Enhanced Molecular Alignment in Poly‐l‐Lactic Acid Nanotubes Induced via Melt‐Press Template‐Wetting

Molecular ordering in polymers can have a drastic effect on their properties and can be used to induce or enhance functionality. In the case of poly‐l ‐lactic acid (PLLA), which is a widely used polymer in biomedicine, sensors, and actuators, preferential orientation of chains can lead to significantly enhanced electromechanical properties. In this context, template‐wetting is a straightforward method of producing polymer nanostructures, which can lead to some degree of molecular order in the polymer. Template‐wetting of PLLA has not been fully explored, especially in terms of morphological and/or structural characterization. In this work, PLLA nanotubes are grown via a modification of the template‐wetting process, referred to here as melt‐press template‐wetting. The nanotubes are thoroughly characterized with wide‐angle X‐ray diffraction, isothermal differential scanning calorimetry, and polarized light optical microscopy. This characterization indicates that the polymer chains in these PLLA nanotubes are aligned parallel to the cylindrical axis of the nanotube, which may be beneficial in certain applications.     

Synthesis,Characterization and Thermal Behaviour of Guanidinium‐5‐aminotetrazolate (GA) – A New Nitrogen‐Rich Compound

This work describes the synthesis and the thermoanalytical characterization of guanidinium‐5‐aminotetrazolate (GA). GA is a new nitrogen‐rich energetic material. It is not mentioned in the chemical literature so far. The molecular structure of the compound has been determined by IR, ¹H‐, ¹³C‐ and ¹⁵N‐NMR spectroscopy. The thermal properties, the decomposition pathways and its volatile products were investigated by thermal analysis and are discussed.     

Study on the Curing Process and the Gelation of Epoxy/Anhydride System for No‐Flow Underfill for Flip‐Chip Applications

No‐flow underfill is used in the assembly of microelectronics to increase the productivity and to decrease the cost of the flip‐chip manufacturing. The curing process, especially the gelation of the no‐flow underfill, is essential for the yield and reliability of the flip‐chip assembly. A differential scanning calorimeter (DSC) and a stress rheometer are used to study the curing process of epoxy/anhydride system at different curing rates and different isothermal temperatures. The gel point is found when the storage modulus and the loss modulus of the resin measured by the rheometer equals to each other. The degree of cure (DOC) at gelation is calculated according to the results from DSC. The results indicate a strong dependence of the DOC at gelation on the heating rates and the curing temperatures. In order to further investigate the difference in the curing process at various heating rates, FTIR spectra of the resin are taken during curing. The change of different functional groups is recorded and compared. The results do not show a significant difference in the chemical structure at different heating rates. The early gelation at high heating rate/ high temperature can be caused by the structure difference in the epoxy network at the early stage of curing due to the chain initiation and propagation of the molecules in the curing process.

Dependence of gelation of the sample on the isothermal temperatures.     

Synthesis and characterization of modified bismaleimide/polysulfone semi‐interpenetrating polymer networks

The present work reports a new method of preparing semi‐interpenetrating polymer network (semi‐IPN) membranes through in situ polymerization of bismaleimide (BMI) within polysulfone (PSF). It was found that BMI could be polymerized at ambient conditions in the presence of a proton donor and PSF without the use of an initiator or a catalyst. Chemical structure characterization of these semi‐IPNs by Fourier transform infrared attenuated total reflection (FTIR‐ATR) revealed the possibility of imide cleavage and formation of amic acid when BMI polymerization was continued for a longer time while X‐ray photoelectron spectroscopy (XPS) revealed the protonation of imide nitrogen at shorter polymerization time. It was also found that size of thermoset BMI phase within the PSF thermoplastic has a significant impact on glass‐transition temperature of resulting semi‐IPN. By controlling the thermoset/thermoplastic phase separation of semi‐IPNs through dope composition and formation techniques, gas separation membranes with comparable selectivity and permeance that were up to 12 times higher than corresponding PSF membranes were formed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 369–379, 2006     

