An electrochemical quartz crystal microbalance study into the deposition of manganese dioxide

An electrochemical quartz crystal microbalance (EQCM) has been used to study the effects of electrolyte composition (MnSO₄ and H₂SO₄ concentrations) and anodic current density on the electrodeposition of manganese dioxide. The EQCM, in tandem with the electrode voltage during deposition, has been used to characterize features of the deposition mechanism such as the relative lifetime of the Mn(III) intermediate, the rate of soluble Mn(III) hydrolysis to form MnOOH, and the porosity of the resultant manganese dioxide deposit as a function of crystal nucleation. The connection between the results obtained here and commercial electrodeposition of manganese dioxide were also discussed.     

Application of the electrochemical quartz crystal microbalance technique to copper sonoelectrochemistry: Part 1. Sulfate-based electrolytes

The applicability of the electrochemical quartz crystal microbalance technique in an ultrasonic field created by an ultrasound probe is demonstrated for the electrodeposition of copper. Cyclic voltammetry and potentiostatic depositions in acidic sulfate-based copper electrolytes were performed at different ultrasonic intensities. The electrochemical quartz crystal microbalance was operated in ultrasonic fields with intensities up to 30 W cm⁻². For cyclic voltammetry, potential resolved and averaged (apparent) current efficiencies were calculated from mass and charge data in function of the amplitude of the ultrasonic horn. Ultrasound slightly affected the current efficiencies during copper deposition in cyclic voltammetry, but did not change the efficiencies during dissolution. During potentiostatic depositions the current efficiency increased from 84% to almost 100% upon application of ultrasound. Morphology of deposits prepared by potentiostatic depositions was analyzed by scanning electron microscopy, and found to be different at high ultrasonic intensities.     

Preparation of the molecularly imprinted polymers-based capacitive sensor specific for tegafur and its characterization by electrochemical impedance and piezoelectric quartz crystal microbalance

Molecularly imprinted polymers (MIPs)-based capacitive sensor specific for tegafur was constructed by electropolymerization of m-aminophenol onto the surface of gold electrode and the Au-coated quartz crystal electrodes. Electrochemical impedance (EI) and quartz crystal microbalance (QCM) were employed to characterize the modified gold electrodes and the modified Au-coated quartz crystals, respectively. Unlike the capacitive sensors reported in the previous literatures, the present sensors were not treated with alkanethiol after electropolymerization and show even more satisfactory performance. QCM measurements also confirmed the imprinting effect of the polymer layers.     

Influence of electrochemical potential on the tribocorrosion behaviour of high carbon CoCrMo biomedical alloy in simulated body fluids by electrochemical impedance spectroscopy

The corrosion and tribocorrosion behaviour of a high carbon CoCrMo alloy sliding against alumina in simulated body fluids under potentiostatic conditions was investigated. The electrochemical behaviour of the sample in two electrolytes at different potentials (−1 V_Ag/AgCl, −0.5 V_Ag/AgCl, +0.05 V_Ag/AgCl, +0.5 V_Ag/AgCl and +0.75 V_Ag/AgCl) was studied by means of electrochemical impedance spectroscopy (EIS). The effects of solution chemistry and applied potential on the wear volume and anodic current were determined. Result shows that wear of CoCrMo alloy is negligible under cathodic and in the cathodic-anodic transition and considerably increases in the passive domain. Third body behaviour depends on surface chemistry which also varied depending on solution chemistry and electrochemically applied potential thus, modifies the tribocorrosion rate of CoCrMo alloy.     

