首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
The lifetime and performance of a direct methanol fuel cell (DMFC) were investigated to understand the correlation between the structure of catalysts/membrane and cell performance versus time. The cell polarization and performance curves were obtained during the DMFC operation with the time. The catalysts and Nafion® membrane of the membrane electrode assembly (MEA) from the lifetime test were comprehensively examined by XRD, HRTEM, FTIR and Raman spectroscopy techniques. The results revealed that there was significant performance degradation during the first 200 h operation; while the degradation was slowing down between 200 and 704 h operation. The degradation became worse after 1002 h operation. The increases of the catalyst particle size from both anode and cathode catalysts were observed after the DMFC lifetime test. The changes of microstructure, surface composition, the interfacial structure of the MEA, and the aging of Nafion® under the DMFC lifetime tests were also observed.  相似文献   

2.
The effect of carbon type, carbon loading and microporous layer structure in the microporous layer on the performance of a direct methanol fuel cell (DMFC) at low temperature was investigated using electrochemical polarization techniques, electrochemical impedance spectroscopy, scanning electron microscope and other methods. Vulcan XC-72 carbon was found to be most suitable as a microporous layer for low temperature DMFC. Maximum fuel cell performance was obtained utilizing a microporous layer with carbon loading of 1.0 mg cm−2 when air was used as an oxidant. A membrane electrode assembly with 1.0 mg cm−2 Vulcan XC-72 carbon with 20 wt.% Teflon in the cathode and no microporous layer in the anode showed a maximum power density of 36.7 mW cm−2 at 35 °C under atmospheric pressure. The AC impedance study proved that a cell with a dissymmetrical microporous layer structure had lower internal resistance and mass transfer resistance, thus obtaining better performance.  相似文献   

3.
Recently electrodes for direct methanol fuel cell (DMFC) have been developed for getting high fuel cell performances by controlling composition of catalysts and sulfonated polymers, developing catalyst particles, modifying carbon supports, etc. The electrodes in DMFCs are porous layers, which are composed of catalyst, which is black or carbon supported, and sulfonated polymers in a blended form. In the present study, carbon support for catalysts was functionalized to play dual roles of a mass transport and a catalyst support. The functionalized carbon support was characterized and compared with pristine one by thermal and spectroscopic analysis, and loading of platinum (Pt) catalysts on modified support was performed by gas reduction. The electrodes with Pt on functionalized carbon support were fabricated, though the conventional electrodes were prepared with sulfonated polymer and Pt catalysts. Membrane electrode assembly with Pt catalyst on functionalized support showed a higher DMFC performance of 30 mW cm−2 at 50 °C without using additional sulfonated polymer. Integration of electrode components in one body has another advantage of easier and simpler process in preparing electrodes for DMFCs. Improved DMFC performance of the electrode containing functionalized carbon was be attributed to a better mass transport which maximize the catalytic activities.  相似文献   

4.
A silicon-based micro direct methanol fuel cell (μDMFC) for portable applications has been developed and its electrochemical characterization carried out in this study. Anode and cathode flowfields with channel and rib width of 750 μm and channel depth of 400 μm were fabricated on Si wafers using the microelectromechanical system (MEMS) technology. A membrane-electrode assembly (MEA) was specially fabricated to mitigate methanol crossover. This MEA features a modified anode backing structure in which a compact microporous layer is added to create an additional barrier to methanol transport thereby reducing the rate of methanol crossing over the polymer membrane. The cell with the active area of 1.625 cm2 was assembled by sandwiching the MEA between two micro-fabricated Si wafers. Extensive cell polarization testing demonstrated a maximum power density of 50 mW/cm2 using 2 M methanol feed at 60 °C. When the cell was operated at room temperature, the maximum power density was shown to be about 16 mW/cm2 with both 2 and 4 M methanol feed. It was further found that the present μDMFC still produced reasonable performance under 8 M methanol solution at room temperature.  相似文献   

