Preparation and characterization of semiconducting Zn1−xCdxSe thin films

The electrodeposition of Zn_1−xCd_xSe polycrystalline semiconducting thin films from aqueous acidic bath without any additives onto tin oxide-coated conducting glass and titanium substrates are described. The influence of deposition parameters on the film formation and deposition mechanism based on cyclic voltammetry is discussed. X-ray diffraction studies showed the polycrystalline wurtzite nature for all the films deposited under the proposed conditions. The optical studies revealed the band gap values in the range between 2.82 and 1.72 eV as the film composition changes from ZnSe to CdSe. It has been observed that the concentration of cadmium salt plays an essential role on the alloy formation. The surface morphological studies and composition analysis were carried out and the results are discussed.     

Investigation of non-aqueous electrodeposited CdS/Cd1−xZnxTe heterojunction solar cells

Polycrystalline Cd_1−xZn_xTe solar cells with efficiency of 8.3% were grown by cathodic electrodeposition on glass/ITO/CdS substrates using non-aqueous ethylene glycol bath. The deposit is characterised versus the process conditions by XRD and found to possess a preferred (1 1 1) orientation on Sb doping in the electroplating bath. The surface morphology of the deposit is studied using atomic force microscope. The average RMS roughness for the ternary film was higher than that for the binary CdTe. Optical properties of the films were carried out to study the band gap and calculation of molar concentration ‘x’. The effects of Sb doping in CdS/Cd_1−xZn_xTe heterojunctions have been studied. The short circuit current density (c) was found to improve and series resistance (R_s) reduced drastically upon Sb doping. This improvement in J_sc is attributed to an increase in quantum efficiency. The evaluation of solar cell parameters was also carried out using the current–voltage characteristics in dark and illumination. The best results were obtained when 2×10⁻³ M ZnCl₂ along with antimony were present in the deposition bath. Under AM 1.5 conditions the open circuit voltage, short circuit current density, and fill factor of our best cell were V_oc=600 mV, J_sc=26.66 mA/cm², FF=0.42 and efficiency, η=8.3%. The carrier concentration and built-in potential of Cd_1−xZn_xTe calculated from Mott–Schottky plot was 2.72×10¹⁷ cm⁻³ and 1.02 eV.     

Sputtered Cd1−xZnxTe films for top junctions in tandem solar cells

Cd_1−xZn_xTe alloy films with 1.6 and 1.7 eV band gaps were deposited by RF magnetron sputtering from targets made either of mixed powders or alloys of CdTe and ZnTe (25% and 40%). High-quality polycrystalline films with the (1 1 1) preferred orientation were obtained. The films were characterized using X-ray diffraction (XRD), scanning electron microscopy, resistivity, optical absorption, Raman, and photoluminescence. The EDS, XRD, and optical absorption analysis indicated that the x-value of the as-grown films were typically 0.20 and 0.30 for films sputtered from 25% and 40% ZnTe containing targets, respectively. The as-deposited alloy films exhibit quite low photovoltaic performance when used to make cells with CdS as the hetero-junction partner. Therefore, we have studied various post-deposition treatments with vapors of chlorine-containing materials, CdCl₂ and ZnCl₂, in dry air or H₂/Ar ambient at 390 °C. The best performance of a Cd_1−xZn_xTe cell (, ) was found for treatment with vapors of the mixed CdCl₂+0.5%ZnCl₂ in an H₂/Ar ambient after pre-annealing at 520 °C in pure H₂/Ar.     

Structural and optical characterization of hot wall deposited CdSexTe1−x films

CdSe_0.3Te_0.7 alloy was prepared from the individual components and its composition and structural analysis were done. Films were prepared by hot wall deposition technique using 0.15 m length tube under a vacuum of 5×10⁻⁵ Torr on well cleaned glass substrates. The composition, structural, morphological, and optical properties of hot wall deposited films were investigated. The XRD analysis revealed that the films are like amorphous in nature for lower thicknesses but with increasing thickness a more preferred orientation along (1 0 1) direction was observed. The crystallite size (D), dislocation density (δ) and strain () were evaluated. From the EDX composition analysis, the individual concentrations of Se and Te in the films were estimated. An analysis of optical measurements shows that all the films have fairly good transparency above 850 nm. The optical band gap was found to be around 1.55 eV and decreases with increasing thickness. Also comparison of band gap with corresponding values for CdSe and CdTe are made.     

