一种采用共栅频率补偿的轨到轨输入/输出放大器

提出了一种采用共栅频率补偿的轨到轨输入/输出放大器,与传统的Miller补偿相比,该放大器不仅可以消除相平面右边的低频零点,减少频率补偿所需要的电容,还可获得较高的单位增益带宽.所提出的放大器通过CSMC 0.6μm CMOS数模混合工艺进行了仿真设计和流片测试:当供电电压为5V,偏置电流为20μA,负载电容为10pF时,其功耗为1.34mW,单位增益带宽为25MHz;当该放大器作为缓冲器,供电电压为3V,负载电容为150pF,输入2.66 Vpp10kHz正弦信号时,总谐波失真THD为-51.6dB.     

A compact rail-to-rail CMOS buffer amplifier with very low quiescent current

In this work, a very compact, rail-to-rail, high-speed buffer amplifier for liquid crystal display (LCD) applications is proposed. Compared to other buffer amplifiers, the proposed circuit has a very simple architecture, occupies a small number of transistors and also has a large driving capacity with very low quiescent current. It is composed of two complementary differential input stages to provide rail-to-rail driving capacity. The push–pull transistors are directly connected to the differential input stage, and the output is taken from an inverter. The proposed buffer circuit is laid out using Mentor Graphics IC Station layout editor using AMS 0.35 μm process parameters. It is shown by post-layout simulations that the proposed buffer can drive a 1 nF capacitive load within a small settling time under a full voltage swing, while drawing only 1.6 μA quiescent current from a 3.3 V power supply.     

一种恒跨导轨对轨CMOS运算放大器的设计

设计了一种新颖的恒跨导轨对轨CMOS运算放大器结构。输入级采用轨对轨的结构,在输入级采用4个虚拟差分对管来对输入差分对的电流进行限制,使运放的输入级跨导在工作范围内保持恒定。输出级采用前馈式AB类输出结构,以使输出达到全摆幅。仿真结果显示,在5 V电源电压和带有10 pF电容与10 kΩ电阻并联的负载下,该运放在共模输入范围内实现了恒跨导,在整个共模输入范围内跨导变化率仅为3%,输出摆幅也达到了轨对轨全摆幅,运放的开环增益为108.5 dB,增益带宽积为26.7 MHz,相位裕度为76.3°。     

低压工作的轨到轨输入／输出缓冲级放大器

本文提出了一种低压工作的轨到轨输入／输出缓冲级放大器。利用电阻产生的输入共模电平移动,该放大器可以在低于传统轨到轨输入级所限制的最小电压下工作,并在整个输入共模电压范围内获得恒定的输入跨导;它的输出级由电流镜驱动,实现了轨到轨电压输出,具有较强的负载驱动能力。该放大器在CSMCO．6-μmCMOS数模混合工艺下进行了HSPICE仿真和流片测试,结果表明：当供电电压为5V,偏置电流为60uA,负载电容为10pF时,开环增益为87．7dB,功耗为579uw,单位增益带宽为3．3MHz;当该放大器作为缓冲级时,输入3VPP10kHz正弦信号,总谐波失真THD为53．2dB。     

An adaptive biasing one-stage CMOS operational amplifier fordriving high capacitive loads

An adaptive biasing one-stage CMOS operational amplifier for driving high capacitive loads has been developed. The amplifier has been designed to drive liquid-crystal-displays (LCDs) in battery-supplied devices. Contradictory features like low power dissipation and high driving capability at low supply voltage are required. Complementary differential input stages provide rail-to-rail common-mode input range. With a special cross-coupled double-to-single-end conversion, a full supply output range is achieved. These improvements solve a functional problem of some existing adaptive biasing amplifiers. Simulation and measurements demonstrate good correlation and show the expected results, especially in the critical operating area     

Rail-to-rail BiCMOS operational amplifier using input signal adapters with floating outputs

An operational amplifier with rail-to-rail input and output voltage range in 0.6 μm BiCMOS technology is presented. Two simple input signal adapters with floating outputs serving as pre-stages are introduced. They are followed by a differential amplifier. The adapters translate the input signals into a floating level within the operating region of the differential amplifier, enabling rail-to-rail operation. An inverter-based simple rail-to-rail class AB output stage has been used. With a single supply of 1.5 V, the proposed rail-to-rail operational amplifier achieves 72 dB DC open-loop gain, 2.54 MHz unity-gain frequency, 62° phase margin, 2.5 V/μs slew rate, and 147 μW power consumption.     

