Electrodeposition of Ag and Pd on a reconstructed Au(1 1 1) electrode surface studied by in situ scanning tunneling microscopy

Electrochemical deposition of Ag and potential-induced structural change of the deposited Ag layer on a reconstructed surface of Au(1 1 1) electrode were followed by in situ scanning tunneling microscope (STM). A uniform Ag monolayer was formed on a reconstructed Au(1 1 1) surface in a 50-mM H₂SO₄ solution at +0.3 V (vs. Ag/AgCl) after adding a solution containing Ag₂SO₄ so that the concentration of Ag⁺ in the STM cell became ca. 2 μM. No characteristic height corrugation such as the Au reconstruction was observed on the surface, indicating that the lifting of the substrate Au reconstruction occurred by Ag deposition. The formed Ag monolayer was converted to a net-like shaped Ag nano-pattern of biatomic height when the potential was stepped from +0.3 to −0.2 V in the solution containing 2 μM Ag⁺. This result indicates that the substrate Au(1 1 1)-(1 × 1) surface was converted to the reconstructed surface even in the presence of Ag adlayer. Quite different structure was observed for Pd deposition on a reconstructed surface of Au(1 1 1) electrode at +0.3 V and the origin for this difference between Ag and Pd deposition is discussed.     

Resonance surface X-ray scattering technique to determine the structure of electrodeposited Pt ultrathin layers on Au(1 1 1) surface

It is demonstrated that resonance surface X-ray scattering (RSXS), in which incident X-ray energy close to the Pt L_III absorption edge (11.55 keV) is used, is very useful for the determination of the structure of electrodeposited Pt thin layers on a Au(1 1 1) surface. This technique was applied to characterize the structure of electrodeposited Pt layers on Au(1 1 1) substrates prepared under two extreme conditions, which are known to provide rough and atomically flat layers. Detailed structural information was obtained by RSXS measurements and it was confirmed that the structures of the Pt layers were as reported. Pt atoms of the atomically flat monolayer were found to be situated at the threefold hollow cubic closest packing (ccp) sites of the Au(1 1 1)-(1 × 1) surface.     

In situ FTIRS and EQCM studies of glycine adsorption and oxidation on Au(1 1 1) electrode in alkaline solutions

Dissociative adsorption and oxidation of glycine on Au(1 1 1) single crystal electrodes in alkaline solutions were studied in the present paper using cyclic voltammetry (CV), in situ FTIR spectroscopy (FTIRS) and electrochemical quartz crystal microbalance (EQCM). In situ FTIRS results demonstrated that adsorbates derived from glycine dissociative adsorption are adsorbed cyanide anions (CN_ad⁻). The CN_ad⁻ species are stable on Au(1 1 1) surface in the potential region from −0.8 to 0.0 V, and can be oxidized when electrode potential is increased above 0.1 V. The oxidation of CN_ad⁻ releases surface active sites for further glycine oxidation. The products of CN_ad⁻ oxidation were determined by in situ FTIRS as cyanate (OCN⁻), aurous cyanide (AuCN) and aurous di-cyanide (Au(CN)₂⁻). The formation of Au(CN)₂⁻ may initiate a dissolution of Au(1 1 1) surface atoms, which has been confirmed by a loss of surface mass determined in EQCM studies. It has revealed also that at high electrode potential region glycine may be split on Au(1 1 1) surface to form AuCH₂NH₂ and AuCOO⁻ adsorbates. Further oxidation of these species yielded CO₂ and -NH₂, and the AuCH₂NH₂ may be also combined with surface Au oxide to form methylamine. The CO₂ species produced in glycine oxidation are all retained in alkaline solutions to generate carbonate (CO₃²⁻) and bicarbonate (HCO₃⁻) species that were clearly determined by in situ FTIRS studies.     

In situ STM study of homoepitaxial electrodeposition on Au(1 0 0)

We have studied by in situ scanning tunneling microscopy the homoepitaxial electrodeposition on reconstructed and partially reconstructed Au(1 0 0) surfaces from chloride-containing solutions. Layer-by-layer, but strongly anisotropic, growth is observed on a completely reconstructed surface. On a partially reconstructed surface nucleation occurs on the unreconstructed areas, but the new islands formed tend to be pinned, growing anisotropically along the borders between reconstructed and unreconstructed areas.     