New trends to grow the n-CdZn (S1−xSex)2/p-CuIn(S1−xSex)2 heterojunction thin films for solar cell applications

The n-CdZn(S_1−xSe_x) and p-CuIn(S_1−xSe_x)₂ thin films have been grown by the solution growth technique (SGT) on glass substrates. Also the heterojunction (p–n) based on n-CdZn (S_1−xSe_x)₂ and p-CuIn (S_1−xSe_x)₂ thin films fabricated by same technique. The n-CdZn(S_1−xSe_x)₂ thin film has been used as a window material which reduced the lattice mismatch problem at the junction with CuIn (S_1−xSe_x)₂ thin film as an absorber layer for stable solar cell preparation. Elemental analysis of the n-CdZn (S_1−xSe_x)₂ and p-CuIn(S_1−xSe_x)₂ thin films was confirmed by energy-dispersive analysis of X-ray (EDAX). The structural and optical properties were changed with respect to composition ‘x’ values. The best results of these parameters were obtained at x=0.5 composition. The uniform morphology of each film as well as the continuous smooth thickness deposition onto the glass substrates was confirmed by SEM study. The optical band gaps were determined from transmittance spectra in the range of 350–1000 nm. These values are 1.22 and 2.39 eV for CuIn(S_0.5Se_0.5)₂ and CdZn(S_0.5Se_0.5)₂ thin films, respectively. J–V characteristic was measured for the n-CdZn(S_1−xSe_x)₂/p-CuIn(S_1−xSe_x)₂ heterojunction thin films under light illumination. The device parameters V_oc=474.4 mV, J_sc=13.21 mA/cm², FF=47.8% and η=3.5% under an illumination of 85 mW/cm² on a cell active area of 1 cm² have been calculated for solar cell fabrication. The J–V characteristic of the device under dark condition was also studied and the ideality factor was calculated which is equal to 1.9 for n-CdZn(S_0.5Se_0.5)₂/p-CuIn(S_0.5Se_0.5)₂ heterojunction thin films.     

Deposition of highly photoconductive wide band gap a-SiOx:H thin films at a high temperature without H2-dilution

Electrical and optical characterisation of hydrogenated amorphous silicon–oxygen alloy thin films (a-SiO_x:H, x<2) grown in a single chamber radio frequency plasma enhanced chemical vapour deposition (PECVD) system at a high substrate temperature of 300 °C is presented. The samples were investigated by Fourier transform infrared spectroscopy (FTIR), optical transmission, the constant photocurrent method (CPM), conductivity and steady-state photoconductivity measurements. With increasing oxygen concentration, the Tauc gap increases from 1.69 to 2.73 eV. The sample with an oxygen concentration of 26.2 at% and a reasonably high bandgap of 2.18 eV shows photoconductivity comparable to that of pure a-Si:H films. The Urbach parameter (E₀) increases almost linearly with oxygen concentration whereas the dangling bond defect density is found to be saturating at a value of about 7.1×10¹⁶ cm⁻³. One of the highly alloyed samples with exhibited a detectable photosensitivity.     

Pyrite (FeS2) thin films prepared by spray method using FeSO4 and (NH4)2Sx

A simple spray method for the preparation of pyrite (FeS₂) thin films has been studied using FeSO₄ and (NH₄)₂S_x as precursors for Fe and S, respectively. Aqueous solutions of these precursors are sprayed alternately onto a substrate heated up to 120°C. Although Fe–S compounds including pyrite are formed on the substrate by the spraying, sulfurization of deposited films is needed to convert other phases such as FeS or marcasite into pyrite. A single-phase pyrite film is obtained after the sulfurization in a H₂S atmosphere at around 500°C for 30 min. All pyrite films prepared show p-type conduction. They have a carrier concentration (p) in the range 10¹⁶–10²⁰ cm⁻³ and a Hall mobility (μ_H) in the range 200–1 cm²/V s. The best electrical properties (p=7×10¹⁶ cm⁻³, μ_H=210 cm²/V s) for a pyrite film prepared here show the excellence of this method. The use of a lower concentration FeSO₄ solution is found to enhance grain growth of pyrite crystals and also to improve electrical properties of pyrite films.     

