capacitive performances were identified by means of voltammetric and electrochemical impedance spectroscopic (EIS) analyses. The mesoporous (with mean pore spacing of 18.1 nm) and crystalline nature of this film was characterized by means of the field emission scanning electron microscopy (FE-SEM), Brunaur-Emmett-Teller (BET) method, small-angle X-ray scattering (SAXRS), high-resolution transmission electron microscopy (HR-TEM), electron diffraction (ED), and X-ray diffraction (XRD) analyses. This mesoporous, well crystalline RuO₂ film constrains the redox transition to the superficial region meanwhile the tailored mesoporous structure increases the electrochemically active centers, promotes the penetration of electrolytes, provides the “proton reservoirs”, and enhances the rate of electron transport simultaneously for the ultrahigh power application. The specific capacitance of this mesoporous RuO₂ can be enhanced from 84 to 185 F g⁻¹ after the microwave-assisted hydrothermal treatment.     

Investigation of polymer electrolyte hybrid supercapacitor based on manganese oxide-carbon electrodes

A hybrid supercapacitor based on manganese oxide, activated carbon and polymer electrolyte was developed and electrochemically investigated. The capacitive performance obtained from the polymer electrolyte based supercapacitor was similar to that of an aqueous electrolyte based supercapacitor, tested for comparison in the same operative conditions. A durability test carried out for 2500 cycles showed stable and slowly increasing performance. The specific capacitance of hybrid supercapacitor was 48 F g⁻¹ (192 F g⁻¹ as a mean one electrode capacitance), in which that of the positive electrode was 384 F g⁻¹ of MnO₂ and that of negative electrode 117 F g⁻¹ of carbon. The impedance analysis evidenced that although the polymer electrolyte based hybrid supercapacitor showed higher resistance compared to that of the liquid electrolyte based supercapacitor, this drawback was counterbalanced by better ion transport features, which were evident at lower frequencies, where similar values of capacitances were obtained from the different supercapacitors.     

Activated carbon fiber cloths as electrodes for high performance electric double layer capacitors

Activated carbon fiber cloth (ACFC) electrodes with high double layer capacitance and good rate capability were prepared from polyacrylonitrile (PAN) fabrics by optimizing the carbonization temperature prior to CO₂ activation. The carbonization temperature has a marked effect on both the pore structure and the electrochemical performances of the ACFCs. Moderate carbonization at 600 °C results in higher specific surface area and larger pore size, and hence higher capacitance and better rate capability. The specific capacitance of the ACFCs in 6 mol L⁻¹ KOH aqueous solution can be as high as 208 F g⁻¹. It remains 129 F g⁻¹ as the current density increases to 10 000 mA g⁻¹.     

Preparation, characterization and electrocatalytic properties of poly(luminol) and polyoxometalate hybrid film modified electrodes

Hybrid films composed of poly(luminol) and nanometer-sized clusters of polyoxometalate, SiMo₁₂O₄₀⁴⁻ and PMo₁₂O₄₀³⁻ have been prepared in acidic aqueous solutions. These films are stable and electrochemically active, and produced on glassy carbon, platinum, gold and transparent semiconductor tin oxide electrodes. The electrochemical quartz crystal microbalance and cyclic voltammetry were used to study in situ growth of the hybrid poly(luminol)/SiMo₁₂O₄₀⁴⁻ and poly(luminol)/PMo₁₂O₄₀³⁻. Both the poly(luminol)/SiMo₁₂O₄₀⁴⁻ and poly(luminol)/PMo₁₂O₄₀³⁻ hybrid films showed four redox couples and the electrochemical properties were compared to SiMo₁₂O₄₀⁴⁻ and PMo₁₂O₄₀³⁻. When transferred to various acidity aqueous solutions, the four redox couples and the formal potentials of two hybride film were observed to be pH-dependent. The electrocatalytic reduction of ClO₃⁻, BrO₃⁻, IO₃⁻, S₂O₈²⁻ and NO₂⁻ by a poly(luminol)/PMo₁₂O₄₀³⁻ hybrid film in an acidic aqueous solution showed an electrocatalytic reduction activity of IO₃⁻ > BrO₃⁻ and ClO₃⁻. The electrocatalytic oxidation of dopamine and epinephrine by a poly(luminol)/PMo₁₂O₄₀³⁻ hybrid film was also investigated.     

Factors influencing MnO2/multi-walled carbon nanotubes composite's electrochemical performance as supercapacitor electrode

Poor crystallined α-MnO₂ grown on multi-walled carbon nanotubes (MWCNTs) by reducing KMnO₄ in ethanol are characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and Brunauer-Emmett-Telle (BET) surface area measurement, which indicate that MWCNTs are wrapped up by poor crystalline MnO₂ and BET areas of the composites maintain the same level of 200 m² g⁻¹ as the content of MWCNTs in the range of 0-30%. The electrochemical performances of the MnO₂/MWCNTs composites as electrode materials for supercapacitor are evaluated by cyclic voltammetry (CV) and galvanostatic charge-discharge measurement in 1 M Na₂SO₄ solution. At a scan rate of 5 mV s⁻¹, rectangular shapes could only be observed for the composites with higher MWCNTs contents. The effect of additional conductive agent KS6 on the electrochemical behavior of the composites is also studied. With a fixed carbon content of 25% (MWCNTs included), MnO₂ with 20% MWCNTs and 5% KS6 has the highest specific capacitance, excellent cyclability and best rate capability, which gives the specific capacitance of 179 F g⁻¹ at a scan rate of 5 mV s⁻¹, and remains 114.6 F g⁻¹ at 100 mV s⁻¹.