Dentastic bond strength to dentin

PURPOSE: To evaluate the shear bond strength to the dentin of permanent teeth and failure site of Dentastic hydrophilic dentin bonding agent. MATERIALS AND METHODS: Forty permanent noncarious molar teeth stored in distilled water were obtained. The teeth were cleaned with pumice and a rubber cup. The mesio-buccal surface of the teeth was ground flat with hand pressure with a series of SiC paper ending with the 600 grit to provide a uniform surface on dentin to which the resin composite could be applied. After preparing the tooth surface, the teeth were stored in distilled water for 48 hours. They were then divided at random into four groups of 10 specimens each: Group 1: Dentastic, five coats of primer; Group 2: Dentastic, three coats of primer; Group 3: Dentastic, five coats of primer, light-cured adhesive before resin bonding; Group 4: Dentastic, three coats of primer, light-cured adhesive before resin bonding. All specimens were thermocycled (500x) and sheared in a testing machine. After shear testing, the debonded sites of all samples were examined with a stereomicroscope and a scanning electron microscope. RESULTS: The results in MPa were: Group 1: 22.63 +/- 6.24; Group 2: 23.35 +/- 5.14; Group 3: 23.58 +/- 5.66; Group 4: 27.26 +/- 8.22. ANOVA and Student-Newman-Keuls showed no statistically significant difference between the groups. In all groups, all specimens failed at the dentin (dentin cohesive failure = dentin fracture) or at the resin (resin cohesive failure = resin fracture). This means that the bond strength of the product is stronger than the cohesive strengths of the dentin and the resin.     

Bond strength of multi-step and simplified-step systems

PURPOSE: To measure and compare the in vitro shear bond strength (SBS) of the following three pairs of multi- and simplified-step dentin bonding systems: OptiBond vs. OptiBond FL, All-Bond 2 vs. One-Step, and Tenure vs. Tenure Quik. MATERIALS AND METHODS: 60 extracted human mandibular molars were sectioned perpendicular to the long axis 1 mm above the CEJ to expose the dentin bonding surface. After being wet-ground to 600 grit with SiC abrasive papers, rinsed and dried, the teeth were individually mounted in phenolic rings with epoxy resin, and randomly assigned into six equal groups of 10 each. The dentin surfaces were treated with the above mentioned dentin bonding systems, and a gelatin cylinder filled with resin composite (Pertac-Hybrid) was directly bonded to each pretreated surface. After 7-day storage in 37 degrees C water followed by thermocycling, the specimens were shear tested to failure on an Instron machine. Data were analyzed by independent t-tests, one-way ANOVA, and Duncan's Multiple Comparison tests at alpha = 0.05. RESULTS: Except for the pair Tenure/Tenure Quik, the differences between the pairs All-Bond 2/One-Step and OptiBond/OptiBond FL were statistically significant with All-Bond 2 and OptiBond FL yielding higher shear bond strength (P < 0.05). Findings of this study indicated that OptiBond FL was the only simplified-step system showing improved bond strength.     

Dyes for caries detection influence sound dentin bond strength

This study evaluated the influence of caries-detection dyes on the in vitro tensile bond strength of adhesive materials to sound dentin. Caries-free human molars were ground to expose superficial dentin. Two dyes (a commercial 0.5% basic fuchsin in propylene glycol and Cari-D-Tect) were applied to sound dentin and rinsed. Subsequently, the dentin was etched with phosphoric acid (35%) and rinsed, leaving a moist dentin surface. The adhesive (Prime & Bond 2.0) was applied in two layers and light cured. A composite (TPH Spectrum), a compomer (Dyract), and a hybrid ionomer (Advance) were used to prepare the bond-strength specimens with a 3-mm-in-diameter bonding area. Control groups were made without use of dyes. Six specimens were prepared for each group. After 24 hours in distilled water, tensile bond strength (MPa) was measured using a testing machine. Analysis of variance was used to evaluate the data. Without dyes, bond strengths of TPH Spectrum and Dyract with Prime and Bond 2.0 were similar and both values were significantly (P < 0.05) higher than that of Advance with Prime & Bond 2.0. Dyes for caries detection reduced the bond strength of TPH Spectrum and Dyract but not Advance when used with Prime and Bond 2.0.     