5.
Membrane electrode assemblies (MEA) were prepared using PtRu black and 60 wt.% carbon-supported platinum (Pt/C) as their anode and cathode catalysts, respectively. The cathode catalyst layers were fabricated using various amounts of Pt (0.5 mg cm−2, 1.0 mg cm−2, 2.0 mg cm−2, and 3.0 mg cm−2). To study the effect of carbon support on performance, a MEA in which Pt black was used as the cathode catalyst was fabricated. In addition, the effect of methanol crossover on the Pt/C on the cathode side of a direct methanol fuel cell (DMFC) was investigated. The performance of the single cell that used Pt/C as the cathode catalyst was higher than single cell that used Pt black and this result was pronounced when highly concentrated methanol (above 2.0 M) was used as the fuel.  相似文献   

6.
The role of catalyst stability on the adverse effects of hydrogen peroxide (H2O2) formation rates in a proton exchange membrane fuel cell (PEMFC) is investigated for Pt, Pt binary (PtX, X = Co, Ru, Rh, V, Ni) and ternary (PtCoX, X = Ir, Rh) catalysts supported on ketjen black (KB) carbon. The selectivity of these catalysts towards H2O2 formation in the oxygen reduction reaction (ORR) was measured on a rotating ring disc electrode. These measured values were used in conjunction with local oxygen and proton concentrations to estimate local H2O2 formation rates in a PEMFC anode and cathode. The effect of H2O2 formation rates on the most active and durable of these catalysts (PtCo and PtIrCo) on Nafion membrane durability was studied using a single-sided membrane electrode assembly (MEA) with a built-in reference electrode. Fluoride ion concentration in the effluent water was used as an indicator of the membrane degradation rate. PtIrCo had the least fluorine emission rate (FER) followed by PtCo/KB and Pt/KB. Though PtCo and PtIrCo show higher selectivity for H2O2 formation than unalloyed Pt, they did not contribute to membrane degradation. This result is explained in terms of catalyst stability as measured in potential cycling tests in liquid electrolyte as well as in a functional PEM fuel cell.  相似文献   

7.
The performance of a proton exchange membrane fuel cell (PEMFC) with gas diffusion cathodes having the catalyst layer applied directly onto Nafion membranes is investigated with the aim at characterizing the effects of the Nafion content, the catalyst loading in the electrode and also of the membrane thickness and gases pressures. At high current densities the best fuel cell performance was found for the electrode with 0.35 mg Nafion cm−2 (15 wt.%), while at low current densities the cell performance is better for higher Nafion contents. It is also observed that a decrease of the usual Pt loading in the catalyst layer from 0.4 to ca. 0.1 mg Pt cm−2 is possible, without introducing serious problems to the fuel cell performance. A decrease of the membrane thickness favors the fuel cell performance at all ranges of current densities. When pure oxygen is supplied to the cathode and for the thinner membranes there is a positive effect of the increase of the O2 pressure, which raises the fuel cell current densities to very high values (>4.0A cm−2, for Nafion 112—50 μm). This trend is not apparent for thicker membranes, for which there is a negligible effect of pressure at high current densities. For H2/air PEMFCs, the positive effect of pressure is seen even for thick membranes.  相似文献   

8.
We investigate the performance of air-breathing laminar flow-based fuel cells (LFFCs) operated with five different fuels (formic acid, methanol, ethanol, hydrazine, and sodium borohydride) in either acidic or alkaline media. The membraneless LFFC architecture enables interchangeable operation with different fuel and media combinations that are only limited by the actual anode catalyst used. Furthermore, operating under alkaline conditions significantly improves methanol and ethanol oxidation kinetics and stabilizes sodium borohydride. LFFCs operated with hydrazine and sodium borohydride as fuels exhibit power densities of 80 and 101 mW/cm2, respectively. To optimize anode performance, particularly for ethanol electro-oxidation, we introduced a hydrogen cathode to the membraneless LFFC design which renders the cell an ideal platform for anode investigation. Here, we highlight two simple diagnostic methods, in situ single electrode studies and electrochemical impedance spectroscopy (EIS), for characterizing and optimizing the performance of a direct ethanol LFFC anode.  相似文献   