FT‐IR Study of Blends and Complexes of Poly(mono n‐alkyl itaconates) with Poly(N,N‐dimethylacrylamide) and Poly(ethyloxazoline)

Summary: This paper reports an FT‐IR study of blends and complexes of poly(mono n‐alkyl itaconates) with poly(N,N‐dimethylacrylamide) (PDMA) and poly(ethyloxazoline) (PEOX). Strong hydrogen bonding has been found and both polybases have shown similar acceptor strengths. The extent of the interassociation has been estimated by spectral curve fitting of the polybase carbonyl band. The influences of the solvent medium and alkyl side group length of the poly(mono n‐alkyl itaconate) on the interassociation extents have been discussed. Blend and complex interassociation behavior has been compared too. Results show that media influences the interassociation degree in systems with PDMA, but has negligible influence in systems with PEOX. Moreover, the interassociation degree in blends with PEOX does not depend on the length of the poly(monoalkyl itaconate) side group, while an interassociating ability loss is observed in blends with PDMA as the side group size of the polyacid increases. This different behavior is attributed to the greater interspacing between vicinal carbonyl groups in PEOX. Anyway, this band shows conformational sensitivity and reflects the conformational changes that are forced to adopt as the steric hindrances present in the medium (due to the bulky side groups of the polyacids) increase.

Auto scaled carbonyl stretching region for PMBuI/PEOX complexes.     

Preparation and characterization of maleic anhydride‐g‐polypropylene/diamine‐modified clay nanocomposites

Polypropylene (PP)/montmorillonite (MMT) nanocomposites were prepared by compounding maleic anhydride‐g‐polypropylene (MAPP) with MMT modified with α,ω‐diaminododecane. Structural characterization confirmed the formation of characteristic amide linkages and the intercalation of MAPP between the silicate layers. In particular, X‐ray diffraction patterns of the modified clay and MAPP/MMT composites showed 001 basal spacing enlargement as much as 1.49 nm. Thermogravimetric analysis revealed that the thermal decomposition of the composite took place at a slightly higher temperature than that of MAPP. The heat of fusion of the MAPP phase decreased, indicating that the crystallization of MAPP was suppressed by the clay layers. PP/MAPP/MMT composites showed a 20–35% higher tensile modulus and tensile strength compared to those corresponding to PP/MAPP. However, the elongation at break decreased drastically, even when the content of MMT was as low as 1.25–5 wt %. The relatively short chain length and loop structure of MAPP bound to the clay layers made the penetration of MAPP molecules into the PP homopolymer phase implausible and is thought to be responsible for the decreased elongation at break. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 307–311, 2005     

Synthesis of a magnesium/aluminum/iron layered double hydroxide and its flammability characteristics in halogen‐free,flame‐retardant ethylene/vinyl acetate copolymer composites

Mg–Al–Fe ternary hydrotalcites were synthesized by a coprecipitation method and characterized with powder X‐ray diffraction, Fourier transform infrared spectroscopy, and thermogravimetric analysis. The flame‐retardant effects of Mg/Al–CO₃ layered double hydroxides (LDHs) and Mg/Al/Fe–CO₃ LDHs in an ethylene/vinyl acetate copolymer (EVA) were studied with the limited oxygen index (LOI), the UL‐94 test, and the cone calorimeter test (CCT), and the thermal degradation behavior of the composites was examined by thermogravimetric analysis. The results showed that the LOI values of the EVA/(Mg/Al/Fe–CO₃ LDH) composites were basically higher than those of the EVA/(Mg/Al–CO₃ LDH) composites at the same additive level. In the UL‐94 test, there was no rating for the EVA/(Mg/Al–CO₃ LDH) composite at the 50% additive level, and a dripping phenomenon occurred. However, the EVA/(Mg/Al/Fe–CO₃ LDH) composites at the same loading level of LDHs containing a suitable amount of Fe³⁺ ion reached the V‐0 rating, the dripping phenomenon disappearing. The CCTs indicated that the heat release rate (HRR) of the EVA composites with Mg/Al/Fe–CO₃ LDHs containing a suitable amount of Fe³⁺ decreased greatly in comparison with that of the composites with Mg/Al–CO₃ LDHs. The introduction of a given amount of Fe³⁺ ion into Mg/Al–CO₃ LDHs resulted in an increase in the LOI, a decrease in the HRR, and the achievement of the UL‐94 V‐0 rating. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Morphology profiles obtained by reaction‐induced phase separation in epoxy/polysulfone/poly(ether imide) systems

