Electrochemical behavior of ionically crosslinked polyampholytic gel electrolytes

An ionic complex of anionic and cationic monomers was obtained by protonation of (N,N-diethylamino)ethylmethacrylate (DEA) with acrylic acid (AAc). Free radical copolymerization of the ionic complex and acrylamide (AAm), yielded the ionically crosslinked polyampholytic gel electrolytes [poly(AAc-DEA-AAm), designated as PADA] using two types of organic solvents containing a lithium salt. The PADA gel electrolyte exhibited good thermal stability shown by the DSC thermogram. The impedance analysis at temperatures ranging from −30 to 75 °C indicated that the ionic conductivities of the PADA gel electrolytes were rather close to those of liquid electrolytes. The temperature dependence of the ionic conductivities was found to be in accord with the Arrhenius equation. Moreover, the ionic conductivities of PADA gel electrolytes increased with an increase of the molar ratios of cationic/anionic monomers. The ionic conductivities of PADA gels prepared in solvent mixtures of propylene carbonate, ethyl methyl ether and dioxolane (3:1:1, v/v) were higher than those of PADA gels prepared in propylene carbonate only. Significantly, the ionic conductivities of two kinds of PADA gel electrolytes were in the range of 10⁻³ and 10⁻⁴ S cm⁻¹ even at −30 °C. The electrochemical windows of PADA gel electrolytes measured by cyclic voltammetry were in the range from −1 V to 4.5 V.     

A study on polyurethane/acrylate crosslinked gel polymer electrolytes

2,4‐Toluene diisocyanate, poly(propylene glycol), poly(ethylene glycol) (PEG) and 2‐hydroxyethyl methacrylate were used to synthesize PEG–UA (urethane acrylate) monomer. The crosslinked polymer and gel polymer electrolytes were prepared in dioxane by free radical polymerization. The swelling behaviour, thermal degradation properties, morphology and ionic conductivity of the gel polymer electrolytes were investigated. With decrease in the proportion of dioxane used, the synthesized polymer's network density increased, its affinity with a solution of 1 M LiClO₄ in propylene carbonate (PC) decreased, and more microgel which diffused in the network. At the same time, the conductivity increased and reached 4 × 10^?4 S cm^?1 at 25 °C. Copyright © 2003 Society of Chemical Industry     

Ionically conductive polymer gel electrolytes consisting of crosslinked methacrylonitrile and organic electrolyte

To develop a highly ion‐conductive polymer electrolyte, we copolymerized methacrylonitrile (MAN) with ethylene glycol dimethacrylate (EGDMA) in propylene carbonate that contained tetraethylammonium tetrafluoroborate (TEATFB), changing the TEATFB concentration and the MAN/EGDMA molar ratio. We characterized the obtained polymer gel electrolytes with complex impedance analysis and cyclic voltammetry, intending to apply them to electric double‐layer capacitors. The ionic conductivities of the polymer gel electrolytes were dependent on the TEATFB concentration, the temperature, and particularly the crosslinking degree. The polymer gel electrolytes in this system exhibited high room‐temperature conductivities (>10^?3 S/cm). Furthermore, these polymer electrolytes showed good electrochemical stability windows ranging from ?4.0 to +4.0 V versus Ag. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2655–2659, 2002     

Composite polymer electrolytes based on the low crosslinked copolymer of linear and hyperbranched polyurethanes

Low crosslinked copolymer of linear and hyperbranched polyurethane (CHPU) was prepared, and the ionic conductivities and thermal properties of the composite polymer electrolytes composed of CHPU and LiClO₄ were investigated. The FTIR and Raman spectra analysis indicated that the polyurethane copolymer could dissolve more lithium salt than the corresponding polymer electrolytes of the non crosslinked hyperbranched polyurethane, and showed higher conductivities. At salt concentration EO/Li = 4, the electrolyte CHPU30‐LiClO₄ reached its maximum conductivity, 1.51 × 10^?5 S cm^?1 at 25°C. DSC measurement was also used for the analysis of the thermal properties of polymer electrolytes. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 3607–3613, 2007     

Overpotentials and solid electrolyte interphase formation at porous graphite electrodes in mixed ethylene carbonate-propylene carbonate electrolyte systems