Characterization and electrochromic properties of CuxNi1−xO films prepared by sol–gel dip-coating

Cu_xNi_1−xO electrochromic thin films were prepared by sol–gel dip coating and characterized by XRD, UV–vis absorption and electrochromic test. XRD results show that the structure of the Cu_x Ni_1−xO thin films is still in cubic NiO structure. UV–vis absorption spectra show that the absorption edges of the Cu_xNi_1−xO films can be tuned from 335 nm (x = 0) to 550 nm (x = 0.3), and the transmittance of the colored films decrease as the content of Cu increases. Cu_xNi_1−xO films show good electrochromic behavior, both the coloring and bleaching time for a Cu_0.2Ni_0.8O film were less than 1 s, with a variation of transmittance up to 75% at the wavelength of 632.8 nm.     

Preparation of CuIn1−xGaxSe2 thin films by sputtering and selenization process

CuIn_1−xGa_xSe₂ polycrystalline thin films were prepared by a two-step method. The metal precursors were deposited either sequentially or simultaneously using Cu–Ga (23 at%) alloy and In targets by DC magnetron sputtering. The Cu–In–Ga alloy precursor was deposited on glass or on Mo/glass substrates at either room temperature or 150°C. These metallic precursors were then selenized with Se pellets in a vacuum furnace. The CuIn_1−xGa_xSe₂ films had a smooth surface morphology and a single chalcopyrite phase.     

Structural and photoluminescence study of the quaternary alloys system CuIn(SxSe1−x)2

The full composition range CuIn(S_xSe_1−x)₂ alloy system has been studied using 40 mm length crystal cuts from 10 mm diameter ingots grown by the classical Bridgman method. X-ray diffraction diffractographs show that the CuIn(S_xSe_1−x)₂ compounds have a chalcopyrite structure for each composition x, they exhibit an expansion on the unit cell characteristics by the tetragonal distortion which depends linearly on the electronegativity of the atoms. The photoluminescence spectra is investigated as a function of various compositions, temperature and excitation intensities. Photoluminescence spectra shows a wide variation in the dominant peak location and an overall blue shift with the increase of sulphur content. Photoluminescence CuInS₂ and CuIn(S_0.72Se_0.28)₂ have been studied in detail.     

PtxNi1−x nanoparticles as catalysts for hydrogen generation from hydrolysis of ammonia borane

We report on Pt_xNi_1−x (x = 0, 0.35, 0.44, 0.65, 0.75, and 0.93) nanoparticles as catalysts for hydrogen generation from hydrolysis of ammonia borane (NH₃BH₃). The Pt_xNi_1−x catalysts were prepared through a redox replacement reaction with a reverse microemulsion technique. The structure, morphology, and chemical composition of the obtained samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) equipped with energy dispersive X-ray (EDX), and inductively coupled plasma emission spectroscopy (ICP). The results show that the diameters of the Pt_xNi_1−x nanoparticles are about 2–4 nm, and the Pt atomic contents in the catalysts were 35%, 44%, 65%, 75%, and 93%, respectively. It is found that the catalytic activity toward the hydrolysis of NH₃BH₃ is correlated with the composition of the Pt_xNi_1−x catalysts. The annealing of Pt_0.65Ni_0.35 at 300 °C for 1 h increases the crystallinity of the nanoparticles, but shows almost the same activity as that without annealing. Among the as-prepared Pt_xNi_1−x nanoparticles, Pt_0.65Ni_0.35 displays the highest catalytic performance, delivering a high hydrogen-release rate of 4784.7 mL min⁻¹ g⁻¹ and a low activation energy of 39.0 kJ mol⁻¹.     

Optical, electrical and structural investigations on Cd1−xZnxSe sintered films for photovoltaic applications

II–VI polycrystalline semiconducting materials have come under increased scrutiny because of their wide use in the cost reduction of devices for photovoltaic applications. Cd_1−xZn_xSe is an important semiconducting alloy because of the tunability of its physical parameters such as band gap and lattice parameters by controlling its stoichiometry. Many more material characteristics of it would be altered and excellently controlled by controlling system composition x.Polycrystalline thin films of Cd_1−xZn_xSe with variable composition (0x1) have been deposited onto ultra-clean glass substrates by sintering process. The optical, structural and electrical transport properties of Cd_1−xZn_xSe thin films have been examined. The optical band gap and optical constants of these films were determined by using double beam spectrophotometer. The DC conductivity and activation energy of the films were measured in vacuum by two-probe technique. The Schottky junction of Cd_1−xZn_xSe with indium was made and the barrier height and ideality factor were determined using current–voltage characteristics. The nature of sample, crystal structure and lattice parameters were determined from X-ray diffraction patterns. The films were polycrystalline in nature having cubic zinc-blende structure over the whole range studied.Sintering is very simple and viable compared to other cost intensive methods. The results of the present investigation will be useful in characterizing the material, Cd_1−xZn_xSe, for its applications in photovoltaics.     

