首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 171 毫秒
1.
为了提高筋条减阻表面的加工质量,对磨粒有序化砂轮的磨削力对工件表面几何形状的影响规律进行研究。首先,根据筋条减阻表面的参数,设计能够实现筋条减阻表面加工的错位排布砂轮;其次,建立了筋条减阻表面磨削过程的简化模型,并基于有限元对工件表面形貌进行了力学仿真;最后,研究磨削速度、磨削深度、磨粒角度、排布参数等对筋条表面几何形状的影响规律,综合探讨磨削力和表面形貌之间的关系。结果表明,在磨削速度增大时,工件表面材料的隆起变形高度随着磨削力的减小而增大;在磨削深度增大时,材料的隆起变形高度随着磨削力的增大而增大;在磨粒角度增大时,材料隆起变形高度随着磨削力的增大,先增大后减小;在磨粒排布参数增大的过程中,材料隆起变形高度随着磨削力的增大而增大。  相似文献   

2.
张银霞  韩程宇  杨鑫  王栋  刘治华 《表面技术》2019,48(10):342-348
目的 对不同磨削工艺参数下的平面磨削力进行预测,对磨削机理进行研究,进而控制磨削加工质量。方法 考虑CBN砂轮表面磨粒形状的多样性、姿态的多样性和空间分布的随机性,建立CBN砂轮模型,对GCr15材料模型进行有限元砂轮磨削仿真。同时使用CBN砂轮,采用不同的工件进给速度对GCr15进行单因素平面磨削实验,使用三坐标测力仪测量不同磨削参数下的磨削力。结果 建立的仿真砂轮模型的表面形貌与真实砂轮接近,仿真砂轮上的磨粒出刃高度均服从正态分布,与实际砂轮一致。对比随机多面体磨粒模型和真实CBN磨粒照片,两者形貌相似。磨削力实验和仿真结果表明,工件进给速度由3 m/min增大到18 m/min时,磨削力逐渐增大,仿真所得法向磨削力最大误差远小于切向磨削力。结论 实验结果与仿真结果具有一致性,证明了砂轮磨削有限元仿真模型可用于磨削力预测。因为仿真中无法考虑实际砂轮尺寸和砂轮表面结合剂对磨削的影响,结果具有一定误差,仿真的准确性有待进一步提高。研究结果为使用有限元方法研究磨削机理和控制磨削加工质量提供了思路。  相似文献   

3.
为研究TC4合金在介观尺度下的磨削过程中切屑变形区的应力分布对切屑的形成及磨削工件表面质量的影响,基于热-力耦合理论建立了单颗磨粒磨削理论模型,并利用ABAQUS对磨削过程进行了有限元仿真分析。仿真结果表明:当磨削深度小于0.5μm时,继续减小有利于减小切屑变形区流动应力的变化幅度,从而提高工件质量;与磨粒圆锥角度相比,磨削速度对切屑变形区应力变化影响更为显著,其变化值基本保持在400MPa左右。研究结果对进一步提高工件表面质量及TC4合金的磨削性能奠定了理论基础。  相似文献   

4.
李厦  王锴霖 《表面技术》2018,47(7):265-269
目的通过对比研究磨削过程中超声振动辅助缓进给磨削工件表面的温度变化,验证超声振动对磨削热的影响,为进一步研究磨削机理提供依据。方法基于磨削温度场解析模型,建立了磨削热源平均强度。运用ANSYS软件热分析模块分别对普通缓进给磨削和超声辅助缓进给磨削进行了工件表面温度场仿真,得到了不同载荷步的温度场分布以及工件表面的温度时间变化曲线,较准确地反映了磨削工件时工件表面的温度变化。结果试验和模拟表明,缓进给磨削工件时,工件表面温度较高,对工件施加超声振动后,能够有效降低磨削力,减少磨削过程中产生的热量,降低工件表面温度20%左右。结论超声振动辅助磨削工件时,由于工件高频振动导致磨粒与工件间断性接触,使磨削过程变为有规律的脉冲状断续磨削,有利于工件散热,降低了磨削温度,为避免缓进给磨削时容易出现的磨削烧伤现象提供了技术支持。  相似文献   

5.
磨削与抛光是实现单晶硅材料超精密表面加工的重要工艺方法,磨抛协同加工过程中由磨粒运动状态主导的二体与三体磨损机制对材料去除效率以及表面加工质量具有重要影响。采用分子动力学方法,建立固结与游离运动状态双磨粒协同作用下的单晶硅表面超精密磨抛加工过程仿真模型,分析磨粒切入深度、横向与纵向间距干涉等因素对磨削力、材料相变、表面损伤及材料去除行为的影响规律,阐释单晶硅磨抛协同超精密加工表面形貌演化规律。研究表明:受磨粒运动状态驱动的单晶硅材料表层损伤原子数量随固结及游离磨粒切入深度增大而增加,磨粒切入深度对工件的材料去除、裂纹生长及损伤行为影响显著;法向和切向磨削力随磨粒切入深度增加而增大,且在同等切入深度变化时法向磨削力增加幅度大于切向磨削力; 通过单晶硅金刚石结构分析磨粒间干涉区域的损伤情况可知,随着磨粒间纵向间距增加时,工件所受干涉作用减小,六角金刚石晶体结构减少;相比较固结磨粒,游离磨粒对工件的损伤区域更深,产生瞬态缺陷原子更多。研究结果可为实现超精密磨抛协同加工工艺高材料去除效率和高表面质量提供理论基础。  相似文献   