Bond strength and interfacial morphology of adhesives to primary teeth dentin

PURPOSES: To evaluate (1) the shear bond strength to the dentin of primary teeth and failure site of hydrophilic dentin bonding agents, (2) the interfacial micromorphology of these adhesives on primary teeth. MATERIALS AND METHODS: Seventy-six primary noncarious molars stored in distilled water were obtained. The teeth were cleaned with pumice and a rubber cup. The mesio-buccal surface of the teeth was ground flat with hand pressure with a series of SiC paper ending with the 600 grit to provide a uniform surface on superficial dentin to which the adhesives and resin composite could be applied. After preparing the dentin surface, the teeth were stored in distilled water for 48 hours. They were then rinsed and dried with compressed air and divided at random into four groups of 16 specimens each: Group 1: Dentastic; Group 2: One-Step; Group 3: Prime & Bond 2.0; Group 4: Compoglass SCA. Z100 resin was used in all groups. All specimens were thermocycled (500x) and sheared in an Instron machine. After shear testing, the debonding sites of all samples were examined with a stereomicroscope and selected samples were also examined with the scanning electron microscope. Three additional samples per group were used to evaluate the resin adaptation to dentin. RESULTS: The results in MPa were: Dentastic 19.62 (4.67); One-Step 11.24 (3.67), Prime & Bond 22.38 (6.47), Compoglass SCA 18.88 (4.04). ANOVA (P < 0.0001) revealed that there was a significant difference between the groups. The Student-Newman-Keuls test (P < 0.05) showed no statistically significant difference between Dentastic, Prime & Bond and Compoglass SCA. However, these three groups were statistically significantly higher than One Step. In the Dentastic group, 14 of 16 samples revealed resin cohesive failure (resin fracture) while two of 16 displayed dentin cohesive failure (dentin fracture). In the One Step group, 15 samples failed at the resin and one sample showed dentin cohesive failure. In the Prime & Bond group, 12 specimens revealed resin cohesive failure while four displayed dentin cohesive failure. In the Compoglass SCA group, 13 samples had resin cohesive failures while three had dentin cohesive failures. All samples revealed an intimate adaptation to the dentin displaying resin tag formation.     

Bond strength to crown and root dentin

PURPOSE: To investigate (1) the tensile bond strengths of four commercial dentin bonding systems to bovine crown and root dentin and (2) the structure of the hybrid layers for each system bonded to the two dentin substrates. MATERIALS AND METHODS: Superficial surfaces were exposed in bovine crown and root dentin. The teeth were embedded in plaster and a 3 mm diameter bonding area was demarcated. The four bonding systems used were All-Bond 2, Super-Bond D-Liner Plus, Clearfil Liner Bond II, and ProBond. Bonding procedures followed the manufacturers' instructions with the exception of Super-Bond D-Liner Plus where the primer was left in situ for 60 seconds. Tensile bond strengths were tested after 24-hour storage in 37 degrees C deionized water. Specimens were also prepared for SEM observation of the hybrid layer, after treatment with 10% phosphoric acid, and 10% phosphoric acid and 5% sodium hypochlorite. RESULTS: Statistically lower bond strengths to crown dentin when compared with root dentin were observed for All-Bond 2, whereas Liner Bond II showed the opposite (P < 0.01). Both ProBond and Super-Bond D-Liner Plus showed no statistical differences between crown and root dentin (P > 0.05). Hybrid layers could be observed for All-Bond 2, Liner Bond II and Super-Bond D-Liner Plus, with no apparent differences between the hybrid layers of crown and root dentin. In the case of ProBond, where the smear layer was not removed during the priming stage, it appeared that the primer had infiltrated and caused hybridization of the smear layer. The differences in bond strength were thought to be related to the different bonding mechanisms of each material, as well as possible variations in the crown and root dentin substrates.     