Adenine adsorption on Au(1 1 1) and Au(1 0 0) electrodes: Characterisation, surface reconstruction effects and thermodynamic study

Adsorption of adenine on Au(1 1 1) and Au(1 0 0) electrodes is studied by cyclic voltammetry, impedance and chronoamperometric measurements in 0.1 M and 0.01 M KClO₄ and in 0.5 M NaF solutions. The experiments performed with flame-annealed electrodes at different contact potentials, scan potential limits and scan rates, suggest different adsorption behaviour on the unreconstructed and reconstructed surface domains. This is confirmed by comparing the results obtained with electrochemically annealed unreconstructed and with flame-annealed reconstructed surfaces. In both cases the initial electrode surface state is characterised by the E_pzc values. The adsorption on reconstructed surfaces takes place at more positive potentials than on the unreconstructed surfaces and induces the lifting of the reconstruction.The thermodynamic analysis is performed on the chronoamperometric data for adenine desorption on well characterised unreconstructed Au(1 1 1) surfaces. To this end a new methodology of the chronoamperometric experiments is introduced. Quantitative thermodynamic adsorption parameters such as surface tension, Gibbs surface excess, Gibbs energy of adsorption, potential versus Gibbs excess slope and electrosorption valency are determined. Weak chemisorption of adenine is inferred with a molecular orientation independent on the coverage and on the electrode potential. It is proposed that adsorbed adenine molecules adopt a tilted orientation at the surface to facilitate the coordination to the gold atoms.     

In situ STM study of underpotential deposition of bismuth on Au(1 1 0) in perchloric acid solution

The underpotential deposition (UPD) of Bi on Au(1 1 0) was investigated in HClO₄ solution using in situ scanning tunneling microscopy. The UPD of Bi occurred in three steps. A structure, in which Bi atoms formed dimers, was found for the first UPD adlayer. A (1 × 1) image was obtained by STM at the second UPD peak. For the third UPD peak, Bi atoms formed an incommensurate adlayer, and stripes of Bi were observed on terraces. After the third UPD, a structural reconstruction caused by adsorbed Bi was observed.     

Crystalline alloys produced by mercury electrodeposition on Pt(1 1 1) electrode at room temperature

In situ scanning tunneling microscopy (STM) and reflection high energy electron diffraction (RHEED) were used to characterize mercury film electrodeposited onto a Pt(1 1 1) electrode at room temperature. Depending on the amount of Hg deposit, two different growth modes were observed. At low Hg coverage, crystalline (0 0 0 1)Hg adlayer accompanied by 30°-rotated (1 1 1)-Pt patches was found on Pt(1 1 1). Deposition of multilayer Hg resulted in layered PtHg₂ and PtHg₄ amalgams, which grew epitaxially by aligning their (2 0 1) and planes, respectively, parallel to the Pt(1 1 1) substrate. The preference of these epitaxial relationships for the electrochemically formed Pt-Hg intermetallic compounds on Pt(1 1 1) could result from minimization of the surface energy.     

Inhibition of potential-induced surface reconstruction on Au(1 0 0) electrode by the products of tyramine electro-oxidation

Our studies are focused on the stability of the unreconstructed Au(1 0 0) surface against potential-induced reconstruction in a solution containing products of tyramine (T) electro-oxidation. It is demonstrated by cyclic voltammetry and capacity measurements that in the presence of T, which reduces the stability of the reconstructed Au(1 0 0) surface, the potential-induced surface reconstruction is a fast process on condition that a preceding positive going scan is performed to potentials from the double layer region. Further extension of this scans to the potential region where the oxidation of T takes place, causes a considerable slow down of the potential-induced reconstruction. Kinetics of the potential-induced reconstruction in a solution containing products of T electro-oxidation is investigated. Inhibition of this process is explained by a strong adsorption of species produced during T oxidation on the gold surface.     

Influence of the substrate's surface structure on the mechanism and kinetics of the electrochemical UPD formation of a copper monolayer on gold

The copper electrodeposition process was studied onto different gold substrates, single crystal (1 1 1) and polycrystalline, using electrochemical techniques. It was found, from the analysis of the experimental current density transients, that the potentiostatic formation of a full copper monolayer onto the gold electrode under UPD conditions follows the same mechanism, regardless of the crystallinity of the substrate. The mechanism involved the simultaneous presence of an adsorption process and of two 2D nucleation processes, progressive and instantaneous, respectively.     

Electrosorbed carbon monoxide monolayers on Pt(1 1 1)

We review structures of high-density CO monolayers on Pt(1 1 1) surfaces in CO-saturated electrolytes or in gaseous CO at near atmospheric pressure, using surface X-ray scattering (SXS) and scanning tunneling microscopy (STM). In electrolytes, we confirmed the well-known (2 × 2)-3CO and (√19 × √19)-13CO structures and were able to study the transition between them. For gas-phase studies, we were able to stabilize extremely well-ordered CO monolayers by emersion transfer from an electrochemical cell. We found that the hexagonal close-packed (2 × 2)-3CO structure is the equilibrium phase at room temperature in ∼1 atm CO gas pressure. This commensurate (C) phase transforms continuously to an incommensurate (IC) phase at elevated temperature (a second-order phase transition). We also confirm that the (√19 × √19)-13CO structure is stable at lower CO partial pressure. This C phase transforms discontinuously to an IC phase (a first-order phase transition). A tentative phase diagram and a brief review of structure details of the (2 × 2)-3CO and (√19 × √19)-13CO phases will be presented.     

