The electrocatalytic behavior of Ru0.8Co0.2O2−x—the effect of particle shape and surface composition

The electrocatalytic activity of Ru_0.8Co_0.2O_2−x nanocrystals was studied using diffraction, microscopic and spectroscopic techniques to elucidate the role of particle shape and surface chemical composition in the electrocatalytic evolution of oxygen and chlorine. The prepared Ru_0.8Co_0.2O_2−x samples are of the rutile structure, their chemical composition, however, differs. The samples with the smallest particle size compensate for the Co doping by oxygen deficiency. The materials featuring bigger particle size show tendency to compensate for the presence of cobalt by higher valency of Ru. Regardless of the particle size or actual surface composition of the Ru_0.8Co_0.2O_2−x electrodes, the chlorine evolution precedes that of oxygen by ca. 100 mV. The Ru_0.8Co_0.2O_2−x electrodes retain high affinity to oxygen evolution once the reaction becomes possible. This behavior can be ascribed to a stabilization of the six-valent ruthenium, which represents the major intermediate for the oxygen evolution process, at the electrode surface due to the presence of di-valent and tri-valent cobalt. This effect precludes the possible effects of the particle shape and crystal edge distribution.     

Oxygen reduction reaction on electrodeposited Pt100−x−yNixPdy thin films

The kinetics of the oxygen reduction reaction (ORR) were examined on a series of Pt_100−x−yNi_xPd_y ternary alloys. Films were produced by electrodeposition that involved a combination of underpotential and overpotential reactions. For Pt-rich Pt_100−x−yNi_xPd_y alloy films (x < 0.65) Ni co-deposition occurred at underpotentials while for Ni-rich films (x > 0.65) deposition proceeded at overpotentials. Rotating disk electrode (RDE) measurements of the ORR kinetics on Ni-rich Pt_100−x−yNi_xPd_y thin films revealed up to ∼6.5-fold enhancement of the catalytic activity relative to Pt films with the same Pt mass loading. More than half of the electrocatalytic gain may be attributed to surface area expansion due to Ni dealloying. Surface area normalization based on the H_upd charge reduced the enhancement factor to a value less than 2. The most active ternary alloy film for ORR was Pt₂₅Ni₇₃Pd₂. Comparison of the ORR on Pt, Pt₂₀Ni₈₀, Pt₂₅Ni₇₃Pd₂ thin films indicate that the binary alloy is the most active with a H_upd normalized ORR enhancement factor of up to 3.0 compared to 1.6 for the ternary alloy.     

Oxygen and chlorine evolution on RuO2 + TiO2 + CeO2 + Nb2O5 mixed oxide electrodes

A systematic investigation was conducted on the mechanism and electrocatalytic properties of O₂ and Cl₂ evolution on mixed oxide electrodes of nominal composition: Ti/[Ru_(0.3)Ti_(0.6)Ce_(0.1−x)]O₂[Nb₂O₅]_(x) (0 ≤ x ≤ 0.1). For the oxygen evolution, a 30 mV Tafel slope is obtained in the presence of CeO₂, while in its absence a 40 mV coefficient is observed. The intrinsic electrocatalytic activity is mainly due to electronic factors, as result of the synergism between Ru and Ce oxides. For chlorine evolution, the Tafel slope (30 mV) is independent on oxide composition. The best global electrocatalytic activity for ClER was observed in the absence of Nb₂O₅ additive. Variation of the voltammetric charge throughout the experiments confirms high CeO₂ content compositions are fragile, due mainly to the porosity caused by CeO₂ presence. On the other hand, Nb₂O₅ addition decreases considerably this instability.     

Ni1−xCox/YSZ cermet anodes for solid oxide fuel cells

Nanocrystalline and homogeneous powder mixtures of (Ni_1−xCo_xO_y)+YSZ were obtained by combustion synthesis, and reduced in H₂ at 800 °C to obtain Ni_1−xCo_x/YSZ cermets, and three layer symmetrical cells cermet/YSZ/cermet. These three layer cells were co-firing at 1450 °C, and then reduced to obtain porous Ni_1−xCo_x/YSZ cermet layers with good adhesion to the electrolyte. Results obtained under OCV show that partial substitution of Ni with Co lowers the polarisation resistance, especially the main contribution which is usually most dependent on the cermets microstructure. This trend is reverted for high fractions of Co, and the polarisation resistance obtained for Co/YSZ cermets is much higher than for Ni/YSZ. The low frequency contribution of the polarisation resistance was mainly dependent on the partial pressures of H₂ and H₂O, and is less dependent on the substitution of Ni with Co.     