Quantitative contribution of the collagen network in dentin hybridization

PURPOSE: To determine the quantitative contribution of dentin hybridization to bonded assembly strength and demonstrate the micromorphology of the interface with and without collagen present. MATERIALS AND METHODS: Four groups of 10 molar teeth were finished to a 320 grit dentin smear layer. Two groups served as controls and two experimental groups were subjected to collagenase digestion of the collagen exposed by acid conditioning. All-Bond 2 and Amalgambond were used to bond Bisfil and Epic resin composite, respectively. Stored in water at 37 degrees C for 24 hours the assemblies were tested in a shear mode at a crosshead speed of 5 mm/minute. Means and standard deviations were subjected to analysis for statistical significance. Twenty four teeth in four groups were examined by scanning (SEM) and transmission electron microscopy (TEM) for the relationship between resin and conditioned dentin with and without the collagen network. RESULTS: All-Bond 2 and Amalgambond controls were 28.41 +/- 3.9 and 19.04 +/- 5.96 MPa, collagenase-treated groups scored 26.43 +/- 2.90 and 19.70 +/- 4.25 MPa respectively. No significant difference existed between the control and experimental groups. SEM showed an intertubular collagen network with patent tubules and a pronounced porous, irregular dentin topography following collagen digestion. A distinct hybrid zone and tubular penetration was observed but the collagenase-treated specimens showed only resin in the tubules and their lateral extensions. TEM confirmed the absence of a distinct hybrid zone in the collagenase groups with a tight, gap-free junction between the resin and the undemineralized dentin. An electron dense zone (< 50 nm) at the leading edge of conditioning was observed for All-Bond 2 and Amalgambond groups. It was concluded that the resin-reinforced or hybridized, collagenous network does not detract from, nor contribute any significant quantitative value per se to dentin bonding with the systems tested.     

The influence of the depth of substrate dentin surface and thickness of the current restorative samples on bond strength

The effect of sample thickness and dentin depth on bond strength of composite, compomer and resin modified glass ionomer have been investigated. The occlusal surfaces of 84 non carious human third molars were used for bonding. 4 subgroups were tested, superficial dentin with sample thickness 1 and 2 mm and deep dentin with sample thickness 1 and 2 mm respectively SBMP + /Z 100 composite showed 26 +/- 3.2, 22.3 +/- 4.5, 17 +/- 3.2 and 21.8 +/- 4.2 MPa shear bond strength to S. dentin 1 mm, deep dentin 1 and 2 mm and S. dentin 2 mm respectively. Compoglass reported 10.4 +/- 1.57, 9.1 +/- 2.3, 5.0 +/- 0.6 and 9.24 +/- 3.1 MPa while, Vitremer achieved 4.7 +/- 0.49, 3.2 +/- 0.39, 3.0 +/- 0.81 and 3.2 +/- 0.53 MPa. It is concluded that the highest bond strength can be achieved to superficial dentin in thickness or increments not more than 1 mm. And that both dentin depth and sample thickness might influence the quality of the bond to dentin with an effect that varies from one material to another depending upon the mechanism of bond of each material and its chemical composition.     

Microleakage of new dentin bonding systems using human and bovine teeth

The objective of this study was twofold: to evaluate the microleakage behavior of three dentin bonding systems and to determine if bovine teeth are comparable substrates to human teeth when studying the microleakage of various materials. The materials evaluated were Scotchbond Multi-Purpose Adhesive, Prisma Universal Bond 3, and All-Bond 2. All three bonding systems were used in combination with Prisma APH hybrid composite for comparison of microleakage behavior. Sixty class 5 preparations were cut at the cementoenamel junction for groups containing 30 human and 30 bovine teeth. A 1 mm 45 degree bevel was placed at the enamel margin. Teeth were grouped according to the dentin bonding system used and then restored according to the manufacturer's directions. After restoration, the teeth from each group were stored in distilled water at 37 degrees C for 3 days. The teeth were then thermocycled between 4 degrees C and 58 degrees C for 100 cycles and returned to distilled water at 37 degrees C for an additional 4 days. The teeth were then sealed with nail polish up to 1 mm from the margins of the restoration and placed in 45Ca isotope for 2 hours. The teeth were then sectioned and placed on x-ray film to produce autoradiographs. Microleakage was evaluated for the enamel and dentin margins separately using the following scale: 0 = no leakage, 1 = penetration of isotope to less than 1/2 the distance to the axial wall, 2 = penetration of isotope greater than 1/2 of the distance to the axial wall but short of the axial wall, and 3 = penetration of isotope to the axial wall or beyond. The materials were compared to each other using the Mann-Whitney U and Kruskal-Wallis tests. The gingival margins were compared to the incisal margins for all materials. No statistically significant differences in microleakage were revealed between the incisal and gingival location for human substrates, but there was statistically significant greater gingival microleakage for bovine substrates. All-Bond 2 leaked significantly more than Scotchbond Multi-Purpose for human substrates at the incisal margin. All-Bond 2 had significantly more microleakage than Prisma Universal Bond 3 at both dentin and enamel margins for the bovine substrate. There were no statistically significant differences in microleakage among the bonding systems for the human substrate. No statistically significant differences between the microleakage behavior of human and bovine substrates were found. These results support the use of bovine teeth for in vitro microleakage studies.     