The first electrochemical lithium insertion was characterized for several graphite materials with high degree of crystallinity, different particle size distributions and surface morphologies in an ethylene carbonate (EC)/propylene carbonate (PC) electrolyte. For coarser graphite materials and graphites with a low superficial defect concentration, an irreversible process was observed which correlated with the electrochemical exfoliation of graphite. Different natural and synthetic graphites with similar particle size distribution and active surface area showed differences in the passivation behavior during the first electrochemical reduction. The fraction of graphite particles exfoliating during the first galvanostatic lithium insertion linearly increased with length of the irreversible plateau, which concomitantly moved to more positive potentials. This behavior can be rationalized when considering, besides the surface structure, local overpotentials for the solid electrolyte interphase formation process, and especially the overpotential distribution through the graphite electrode. These overpotentials cause a distribution of the local current density attributed to the passivation process. Optimizing the particle contacts in the electrode by applying mechanical pressure or by selecting the proper binder decreased the overpotentials and suppressed the graphite exfoliation in the EC/PC electrolyte. Therefore, both graphite surface structure and electrode engineering aspects have to be considered for successful passivation against exfoliation.     

Ionic properties of non-aqueous liquid and PVDF-based gel electrolytes containing a cesium thiolate/disulfide redox couple

Liquid electrolytes containing a cesium thiolate/disulfide redox couple, prepared from 5-mercapto-1-methyltetrazole cesium salt (CsT) and di-5-(1-methyltetrazole)disulfide (T₂) dissolved in several aprotic solvents and solvent mixtures, have been studied using various techniques. FTIR spectroscopy reveals that relatively strong interactions occur between the reduced species T⁻ and DMSO or DMF while Cs⁺ ions are very weakly coordinated to the SO or CO bond. It is shown that the electrolyte consisting of 1.55 mol kg⁻¹ CsT in the solvent mixture DMSO/DMF (40/60%) exhibits the highest conductivity (1.1×10⁻² and 2.3×10⁻² S cm⁻¹ at 23 and 80 °C, respectively), and that the presence of the oxidized species T₂ does not affect significantly its electrical properties up to a CsT:T₂ molar ratio of 5:1. Conductivity values as a function of salt concentration are discussed in terms of the effective number of charge carriers, taking into account the level of ionic association, and of the ionic mobility. Optically transparent gel electrolytes have been prepared by incorporation of the optimal liquid electrolyte into various amounts of poly(vinylidene fluoride) (PVDF). It is shown that ionic mobility is not much affected by the polymer concentration, suggesting that migration of ions occurs mainly through the solvent mixture surrounded by the PVDF matrix.     

Nanocomposite polymer electrolyte comprising PEO/LiClO4 and solid super acid: effect of sulphated-zirconia on the crystallization kinetics of PEO

A novel PEO-based nanocomposite polymer electrolyte is prepared by using solid super acid sulphated-zirconia (, SZ) as the filler. Polarized optical microscopy (POM) and differential scanning calorimeter (DSC) results show that part of SZ particles may act as the nucleus of PEO spherulites and thus increase the amount of PEO spherulites. On the other hand, other SZ particles, which do not act as the nucleus, can restrain the recrystallization tendency of PEO chains through Lewis acid-base interaction and hence decrease the growth speed of PEO spherulites. As a result, the PEO component in PEO-LiClO₄-SZ can maintain a high amorphous state for a long time. The room temperature ionic conductivity of PEO-LiClO₄-SZ is relative high and stable compared with pristine PEO-LiClO₄, indicating that it is promising for all solid-state rechargeable lithium ion batteries.     