Adsorption of mercaptopropionic acid onto Au(1 1 1): Part I. Adlayer formation, structure and electrochemistry

The adsorption of 3-mercaptopropionic acid (MPA) on Au(1 1 1) in 0.1 M H₂SO₄ was studied by cyclic voltammetry, capacitance measurements and in situ scanning tunneling microscopy (STM). The formation of a self-assembled monolayer under electrochemically controlled conditions was monitored for the first time with an STM. A two-step adsorption process has been found, beginning with the adsorption of MPA to form a disordered film, which lifts the () reconstruction of Au(1 1 1), followed by an ordering of the MPA adlayer into two different dense structures. Concomitantly with the second step, formation of the well-known vacancy islands is observed. This formation is explained by an adsorbate-induced compression of the gold substrate. Two distinctly different structures of the dense MPA monolayer on Au(1 1 1) were observed. One () structure with p=3.6-4.8 and a second structure consisting of two unit cells of () and () symmetry. In part II, the effect of the MPA on the copper electrodeposition onto Au(1 1 1) is discussed.     

Potential dependent adsorption behaviour of thiothymine derivatives on the Au(1 1 1) electrode

The adsorption behaviour of 2-thiothymine and 4-thiothymine on a Au(1 1 1) single crystal electrode has been studied using cyclic voltammetry and X-ray photo electron spectroscopy. For both thio derivatives the adsorption region is restricted due to the onset of reversible oxidization to 2,2′-bis(1H-5-methylpyrimidin-4-one-2-yl)-disulphide or 4,4′-bis(1H-5-methylpyrimidin-2-one-4-yl)-disulphide at anodic potentials. Two different orientations of adsorbed 2-thiothymine have been observed. Between −350 mV and −700 mV versus Ag/Ag⁺ the molecule is solely chemisorbed via its sulphur atom and adopts an upright orientation towards the surface. However at more negative potentials 2-thiothymine is reoriented into a slightly tilted position interacting via its S, N and O atoms with the surface. In contrast, 4-thiothymine exhibits only one adsorption geometry. Between −300 mV and −700 mV versus Ag/Ag⁺ it is chemisorbed via sulphur and nitrogen adopting a slightly tilted position. At −950 mV versus Ag/Ag⁺ 4-thiothymine is irreversibly reduced. The sulphur substituent is eliminated and covers the substrate.     

Specific surface reactions for identification of platinum surface domains: Surface characterization and electrocatalytic tests

The electrochemical properties of bismuth and germanium irreversibly adsorbed on platinum electrodes have been used to screen the surface domains of polycrystalline electrodes. As revealed by the use of stepped surfaces, bismuth adsorbed on (1 1 1) terrace sites shows a redox peak at 0.63 V, whose charge is proportional to the number of (1 1 1) terrace sites, without any interference from bismuth adsorbed on any other site. For the characterization of (1 0 0) terrace sites, adsorption of germanium can be used, since the adatoms adsorbed on the (1 0 0) terrace sites show a redox peak at 0.55 V. Although no other peak is found in this potential region for the germanium adsorbed on other sites, other contributions may give rise to an increase in the current in this region. After the appropriate corrections, the charge for bismuth and germanium redox process in the selected region is proportional to the number of terrace sites with (1 1 1) and (1 0 0) symmetry, respectively. These relationships can be used to characterize the bidimensional domains of any platinum electrode. Four different platinum nanoparticle electrodes were characterized and the results were used to understand their behaviour towards ammonia oxidation.     

Carbon monoxide oxidation on Au(1 1 1) surface decorated by spontaneously deposited Pt

Platinum is deposited spontaneously on Au(1 1 1) surface from 1 mM H₂PtCl₆ + 1 M HClO₄ solution using multiple deposition procedure. X-ray photoelectron spectroscopy (XPS) analysis has shown that after immersion into the Pt containing solution and rinsing with water, Pt(OH)₂ resides on the Au(1 1 1) substrate. Consecutive depositions as well as in situ scanning tunneling microscopy (STM) and electrochemical measurements are performed on previously electrochemically reduced Pt/Au(1 1 1) surfaces. Only homogeneous distribution of thus deposited Pt islands is observed by in situ STM. With subsequent depositions, the width of deposited Pt islands increases, but stays lower than 10 nm, while a significant increase of Pt islands height is observed, leading to moderate increase of the coverage. Cyclic voltammetry (CV) profiles of obtained Pt/Au(1 1 1) surfaces, and CO stripping curves are recorded in 0.5 M H₂SO₄ solution. CO oxidation takes place only at higher potentials shifting negatively with increasing coverage. This is discussed with respect to Pt islands width and height distributions and to the influence of the Au(1 1 1) substrate surface.     