9.
This work reports on the oxygen reduction activity of several non-precious metal (non-PGM) catalysts for oxygen reduction reaction (ORR) at the fuel cell cathode, including pyrolyzed CoTPP, FeTPP, H2TMPP, and CoTMPP. Of the studied catalysts, pyrolyzed CoTMPP (Co-tetramethoxyphenylporphyrin) was found to perform significantly better than other materials. The catalyst underwent a thorough testing in both hydrogen-air polymer electrolyte fuel cell (PEFC) and direct methanol fuel cell (DMFC). It was found that CoTMPP cathode can sustain currents that are only 2-3 times lower than those obtained with a conventional Pt-black cathode in an H2-air PEFC. DMFC experiments, including methanol crossover and methanol tolerance measurements, indicate high ORR selectivity of the CoTMPP catalyst. Based on results obtained to date, the CoTMPP-based catalyst offers promise for the use in conventional and mixed-reactant DMFCs operating with concentrated methanol feeds. However, hydrogen-air fuel cell life data, consisting of over 800 h of continuous cell operation, indicate that improvement to long-term stability of the CoTMPP catalyst will be required to make it practical.  相似文献   

10.
Hansan Liu 《Electrochimica acta》2007,52(13):4532-4538
Ultrasonic spray pyrolysis (USP) was used to synthesize a high-surface-area CoTMPP/C catalyst for oxygen reduction reaction (ORR). SEM micrographs showed that the USP-derived CoTMPP/C consists of spherical, porous and uniform particles with a diameter of 2-5 μm, which is superior to that with a random morphology and large particle sizes (up to 100 μm) synthesized by the conventional heat-treatment method. BET results revealed that the USP-derived catalyst had a higher specific surface area (834 m2 g−1) than the conventional one. Cyclic voltammetric, rotating ring-disk electrode (RRDE) and H2-air PEM fuel cell testing were employed to evaluate the USP-derived CoTMPP/C. The kinetic current density of the USP-derived catalyst at 0.7 V versus NHE was two times higher than that of the conventional catalyst. Compared to Pt/C catalyst, the USP-derived CoTMPP/C catalyst showed a strong methanol tolerance and a higher ORR activity in the presence of methanol. In a H2-air PEM fuel cell with USP-derived CoTMPP/C as the cathode catalyst, the cell performance was much higher than that with conventional heat-treated CoTMMP/C as the catalyst.  相似文献   

11.
This paper presents results of recent investigations to develop an optimized in-house membrane electrode assembly (MEA) preparation technique combining catalyst ink spraying and assembly hot pressing. Only easy steps were chosen in this preparation technique in order to simplify the method, aiming at cost reduction. The influence of MEA fabrication parameters like electrode pressing or annealing on the performance of hydrogen fuel cells was studied by single cell measurements with H2/O2 operation. Toray paper and carbon cloth as gas diffusion layer (GDL) materials were compared and the composition of electrode inks was optimized with regard to most favorable fuel cell performance. Commercial E-TEK catalyst was used on the anode and cathode with Pt loadings of 0.4 and 0.6 mg/cm2, respectively. The MEA with best performance delivered approximately 0.58 W/cm2, at 65 °C cell temperature, 80 °C anode humidification, dry cathode and ambient pressure on both electrodes. The results show, that changing electrode compositions or the use of different materials with same functionality (e.g. different GDLs), have a larger effect on fuel cell performance than changing preparation parameters like hot pressing or spraying conditions, studied in previous work.  相似文献   