Arsenic species interactions with a porous carbon electrode as determined with an electrochemical quartz crystal microbalance

The interactions of arsenic species with platinum and porous carbon electrodes were investigated with an electrochemical quartz crystal microbalance (EQCM) and cyclic voltammetry in alkaline solutions. It is shown that the redox reactions in arsenic-containing solutions, due to arsenic reduction/deposition, oxidation/desorption, and electrocatalyzed oxidation by Pt can be readily distinguished with the EQCM. This approach was used to show that the arsenic redox reactions on the carbon electrode are mechanistically similar to that on the bare Pt electrode. This could not be concluded with just classical cyclic voltammetry alone due to the obfuscation of the faradaic features by the large capacitative effects of the carbon double layer.For the porous carbon electrode, a continual mass loss was always observed during potential cycling, with or without arsenic in the solution. This was attributed to electrogasification of the carbon. The apparent mass loss per cycle was observed to decrease with increasing arsenic concentration due to a net mass increase in adsorbed arsenic per cycle that increased with arsenic concentration, offsetting the carbon mass loss. Additional carbon adsorption sites involved in arsenic species interactions are created during electrogasification, thereby augmenting the net uptake of arsenic per cycle.It is demonstrated that EQCM, and in particular the information given by the behavior of the time derivative of the mass vs. potential, or massogram, is very useful for distinguishing arsenic species interactions with carbon electrodes. It may also prove to be effective for investigating redox/adsorption/desorption behavior of other species in solution with carbon materials as well.     

Investigation of interfacial processes at tetraruthenated zinc porphyrin films using electrochemical surface plasmon resonance and electrochemical quartz crystal microbalance

In the present work we describe the investigation of interfacial and superficial processes on tetraruthenated zinc porphyrin (ZnTRP) films immobilized on gold electrode surface. In situ and real time measurements employing electrochemical surface plasmon resonance (ESPR) and electrochemical quartz crystal microbalance (EQCM) have given new insights into the electrochemical oxidation of ferrocyanide and phenolic compounds (acetaminophen, dopamine, and catechol) on ZnTRP modified electrodes. The decrease of diode like behavior in the presence of such phenolic species in contrast with ferrocyanide was clearly assigned to the inclusion of those species in the porphyrin film, creating new conduction pathways connecting the gold electrode surface with the film/solution interface. In fact, there are evidences that they can intercalate in the film (catechol > dopamine > acetaminophen), whereas ferrocyanide is completely excluded. Accordingly, the molecular size may play a fundamental role in such a process.     

Electrochemical quartz crystal microbalance study of formation and redox transformations of poly(diphenylamine)

The electropolymerization of diphenylamine (DPA) dissolved in 2 mol dm⁻³ H₂SO₄ has been studied on a gold electrode by cyclic electrochemical quartz crystal microbalance measurements. Similar experiments have been accomplished with DPA microcrystals attached to a gold electrode, in the presence of aqueous acidic media. In both cases the redox transformations of the poly(diphenylamine) films formed on Au have been investigated in solutions of different pHs. The cyclic voltammograms and the mass changes refer to two closely spaced redox reactions resulting in the formation of cation radicals and dications, respectively. The irregular, broad shape of the voltammetric waves may be explained by presence of other electrochemically active sites beside the linear diphenylbenzidine structure. The results indicate a pH and potential-dependent relative contribution of anions and hydrogen ions to the overall ion exchange process. The expulsion of protons is the predominant ion transport process at the beginning of the oxidation and the incorporation of anions occurs at a later stage of oxidation. The sorption/desorption of solvent molecules also contributes to the mass change observed during the redox transformations of the polymer.     

Ion exchange properties of polypyrrole studied by electrochemical quartz crystal microbalance (EQCM)

The electrochemical polymerization of pyrrole in aqueous solution was studied as a function of a variety of parameters, such as magnitude of current density and monomer concentration. The possibility of quantitative replacement of counterions by solution anions was studied in detail using the electrochemical quartz crystal microbalance (EQCM) technique. It was found that the polymer structure can be manipulated, even after synthesis. The manipulation was revealed to be dependent on various factors, including the nature of the counterion and of the electrolyte concentration. On the basis of these observations, a two-layer structure is suggested for polypyrrole-based polymers. © 1999 Society of Chemical Industry     