The reaction‐induced phase separation in epoxy/aromatic diamine formulations simultaneously modified with two immiscible thermoplastics (TPs), poly(ether imide) (PEI) and polysulfone (PSF), has been studied. The epoxy monomer was based on the diglycidyl ether of bisphenol A (DGEBA) and the aromatic diamine was 4,4′‐methylenebis(3‐chloro 2,6‐diethylaniline) (MCDEA). Phase‐separation conversions are reported for various PSF/PEI proportions for blends containing 10 wt% total TP. On the basis of phase‐separation results, a conversion–composition phase diagram at 200 °C was compiled. This diagram was used to design particular cure cycles in order to generate different morphologies during the phase‐separation process. It was found that, depending on the PSF/PEI ratio employed, a particulate or a morphology characterized by a distribution of irregular PEI‐rich domains dispersed in an epoxy‐rich phase was obtained for initially miscible blends. Scanning electron microscopy (SEM) characterization revealed that the PEI‐rich phase exhibits a phase‐inverted structure and the epoxy‐rich matrix presents a bimodal size distribution of TP‐rich particles. For PSF/PEI ratios near the miscibility limit, slight temperature change result in morphology profiles. Copyright © 2005 Society of Chemical Industry     

Biodegradable poly(ester‐ether)s: ring‐opening polymerization of D,L‐3‐methyl‐1,4‐dioxan‐2‐one using various initiator systems

The synthesis and detailed characterization of racemic 3‐methyl‐1,4‐dioxan‐2‐one (3‐MeDX) are reported. The bulk ring‐opening polymerization of 3‐MeDX, to yield a poly(ester‐ether) meant for biomedical applications, in the presence of various initiators such as tin(II) octanoate, tin(II) octanoate/n‐butyl alcohol, aluminium tris‐isopropoxide and an aluminium Schiff base complex (HAPENAlOⁱPr) under varying experimental conditions is here detailed for the first time. Polymerization kinetics were investigated and compared with those of 1,4‐dioxan‐2‐one. The studies reveal that the rate of polymerization of 3‐MeDX is less than that of 1,4‐dioxan‐2‐one. Experimental conditions to achieve relatively high molar masses have been established. Thermodynamic parameters such as enthalpy and entropy of 3‐MeDX polymerization as well as ceiling temperature have been determined. Poly(D ,L ‐3‐MeDX) is found to possess a much lower ceiling temperature than poly(1,4‐dioxan‐2‐one). Poly(D ,L ‐3‐MeDX) was characterized using NMR spectroscopy, matrix‐assisted laser desorption ionization mass spectrometry, size exclusion chromatography and differential scanning calorimetry. This polymer is an amorphous material with a glass transition temperature of about ?20 °C. Copyright © 2010 Society of Chemical Industry     

Preparation and characterization of hyaluronan/chitosan scaffold cross‐ linked by 1‐ethyl‐3‐(3‐dimethylaminopropyl) carbodiimide