Initial tensile bond strength of resin-modified glass ionomers and polyacid-modified resins on perfused primary dentin

The objective of this study was to evaluate the initial tensile bond strength of a resin-modified glass ionomer (Photac-Fil) and two polyacid-modified composite resins (Compoglass, Dyract) to primary dentin. A hybrid composite resin (Tetric) and two chemical cured glass ionomers (BaseLine, Hi-Dense) served as controls. Ninety caries-free dentinal discs were ground flat and perfused with Ringer's solution. Dentinal surfaces were conditioned (except for Base Line). From each material, fifteen standardized specimens were attached to the dentin. Light-curing of the respective materials followed (1 min), and adhesion was tested with a universal testing machine 15 min after application. The highest initial bond strength was observed with Tetric (5.17 MPa). Closed test procedure (Kruskal-Wallis) showed significant differences between all materials (P < 0.05), except for Compoglass (1.82 MPa) vs. Dyract (2.35 MPa), and BaseLine (0.37 MPa) vs. Photac-Fil (0.42 MPa). The condensable glass ionomer Hi-Dense revealed a mean tensile bond strength of 0.79 MPa. Adhesion of (polyacid-modified) composite resins is superior to the other tested glass ionomer materials, when applied to perfused primary dentin.     

Effects of aging on tensile fatigue strength of bovine dentin

The effects of aging on the tensile fatigue strength of bovine dentin were investigated. Tensile tests and tensile fatigue tests were performed in 37 degrees C water with bovine dentin specimens of two different age groups. The tensile strengths of the young group and the adult group were 74.0 MPa and 72.7 MPa, respectively; there was no significant difference between the young and the adult group. However, the tensile fatigue strength of the adult group, 46.9 MPa, was significantly weaker than that of the young group, 51.0 MPa. There was a obvious difference between the tensile fracture surface and the tensile fatigue fracture surface; a smooth surface of the peritubular dentin and an uneven surface of the intertubular dentin were clearly distinct in the fatigue fracture surface. Plugged dentinal tubules and narrower dentin tubules were commonly observed in the adult group. These morphological changes were suggested to be the reason for the decrease in the tensile fatigue strength with aging.     

The effect of dentin primer on the tensile bond strength to human enamel

Four third-generation dentin bonding products (Scotchbond Multi-Purpose, Optibond, All-Bond 2, and Prisma Universal Bond 3) were tested to evaluate their tensile bond strength to enamel. Test enamel specimens were etched, primed, and polymerized according to each manufacturer's directions. Control specimens were treated identically except the primer application was eliminated. The results demonstrated that the dentin primer significantly increased the tensile bond strength of All-Bond 2, significantly decreased the tensile bond strength of Scotchbond Multi-Purpose and Optibond, and had no significant effect for Prisma Universal Bond 3. A one-way analysis of variance was run between the eight groups tested, and three significant subsets were found (P < .05). The subset with the highest mean tensile bond strengths consisted of Prisma Universal Bond 3 primed and nonprimed, All-Bond 2 primed, and Optibond nonprimed.     

The effect of dentin disinfectants on shear bond strength of resin-modified glass-ionomer materials

The purpose of this study was to investigate the effect of dentinal disinfection with a 2% chlorhexidine or a 0.11% I2-KI/CuSO4 solution on the shear bond strength of three resin-modified glass-ionomer cements: Fuji II LC, Photac-Fil, and Vitremer. The occlusal surfaces of extracted human teeth were flattened to dentin. Specimens were randomly assigned to one of nine treatment groups (n = 12). For each glass-ionomer material, there was a control group and two treatment groups in which the dentin was treated with either a 2% chlorhexidine or a 0.11% I2-KI/CuSO4 solution before the dentin was treated with the recommended dentin conditioner prior to glass-ionomer bonding. Specimens were stored for 1 day in water, thermocycled, and tested in shear until failure. The chlorhexidine solution did not significantly affect the shear bond strengths of any of the cements, but the I2-KI/CuSO4 solution significantly lowered the bond strengths of Vitremer and Fuji II LC compared to the controls.     

