Synthesis of spinel LiMn2O4 with manganese carbonate prepared by micro-emulsion method

Micro-spherical particle of MnCO₃ has been successfully synthesized in CTAB-C₈H₁₈-C₄H₉OH-H₂O micro-emulsion system. Mn₂O₃ decomposed from the MnCO₃ is mixed with Li₂CO₃ and sintered at 800 °C for 12 h, and the pure spinel LiMn₂O₄ in sub-micrometer size is obtained. The LiMn₂O₄ has initial discharge specific capacity of 124 mAh g⁻¹ at discharge current of 120 mA g⁻¹ between 3 and 4.2 V, and retains 118 mAh g⁻¹ after 110 cycles. High-rate capability test shows that even at a current density of 16 C, capacity about 103 mAh g⁻¹ is delivered, whose power is 57 times of that at 0.2 C. The capacity loss rate at 55 °C is 0.27% per cycle.     

Synthesis of highly crystalline spinel LiMn2O4 by a soft chemical route and its electrochemical performance

Highly crystalline spinel LiMn₂O₄ was successfully synthesized by annealing lithiated MnO₂ at a relative low temperature of 600 °C, in which the lithiated MnO₂ was prepared by chemical lithiation of the electrolytic manganese dioxide (EMD) and LiI. The LiI/MnO₂ ratio and the annealing temperature were optimized to obtain the pure phase LiMn₂O₄. With the LiI/MnO₂ molar ratio of 0.75, and annealing temperature of 600 °C, the resulting compounds showed a high initial discharge capacity of 127 mAh g⁻¹ at a current rate of 40 mAh g⁻¹. Moreover, it exhibited excellent cycling and high rate capability, maintaining 90% of its initial capacity after 100 charge-discharge cycles, at a discharge rate of 5 C, it kept more than 85% of the reversible capacity compared with that of 0.1 C.     

Electrochemical and ex situ XRD studies of a LiMn1.5Ni0.5O4 high-voltage cathode material

Sub-micro spinel-structured LiMn_1.5Ni_0.5O₄ material was prepared by a spray-drying method. The electrochemical properties of LiMn_1.5Ni_0.5O₄ were investigated using Li ion model cells, Li/LiPF₆ (EC + DMC)/LiMn_1.5Ni_0.5O₄. It was found that the first reversible capacity was about 132 mAh g⁻¹ in the voltage range of 3.60-4.95 V. Ex situ X-ray diffraction (XRD) analysis had been used to characterize the first charge/discharge process of the LiMn_1.5Ni_0.5O₄ electrode. The result suggested that the material configuration maintained invariability. At room temperature, on cycling in high-voltage range (4.50-4.95 V) and low-voltage range (3.60-4.50 V), the discharge capacity of the material was about 100 and 25 mAh g⁻¹, respectively, and the spinel LiMn_1.5Ni_0.5O₄ exhibited good cycle ability in both voltage ranges. However, at high temperature, the material showed different electrochemical characteristics. Excellent electrochemical performance and low material cost make this spinel compound an attractive cathode for advanced lithium ion batteries.     

Preparation and characterization of novel spinel Li4Ti5O12−xBrx anode materials

Br-doped Li₄Ti₅O₁₂ in the form of Li₄Ti₅O_12−xBr_x (0 ≤ x ≤ 0.3) compounds were successfully synthesized via solid state reaction. The structure and electrochemical properties of the spinel Li₄Ti₅O_12−xBr_x (0 ≤ x ≤ 0.3) materials were investigated. The Li₄Ti₅O_12−xBr_x (x = 0.2) presents the best discharge capacity among all the samples, and shows better reversibility and higher cyclic stability compared with pristine Li₄Ti₅O₁₂, especially at high current rates. When the discharge rate was 0.5 C, the Li₄Ti₅O_12−xBr_x (x = 0.2) sample presented the excellent discharge capacity of 172 mAh g⁻¹, which was very close to its theoretical capacity (175 mAh g⁻¹), while that of the pristine Li₄Ti₅O₁₂ was 123.2 mAh g⁻¹ only.     