6.
在微粉金刚石磨具的制备过程中,金刚石热损伤和磨粒与结合剂间界面特性是影响磨具性能的主要因素。利用电铸与钎焊相结合的工艺把表面镀钛和未镀钛两种微粉金刚石磨料制备成磨具,并将其用于氧化铝陶瓷的磨削试验。通过对钎焊后金刚石磨粒与钎料的界面分析,磨削力、磨粒脱落率以及工件表面粗糙度的比较,探讨磨粒表面镀钛对钎焊微粉金刚石磨具性能的影响。结果表明,镀钛微粉金刚石表面镀层在钎焊过程中对微粉金刚石起到包裹隔离的作用,可以降低微粉金刚石的热损伤和石墨化;在利用两种钎焊微粉金刚石磨具磨削氧化铝陶瓷时,镀钛微粉金刚石磨具的磨削力较小,磨料的脱落率也较少,且工件表面粗糙度值更低。综合比较,磨粒表面镀钛后,可以减弱微粉金刚石的热损伤,提高磨具的磨削性能。  相似文献   

7.
工件旋转磨削广泛用于加工单晶硅、玻璃、陶瓷等硬脆材料,预测其磨削表面纹理特征对研究磨削机理、优化磨削工艺有重要意义。基于对现有工件旋转磨削仿真模型的分析与实验验证,讨论其存在的问题及改进方向:在超细砂轮模型中应修正有效磨粒数;基于现有单磨粒划擦实验的基本结论和超精密磨削的特点,工件材料回弹、磨粒刃尖半径以及磨粒成屑临界切深是需进一步考虑的因素。研究结果有助于提升对磨削机理和工艺的认识,进而提高工件旋转磨削效率。   相似文献   

8.
用小直径砂轮超声振动磨削和普通磨削加工SiC陶瓷零件,对比研究砂轮线速度、工件进给速度、磨削深度和超声振幅对其磨削表面质量的影响。结果表明:与普通磨削相比,超声振动磨削的磨粒轨迹相互交叉叠加,工件表面形貌更均匀,表面质量更好。由于超声振动时的磨粒划痕交叉会使磨粒产生空切削,因而降低了其磨削力,使磨削过程更加稳定。超声振动磨削的表面粗糙度和磨削力随砂轮线速度和超声振幅的增加而降低,随工件进给速度和磨削深度的减小而降低。且砂轮线速度、工件进给速度较小时,超声振动磨削的效果更明显。   相似文献   

9.
单颗磨粒磨削钛合金TC4成屑过程仿真研究   总被引:2,自引:0,他引:2  
采用有限元模拟技术对钛合金TC4材料的单颗磨粒磨屑形成过程进行了仿真研究.研究表明:钛合金TC4在单颗磨粒磨削过程中发生绝热剪切,形成锯齿状磨屑;磨削过程中单颗磨粒磨削力成周期变化;磨粒负前角增大,锯齿化程度加深;磨削速度提高,磨屑剪切带宽度减小;仿真分析得到的磨屑形态与实验结果相一致.  相似文献   

10.
小砂轮轴向大切深缓进给磨削以较大切深实现了较高的材料去除率,且使用的砂轮直径比常规磨削用砂轮小很多,我们针对这一特点开展了研究。实验通过改变砂轮转速、工件转速和磨削深度等加工参数,对轴向大切深缓进给磨削加工后的砂轮表面进行了形貌观测和磨损分析。分析表明,砂轮各部分的磨损形式与其在磨削过程中所起的作用有关:砂轮端面是磨削加工的主磨削区,磨粒和结合剂主要发生较大程度的磨损;砂轮圆周面主要对已加工表面进行修磨,因而结合剂和磨粒磨损为主要磨损形式;砂轮拐角作为过渡磨削区,承受的磨削力也比较大,而且由于磨粒与结合剂的结合力相对较小,因此易发生磨粒和结合剂的脱落。  相似文献   

11.
In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.  相似文献   

12.
After nearly two years' tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry (SRIF), located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.  相似文献   

13.
Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.  相似文献   

14.
The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.  相似文献   

15.
The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).  相似文献   

16.
The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.  相似文献   

17.
This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.  相似文献   

18.
Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.  相似文献   

19.
A new method was introduced to achieve directional growth of Sn crystals. Microstructures in liquid(Pb)/liquid(Sn) diffusion couples were investigated under various static magnetic fields. Results show that the β-Sn crystals mainly reveal an irregular dendritic morphology without or with a relatively low static magnetic field(B0.3 T). When the magnetic field is increased to 0.5 T, the β-Sn dendrites close to the final stage of growth begin to show some directional character. With a further increase in the magnetic field to a higher level(0.8–5 T), the β-Sn dendrites have an enhanced directional growth character, but the dendrites show a certain deflection. As the magnetic field is increased to 12 T, the directional growth of the β-Sn dendrites in the center of the couple is severely destroyed. The mechanism of the directional growth of the β-Sn crystals and the deflection of the β-Sn crystals with the application of static magnetic field was tentatively discussed.  相似文献   

20.
韩磊 《腐蚀与防护》2015,36(1):84-90,94
综述了常见的电化学噪声数据处理方法,介绍了直流趋势剔除、统计分析、快速傅立叶变换(FFT)法计算功率谱密度(PSD)以及小波变换处理电化学噪声信号的基本过程,并阐释了各种数学处理及所得参数的物理意义。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号