用于锂离子电池的改性凝胶聚合物电解质

综述了凝胶聚合物电解质的性能影响因素和改性方法;着重介绍了无机纳米粒子掺杂改性;论述了近年来离子液体在聚合物电解质方面的应用;展望了凝胶聚合物电解质的发展及应用前景。     

Bifunctional poly(ethylene glycol) based crosslinked network polymers as electrolytes for all‐solid‐state lithium ion batteries

Polymer electrolyte based lithium ion batteries represent a revolution in the battery community due to their intrinsic enhanced safety, and as a result polymer electrolytes have been proposed as a replacement for conventional liquid electrolytes. Herein, the preparation of a family of crosslinked network polymers as electrolytes via the ‘click‐chemistry’ technique involving thiol‐ene or thiol‐epoxy is reported. These network polymer electrolytes comprise bifunctional poly(ethylene glycol) as the lithium ion solvating polymer, pentaerythritol tetrakis (3‐mercaptopropionate) as the crosslinker and lithium bis(trifluoromethane)sulfonimide as the lithium salt. The crosslinked network polymer electrolytes obtained show low T_g, high ionic conductivity and a good lithium ion transference number (ca 0.56). In addition, the membrane demonstrated sterling mechanical robustness and high thermal stability. The advantages of the network polymer electrolytes in this study are their harmonious characteristics as solid electrolytes and the potential adaptability to improve performance by combining with inorganic fillers, ionic liquids or other materials. In addition, the simple formation of the network structures without high temperatures or light irradiation has enabled the practical large‐area fabrication and in situ fabrication on cathode electrodes. As a preliminary study, the prepared crosslinked network polymer materials were used as solid electrolytes in the elaboration of all‐solid‐state lithium metal battery prototypes with moderate charge–discharge profiles at different current densities leaving a good platform for further improvement. © 2018 Society of Chemical Industry     

N-Butyl-N-methylmorpholinium bis(trifluoromethanesulfonyl)imide–PVdF(HFP) gel electrolytes

Ionic liquid–polymer gels were prepared by incorporating N-butyl-N-methylmorpholinium bis(trifluoromethanesulfonyl)imide (Mor_1,4TFSI) and poly(vinylidene fluoride)–hexafluoropropylene copolymer (PVdF(HFP)) using three different methods in order to observe the variation of ionic conductivities according to the presence of propylene carbonate (PC) and various weight ratios between Mor_1,4TFSI and gel polymer electrolyte (GPE). Ionic conductivities for each gel polymer electrolyte were measured with increasing temperature. Ionic conductivities of the GPEs increased with increasing temperature and weight ratio of Mor_1,4TFSI. In addition, the addition of PC into GPE led to the improvement of ionic conductivities. Thermogravimetric analysis (TGA) showed the suggested gel polymer electrolytes composed of only ionic liquid and polymer were stable up to approximately 400 °C. TGA and infrared spectroscopy data indicated that residual PC remains after evaporating PC in a vacuum oven, which did not affect the ionic conductivities. The GPEs containing PC displayed high conductivity (ca. 10⁻² S cm⁻¹) at 60 °C.     

Ionic conduction in P(VDF-HFP)/PVDF-(PC + DEC)-LiClO4 polymer gel electrolytes

Gel polymer electrolytes composed of poly(vinylidene fluoride-hexafluoropropylene) copolymer, poly(vinylidene fluoride) polymer, PC+DEC as plasticizer and LiClO₄ as salt have been synthesized by solvent casting technique with varying the plasticizer-salt concentration ratio systematically. Complex impedance spectroscopy has been carried out to investigate ionic conduction in P(VDF-HFP)-(PC+DEC)-LiClO₄ and PVDF-(PC+DEC)-LiClO₄ electrolyte systems. Transport number measurements have been made by Wagner’s polarization technique. With all other parameters same, P(VDF-HFP) electrolytes exhibit higher ionic conductivity and transport number as compared to PVDF based electrolytes which could be attributed to higher degree of amorphicity in the P(VDF-HFP) system. XRD and FTIR studies have been conducted to investigate the structural and complexation in the polymer gel electrolytes. Microstructural studies by SEM exhibit higher amorphicity and solvent retention capability for P(VDF-HFP)-(PC+DEC)-LiClO₄ system than those of PVDF-(PC+DEC)-LiClO₄ system.     

A novel perspective on the formation of the solid electrolyte interphase on the graphite electrode for lithium-ion batteries

In this paper, we describe how the mechanism of formation of a protective film [the solid electrolyte interphase (or interface) (SEI)] on a graphite electrode for Li-ion batteries was investigated from the novel perspective of precipitation of the final decomposition products that arise from the reduction of a nonaqueous electrolyte solution in contact with the graphite electrode. Within the framework of this new perspective, we can elegantly account for the compositional and structural differences between the basal-plane and edge-plane SEIs and for the origins of the multi-layer structure and the parabolic growth law of the SEIs on both the edge-plane and basal-plane surfaces of the graphite electrode.     