Improvement of electrochemical properties of Li[Ni0.4Co0.2Mn(0.4−x)Mgx]O2−yFy cathode materials at high voltage region

Spherical Li[Ni_0.4Co_0.2Mn_(0.4−x)Mg_x]O_2−yF_y (x = 0, 0.04, y = 0, 0.08) with phase-pure and well-ordered layered structure have been synthesized by heat-treatment of spherical [Ni_0.4Co_0.2Mn_0.4−xMg_x]₃O₄ precursors with LiOH·H₂O and LiF salts. The average particle size of the powders was about 10-15 μm and the size distribution was quite narrow due to the homogeneity of the metal carbonate, [Ni_0.4Co_0.2Mn_(0.4−x)Mg_x]CO₃ (x = 0, 0.04) precursors. Although the Li[Ni_0.4Co_0.2Mn_0.36Mg_0.04]O_1.92F_0.08 delivered somewhat slightly lower initial discharge capacity, however, the capacity retention, interfacial resistance, and thermal stability were greatly enhanced comparing to the Li[Ni_0.4Co_0.2Mn_0.4]O₂ and Li[Ni_0.4Co_0.2Mn_0.36Mg_0.04]O₂.     

Evolution of the local structure and electrochemical properties of spinel LiNixMn2−xO4 (0 ≤ x ≤ 0.5)

A series of Ni substituted spinel LiNi_xMn_2−xO₄ (0 ≤ x ≤ 0.5) have been synthesized to study the evolution of the local structure and their electrochemical properties. X-ray diffraction showed a few Ni cations moved to the 8a sites in heavily substituted LiNi_xMn_2−xO₄ (x ≥ 0.3). X-ray photoelectron spectroscopy confirmed Ni²⁺ cations were partially oxidized to Ni³⁺. The local structures of LiNi_xMn_2−xO₄ were studied by analyzing the and A_1g Raman bands. The most compact [Mn(Ni)O₆] octahedron with the highest bond energy of Mn(Ni)O was found for LiNi_0.2Mn_1.8O₄, which showed a Mn(Ni)O average bond length of 1.790 Å, and a force constant of 2.966 N cm⁻¹. Electrolyte decomposition during the electrochemical charging processes increased with Ni substitution. The discharge capacities at the 4.1 and 4.7 V plateaus obeyed the linear relationships with respect to the Ni substitution with the slopes of −1.9 and +1.9, which were smaller than the theoretical values of −2 and +2, respectively. The smaller slopes could be attributed to the electrochemical hysteresis and the presence of Ni³⁺ in the materials.     

Structural,magnetic and dielectric behavior of Mg1−xCaxNiyFe2−yO4 nano-ferrites synthesized by the micro-emulsion method

Ca–Ni co-substituted samples of nanocrystalline spinel ferrites with chemical formula Mg_1−xCa_xNi_yFe_2−y O₄ (x=0.0–0.6, y=0.0–1.2) were synthesized by the micro-emulsion method and were annealed at 700 °C for 7 h. The synthesized samples were characterized by x-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, vibrating sample magnetometry (VSM) and dielectric measurements. The XRD and FTIR analysis reveals that single phase samples can be achieved by substituting Ca and Ni ions at Mg and Fe sites respectively in cubic spinel nano-ferrites. The crystallite size of the synthesized samples was found in the range 29–45 nm. The saturation magnetization (M_s) increases from 9.84 to 24.99 emu/g up to x=0.2, y=0.4 and then decreases, while the coercivity (H_c) increases continuously from 94 to 153 Oe with the increase in dopants concentration. The dielectric properties of these nano materials were also studied at room temperature in the frequency range 100 MHz to 3 GHz. The dielectric parameters were found to decrease with the increased Ca–Ni concentration. Further the peaking behavior was observed beyond 1.5 GHz. The frequency dependent dielectric properties of all the samples have been explained qualitatively on the basis of the Maxwell–Wagner two-layer model according to Koop's phenomenological theory. The enhanced magnetic parameters and reduced dielectric properties make the synthesized materials suitable for switching and high frequency applications, respectively.     