High-gain,high-bandwidth,rail-to-rail,constant-gm CMOS operational amplifier

This study presents a high-gain, high-bandwidth, constant-g_m , rail-to-rail operational amplifier (op-amp). The constant transconductance is improved with a source-to-bulk bias control of an input pair. A source degeneration scheme is also adapted to the output stage for receiving wide input range without degradation of the gain. Additionally, several compensation schemes are employed to enhance the stability. A test chip is fabricated in a 0.18?µm complementary metal-oxide semiconductor process. The active area of the op-amp is 181?×?173?µm² and it consumes a power of 2.41?mW at a supply voltage of 1.8?V. The op-amp achieves a dc gain of 94.3?dB and a bandwidth of 45?MHz when the output capacitive load is connected to an effective load of 42.5?pF. A class-AB output stage combining a slew rate (SR) boost circuit provides a sinking current of 6?mA and an SR of 17?V/µs.     

Design of a 1-V High-Frequency Bipolar Operational Amplifier

This paper presents the design of a low-voltage high-frequency operational amplifier implemented in bipolar technology. The minimum power supply voltage for this amplifier can be as low as 0.9 V, so it is suitable for portable equipment applications. The design emphasis is on the high frequency response. A pole-zero cancellation compensation technique and a special low-voltage design gives a simulated cutoff frequency of about 175 MHz with a 50° phase margin at a power supply voltage of ±0.5 V with a 10 k load resistance; the low-frequency voltage gain is 110 dB. The common-mode input range includes, and can exceed, the negative supply voltage by about 400 mV. A complimentary class-B type output stage enables the output voltage to reach both supply rails within about 100 mV without significant signal distortion. This amplifier dissipates 875 W.     

基于GaN HEMT的1.5～3.5GHz宽带平衡功率放大器设计

阐述了基于GaN HEMT的宽带平衡功率放大器的设计与实现方法:采用Lange耦合器构建平衡功率放大器结构,采用多节阻抗匹配技术设计输入/输出匹配网络,实现功放宽带特性(1.5～3.5GHz);采用与Si热膨胀系数接近的AlSiC散热载片,克服管芯与载片热稳定系数不同引起的热稳定问题,并采用脉冲工作模式进一步减小功放发热量.制作实际功放模块用于测试,在1.5～3.5GHz频带内,功放线性增益大于12dB,增益平坦度为±0.4dB,饱和输出功率大于8W,漏极效率为56%～65%.实验测试结果与设计仿真结果有较好一致性,验证了设计方法的正确性.     

Class AB CMOS amplifiers with high efficiency

A new class AB CMOS operational-amplifier principle is presented. A transconductance amplifier based on this principle exhibits small-signal characteristics comparable to those of a conventional OTA. It has, however, a superior current efficiency and its settling time is not slew-rate limited. The new class AB principle can also be used in an output stage with a well-defined quiescent current, a rail-to-rail output swing, and a good driving capability. A two-stage amplifier with both the input and output stages based on the new principle has been realized. It features a rail-to-rail input and output common-mode range, a gain-bandwidth of 370-kHz, a settling time of less than 5 μs independent of the applied step, and a power consumption of 247 μW. It drives a resistive load of 3 kΩ in parallel with a capacitive load of 400 pF when operated on a 2.5-V/-2.5-V power supply     

Low-power high-speed rail-to-rail LCD output buffer with dual-path push–pull operation and quiescent current control

The present paper addresses a new compact low-power high-speed output buffer amplifier topology for large-size liquid crystal display applications. The suggested buffer achieves fast driving performance, draws a low quiescent current during static operation and offers a rail-to-rail common-mode input range. The circuit provides enhanced slewing capabilities with a limited power consumption by simultaneously exploiting the push–pull output sections of two basic complementary-type input amplifiers to realize a dual-path push–pull operation of the output stage. An auxiliary biasing network integrated in the input differential stage allows the quiescent bias conditions of the class-AB output stage to be inherently controlled without additional current dissipation. Post-layout simulation results confirm that the proposed amplifier can drive a 1-nF column line load within a 0.9-μs settling time under a 3-V full voltage swing, while drawing only 3.5-μA quiescent current. Monte Carlo simulations are finally carried out, showing a good degree of robustness of the proposed output buffer against process and mismatch variations.     