Properties of CuIn1−xGaxSe2

Polycrystalline bulk samples of CuIn_1−xGa_xSe₂ weregrown with nominal x = 0.15, 0.25 and 0.5. Mobility, conductivity and band gap were measured at room and low temperatures. Mobilities for x = 0.21 were several hundred cm² V⁻¹s⁻¹ at room temperature and for x = 0.15 were 10³ cm² V⁻¹ s⁻¹, all n type. The band gaps were estimated from the spectra of photoelectrochemical cells at room temperature (with 8.5 K photoluminescence estimates shown in brackets), as 1.10 eV (1.14) for x = 0.21, and 1.07 eV (1.093) for x = 0.15. Crystal mechanical properties as regards cracks were not as good as for CuInSe₂, using similar growth techniques.     

Highly conducting transparent nanocrystalline Cd1−xSnxS thin film synthesized by RF magnetron sputtering and studies on its optical, electrical and field emission properties

Transparent conducting Cd_1−xSn_xS thin films have been synthesized by radio frequency magnetron sputtering technique on glass and Si substrates for various tin concentrations in the films. X-ray diffraction studies showed broadening of peaks due to smaller crystal size of the Cd_1−xSn_xS films, and SEM micrographs showed fine particles with average size of 100 nm. Sn concentration in the films was varied from 0% to 12.6% as determined from energy-dispersive X-ray analysis. The room-temperature electrical conductivity was found to vary from 8.086 to 939.7 S cm⁻¹ and corresponding activation energy varied from 0.226 to 0.076 eV. The optimum Sn concentration for obtaining maximum conductivity was found to be 9.3%. The corresponding electrical conductivity was found to be 939.7 S cm⁻¹, and the mobility 49.7 cm² V⁻¹ s⁻¹. Hall measurement showed very high carrier concentrations in the films lying in the range of 8.0218×10¹⁸–1.7225×10²⁰ cm⁻³. The conducting Cd_1−xSn_xS thin films also showed good field emission properties with a turn on field 4.74–7.86 V μm⁻¹ with variation of electrode distance 60–100 μm. UV–Vis–NIR spectrophotometric studies of the films showed not needed the optical band gap energy increased from 2.62 to 2.80 eV with increase of Sn concentration in the range 0–12.6%. The optical band gap was Burstein–Moss shifted, and the corresponding carrier concentration obtained from the shift also well matched with that obtained from Hall measurement.     

Third generation multi-layer graded band gap solar cells for achieving high conversion efficiencies—II: Experimental results

New designs of multi-layer graded band gap solar cell structures were experimentally tested using well-understood Al_xGa_(1−x)As materials grown by the MOVPE technique. Laboratory scale devices (0.5 mm diameter) were processed and measured for their performance as solar cells. Both V_oc (1110 mV) and fill factors (83%) for the best devices have shown drastic improvements over existing cells and the short-circuit current densities measured are in the range (10–20) mA cm⁻² .     

Synthesis and assessment of La0.8Sr0.2ScyMn1−yO3−δ as cathodes for solid-oxide fuel cells on scandium-stabilized zirconia electrolyte

Perovskite-type La_0.8Sr_0.2Sc_yMn_1−yO_3−δ oxides (LSSMy, y = 0.0–0.2) were synthesized and investigated as cathodes for solid-oxide fuel cells (SOFCs) containing a stabilized zirconia electrolyte. The introduction of Sc³⁺ into the B-site of La_0.8Sr_0.2MnO_3−δ (LSM) led to a decrease in the oxides’ thermal expansion coefficients and electrical conductivities. Among the various LSSMy oxides tested, LSSM0.05 possessed the smallest area-specific cathodic polarization resistance, as a result of the suppressive effect of Sc³⁺ on surface SrO segregation and the optimization of the concentration of surface oxygen vacancies. At 850 °C, it was only 0.094 Ω cm² after a current passage of 400 mA cm⁻² for 30 min, significantly lower than that of LSM (0.25 Ω cm²). An anode-supported cell with a LSSM0.05 cathode demonstrated a peak power density of 1300 mW cm⁻² at 850 °C. The corresponding value for the cell with LSM cathode was 450 mW cm⁻² under the same conditions. The LSSM0.05 oxide may potentially be a good cathode material for IT-SOFCs containing doped zirconia electrolytes.     