Characterization of MgxM2 − xP2O7 (M = Cu and Ni) solid solutions

In this study, Mg_xM_2 − xP₂O₇ (M = Cu, Ni; 0 ≤ x ≤ 2) and Mg_3 − yNi_y(PO₄)₂ (0 ≤ y ≤ 3) compositions were synthesized by the chemical coprecipitation method and characterized by X-ray diffraction, UV-vis-NIR spectroscopy and CIE L* a* b* (Commission Internationale de l’Eclairage L* a* b*) parameters measurements.Solid solutions with α-Cu₂P₂O₇ and α-Ni₂P₂O₇ structures and solid solutions with Ni₃(PO₄)₂ structure were obtained from diphosphate and orthophosphate compositions respectively. Isostructurality of α-Ni₂P₂O₇ and α-Mg₂P₂O₇ structures enlarges the compositional range of solid solution formation respect to the Mg_xCu_2 − xP₂O₇ solid solutions one.The CIE L* a* b* parameters in Mg_xNi_2 − xP₂O₇ samples were obtained comparable with these parameters in others yellow materials suitable for ceramic pigments. Mg_0.5Ni_1.5P₂O₇ composition fired at 800 °C or 1000 °C is the optimal composition to obtain yellow materials with α-diphosphate structure in conditions of this study.     

Kinetics and PEMFC performance of RuxMoySez nanoparticles as a cathode catalyst

Kinetics of Ru_xMo_ySe_z nanoparticles dispersed on carbon powder was studied in 0.5 M H₂SO₄ electrolyte towards the oxygen reduction reaction (ORR) and as cathode catalysts for a proton exchange membrane fuel cell (PEMFC). Ru_xMo_ySe_z catalyst was synthesized by decarbonylation of transition-metal carbonyl compounds for 3 h in organic solvent. The powder was characterized by X-ray diffraction (XRD), and transmission electron microscopy (TEM) techniques. Catalyst is composed of uniform agglomerates of nanocrystalline particles with an estimated composition of Ru₆Mo₁Se₃, embedded in an amorphous phase. The electrochemical activity was studied by rotating disk electrode (RDE) and rotating ring-disk electrode (RRDE) techniques. Tafel slopes for the ORR remain invariant with temperature at −0.116 V dec⁻¹ with an increase of the charge transfer coefficient in dα/dT = 1.6 × 10⁻³, attributed to an entropy turnover contribution to the electrocatalytic reaction. The effect of temperature on the ORR kinetics was analyzed resulting in an apparent activation energy of 45.6 ± 0.5 kJ mol⁻¹. The catalyst generates less than 2.5% hydrogen peroxide during oxygen reduction. The Ru_xMo_ySe_z nanoparticles dispersed on a carbon powder were tested as cathode electrocatalyst in a single fuel cell. The membrane-electrode assembly (MEA), included Nafion^® 112 as polymer electrolyte membrane and commercial carbon supported Pt (10 wt%Pt/C-Etek) as anode catalyst. It was found that the maximum performance achieved for the electro-reduction of oxygen was with a loading of 1.0 mg cm⁻² Ru_xMo_ySe_z 20 wt%/C, arriving to a power density of 240 mW cm⁻² at 0.3 V and 80 °C.     

Zr-doped Li[Ni0.5−xMn0.5−xZr2x]O2 (x = 0, 0.025) as cathode material for lithium ion batteries

Layered Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) have been prepared by the mixed hydroxide and molten-salt synthesis method. The individual particles of synthesized materials have a sub-microsize range of 200-500 nm, and LiNi_0.475Mn_0.475Zr_0.05O₂ has a rougher surface than that of LiNi_0.5Mn_0.5O₂. The Li/Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) electrodes were cycled between 4.5 and 2.0 V at a current density of 15 mA/g, the discharge capacity of both cells increased during the first ten cycles. The discharge capacity of the Li/LiNi_0.475Mn_0.475Zr_0.05O₂ cell increased from 150 to 220 mAh/g, which is 50 mAh/g larger than that of the Li/LiNi_0.5Mn_0.5O₂ cell. We found that the oxidation of oxygen and the Mn³⁺ ion concerned this phenomenon from the cyclic voltammetry (CV). Thermal stability of the charged Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) cathode was improved by Zr doping.     