Hydrothermal synthesis of LiMn2O4/C composite as a cathode for rechargeable lithium-ion battery with excellent rate capability

A spinel LiMn₂O₄/C composite was synthesized by hydrothermally treating a precursor of manganese oxide/carbon (MO/C) composite in 0.1 M LiOH solution at 180 °C for 24 h, where the precursor was prepared by reducing potassium permanganate with acetylene black (AB). The AB in the precursor serves as the reducing agent to synthesize the LiMn₂O₄ during the hydrothermal process; the excess of AB remains in the hydrothermal product, forming the LiMn₂O₄/C composite, where the remaining AB helps to improve the electronic conductivity of the composite. The contact between LiMn₂O₄ and C in our composite is better than that in the physically mixed LiMn₂O₄/C material. The electrochemical performance of the LiMn₂O₄/C composite was investigated; the material delivered a high capacity of 83 mAh g⁻¹ and remained 92% of its initial capacity after 200 cycles at a current density of 2 A g⁻¹, indicating its excellent rate capability as well as good cyclic performance.     

Characterization of structure and electrochemical properties of lithium manganese oxides for lithium secondary batteries hydrothermally synthesized from δ-KxMnO2

Lithium manganese oxides have attracted much attention as cathode materials for lithium secondary batteries in view of their high capacity and low toxicity. In this study, layered manganese oxide (δ-K_xMnO₂) has been synthesized by thermal decomposition of KMnO₄, and four lithium manganese oxide phases have been synthesized for the first time by mild hydrothermal reactions of this material with different lithium compounds. The lithium manganese oxides were characterized by powder X-ray diffraction (XRD), inductively coupled plasma emission (ICPE) spectroscopy, and chemical redox titration. The four materials obtained are rock salt structure Li₂MnO₃, hollandite (BaMn₈O₁₆) structure α-MnO₂, spinel structure LiMn₂O₄, and birnessite structure Li_xMnO₂. Their electrochemical properties used as cathode material for secondary lithium batteries have been investigated. Of the four lithium manganese oxides, birnessite structure Li_xMnO₂ demonstrated the most stable cycling behavior with high Coulombic efficiency. Its reversible capacity reaches 155 mAh g⁻¹, indicating that it is a viable cathode material for lithium secondary batteries.     

Enhanced electrochemical performances of LiNi0.5Mn1.5O4 spinel via ethylene glycol-assisted synthesis

A simple and effective method, ethylene glycol-assisted co-precipitation method, has been employed to synthesize LiNi_0.5Mn_1.5O₄ spinel. As a chelating agent, ethylene glycol can realize the homogenous distributions of metal ions at the atomic scale and prevent the growth of LiNi_0.5Mn_1.5O₄ particles. XRD reveals that the prepared material is a pure-phase cubic spinel structure (Fd3m) without any impurities. SEM images show that it has an agglomerate structure with the primary particle size of less than 100 nm. Electrochemical tests demonstrate that the as-prepared LiNi_0.5Mn_1.5O₄ possesses high capacity and excellent rate capability. At 0.1 C rate, it shows a discharge capacity of 137 mAh g⁻¹ which is about 93.4% of the theoretical capacity (146.7 mAh g⁻¹). At the high rate of 5 C, it can still deliver a discharge capacity of 117 mAh g⁻¹ with excellent capacity retention rate of more than 95% after 50 cycles. These results show that the as-prepared LiNi_0.5Mn_1.5O₄ is a promising cathode material for high power Li-ion batteries.     

Ultrasonic spray pyrolysis of nano crystalline spinel LiMn2O4 showing good cycling performance in the 3 V range

Spherical lithium manganese oxide spinel was synthesized by an ultrasonic spray pyrolysis method, and has been characterized using X-ray diffraction, scanning electron microscopy, transimission electron microscopy and electrochemical cycling at 3 V regions. The LiMn₂O₄ powders were composed of about 10 nm-sized primary particles. The delivered discharge capacity of the synthesized nano-material was 125 mAh g⁻¹ between 2.4 and 3.5 V and its retention was about 96% upon 50 cycling. From the high resolution transmission electron microscopic study, it was found that structural transition of the parent material did not occur even after the 50th electrochemical cycling on the 3 V region. It seems that the reversible structural change is possible for nanocrystalline LiMn₂O₄ as observed by the X-ray diffraction and transition electron microscopic observations.     