A high efficiency PWM CMOS class-D audio power amplifier

Based on the difference close-loop feedback technique and the difference pre-amp, a high efficiency PWM CMOS class-D audio power amplifier is proposed. A rail-to-rail PWM comparator with window function has been embedded in the class-D audio power amplifier. Design results based on the CSMC 0.5 μm CMOS process show that the max efficiency is 90%, the PSRR is -75 dB, the power supply voltage range is 2.5-5.5 V, the THD+N in 1 kHz input frequency is less than 0.20%, the quiescent current in no load is 2.8 mA, and the shutdown current is 0.5 μA. The active area of the class-D audio power amplifier is about 1.47 × 1.52 mm2. With the good performance, the class-D audio power amplifier can be applied to several audio power systems.     

A high current drive CMOS output stage with a tunable quiescent current limiting circuit

A CMOS output stage based on a complementary common source with an original quiescent current limiting circuit is presented. The quiescent current can be varied over a wide range by means of a control current with no need to modify the transistor aspect ratios. The output stage has been coupled to a conventional complementary input stage to form a rail-to-rail buffer. A prototype with the inclusion of auxiliary pins for biasing and current monitoring purposes has been designed using the 1-/spl mu/m double-polysilicon BCD3S process of STMicroelectronics. On a single 5-V power supply, the maximum output current is 20 mA. The amplifier, biased for a total power dissipation of 1 mW, exhibits a total harmonic distortion of -58 dB at 1 kHz with 4-V peak-to-peak on a 330-/spl Omega/ load. Correct operation of the quiescent current limiting circuit has been demonstrated for a minimum supply voltage of 2.2 V.     

Electronically tunable CMOS class-AB output stage

A new technique for CMOS class-AB output stages is introduced in this Letter. The technique uses a master–slave configuration of a complementary common-source output stage. It offers the advantage that the quiescent and minimum currents of the output stage can be independently tuned. The effectiveness of the proposed technique was verified by simulations using a standard n-well 0.18 μm CMOS process with 1 V supply voltage. A voltage buffer, that includes the proposed output stage, is able to drive a capacitive load of 0.5 nF obtaining −63 dB total harmonic distortion. The topology features also power efficiency of about 63% for a pure resistive output load equal to 50 Ω.     

A Low-Voltage Fully Differential Constant-Gm Rail-to-Rail CMOS Operational Amplifier

A low-voltage fully differential CMOS operational amplifier withconstant-g_mand rail-to-rail input and output stages ispresented. It is the fully differential version of a previously realizedsingle-ended operational amplifier where a novel circuit to ensure constanttransconductance has been implemented [1]. The input stage is a rail-to-railstructure formed by two symmetrical OTAs in parallel (the input transistorsare operating in weak inversion). The class-AB output stages have also afull voltage swing. A rail-to-rail input common mode feedback structureallows the output voltage control. Measurements in a 0.7 µ standardCMOS process with threshold voltages of about 0.7 V have been done. Theminimum experimental supply voltage is about 1.1 V. The circuit provides a60 dB low frequency voltage gain and about 1.5 MHz unity gain frequency fora total power consumption of about 0.72 mW at a 1.5 V supply voltage.     