Electrochemical behavior of thin polycrystalline rhodium layers studied by cyclic voltammetry and quartz crystal microbalance

Electrochemical behavior of thin polycrystalline Rh layers has been studied in 0.5 M H₂SO₄ solution by cyclic voltammetry (CV) and the electrochemical quartz crystal microbalance (EQCM). The properties of surface oxide formed on freshly electrodeposited Rh are different than on electrochemically aged Rh. The analysis of frequency changes in both hydrogen and oxygen regions is presented. It is suggested that hydrogen desorption occurs simultaneously with the adsorption of HSO₄⁻ ions, whose maximum surface coverage reaches ca. 8%. The EQCM results indicate that RhO is the main species formed during Rh surface oxidation. Metal dissolution proceeds during electrode cycling to sufficiently high potentials. The amount of dissolved metal increases with an increase in potential and a decrease in scan rate.     

A quartz crystal microbalance study of the kinetics of interaction of benzotriazole with copper

The kinetics of interaction of benzotriazole (C₆H₅N₃, BTAH) with the surface of copper in salt water were studied using an electrochemical quartz crystal microbalance and X-ray photoelectron spectroscopy (XPS). Upon injecting BTAH into the electrolyte, three regions appear in the time response of the microbalance. Region I (at short time of few minutes), exhibits rapid linear growth of mass with time, which is attributed to the formation of a protective Cu(I)BTA complex. Region II reveals attachment of BTAH at a slower rate onto the inner Cu(I)BTA complex. Region III is a plateau indicating that the BTAH film attains an equilibrium mass and thickness, which increase with the concentration of BTAH. The intensity of the N1s peak in the XPS spectra increases with the time of immersion, indicating more BTAH on the surface. The results suggest a duplex inhibitor film composed of an inner thin layer of Cu(I)BTA and an outer layer of physically adsorbed BTAH which increases in thickness with time and BTAH concentration. They also offer an explanation for the much documented findings of simultaneous increase of the polarization resistance and decrease of double layer capacity with inhibitor concentration and time of immersion.     

Electrochemical quartz crystal microbalance study of redox transformations of TCNQ microcrystals in concentrated LiCl solutions

Microcrystals of 7,7,8,8-tetracyanoquinodimethane (TCNQ) immobilized on gold surface have been investigated by combined cyclic voltammetry/chronoamperometry and piezoelectric nanogravimetry at an electrochemical quartz crystal microbalance (EQCM) in dilute and concentrated LiCl solutions. It is proved that TCNQ microcrystals even when TCNQ is reduced to its highly soluble Li⁺TCNQ⁻ salt can be studied in aqueous solutions when the water activity is decreased to a low level. At high electrolyte concentrations the voltammetric and chronoamperometric responses obtained for TCNQ microcrystals show the theoretically predicted pattern characteristic to the solid-solid phase transformation under the control of the nucleation and growth kinetics. The utilization of the idea presented in this work, i.e., using electrolyte of high concentrations (or decreasing the water activity by adding an indifferent component to the liquid phase in high concentration) can open up new vistas in the study of redox transformations of immobilized microcrystals which are soluble in water.     

Data correction technique for using common electrochemical apparatus for the measurement of crystal impedance

Crystal impedance (CI) is a well-known technique which extends the capabilities of the quartz crystal microbalance (QCMB) technique by refining the apparent mass change reported by QCMB resonance frequency measurements into a corrected mass change and an energy loss or dissipation component. In addition to mass change, the energy loss component can provide information about additional sample properties, such as surface rigidity or roughness, as well as the viscoeleastic properties of the medium in which measurements are performed. Previous reports of CI measurements involve the use of a network analyzer, an instrument not commonly found in an electrochemical research group. Here, we describe how to utilize a more common electrochemical impedance spectroscopy (EIS) system with sufficient bandwidth for the purpose of collecting CI data. Specifically, we discuss the measurement setup required to minimize impedance mismatch and a means of mathematically correcting for the impedance of the measurement system itself. We demonstrate the utility of this system using the CI response of a Pt-coated crystal to D-fructose solutions with known density and viscosity.     