A novel biocompatible scaffold was prepared by cross‐linking hyaluronan (HA) and chitosan (CS). The carboxyl groups of HA were activated by 1‐ethyl‐3‐(3‐dimethylaminopropyl)carbodiimide (EDC) and then cross‐linked with amino groups of CS by forming amide bonds. The HA/CS scaffold thus prepared was characterized using Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and differential scanning calorimetry. FTIR spectra showed that the absorbance of the amide (1550 cm^?1) and carbonyl (1633 cm^?1) bond in the cross‐linked scaffold was stronger than that in HA or CS. SEM micrographs showed that the cross‐linked scaffold produced at low EDC concentration had an intertwisted ribbon‐like microstructure, while the product prepared at higher EDC concentration had a porous structure. The concentration of EDC in the reaction system greatly affected the structure and properties of the HA/CS scaffold. The prepared scaffold could strongly resist degradation by hyaluronidase, free radicals in vitro and stress. Copyright © 2007 Society of Chemical Industry     

Optimization of polyethylene/binder/polyamide extrusion blow‐molded films. III. Slippability improvement with fatty acid amides

The slippability of packaging films has to be controlled to facilitate confectionary operations and guarantee an easy opening for filling. In the case of single‐layer polyethylene (PE) films, the addition of slip agents made of fatty acid amides such as erucamide or oleamide usually allows the tailoring of the coefficient of friction (COF) in the film to match industrial targets, which depend on the final application. The coupling of Fourier transform infrared spectroscopy and atomic force microscopy analysis showed that this method has a limited efficiency and may even be detrimental in the case of multilayer PE + ethylene vinyl acetate (EVA)/maleic anhydride grafted polyethylene (PEgMAH) + EVA/polyamide films. The reason is that the migration of the slip additives toward the outermost surface of the PE layer, which leads to a reduction in the COF, are strongly affected by both the existence of the adjacent layers and the presence of EVA in the PE and PEgMAH layers. Nevertheless, a proper knowledge of the effect of this perturbation allows one to reach a slippability level that is required for some confectionary operations and/or for an easy opening for filling without the degradation of the heat sealability. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Surface chemistry and mechanical property changes of wood‐flour/high‐density‐polyethylene composites after accelerated weathering

Although wood–plastic composites have become more accepted and used in recent years and are promoted as low‐maintenance, high‐durability building products, they do experience a color change and a loss in mechanical properties with accelerated weathering. In this study, we attempted to characterize the modulus‐of‐elasticity (MOE) loss of photostabilized high‐density polyethylene (HDPE) and composites of wood flour and high‐density polyethylene (WF/HDPE) with accelerated weathering. We then examined how weathering changed the surface chemistry of the composites and looked at whether or not the surface changes were related to the MOE loss. By examining surface chemistry changes, we hoped to begin to understand what caused the weathering changes. The materials were left unstabilized or were stabilized with either an ultraviolet absorber or pigment. After 1000 and 2000 h of accelerated weathering, the samples were tested for MOE loss. Fourier transform infrared (FTIR) spectroscopy was employed to monitor carbonyl and vinyl group formation at the surface. Changes in the HDPE crystallinity were also determined with FTIR techniques. It was determined that structural changes in the samples (carbonyl group formation, terminal vinyl group formation, and crystallinity changes) could not be reliably used to predict changes in MOE with a simple linear relationship. This indicated that the effects of crosslinking, chain scission, and crystallinity changes due to ultraviolet exposure and interfacial degradation due to moisture exposure were interrelated factors for the weathering of HDPE and WF/HDPE composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2263–2273, 2004     

The skin‐core structure of poly(acrylonitrile‐itaconic acid) precursor fibers in wet‐spinning