一种用于视频信号处理的高速宽带运算放大器

基于高速亚微米互补双极工艺,设计了一种用于视频信号处理的高速宽带运算放大器。电路内部采用高速输入差分对、电流型放大单元、Rail-to-Rail输出单元等结构进行信号传输和放大。对开环增益提升、高速电压-电流信号转换、满摆幅输出设计以及频率稳定性补偿等关键技术进行分析,利用Spectre软件进行仿真。流片后的测试结果表明,在±5 V工作电压下,该放大器的－3 dB带宽≥200 MHz,失调电压≤5 mV,电源电流≤6 mA,满足高速通信、高速ADC前端信号采集、视频信号处理等各种场合的应用需求。     

High-speed driving scheme and compact high-speed low-power rail-to-rail class-B buffer amplifier for LCD applications

A high-speed driving scheme and a compact high-speed low-power rail-to-rail class-B buffer amplifier, which are suitable for small- and large-size liquid crystal display applications, are proposed. The driving scheme incorporates two output driving stages in which the output of the first output driving stage is connected to the inverting input and that of the second driving stage is connected to the capacitive load. A compensation resistor is connected between the two output stages for stability. The second output stage is used to improve the slew rate and the settling time. The buffer draws little current while static but has a large driving capability while transient. The circuit achieves the large driving capability by employing simple comparators to sense the transients of the input to turn on the output stages, which are statically off in the stable state. This increases the speed of the circuit without increasing static power consumption too much. A rail-to-rail folded-cascode differential amplifier is used to amplify the input signal difference and supply the bias voltages for the second stage. An experimental prototype output buffer implemented in a 0.35-/spl mu/m CMOS technology demonstrates that the circuit draws only 7-/spl mu/A static current and exhibits the settling times of 2.7 /spl mu/s for rising and 2.9 /spl mu/s for falling edges for a voltage swing of 3.3 V under a 600-pF capacitance load with a power supply of 3.3 V. The active area of this buffer is only 46.5/spl times/57/spl mu/m/sup 2/.     

一种恒跨导CMOS运算放大器的设计

设计了一种宽带轨对轨运算放大器,此运算放大器在3.3 V单电源下供电,采用电流镜和尾电流开关控制来实现输入级总跨导的恒定。为了能够处理宽的电平范围和得到足够的放大倍数,采用用折叠式共源共栅结构作为前级放大。输出级采用AB类控制的轨对轨输出。频率补偿采用了级联密勒补偿的方法。基于TSMC 2.5μm CMOS工艺,电路采用HSpice仿真,该运放可达到轨对轨的输入/输出电压范围。     

A 1-V BiCMOS rail-to-rail amplifier with n-channel depletion modeinput stage

A BiCMOS rail-to-rail operational amplifier capable of operating from supply voltages as low as 1 V is presented. The folded cascode input stage uses an nMOS depletion mode differential pair to provide rail-to-rail common mode voltage range while typically requiring only 40 fA of input bias current. The bipolar transistor differential-to-single-ended conversion network employs a low-voltage base current cancellation technique which provides high input stage voltage gain from a l-V supply yet allows a 3-V/μs slew rate capability. The bipolar transistor output stage uses a low-voltage translinear loop which maintains a low impedance signal path to the output common emitter power devices. This circuit topology enables the amplifier to achieve a 4-MHz bandwidth with 60° of phase margin. The output voltage can swing to within 50 mV of each supply rail. An “on-demand” base current boost technique will be presented which can provide up to 50 mA of output drive capability from a 5-V supply, yet consumes only a few microamps when the output is in the quiescent state. A low voltage level shift technique will be described which uses an n-channel depletion mode source follower to provide isolation between the input and output stages     

A novel tunable gain CMOS buffer amplifier for large resistive loads

An all-OTA analog buffer amplifier configuration capable of driving large resistive loads is presented. The proposed configuration features high input swing, gain tunability, wide-bandwidth, and low design complexity. The concept is validated with simulation results in Cadence Virtuoso using SCL 0.18-μm technology parameters. Using a ±0.9 V power supply, the buffer with a gain of 1, can drive a 1 V_p−p sinusoid into a 50 Ω load with a THD of better than 0.015%, with a 3-dB bandwidth of 1.55 GHz and consumes 9 mW. The proposed configuration is demonstrated with gain values varying from 0.25 V/V to 5 V/V and with different load values 16 Ω to 5.6 kΩ. The voltage gain is tunable over more than a decade with reasonable power levels. With low-gain OTA, the proposed buffer configuration works well without any complex frequency compensation circuit that makes the all-OTA analog buffer amplifier configuration simple compared to the existing buffer amplifiers.