Adsorption of bovine serum albumin and fibrinogen on hydrophilicity-controllable surfaces of polypyrrole doped with dodecyl benzene sulfonate—A combined piezoelectric quartz crystal impedance and electrochemical impedance study

Combined measurements of piezoelectric quartz crystal impedance (PQCI) and electrochemical impedance (EI) were utilized to monitor in situ adsorption of two proteins (bovine serum albumin and fibrinogen) onto the hydrophilicity-controllable surfaces of polypyrrole (PPY) doped with dodecyl benzene sulfonate (DBS). Three of these polymer films, PPY/DBS-I, PPY/DBS-II and PPY/DBS-III, were obtained by galvanostatic electropolymerization of pyrrole in aqueous solutions containing 0.6, 1.2 and 2.0 mmol L⁻¹ sodium dodecyl benzene sulfonate (SDBS), respectively. The PPY/DBS-II obtained from electropolymerization of pyrrole in the presence of 1.2 mmol L⁻¹ SDBS (the critical micelle concentration of SDBS in aqueous solution, CMC) exhibited the greatest hydrophobicity, as suggested by contact angle measurement. And the saturation-adsorption amounts for both proteins were found to be greatest on the surface. The kinetics and adsorption mechanisms of both proteins adsorbed on these three surfaces were discussed. Langmuir and Freundlich models were used for explaining the adsorption behavior of proteins, giving that Langmuir model is better for bovine serum albumin (BSA) and both model are not so available for fibrinogen.     

Mechanistic study of the reduction of copper oxides in alkaline solutions by electrochemical impedance spectroscopy

Electrochemical impedance spectroscopy was used to study the mechanism by which copper oxides are reduced in alkaline solutions. For the reductions of CuO and Cu₂O, a capacitive loop and also an inductive loop under certain conditions were observed in the complex plane. The electrochemical impedance for CuO reduction was not greatly dependent on the solution alkalinity and the kind of alkali hydroxide. However, the electrochemical impedance for Cu₂O reduction was considerably affected by the kind and concentration of alkali hydroxide. The diameter of the capacitive loop, i.e., the charge-transfer resistance (R_ct), was increased with increase in solution alkalinity. It should also be noted that R_ct was increased in the order of KOH < NaOH < LiOH. These dependences were consistent with the good separation between the reduction potentials of CuO and Cu₂O in chronopotentiometric and voltammetric measurements with strongly alkaline electrolytes containing Li⁺. The inductive loop observed for the Cu₂O reduction at higher concentrations of KOH (>6 M) and LiOH (>0.2 M) suggested the existence of an intermediate species (probably CuOH). The specific inhibitory effect of Li⁺ ions on the reduction of Cu₂O might be explained by a possible stabilization of CuOH by Li⁺ ions.     

Electrodeposition of CdS from acidic aqueous thiosulfate solution—Invesitigation of the mechanism by electrochemical quartz microbalance technique

Electrochemical quartz crystal microbalance was used to study mechanism of cathodic electrodeposition of CdS from acidic aqueous solutions containing 0.01 M Cd(ClO₄)₂ and 0.1 M Na₂S₂O₃ as a source of sulfur. Experiments were performed by means of cyclic voltammetry and potentiostatic method. A comparison of gravimetric and current responses at pH 3 and 4 allowed for determination of the potential range in which side reactions of reduction of SO₃²⁻ and H⁺ ions compete most strongly with formation of CdS. The film thickness was determined by means of two methods: from AFM profiles and EQCM measurements.     