FexCo0.5−xNi0.5-SDC anodes for low-temperature solid oxide fuel cells

Trimetal alloys, Fe_xCo_0.5−xNi_0.5 (x = 0.1, 0.2, 0.25, 0.3, 0.4), were studied as anodes for low-temperature solid oxide fuel cells (LT-SOFCs) based on GDC (Ce_0.9Gd_0.1O_1.95) electrolytes. The alloys were formed by in situ reduction of Fe_xCo_0.5−xNi_0.5O_y composites, which were synthesized using a glycine-nitrate technique. Symmetrical cells consisted of Fe_xCo_0.5−xNi_0.5-SDC electrodes and GDC electrolytes, and single cells consisted of Fe_xCo_0.5−xNi_0.5-SDC (Ce_0.8Sm_0.2O_1.9) anodes, GDC electrolytes, and SSC (Sm_0.5Sr_0.5CoO₃)-SDC cathodes were prepared using a co-pressing and co-firing process. Interfacial polarization resistances and I-V curves of these cells were measured at temperature from 450 to 600 °C. With Fe_0.25Co_0.25Ni_0.5-SDC as anodes, the cells showed the lowest interfacial resistance and highest power density. For example, at 600 °C, the resistance was about 0.11 Ω cm² and power density was about 750 mW cm⁻² when humidified (3% H₂O) hydrogen was used as fuel and stationary air as oxidant. Further, the cell performance was improved when the molar ratio of Fe:Co:Ni approached 1:1:2, i.e. Fe_0.25Co_0.25Ni_0.5. In addition, higher power density and lower interfacial resistance were obtained for cells with the Fe_0.25Co_0.25Ni_0.5-SDC anodes comparing to that with Ni-SDC anodes, which have been usually used for LT-SOFCs. The promising performance of Fe_xCo_0.5−xNi_0.5 as anodes suggests that trimetallic anodes are worth considering for SOFCs that operate at low-temperature.     

New NiFe2−xCrxO4 spinel films for O2 evolution in alkaline solutions

Spinel-type ternary ferrites with composition NiFe_2−xCr_xO₄ (0 ≤ x ≤ 1) were synthesized by a precipitation method and their physicochemical and electrocatalytic properties have been investigated using IR, XRD, BET surface area, XPS, impedance and Tafel polarization techniques. The study indicated that substitution of Cr from 0.2 to 1.0 mol in the spinel matrix increased the apparent electrocatalytic activity of the base oxide towards the O₂ evolution reaction in 1 M KOH at 25 °C. The apparent electrocatalytic activity of the oxide with 0.8-1.0 mol Cr was found to be the greatest among the present series of oxides investigated. It is noteworthy that the electrocatalytic activity of the oxide with x = 0.8-1.0 was also greater than those of other spinel/perovskite O₂ evolving electrocatalysts reported in literature.     

MnxCu1−xCo2O4 used as bifunctional electrocatalyst in alkaline medium

Composite film electrodes containing mechanically mixed Mn_xCu_1−xCo₂O₄ (0 ≤ x ≤ 1) particles, carbon black Vulcan XC72R and poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP) were formed on the glassy carbon disk surface of a rotating ring-disk electrode (RRDE) and studied for the oxygen reduction and evolution reactions (ORR and OER, respectively) in 1 M KOH solution. The electrocatalytic activities for both reactions were observed to depend strongly on the Mn content in CuCo₂O₄. An opposite trend was observed for the apparent and intrinsic electrocatalytic activities for the ORR; the simultaneous presence of Cu and Mn was found to be detrimental to the intrinsic charge density, but beneficial to the geometric charge density with a maximum for Mn_0.6Cu_0.4Co₂O₄. The latter was characterized by the highest total number of electrons exchanged per O₂ molecule, n, close to 4, greater k₁ (4e⁻ process)/k₂ (2e⁻ process) ratios, and by a unique and low Tafel slope (−41 mV dec⁻¹). The results obtained for the OER showed that the intrinsic electrocatalytic activity is determined by the number of active sites (Co⁴⁺) electrochemically formed at the oxide surface prior to the OER, from Co³⁺ cations. The partial substitution of Cu by Mn in CuCo₂O₄ was found to decrease the OER activity.     