Synthesis, structure characterization and ionic conductivity of star-branched organic-inorganic hybrid electrolytes based on cyanuric chloride, diamine-capped poly(oxyalkylene) and alkoxysilane

A synthesis route for preparing highly conductive solid organic-inorganic hybrid electrolytes has been developed by using cyanuric chloride as the coupling core to react with diamino-terminated poly(oxyalkylene) triblock copolymers, followed by cross-linking with an epoxy alkoxysilane 3-glycidyloxypropyl trimethoxysilane via a sol-gel process. The present hybrid electrolyte with a [O]/[Li] ratio of 32 was found to be the most conductive, reaching a maximum lithium ion conductivity of 6.8 × 10⁻⁵ Scm⁻¹ at 30 °C. The Li-ion mobility was determined from ⁷Li static NMR line width measurements and correlated with their ionic conductivities. The onset of ⁷Li line narrowing was closely related to the T_g of the hybrid electrolytes as measured by DSC experiments. Thus, the motions of the lithium cations are strongly coupled with the segmental motion of the polymer chains, which is in line with the Vogel-Tamman-Fulcher behavior as observed in ionic conductivity.     

Enhanced thermal properties of the solid electrolyte interphase formed on graphite in an electrolyte with fluoroethylene carbonate

The influence of fluoroethylene carbonate (FEC) on the electrochemical and thermal properties of graphite anodes is examined. The dQ/dV graph of graphite/Li cells shows that the electrochemical reduction peak of an electrolyte shifts to higher potential in the presence of FEC. The DSC results for graphite anodes cycled in FEC-containing electrolytes clearly exhibit that an exothermic peak at around 120 °C mostly disappears. It is demonstrated by X-ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS) that SEI formed by the electrochemical reduction of FEC consists of a relatively high proportion of LiF and gives low interfacial resistance for graphite/Li/Li cells.     

Thermal, electrical and mechanical properties of plasticized polymer electrolytes based on PEO/P(VDF-HFP) blends

The polymer electrolytes composed of a blend of poly(ethylene oxide) (PEO) and poly(vinylidene fluoride-co-hexafluoropropylene) (P(VDF-HFP)) as a host polymer, mixture of ethylene carbonate (EC) and propylene carbonate (PC) as a plasticizer, and LiClO₄ as a salt were prepared by a solution casting technique. SEM micrographs show that P(VDF-HFP) is very compatible with PEO. The ionic conductivity of the electrolytes increases with increasing plasticizer content, while the mechanical properties become obviously worse. By addition of a certain content of PEO in P(VDF-HFP) matrix, a good compromise between high ionic conductivity and mechanical stability can be obtained.     

The effects of anion structure of lithium salts on the properties of in-situ polymerized thermoplastic polyurethane electrolytes

Thermoplastic polyurethane (TPU) electrolytes with lithium salts were prepared by an in-situ polymerization method. Three different lithium salts were used to study the effects of the anion structure on the properties of polyurethane electrolytes: LiCl, LiClO₄, LiN(SO₂CF₃)₂ (LiTFSI). The effects of the anion structure on monomer (PTMG) prior to polymerization and on the properties of TPU electrolytes post polymerization were investigated. The anion structure of lithium salt has a significant influence on the ionic conductivity, thermal stability and tensile property of TPU electrolytes. The TPU electrolytes with LiTFSI demonstrated a high ionic conductivity up to 10⁻⁵ S/cm at 300 K. The ionic conductivity of polyurethane electrolytes with lithium salts is in the order: LiCl < LiClO₄ < LiTFSI. It was found that the lithium salts with larger anions were easily dissociated in TPU and had stronger interaction with TPU, which provided more charge carriers and gave higher ionic conductivity.     