12.
The durability of the membrane electrode assembly (MEA) for direct methanol fuel cells (DMFCs) is one of the most critical issues to be addressed before widespread commercialization of the DMFC technology. In this work, we investigated the effect of the hot-pressing duration on the performance and durability of the MEA prepared by hot-pressing technique. It was found that the 60-min hot pressing at 135 °C under the pressure of 4.0 MPa yielded a significantly improved MEA durability than did the 3-min hot pressing (a typical duration in practice) under the same condition, but no substantial difference was found in the cell performance of the MEAs prepared with the two different hot-pressing durations. The reason why the hot-pressing duration had no significant effect on cell performance is explained based on X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FT-IR) characterizations of the changes in the physiochemical properties of MEAs and their constituent components, including the anode, cathode and Nafion membrane, before and after hot pressing with different durations.  相似文献   

13.
For this study, catalyst layers for polymer electrolyte membrane fuel cells (PEMFC) were prepared by spraying and sputtering to deposit Pt amount of 0.1 and 0.01 mg cm−2, respectively. These Pt layers were then assembled to fabricate membrane electrode assemblies (MEA) having either single- or double-layered catalysts. The PEM fuel cell with double layers showed a current density of 777 mA cm−2 at a cell voltage of 0.6 V, which is a higher current density than state-of-the-art fuel cells at 643 mA cm−2. These results indicate that Pt loading in state-of-the-art PEMFCs could be reduced by approximately 50% with no performance loss by using both spraying and sputtering method in the MEA fabrication process.  相似文献   

14.
An alkaline microfluidic fuel cell is demonstrated employing an alkaline version of a formic acid anode and a sodium hypochlorite cathode. Both sodium formate fuel and sodium hypochlorite oxidant are available and stable as highly concentrated solutions, thereby facilitating fuel cell systems with high overall energy density. Sodium hypochlorite is commonly available as hypochlorite bleach. The alkaline anodic half-cell produces carbonate rather than the less-desirable gaseous CO2, while sustaining the rapid kinetics associated with formic acid oxidation in acidic media. Both half-cells provide high current densities at relatively low overpotentials and are free of gaseous products that may otherwise limit microfluidic fuel cell performance. The microfluidic fuel cell takes advantage of a recently developed membraneless architecture with flow-through porous electrodes. Power densities up to 52 mW cm−2 and overall energy conversion efficiencies up to 30% per single pass are demonstrated at room temperature using 1.2 M formate fuel and 0.67 M hypochlorite oxidant. The alkaline formate/hypochlorite fuel and oxidant combination demonstrated here, or either one of its individual half-cells, may also be useful in conventional membrane-based fuel cell designs.  相似文献   

15.
In this work, a novel self-humidifying membrane electrode assembly (MEA) with Pt/SiO2/C as anode catalyst was developed to improve the performance of proton exchange membrane fuel cell (PEMFC) operating at low humidity conditions. The characteristics of the composite catalysts were investigated by XRD, TEM and water uptake measurement. The optimal performance of the MEA was obtained with the 10 wt.% of silica in the composite catalyst by single cell tests under both high and low humidity conditions. The low humidity performance of the novel self-humidifying MEA was evaluated in a H2/air PEMFC at ambient pressure under different relative humidity (RH) and cell temperature conditions. The results show that the MEA performance was hardly changed even if the RHs of both the anode and cathode decreased from 100% to 28%. However, the low humidity performance of the MEA was quite susceptible to the cell temperature, which decreased steeply as the cell temperature increased. At a cell temperature of 50 °C, the MEA shows good stability for low humidity operating: the current density remained at 0.65 A cm−2 at a usual work voltage of 0.6 V without any degradation after 120 h operation under 28% RH for both the anode and cathode.  相似文献   

16.
直接甲醇燃料电池   总被引:1,自引:0,他引:1  
介绍了直接甲醇燃料电池的原理、结构,并与发展较早的氢气燃料电池进行优劣比较。针对近期商业化便携式燃料电池的技术指标,主要讨论了直接甲醇燃料电池在性能和成本上的现状和问题,并着重阐述了阳极催化剂和电解质膜(决定其性能的两个关键因素)的研发进展。  相似文献   