A novel spectroelectrochemical cell for in situ surface X-ray scattering measurements of single crystal disk electrodes

A newly designed spectroelectrochemical cell was constructed for surface X-ray scattering (SXS) to study single crystal electrodes. Electrochemical characteristics of a specific face of a single crystal electrode can be investigated in the meniscus mode, and SXS measurement can be easily carried out using the spectroelectrochemical cell. The usefulness of the present cell was demonstrated by studying the electrochemical deposition of thin Pd layers on Au(111) and Au(100) that require precise amounts of Pd deposits.     

Redox behavior of hemin at p-GaAs(1 0 0) electrode

Electrochemical behavior of hemin on p-GaAs(1 0 0) electrodes was examined by cyclic voltammetry (CV) and impedance spectroscopy (EIS) in phosphate buffer solutions (PBS) at pH 7.45. CV investigations in 0.6 mM hemin in PBS revealed a pair of reversible peaks at −0.44 and −0.32 V vs. SCE resulting in stable adsorbed species. EIS spectra analysis pointed out that these adsorbed species bring significant changes in the semiconductor surface state population and the potential drop distribution between the semiconductor space charge region and the Helmholtz layer.     

In situ radiotracer and voltammetric study of the formation of surface adlayers in the course of Cr(VI) reduction on polycrystalline and (1 1 1) oriented platinum

This paper is focused on the in situ radiotracer and voltammetric studies of the induced HSO₄⁻/SO₄²⁻ adsorption at Pt(poly) and Pt(1 1 1) surfaces in 0.1 mol dm⁻³ HClO₄ solution in the course of Cr(VI) electroreduction. Besides this, the sorption behavior of HSO₄⁻/SO₄²⁻ ions on bare Pt(poly) and Pt(1 1 1) electrodes is compared and discussed. From the experimental results it can be stated that: (i) although the extent of bisulfate/sulfate adsorption is strongly dependent upon the crystallographic orientation of Pt surfaces, the maximum coverage on the Pt(1 1 1) does not exceed 0.2 monolayer; (ii) the Cr(VI) electroreduction on both poly- and (1 1 1) oriented platinum proceeds via a ce (chemical-electron-transfer) mechanism to yield Pt surfaces covered with intermediate surface adlayers containing Cr(VI) particles (and reduced Cr-containing adspecies) and ‘strongly bonded’ HSO₄⁻/SO₄²⁻ ions; (iii) while the coverage of platinum surfaces by the intermediate complexes formed in the course of Cr(VI) electroreduction at E > 0.20 V is basically independent of the crystallographic orientation of the Pt electrode, the onset for rapid Cr(VI) reduction is highly affected by the nature and crystallographic orientation of the electrode.     

Influence of chemical additives on the surface reactivity of Si in KOH solution

It is known that the electrochemistry of silicon in alkaline solution is closely linked to the anisotropic etching of the semiconductor. In this work the influence of two commonly used additives, hydrogen peroxide and isopropyl alcohol, on the surface chemistry of silicon in KOH solution was investigated by electrochemical methods. The results allow us to draw conclusions regarding the role of the additives in the chemical and electrochemical reactions.     

Adsorption of 2-X-benzoic acids (X = fluoro, chloro, and bromo) on Au(1 0 0) electrode in acidic media studied by IRAS

Adsorption behaviors of 2-fluoro-, 2-chloro-, and 2-bromobenzoic acids on Au(1 0 0) electrode in 0.1 M HClO₄ have been investigated by using in situ reflection adsorption IR spectroscopy and differential capacity measurements. It is found for the 2-substitued benzoic acids that the flat lying adsorbed species is present at negative potentials, and the vertically adsorbed benzoate with both oxygen atoms oriented toward the metal surface is present at positive potentials. A new adsorbed state due to the vertical orientation was observed around 0.75 V only in 2-fluorobenzoic acid solution, as well as the case of benzoic acid. This indicates that the new band is due to the formation of an ordered adsorption layer of the vertical 2-fluorobenzoate, and the formation of the arrangement adsorption is dependent on the size of the adsorbed molecule.