Niobium doped lithium titanate as a high rate anode material for Li-ion batteries

Niobium doped lithium titanate with the composition of Li₄Ti_4.95Nb_0.05O₁₂ has been prepared by a sol-gel method. X-ray diffraction (XRD) and scanning electron microscope (SEM) are employed to characterize the structure and morphology of Li₄Ti_4.95Nb_0.05O₁₂. The Li₄Ti_4.95Nb_0.05O₁₂ electrode presents a higher specific capacity and better cycling performance than the Li₄Ti₅O₁₂ electrode prepared by the similar process. The Li₄Ti_4.95Nb_0.05O₁₂ exhibits an excellent rate capability with a reversible capacity of 135 mAh g⁻¹ at 10 C, 127 mAh g⁻¹ at 20 C and even 80 mAh g⁻¹ at 40 C. Electrical resistance measurement and electrochemical impedance spectra (EIS) reveal that the Li₄Ti_4.95Nb_0.05O₁₂ exhibits a higher electronic conductivity and faster lithium-ion diffusivity than the Li₄Ti₅O₁₂, which indicates that niobium doped lithium titanate (Li₄Ti_4.95Nb_0.05O₁₂) is promising as a high rate anode for the lithium-ion batteries.     

Preparation and electrochemical performance of composite oxide of alpha manganese dioxide and Li-Mn-O spinel

Nano-sized composite powder which consisted of two manganese-based oxides, alpha manganese dioxide (α-MnO₂) and spinel Li-Mn-O, was successfully formed by intergrowth of the spinel phase inside α-MnO₂. This composite oxide was synthesized by precipitation and heat treatment in air; α-manganese dioxide powder was firstly prepared by oxidative precipitation of Mn(II) with K₂S₂O₈ in an aqueous solution, and then a mixture of the obtained manganese oxide powder and LiOH methanol solution was heat-treated in air. Electron microscopy and diffraction observations confirmed that the manganese oxide composite consisted of nano-sized grains of the spinel LiMn₂O₄ and α-MnO₂ phases. It was found that this α-MnO₂/spinel LiMn₂O₄ composite electrode exhibited highly reversible lithium insertion compared to the pristine α-MnO₂ and conventional LiMn₂O₄, that is, the composite demonstrated high discharge capacity of 148 mAh g⁻¹ as a cathode material of lithium cells in the potential range of 2.5-4.3 V with no significant capacity fading. It was thought that the intimately mixing of two oxides on a nanometer scale helped to maintain structural integrity on charge-discharge cycling, which leads to excellent capacity retention for both of the spinel and alpha-type manganese oxide.     

Crystal structure and electrochemical performance of Li3V2(PO4)3 synthesized by optimized microwave solid-state synthesis route

To investigate the crystal structure and electrochemical performance of samples synthesized under different microwave solid-state synthesis condition, a series of Li₃V₂(PO₄)₃ samples has been synthesized at five different temperatures for 3-5 min and at 750 °C for various time. The as-synthesized Li₃V₂(PO₄)₃ samples are characterized and studied by ICP-AES analysis, X-ray diffraction (XRD), Rietveld analysis, scanning and transmission electron microcopy (SEM and TEM). At relatively lower temperature (650 °C) and very short reaction time (3 min), pure phase of Li₃V₂(PO₄)₃ could be synthesized in microwave irradiation field. The crystal structure and Li atomic fractional coordinate present a significant deviation upon the change of microwave irradiation temperature and time. Relatively, the diffusion ability of lithium cations and the electrochemical performance are affected. Under the proper reaction temperature and time, the carbon-free samples MW750C5m and MW850C3m show the best specific discharge capacity 126.4 and 132 mAh g⁻¹ at the voltage range of 3.0-4.3 V, near the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹). At the voltage range of 3-4.8 V, the sample MW750C5m presents the best initial specific charge capacity of 197 mAh g⁻¹, equivalent to the reversible cycling of three lithium ions per Li₃V₂(PO₄)₃ formula unit (197 mAh g⁻¹). The initial discharge capacity, the samples MW750C5m and MW850C3m present high specific discharge capacity 183.4 and 175.7 mAh g⁻¹, respectively. The relationship among microwave irradiation condition, crystal structure, lithium atomic fractional coordinates and the electrochemical performance have been discussed in detail.     