The skin‐core structure of poly(acrylonitrile‐itaconic acid) [P(AN‐IA)] precursor fibers in wet‐spinning has been analyzed by the means of electron probe microanalyser (EPMA), scanning electron microscope (SEM), and transmission electron microscope. The numerical solution of Fick's second law equations for diffusion in the nascent fiber was obtained by using the Method of Lines. It has been found that [P(AN‐IA)] precursor fiber composed of four parts had remarkable skin‐core structure. The sheet‐like skin, which was compact and homogeneous, had high crystallization and highly oriented structure. However, the core with low crystallization and some voids was loose, somewhat disorderly and unsystematic. Moreover, the precursor fiber had a pillar‐like layered structure along the fiber axis. The average thickness of each layer increased gradually from the skin to the endothecium. Meanwhile, a structural model of PAN precursor fiber has been built. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Super‐Tough and Highly‐Ductile Poly(l‐lactic acid)/Thermoplastic Polyurethane/Epoxide‐Containing Ethylene Copolymer Blends Prepared by Reactive Blending

Ethylene‐methyl acrylate‐glycidyl methacrylate copolymer (E‐MA‐GMA) is employed to improve the impact toughness of poly(l ‐lactic acid) (PLLA)/thermoplastic polyurethane (TPU) blends by reactive melt‐blending. The reaction and miscibility between the components are confirmed by Fourier transform infrared spectroscopy, dynamic mechanical analysis, and differential scanning calorimetry. A super‐tough PLLA/TPU/E‐MA‐GMA multiphase blend (75/10/15) exhibits a significantly improved impact strength of 77.77 kJ m^?2, which is more than 17 times higher than that of PLLA/TPU (90/10) blend. A co‐continuous‐like TPU phase structure involving E‐MA‐GMA phase at the etched cryo‐fractured surface and the high‐orientated matrix deformation at the impact‐fractured surface are observed by scanning electron microscopy. The high‐orientated matrix deformation induced by the co‐continuous TPU phase structure is responsible for the super toughness of PLLA/TPU/E‐MA‐GMA blends.     

Characterization of Polymer‐Coated RDX and HMX Particles

Fourier transform‐infrared spectroscopy (FT‐IR) in transmission and photoacoustic detection (PAS) techniques have been used for the characterization of polymeric coating of cyclotrimethylenetrinitramine (RDX) using a fluoroelastomer (Viton^®). Although the bands of the polymer were indicated by two different techniques, the transmission (casting film) showed better evidence of absorption of fluoroelastomer for the polymer coating of the energetic material. Also attenuated total reflectance (ATR), another FT‐IR technique, has been used to analyze a cyclotetramethylenetetramine (HMX)/Viton system for the characterization of Viton bands and it showed excellent results without sample preparation.     

Surface‐enhanced infrared absorption (SEIRA) and its use in analysis of plasma‐modified surface

A thin film (<10 nm) of fine metal clusters (silver or gold) with an island form was deposited on a CaF₂ salt plate by slow vacuum thermal evaporation. Molecular layers of stearic acid, p‐nitrobenzoic acid, and m‐nitrobenzoic acid (p‐ and m‐NBA) were prepared on the thin metal film. The system was then examined by infrared spectroscopy attenuated total reflection (IR–ATR). It was found that through the interaction between the metal islands film and the electric field of the incident IR beam the infrared absorption of the molecule layers adsorbed on the islands was enhanced by a factor of 17. The surface‐enhanced IR absorption (SEIRA) also presents a selection rule. This method was then used to study the surface modification with O₂ and NH₃ plasma and the plasma polymerization of allylamine. This is the first time that SEIRA has been used in plasma investigations. A model is provided to explain the interactions between the metal islands film and the electric field of the incident IR beam in the SEIRA. The in‐plasma‐built functional groups can be further used to graft biofunctional molecules for the biomedical industry. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1231–1237, 1999     

Radiopaque,barium sulfate‐filled biomedical compounds of a poly(ether‐block‐amide) copolymer