17.
The potential-current fuel cell characteristics of membrane electrode assemblies (MEAs) using hexafluorinated sulfonated poly(ether sulfone) copolymer are compared to those of Nafion® based MEAs in the case of proton exchange membrane fuel cell (PEMFC) and direct methanol fuel cell (DMFC). The hexafluorinated copolymer with 60 mol% of monosulfonated comonomer based acid form membrane is chosen for this study due to its high proton conductivity, high thermal stability, low methanol permeability, and its insolubility in boiling water. The catalyst powder is directly coated on the membrane and the catalyst coated membrane is used to fabricate MEAs for both fuel cells. A current density of 530 mA cm?2 at 0.6 V is obtained at 70 °C with H2/air as the fuel and oxidant. The peak power density of 110 mW cm?2 is obtained at 80 °C under specific DMFC operating conditions. Other electrochemical characteristics such as electrochemical impedance spectroscopy, cyclic voltammetry, and linear sweep voltammetry are also studied.  相似文献   

18.
A study of a direct methanol alkaline fuel cell (DMAFC) operating with sodium conducting membranes is reported. Evaluation of the fuel cell was performed using membrane electrode assemblies incorporating carbon supported platinum catalysts and Nafion® 117 and 112 membranes. A membrane electrode assembly was also prepared by the direct chemical deposition of platinum into the surface region of the membrane. Evaluation of the chemically deposited assembly showed it to be less active than those based on carbon supported catalysts. SEM &; TEM analysis indicate that this behaviour is due to the low surface area of the chemically deposited catalyst layer. The fuel cell performance with Nafion membranes is reported and is not as good as achieved with hydroxide ion conducting membranes suggesting that Nafion may not be suitable for DMAFC operation.  相似文献   

19.
The ‘impregnation-reduction method’ has been investigated as a tool for the preparation of a direct methanol fuel cell (DMFC) anode. In this method, PtRu electrocatalysts were directly bonded onto a polymer electrolyte membrane by the chemical reduction of a mixture of Pt and Ru complexes impregnated in the membrane. The deposited PtRu particles were embedded in the 3-4 μm region of the membrane surface to form a porous and hydrophilic layer. The PtRu layers turned out to be applicable to the DMFC anode, despite their small active surface areas compared to PtRu nanoparticles used in the conventional method. Approximately, 3 mg cm−2 of the PtRu layer exhibited better catalyst utilization and facilitated the release of evolving CO2. This preparation technique is attractive for the application of various solid polymer electrolyte materials with low heat-resistance or various shapes, etc.  相似文献   

20.
Micelle-encapsulated multi-walled carbon nanotubes (MWCNTs) with sodium dodecyl sulfate (SDS) were used as catalyst support to deposit platinum nanoparticles. High resolution transmission electron microscopy (HRTEM) images reveal the crystalline nature of Pt nanoparticles with a diameter of ∼4 nm on the surface of MWCNTs. A single proton exchange membrane fuel cell (PEMFC) with total catalyst loading of 0.2 mg Pt cm−2 (anode 0.1 and cathode 0.1 mg Pt cm−2, respectively) has been evaluated at 80 °C with H2 and O2 gases using Nafion-212 electrolyte. Pt/MWCNTs synthesized by using modified SDS-MWCNTs with high temperature treatment (250 °C) showed a peak power density of 950 mW cm−2. Accelerated durability evaluation was carried out by conducting 1500 potential cycles between 0.1 and 1.2 V with 50 mV s−1 scan rate, H2/N2 at 80 °C. The membrane electrode assembly (MEA) with Pt/MWCNTs showed superior performance stability with a power density degradation of only ∼30% compared to commercial Pt/C (70%) after potential cycles.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号