Comparison of 4 V and 3 V electrochemical properties of nanocrystalline LiMn2O4 cathode particles in lithium ion batteries prepared by ultrasonic spray pyrolysis

Nanocrystalline LiMn₂O₄ particles were prepared by an ultrasonic spray pyrolysis method using nitrate salts at 800 °C in air atmosphere. Particle properties were characterized by the X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy. In addition, cyclic voltammetry and galvanostatic tests were performed to investigate the effects of structure on electrochemical behavior of both the 4 V and 3 V potential plateaus. Particle characterization studies show that the nanocrystalline particles have spinel structure of submicron size with spherical morphology. Particles, ranging between 75 and 1250 nm, were formed by aggregation of nanoparticles. Discharge capacity of LiMn₂O₄ particles between 3.0 and 4.5 V is 70 mA h g⁻¹ and cumulative capacity between 2.2 and 4.5 V is 111 mA h g⁻¹ at 0.5 C rate. Discharge capacity at the 4 V potential region reduces to 47% of initial capacity, whereas cumulative capacity fade is 62% after 100 cycles at 0.5 C rate. Although nanocrystalline LiMn₂O₄ cathode particles exhibit good rate capability at the 4 V plateau, capacity decreased rapidly by increasing C- rates and cycling between 2.2 and 4.5 V. The loss of capacity can be attributed to phase transformation and dissolution of electrode material. Particle characterization of used cathodes showed that nanocrystalline LiMn₂O₄ electrodes partly dissolve during electrochemical cycling.     

Spray-drying synthesized lithium-excess Li4+xTi5−xO12−δ and its electrochemical property as negative electrode material for Li-ion batteries

Li₄Ti₅O₁₂ (Fd-3m space group) materials were synthesized by controlling the lithium and titanium ratios (Li/Ti) in the range of 0.800-0.900 by using a spray-drying method, followed by calcination at several temperatures between 700 and 900 °C for large-scale production. Chemical and structure studies of the final products were done by X-ray diffraction (XRD), neutron diffraction (ND), X-ray photon electron spectroscopy (XPS), scanning electron microscopy (SEM) and inductively coupled plasma mass spectrometry (ICP-MS). The optimum synthesis condition was examined in relation to the electrochemical characteristics including charge-discharge cycling and ac impedance spectroscopy. It was found that when the spray-drying precursors at the Li/Ti ratio of 0.860 were calcined at 700-900 °C for 12 h in air, a pure Li_4+xTi_5−xO_12−δ (x = 0.06-0.08) phase with a lithium-excess composition was obtained. Based on the structural studies, it was found that the excess lithium is located at the lithium and titanium layer of the 16d site in the spinel structure (Fd-3m). These pure Li_4+xTi_5−xO_12−δ (x = 0.06-0.08) phase materials showed a higher discharge capacity of ∼164 mAh g⁻¹ at 1.55 V (vs. Li/Li⁺), between the cut-off voltage of 1.2-3.0, with an excellent cyclability and superior rate performance in comparison with the Li₄Ti₅O₁₂ phase containing impurity phases.     