Various radiopaque compounds of a poly (ether‐block‐amide) copolymer resin filled with fine barium sulfate particles were prepared by melt mixing. Material properties of the filled compounds were investigated using various material characterization techniques, including thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic rheometry, uniaxial tensile test, and dynamic mechanical thermal analysis (DMTA). The effects of the filler and its concentration on the measured material properties are evaluated. It has been found that in addition to its well‐known X‐ray radiopacity, the filler is quite effective in reinforcing some mechanical properties of the copolymer, including modulus of elasticity and yield strength. More interestingly, it has been observed that at low loading concentrations near 10 wt %, the filler may also act as a rigid, inorganic toughener for the copolymer by improving the postyield material extensibility of strain hardening against ultimate material fracture. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and properties of poly(ether‐ester‐amide)/poly(acrylonitrile‐co‐butadiene‐co‐styrene) antistatic blends

A novel antistatic agent poly(ether‐ester‐amide) (PEEA) based on caprolactam, polyethylene glycol, and 6‐aminocaproic acid was successfully synthesized by melting polycondensation. The structure, thermal properties, and antistatic ability of the copolymer were characterized by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analyses, and ZC36 megohmmeter. Test results show that PEEA is a block copolymer with a melting point of 217°C and a thermal decomposition temperature of 409°C, together with a surface resistivity of 10⁸ Ω/sq. Antistatic poly(acrylonitrile‐co‐butadiene‐co‐styrene) (ABS) materials were prepared by blending different content of PEEA to ABS resin. The antistatic performances, morphology, and mechanical properties were investigated. It is indicated that the surface resistivity of PEEA/ABS blends decrease with the increasing PEEA content, and the excellent antistatic performance is obtained when the antistatic agent is up to 10–15%. The antistatic performance is hardly influenced by water‐washing and relative humidity, and a permanent antistatic performance is available. The antistatic mechanism is investigated. The compatibility of the blends was studied by scanning electron microscopy images. The ladder distribution of antistatic agent is formed, and a rich phase of antistatic agent can be found in the surface layer. The elongations at break of the blend are improved with the increasing antistatic agent; the tensile strength and the notched impact strength kept almost the same. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Preparation and electrochemical capacitance of poly(pyrrole‐co‐aniline)

The copolymer of pyrrole and aniline, poly(pyrrole‐co‐aniline), has been prepared by chemical oxidation of corresponding monomer mixtures with ammonium peroxysulfate. Techniques of FTIR, SEM‐EDS, and BET surface area measurement were used to characterize the structure and morphology of the copolymer. The electrochemical properties of the copolymer were investigated by cyclic voltammetry, galvanostatic charge‐discharge, and electrochemical impedance spectroscopy. The results indicated that poly(pyrrole‐co‐aniline) was about 100–300 nm in diameter and showed better electrochemical capacitive performance than polypyrrole and polyaniline. The specific capacitance of the copolymer electrode was 827 F/g at a current of 8 mA/cm² in 1 mol/L Na₂SO₄ electrolyte. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Poly(2‐alkyloyloxyethylacrylate) and poly(2‐alkyloyloxyethylacrylate‐co‐methylacrylate) comblike polymers as novel phase‐change materials for thermal energy storage

A series of poly(2‐alkyloyloxyethylacrylate) and poly(2‐alkyloyloxyethylacrylate‐co‐methylacrylate) polymers as novel polymeric phase‐change materials (PCMs) were synthesized starting from 2‐hydroxyethylacrylate and fatty acids. The chemical structure and crystalline morphology of the synthesized copolymers were characterized with Fourier transform infrared and ¹H‐NMR spectroscopy and polarized optical microscopy, respectively, and their thermal energy storage properties and thermal stability were investigated with differential scanning calorimetry and thermogravimetric analysis, respectively. The thermal conductivities of the PCMs were also measured with a thermal property analyzer. Moreover, thermal cycling testing showed that the copolymers had good thermal reliability and chemical stability after they were subjected to 1000 heating/cooling cycles. The synthesized poly(2‐alkyloyloxyethylacrylate) polymers and poly(2‐alkyloyloxyethylacrylate‐co‐methylacrylate) copolymers as novel PCMs have considerable potential for thermal energy storage and temperature‐control applications. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012