Effects of aminobenzoic acid derivatives with 4-AET/HEMA in self-etching primer on bonding to ground dentin

The effect of the inclusion of aminobenzoic acid derivatives (ABAD) in a self-etching primer comprising 4-acryloxyethyltrimellitic acid (4-AET), HEMA and water on shear bond strength to ground dentin was investigated. The mean bond strengths to dentin were significantly increased by the inclusion of 0.307 mol% ABAD in the 4-AET/HEMA primer, when compared with the control (0 wt% ABAD) (p < 0.01). A particularly high value (38.0 MPa) of shear bond strength was obtained in the use of the primer containing p-nitroanthranilic acid (p-NAA). It seemed to assume that the effect of p-NAA could be caused by the strong electron-withdrawing group of -NO2. From SEM observation, it was found that bonding resin appeared to adhere strongly to the ground dentin without formation of any resin-tags in the dentinal tubules. It was thought that the ABAD with 4-AET/HEMA could perform facilitating photo-polymerization at the bonding interface, and resulted in increased bond strength to ground dentin, and that the bond strength could be affected by the electronegativities of substitutional groups of ABAD.     

-Apatite rheumatism, unusual aspects-

OBJECTIVES: The goal of this study was to evaluate the effects of cryopreservation of teeth on dentin bond strength as a function of remaining dentin thickness. METHODS: Flat occlusal surfaces of human dentin were prepared in 54 freshly extracted teeth and 54 thawed, cryopreserved teeth. In each group, 18 bonds were performed in superficial dentin, 18 in mid-coronal, and 18 in deep dentin. A resin composite cylinder, 3 mm in diameter and in height, was bonded orthogonally to the surface. After storage in distilled water at room temperature for 1 wk, the bonded cylinders underwent shear testing at a crosshead speed of 0.5 mm min-1. The mean remaining dentin thickness was calculated after longitudinally sectioning the debonded samples through the center of the bonded area. Non-parametric statistical analyses were used to correlate the shear bond strength with the remaining dentin thickness among the storage modes and within the different dentin regions. RESULTS: The lowest shear bond strength values were found in the deep dentin of both fresh and cryopreserved dentin, while the values in deep and mid-coronal dentin were not significantly different in fresh and cryopreserved dentin. In the superficial and mid-coronal dentin of cryopreserved samples, the shear bond strength values were identical. There was a significant difference between the shear bond strength values in the superficial dentin of fresh teeth compared to the values for cryopreserved teeth. SIGNIFICANCE: According to the experimental conditions, tooth cryopreservation shows some promise as a substitute for freshly extracted teeth, provided that the experiments are performed in midcoronal and deep dentin.     

The effect of air abrasion on shear bond strength to dentin with dental adhesives

This study compared the effects of different dentin surface treatments on the shear bond strengths of three adhesive systems. The adhesive systems included a resin-modified glass ionomer, Fuji II LC, and two dentin bonding systems, One Step and Scotchbond Multi-Purpose Plus. The surface treatments compared for each adhesive system were as follows: 1) the controls, which were conditioned, 2) air abrasion at 120 psi without conditioning, 3) air abrasion at 160 psi without conditioning, 4) air abrasion at 120 psi with conditioning, and 5) air abrasion at 160 psi with conditioning. The KCP 1000 Whisperjet was used for all air-abrasive specimens. Controls for each adhesive material (Fuji II LC, One Step, Scotchbond Multi-Purpose Plus) were bonded using manufacturers' recommendations. Results showed that air abrasion significantly lowered bond strength of the resin-modified glass ionomer, conditioned or nonconditioned (P < 0.01). Air abrasion alone significantly lowered bond strengths of the dentin bonding agent systems (P < 0.01). However, air abrasion plus conditioning of the dentin surface resulted in bond strengths that were similar to the conditioned-only specimens (P < 0.01).     