Electrochemical performance of the carbon coated Li3V2(PO4)3 cathode material synthesized by a sol-gel method

A carbon coated Li₃V₂(PO₄)₃ cathode material for lithium ion batteries was synthesized by a sol-gel method using V₂O₅, H₂O₂, NH₄H₂PO₄, LiOH and citric acid as starting materials, and its physicochemical properties were investigated using X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) spectroscopy, scanning electron microscopy (SEM), energy dispersive analysis of X-ray (EDAX), transmission electron microscope (TEM), and electrochemical methods. The sample prepared displays a monoclinic structure with a space group of P2₁/n, and its surface is covered with a rough and porous carbon layer. In the voltage range of 3.0-4.3 V, the Li₃V₂(PO₄)₃ electrode displays a large reversible capacity, good rate capability and excellent cyclic stability at both 25 and 55 °C. The largest reversible capacity of 130 mAh g⁻¹ was obtained at 0.1C and 55 °C, nearly equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹). It was found that the increase in total carbon content can improve the discharge performance of the Li₃V₂(PO₄)₃ electrode. In the voltage range of 3.0-4.8 V, the extraction and reinsertion of the third lithium ion in the carbon coated Li₃V₂(PO₄)₃ host are almost reversible, exhibiting a reversible capacity of 177 mAh g⁻¹ and good cyclic performance. The reasons for the excellent electrochemical performance of the carbon coated Li₃V₂(PO₄)₃ cathode material were also discussed.     

Nanorod-assembled spinel Li1.05Mn1.95O4 rods with a central tunnel along the rod-axis for high rate capability of rechargeable lithium-ion batteries

Nanorod-assembled spinel Li_1.05Mn_1.95O₄ rods with a central tunnel along the rod-axis were synthesized using highly crystalline β-MnO₂ rods as self-templates. The synthesized spinel Li_1.05Mn_1.95O₄ is an assembly of several single crystal-like nanorods with an average diameter and length of 100 and 400 nm, respectively, which was determined by microstructural Rietveld refinement using the synchrotron powder XRD data. Galvanostatic battery testing showed that central-tunneled and nanorod-assembled Li_1.05Mn_1.95O₄ rods have a high charge storage capacity at high current densities in comparison with those of the spinel rods without a tunnel structure and commercial powders. Moreover, a capacity retention value of ∼81% was observed at the end of 100 cycles at a current of 250 mAh g⁻¹.     

Microwave solid-state synthesis and electrochemical properties of carbon-free Li3V2(PO4)3 as cathode materials for lithium batteries

Monoclinic Li₃V₂(PO₄)₃ can be rapidly synthesized at 750 °C for 5 min (MW5m) by using microwave solid-state synthesis method. The refined cell parameters and atomic coordination of the sample MW5m show some deviations compared with those of the sample synthesized in conventional solid-state synthesis method, especially the coordinate of Li atoms. Compared with the electrochemical properties of the carbon-coating sample Li₃V₂(PO₄)₃, the carbon-free sample MW5m presents well electrochemical properties. In the cut-off voltage of 3.0-4.3 V, MW5m sample presents a specific charge capacity of 132 mAh g⁻¹, almost equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹), and specific discharge capacity of 126.4 mAh g⁻¹. In the cut-off voltage of 3.0-4.8 V, MW5m shows an initial specific discharge capacity of 183.4 mAh g⁻¹ at 0.1 C, near the theoretical discharge capacity. In the cycle performance, the capacity fade of Li₃V₂(PO₄)₃ is dependent on the cut-off voltage and the preparation method, more capacity lost at relatively higher charge/discharge voltage. The reasons for the excellent electrochemical properties of Li₃V₂(PO₄)₃ rapidly synthesized in microwave field are discussed in detail.     

Influence of composite LiCl-KCl molten salt on microstructure and electrochemical performance of spinel Li4Ti5O12

A series of spinel Li₄Ti₅O₁₂ samples were synthesized via a composite molten-salt method (CMSM) using the mixtures of LiCl and KCl with different L values (L is defined as the molar ratio of LiCl:KCl) as the reaction media. It is found that the melting point of the composite molten salt can effectively influence the formation of particles, and leads to different electrochemical performances of the as-prepare Li₄Ti₅O₁₂. The investigations of X-ray diffraction (XRD), particle size distribution (PSD), Brunauer-Emmet-Teller (BET) surface area, and scanning electron microscopy (SEM) indicate that the as-prepared Li₄Ti₅O₁₂ with L = 1.5 is a pure phase, and has uniform homogeneous octahedral shape particles, rather narrow PSD, and high BET surface area. Electrochemical tests show that the optimized Li₄Ti₅O₁₂ with L = 1.5 has an initial discharge capacity of 169 mAh g⁻¹ and an initial charge-discharge efficiency of 94% at 0.2 C rate, and achieves good rate performances from 0.2 C to 5 C.     