Characterization of Mg1−xNixAl2O4 solid solutions prepared by combustion synthesis

Mg_1−xNi_xAl₂O₄ (x = 0, 0.25, 0.5, 0.75 and 1) solid solutions have been prepared by combustion synthesis. After annealing the combustion synthesized powders at 1000 °C for 3 h single-phase Mg_1−xNi_xAl₂O₄ was obtained over the entire range of compositions. The lattice parameter of Mg_1−xNi_xAl₂O₄ gradually increased from 8.049 Å (NiAl₂O₄) to 8.085 Å (MgAl₂O₄), which certified the formation of the spinel solid solutions. All samples prepared by combustion synthesis had blue color shades, denoting the inclusion of Ni²⁺ in the spinel structure in octahedral and tetrahedral configuration. The crystallite size of Mg_1−xNi_xAl₂O₄ was in the range of 35-39 nm and the specific surface area varied between 5.8 and 7.0 m²/g.     

Amorphous Ru1−yCryO2 loaded on TiO2 nanotubes for electrochemical capacitors

Amorphous Ru_1−yCr_yO₂/TiO₂ nanotube composites were synthesized by loading different amount of Ru_1−yCr_yO₂ on TiO₂ nanotubes via a reduction reaction of K₂Cr₂O₇ with RuCl₃·nH₂O at pH 8, followed by drying in air at 150 °C. Cyclic voltammetry and galvanostatic charge/discharge tests were applied to investigate the performance of the Ru_1−yCr_yO₂/TiO₂ nanotube composite electrodes. For comparison, the performance of amorphous Ru_1−yCr_yO₂ was also studied. The results demonstrated that the three dimensional nanotube network of TiO₂ offered a solid support structure for active materials Ru_1−yCr_yO₂, allowed the active material to be readily available for electrochemical reactions, and increased the utilization of active materials. A maximum specific capacitance 1272.5 F/g was obtained with the proper amount of Ru_1−yCr_yO₂ loaded on the TiO₂ nanotubes.     

Comparative study of Li[Co1−zAlz]O2 prepared by solid-state and co-precipitation methods

Li[Co_1−zAl_z]O₂ (0 ≤ z ≤ 0.5) samples were prepared by co-precipitation and solid-state methods. The lattice constants varied smoothly with z for the co-precipitated samples but deviated for the solid-state samples above z = 0.2. The solid-state method may not produce materials with a uniform cation distribution when the aluminum content is large or when the duration of heating is too brief. Non-stoichiometric Li_x[Co_0.9Al_0.1]O₂ samples were synthesized by the co-precipitation method at various nominal compositions x = Li/(Co + Al) = 0.95, 1.0, 1.1, 1.2, 1.3. XRD patterns of the Li_x[Co_0.9Al_0.1]O₂ samples suggest the solid solution limit is between Li/(Co + Al) = 1.1 and 1.2. Electrochemical studies of the Li[Co_1−zAl_z]O₂ samples were used to measure the rate of capacity reduction with Al content, found to be about −250 ± 30 (mAh/g)/(z = 1). Literature work on Li[Ni_1/3Mn_1/3Co_1/3−zAl_z]O₂, Li[Ni_1−zAl_z]O₂ and Li[Mn_2−yAl_y]O₄ demonstrates the same rate of capacity reduction with Al/(Al + M) ratio. These studies serve as baseline characterization of samples to be used to determine the impact of Al content on the thermal stability of delithiated Li[Co_1−zAl_z]O₂ in electrolyte.     