Effect of 4-acryloxyethyltrimellitic acid in a self-etching primer on bonding to ground dentin

To develop a self-etching primer for ground dentin, 4-acryloxyethyltrimellitic acid (4-AET) was newly synthesized, and the effect of concentrations varying from 0 (control) to 56.5 wt% 4-AET in the water/ HEMA primer on bonding to the dentin was investigated. Bond strength to the dentin was significantly affected by the inclusion of 4-AET in the primer which also contained N,N-di(hydroxyethyl)-p-toluidine (DEPT) when compared with the control (0% 4-AET) (p < 0.01). The optimum 4-AET-concentration and the mean bond strength (SD) were found to be 6.5 wt%: 24.2 (3.6 MPa, 37.4 wt%: 25.3 (4.4) MPa, 47.2 wt%: 26.9 (11.6) MPa and 54.4 wt%: 29.7 (12.9) MPa. The role of DEPT in the 4-AET/HEMA primer was assessed, and the optimum DEPT-concentration was found to be 0.154 and 0.307 mol%. Regarding the hypothetical bonding mechanism to dentin, it was thought that the ionized 4-AET in water/HEMA would penetrate into dentin substrates, and DEPT as an accelerator in situ would facilitate photo-polymerization at the dentin-resin interface, and result in increased bond strength to ground dentin.     

Effects of etchants, surface moisture, and resin composite on dentin bond strengths

This in vitro study evaluated the effects of etchant type, surface moisture, and resin composite type on the shear bond strength of dentin adhesives. Three adhesives which bond to etched dentin were used in the study: All-Bond 2, Amalgambond, and Clearfil Photo Bond. Occlusal enamel was removed from 200 human molars to expose dentin. The dentin surfaces were etched, treated with a dentin adhesive system, and bonded with resin composite. After thermocycling and storage, the composite columns were fractured from dentin using an Instron machine. Bond strengths were calculated and subjected to a statistical analysis. Etchant type, surface moisture, and resin composite type all had significant effects on dentin bond strengths. Overall, the highest bond strengths were obtained with 10/3 etchant, moist dentin, and hybrid composite. The highest bond strengths for All-Bond 2 and Amalgambond were obtained by using the manufacturer's recommended etchant, moist dentin, and a hybrid composite. The mean bond strengths for All-Bond and Amalgambond under these conditions were 22.5 and 19.0 MPa, respectively. Clearfil Photo Bond had significantly lower bond strengths, but was relatively unaffected by changes in experimental conditions.     

Cysteine and glutathione deficiency in AIDS patients: a rationale for the treatment with N-acetyl-cysteine

The purpose of this study was to determine the effect of accidental dentin primer contact with etched enamel on shear bond strength of composite resin to enamel. Four dentin bonding systems were included in this study: GLUMA Dentin Bond, Scotchbond, and Prisma Universal Bond 2 and 3. Eighty extracted human permanent anterior teeth were used and divided in eight test groups. The vestibular surfaces were ground and acid etched. For each dentin bonding system 10 samples were treated with dentin primer prior to placement of resin. Shear bond testing showed that enamel contact with dentin primer in the above two systems decreased the shear bond strength between composite and enamel by 31 to 44%.     

Effect of application technique and dentin bonding agent interaction on shear bond strength

This study evaluated the interaction of five clinical application techniques and the shear bond strength of four DBAs (OptiBond FL, Clearfil SE Bond, PQ1 and Prime & Bond NT). A hybrid resin composite (Herculite XRV restorative resin) was attached to human dentin surfaces using five application techniques: Group A--adhesive spread with a 3M brush for 30 seconds, followed by compressed air 0.5 cm from the surface for one second to remove the excess adhesive. Group B--adhesive spread with a 3M brush for 30 seconds, followed by compressed air 0.5 cm from the surface for three seconds to remove the excess adhesive. Group C--adhesive spread with 3M brush for 30 seconds, excess adhesive removed with a clean brush, two strokes side by side, no compressed air. Group D--adhesive spread with a Micro-applicator brush for 30 seconds followed by compressed air 0.5 cm from the surface for one second to remove the excess adhesive. Group E--adhesive spread with a Micro-applicator brush for 30 seconds, the excess adhesive removed with a clean brush, two strokes side by side and no compressed air. The specimens were stored in distilled water at 37 degrees C for 24 hours, followed by thermocycling between 5 degrees C and 55 degrees C for 1,000 cycles. The shear bond strengths were determined on a universal testing machine operating with a crosshead speed of 5 mm/minute. The fracture sites were examined by 20x stereo microscope to determine the type of failure that occurred during the debonding procedure. Bond strength data were compared with analysis of variance at a significance level of p<0.05. Post hoc comparisons of means were performed with t-tests with p-values adjusted for multiple comparisons. This in vitro study concluded that there was an interaction between the application technique and bonding agent tested. All DBAs utilized the one-second compressed air technique, which yielded the highest bond strengths.