Influence of ultrasound irradiation on the adsorption of bovine serum albumin on copper

The effect of irradiation by power ultrasound on the adsorption of proteins on copper has been investigated, using bovine serum albumin (BSA) as a model protein in pH 7 phosphate buffer solution. Open circuit potential measurements, cyclic voltammetry and electrochemical impedance spectroscopy were used to characterise the copper/solution interface. Electrochemical impedance measurements at potentials close to the open circuit potential showed that pulsed ultrasound irradiation removes the naturally formed copper oxide films in phosphate buffer solution, and that their re-formation can lead to an oxide film with different electrical characteristics. Adsorption of BSA blocks the surface, decreasing or increasing the interfacial resistance, depending on the applied potential and the oxide characteristics, as well as changing the interfacial capacitance. This study augurs well for application of the combination of electrochemical impedance plus ultrasound to other systems. Special issue dedicated to Prof. Tony Wragg.     

利用石英晶体微量天平测定紫杉醇在二氧化碳中的溶解度

A quartz crystal microbalance (QCM) is used to determine the phase equilibrium of paclitaxel-carbon dioxide system in the pressure range of 0-11 MPa and at temperatures of 35 °C,40 °C and 45 °C.The experimental results indicated that gaseous CO2 could be absorbed poorly into paclitaxel.The swelling of paclitaxel film in CO2 was observed before paclitaxel dissolved into supercritical carbon dioxide (ScCO2) with the increase of pressure.It was found that ScCO2 was not a good solvent for paclitaxel.The mole fraction of paclitaxel in ScCO2 was in the range of (4.5×10-9)-(7.8×10-9) under all our experimental conditions.Therefore,a much higher pressure than the CO2 supercritical point and/or a cosolvent must be used in any processes wherever paclitaxel dissolution in ScCO2 is required.     

石英晶体微天平(QCM)在超临界CO2过程中的应用

超临界流体技术是绿色化学的一个重要领域,由于高压的限制,传统检测手段很难应用于过程中涉及的物理和化学性质数据的测定,严重影响了超临界技术的研究与应用。石英晶体微天平(QCM)作为一种新型的介观级微称重技术,适用于高温高压等极端条件,具有测量精度高的优点。本文介绍了石英晶体微天平技术应用的基本理论及其特点,并重点回顾和展望了该技术在超临界CO2中的应用。     

Electrodeposition of copper from spent Li-ion batteries by electrochemical quartz crystal microbalance and impedance spectroscopy techniques

Information about the copper electrodeposition mechanism at different pH values was obtained using an electrochemical quartz crystal microbalance (EQCM) technique, as well as potentiodynamic, potentiostatic, and electrochemical impedance spectroscopy (EIS) techniques. In agreement with the measurements obtained from the EQCM and potentiostatic experiments, an intermediate Cu⁺ species and a CuO layer are formed. Simultaneous mechanism of direct reduction of Cu²⁺ and copper oxide (CuO) reduction at pH 2.0 and 4.5 occur. The EIS experiment shows a diffusion-controlled process by the presence of a Warburg element, a CPE related to the irregular metallic copper electrodeposition, and a resistance of the electrodeposit.     

Investigation of cobalt deposition using the electrochemical quartz crystal microbalance

Electrodeposition of cobalt from sulfate solutions at different pH values was investigated using the EQCM technique coupled with cyclic voltammetry. The results show that cobalt hydroxide is formed simultaneously with cobalt deposition during the early stages of reduction due to the pH variation near the electrode surface caused by the parallel hydrogen evolution reaction (HER). This result was confirmed using M/z values calculated using the Sauerbrey equation and Faraday's law, which showed the presence of cobalt hydroxide in the electrodeposits. A flux model was developed and it assumes a direct reduction of cobalt, simultaneous HER and the formation of cobalt hydroxide during the early stages of deposition at pH 4.10. When the solution pH is decreased to 3.33 only the direct cobalt reduction is observed without any hydroxylated species formation.