Synthesis and transport properties of prospective photovoltaic systems related to CuInSe2 and CuGaSe2

Solid solutions in CuGaSe₂–ZnSe and CuInSe₂–ZnSe systems have been obtained by radio frequency heating. In order to prepare n-type phases based on CuGaSe₂, p-type (CuGa)_1−xZn_2xSe₄ and (CuIn)_1−xZn_2xSe₄ (0.05x0.1) single crystals were doped by Ag, Hg, Cd, Zn implantation. The crystal structure of the solid solutions was studied by X-ray diffraction; the substitutors as well as the implantant valence states were analyzed using X-ray photoelectron spectroscopy. Hall effect, electrical conductivity, and the charge carrier mobility of an n-type zinc-implantated solid solution (CuGa)_1−xZn_2xSe₄ and (CuIn)_1−xZn_2xSe₄ (0.05x0.1) were studied.     

Optical and electrical studies on molybdenum sulphoselenide [Mo(S1−xSex)2] thin films prepared by arrested precipitation technique (APT)

Nanocrystalline stoichiometric [Mo(S_1−xSe_x)₂] thin films were deposited by using arrested precipitation technique (APT) developed in our laboratory. The precursors used for this are namely, molybdenum triethanolamine complex, thioacetamide and sodium selenosulphite; and various preparative conditions are finalised at the initial stages of deposition. Formation of [Mo(S_1−xSe_x)₂] semiconducting thin films are confirmed by studying growth mechanism, optical and electrical properties. X-ray diffraction analysis showed that the composites are nanocrystalline being mixed ternary chalcogenides of the general formula [Mo(S_1−xSe_x)₂]. The optical studies revealed that the films are highly absorptive (α×10⁴ cm⁻¹) with a band-to-band direct type of transitions and the energy gap decreased typically from 1.86 eV for pure MoS₂ down to 1.42 eV for MoSe₂. The thermoelectrical power measurement shows negative polarity for the generated voltage across the two ends of semiconductor thin films. This indicate that the [Mo(S_1−xSe_x)₂] thin film samples show n-type conduction.     

Enhanced performance of solid oxide fuel cells with Ni/CeO2 modified La0.75Sr0.25Cr0.5Mn0.5O3−δ anodes

The optimization of electrodes for solid oxide fuel cells (SOFCs) has been achieved via a wet impregnation method. Pure La_0.75Sr_0.25Cr_0.5Mn_0.5O_3−δ (LSCrM) anodes are modified using Ni(NO₃)₂ and/or Ce(NO₃)₃/(Sm,Ce)(NO₃)_x solution. Several yttria-stabilized zirconia (YSZ) electrolyte-supported fuel cells are tested to clarify the contribution of Ni and/or CeO₂ to the cell performance. For the cell using pure-LSCrM anodes, the maximum power density (P_max) at 850 °C is 198 mW cm⁻² when dry H₂ and air are used as the fuel and oxidant, respectively. When H₂ is changed to CH₄, the value of P_max is 32 mW cm⁻². After 8.9 wt.% Ni and 5.8 wt.% CeO₂ are introduced into the LSCrM anode, the cell exhibits increased values of P_max 432, 681, 948 and 1135 mW cm⁻² at 700, 750, 800 and 850 °C, respectively, with dry H₂ as fuel and air as oxidant. When O₂ at 50 mL min⁻¹ is used as the oxidant, the value of P_max increases to 1450 mW cm⁻² at 850 °C. When dry CH₄ is used as fuel and air as oxidant, the values of P_max reach 95, 197, 421 and 645 mW cm⁻² at 750, 800, 850 and 900 °C, respectively. The introduction of Ni greatly improves the performance of the LSCrM anode but does not cause any carbon deposit.     

Properties of brush plated CdxZn1−xTe thin films

Cd_xZn_1−xTe (0  x  0.5) thin films were deposited for the first time by the brush plating technique using cadmium sulphate, zinc sulphate and tellurium dioxide precursors. The deposition current density was maintained at 100 mA cm⁻². X-ray diffraction studies indicated the formation of cubic phase with (1 1 1), (2 2 0), (3 1 1) orientations. From optical absorption measurements the band gaps of the films are found to be direct. AFM studies indicate a surface roughness around 54 Å. Density of the films of different composition has been estimated. Laser Raman studies indicated CdTe like LO and TO phonons.