Synthesis and electrochemical performance of Li2FeSiO4/carbon/carbon nano-tubes for lithium ion battery

Li₂FeSiO₄/carbon/carbon nano-tubes (Li₂FeSiO₄/C/CNTs) and Li₂FeSiO₄/carbon (Li₂FeSiO₄/C) composites were synthesized by a traditional solid-state reaction method and characterized comparatively by X-ray diffraction, scanning electron microscopy, BET surface area measurement, galvanostatic charge-discharge and AC impedance spectroscopy, respectively. The results revealed that the Li₂FeSiO₄/C/CNT composite exhibited much better rate performance in comparison with the Li₂FeSiO₄/C composite. At 0.2 C, 5 C and 10 C, the former composite electrode delivered a discharge capacity of 142 mAh g⁻¹, 95 mAh g⁻¹, 80 mAh g⁻¹, respectively, and after 100 cycles at 1 C, the discharge capacity remained 95.1% of its initial value.     

LiNi0.8Co0.15Al0.05O2 cathode materials prepared by TiO2 nanoparticle coatings on Ni0.8Co0.15Al0.05(OH)2 precursors

Synthesis, electrochemical, and structural properties of LiNi_0.8Co_0.15Al_0.05O₂ cathodes prepared by TiO₂ nanoparticles coating on a Ni_0.8Co_0.15Al_0.05(OH)₂ precursor have been investigated by the variation of coating concentration and annealing temperature. TiO₂-coated cathodes showed that Ti elements were distributed throughout the particles. Among the coated cathodes, the 0.6 wt% TiO₂-coated cathode prepared by annealing at 750 °C for 20 h exhibited the highest reversible capacity of 176 mAh g⁻¹ and capacity retention of 92% after 40 cycles at a rate of 1C (=190 mA g⁻¹). On the other hand, an uncoated cathode showed a reversible first discharge capacity of 186 mAh g⁻¹ and the same capacity retention value to the TiO₂-coated sample at a 1C rate. However, under a 1C rate cycling at 60 °C for 30 cycles, the uncoated sample showed a reversible capacity of 40 mAh g⁻¹, while a TiO₂-coated one showed 71 mAh g⁻¹. This significant improvement of the coated sample was due to the formation of a possible solid solution between TiO₂ and LiNi_0.8Co_0.15Al_0.05O₂. This effect was more evident upon annealing the charged sample while increasing the annealing temperature, and at 400 °C, the coated one showed a more suppressed formation of the NiO phase from the spinel LiNi₂O₄ phase than the uncoated sample.     

The preparation and characterization of Li4Ti5O12/carbon nano-tubes for lithium ion battery

Li₄Ti₅O₁₂/carbon nano-tubes (CNTs) composite was prepared by sol-gel method while Ti(OC₄H₉)₄, LiCH₃COO·2H₂O and the n-heptane containing CNTs were used as raw materials. The characters of Li₄Ti₅O₁₂/CNTs composite were determined by XRD, SEM, and TG methods. Its electrochemical properties were measured by charge-discharge cycling and impedance tests. It was found that the prepared Li₄Ti₅O₁₂/CNTs presented an excellent rate capability and capacity retention. At the charge-discharge rate of 5C and 10C, its discharge capacities were 145 and 135 mAh g⁻¹, respectively. After 500 cycles at 5C, the discharge capacity retained as 142 mAh g⁻¹. It even could be cycled at the rate of 20C. The excellent electrochemical performance of Li₄Ti₅O₁₂/CNTs electrode could be attributed to the improvement of electronic conductivity by adding conducting CNTs and the nano-size of Li₄Ti₅O₁₂ particles in the Li₄Ti₅O₁₂/CNTs composite.