Effect of divalent ion substitution on oxygen sensing properties of hot-spot based Eu1−xCaxBa2Cu3O7−δ and Eu1−yMgyBa2Cu3O7−δ ceramics

In this paper effects of Ca and Mg substitution on oxygen sensing properties of hot spot based Eu123 rods are reported. Eu_1−xCa_xBa₂Cu₃O_7−δ (x=0.2–0.5) and Eu_1−yMg_yBa₂Cu₃O_7−δ (y=0.2–0.5) ceramics were synthesized from oxide powders using the standard solid state method and fabricated into short rods. For Ca-substituted rods, after appearance of a visible hot spot, a constant current plateau in I–V curve was formed. The output current response of the rod in periodically changing pO₂ between 20% and 100% showed improved stability and reproducibility for x=0.4 compared to x=0.2. Improved oxygen absorption and desorption time was observed for x=0.4 compared to previously reported unsubstituted rod. On the other hand, for Mg-substituted rods the I–V behavior after formation of hot spot showed a negative slope. Faster absorption time of 3.0 s and desorption time of 6.9 s were observed for y=0.4 compared to y=0.2. The improved output current stability, reproducibility and response time is suggested to be due to changes in oxygen activation energy and increased hole concentration as a result of Ca²⁺/Mg²⁺substitutions. The Mg-substituted rods showed better performance compared to Ca-substituted rods possibly due to higher porosity and vacancy concentration.     

A novel lithium intercalation compound based on the layered structure of lithium nitridonickelates Li3−2xNixN

New lithium nickel nitrides Li_3−2xNi_xN (0.20 ≤ x ≤ 0.60) have been prepared and investigated as negative electrode in the 0.85/0.02 V potential window. These materials are prepared from a Ni/Li₃N mixture at 700 °C under a nitrogen flow. Their structural characteristics as well as their electrochemical behaviour are investigated as a function of the nickel content. For the first time are reported here the electrochemical properties of a lithium intercalation compound based on a layered nitride structure. The Li_3−2xNi_xN compounds can be reversibly reduced and oxidized around 0.5 V versus Li/Li⁺ leading to specific capacities in the range 120-160 mAh/g depending on the nickel content and the C rate. Due to a large number of lithium vacancies, the structural stability provides an excellent capacity retention of the specific capacity upon cycling.     

Synthesis and electrochemical characterization of mesoporous CoxNi1−x layered double hydroxides as electrode materials for supercapacitors

A novel nanostructured mesoporous Co_xNi_1−x layered double hydroxides (Co_xNi_1−x LDHs), which both Co(OH)₂ and Ni(OH)₂ exhibit, has been successfully synthesized by a chemical co-precipitation route using polyethylene glycol as the structure-directing reagent. Structural and morphological characterizations were performed using powder X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM). The component and thermal stability of the sample were measured by energy dispersed X-ray spectrometry (EDS), FT-IR and thermal analyses, including thermogravimetry (TG) and differential thermal analysis (DTA). Cyclic voltammogram and galvanostatic charge-discharge testified that the Co_xNi_1−x LDH has a specific capacitance of 1809 F g⁻¹ at a current density of 1 A g⁻¹ and remains at about 90.2% of the initial value after 1000 cycles at a current density of 10 A g⁻¹. The relationship between the chemical composition and the capacitance is discussed.     

Preparation and cycling performance of Aland F co-substituted compounds Li4AlxTi5−xFyO12−y

Li₄Al_xTi_5−xF_yO_12−y compounds were prepared by a solid-state reaction method. Phase analyses demonstrated that both Al³⁺ and F⁻ ions entered the structure of spinel-type Li₄Ti₅O₁₂. Charge-discharge cycling results at a constant current density of 0.15 mA cm⁻² between the cut-off voltages of 2.5 and 0.5 V showed that the Al³⁺ and F⁻ substitutions improved the first total discharge capacity of Li₄Ti₅O₁₂. However, Al³⁺ substitution greatly increased the reversible capacity and cycling stability of Li₄Ti₅O₁₂ while F⁻ substitution decreased its reversible capacity and cycling stability slightly. The electrochemical performance of the Al³⁺-F⁻-co-substituted specimen was better than the F⁻-substituted one but worse than the Al³⁺-substituted one.