Ionic conductivity enhancement of the plasticized PMMA/LiClO4 polymer nanocomposite electrolyte containing clay

This work has demonstrated that the addition of an optimum content of dimethyldioctadecylammonium chloride (DDAC)-modified montmorillonite clay (Dclay) enhances the ionic conductivity of the plasticized poly(methyl methacrylate)-based electrolyte by nearly 40 times higher than the plain system. Specific interactions among silicate layer, carbonyl group (CO) and lithium cation have been investigated using Fourier-transform infrared (FTIR), solid-state NMR, alternating current impedance. The FTIR characterization confirms that both of the relative fractions of ‘complexed’ CO sites and ‘free’ anions increase with the increase of the Dclay content, indicating that strong interaction exists between the CO group and the lithium salt. In addition, the solid-state NMR demonstrates that the interaction between the PMMA and the clay mineral is insignificant. The addition of clay mineral promotes the dissociation of the lithium salt and thus, the specific interaction can be enhanced between the CO and the free lithium cation. However, the balanced attractive forces among silicate layers, CO groups, lithium cations and anions is critical to result in the higher ionic conductivity.     

Conductivity relaxation in the PEO-salt polymer electrolytes

The ionic conductivity of polyethylene oxide (PEO)-based electrolytes is complicated due to the coexistence of crystalline and amorphous phase below melting point of PEO complexes. The two-phase characteristics are greatly dependent upon thermal history, exhibiting variety of spherulitic morphology and crystallinity. Further complicacy comes from slow crystallization kinetics of the spherulites. We found that the ionic conductivity of PEO_nLiClO₄ polymer electrolytes under isothermal conditions, after quenching from high-temperature phase, drops significantly for roughly first 10 h and then decreases very slowly thereafter. The conductivity relaxation observed can be assigned to be a consequence of the slow recrystallization kinetics of PEO. It corresponds to a gradual, slow secondary crystallization of PEO and PEO-salt complexes corresponding to thickening of spherulitic aggregates, possibly through a development of subsidiary lamellae which fill in the space between the dominant lamellae crystals. Hence, large inconsistencies in the conductivity values reported in many papers, varying more than three orders of magnitude, are rather obvious, originated from non-equilibrium nature and slow recrystallization kinetics of semicrystalline state.     

Effect of solvent on thermal transitions and conductivity of poly (vinylidene fluoride) gel electrolytes

ABSTRACT

The melting (T_m) and crystallization (T_c) temperature increased with increasing solvent phenyl propanol (PhP) concentration in the mixture of solvent propylene carbonate and phenyl propanol (PC/PhP). It is also a little enhances of Tm and Tc with adding ethylene carbonate (EC) to propylene carbonate (PC). The melting (T_m) and softening temperature (T_soft) follows the following order of solvents PC<EC:PC<PhP:PC. There was a small change of modulus was observed with the addition of PhP. The conductivity falls with increasing PhP concentration and viscosity and re-calculate free ion concentration. The adding EC to PC raises temperatures slightly, but conductivity much the same. The overall, adding poorer solvent PhP increases the melting and crystallization temperatures at the expense of conductivity, but a little changes was observed in storage modulus, much better gel network, thereby securing the continuity of the complex leads to more flexible ductile and crystalline phase serves better mechanical properties. The crystallinity of PVDF gel electrolyte is about 50%, which facilitate to changes gel network structure slightly with PhP concentration. The formation of fully interconnected three dimensional frame work structure uniformly distributed pores with large surface area can function as efficient channels for ion conduction.     

Effect of modified montmorillonites on the ionic conductivity of (PEO)16LiClO4 electrolytes

Three kinds of modified montmorillonites were prepared by ion exchange method, and added into (PEO)₁₆LiClO₄ matrix to study the effect on the ionic conductivity of (PEO)₁₆LiClO₄ electrolytes. The structure of the modified montmorillonites and polymer composites were characterized by wide-angle X-ray diffraction. HP 4192A was used to measure the ionic conductivity of the polymer electrolytes. The results show that the addition of optimum content of 250-Li-mont enhances the ionic conductivity of the PEO based electrolyte by nearly 30 times more than the plain system and that is much higher than the other two modified montmorillonites. The difference of enhancement in conductivity caused by adding these three montmorillonites can be attributed to the difference in structure of the samples as characterized by wide-angle X-ray diffraction.