Catalytic activity of PdO/ZrO2 catalyst for methane combustion

Catalytic activity of ZrO₂ supported PdO catalysts for methane combustion has been investigated in comparison with Al₂O₃ supported PdO catalysts. It was found that the drop of catalytic activity owing to decomposition of PdO at a high temperature region (600–900°C) was suppressed by using ZrO₂ support. Temperature-programmed reduction (TPR) measurements of the catalyst with hydrogen revealed that the PdO of PdO/Al₂O₃ catalyst was reduced at the temperature less than 100°C, whereas in PdO/ZrO₂ catalyst the consumption of hydrogen was also observed at 200–300°C. This result indicates that the stable PdO species were present in the PdO/ZrO₂ catalyst. In order to confirm the formation of the solid solution of PdO and ZrO₂, X-ray diffraction (XRD) analyses of the mixtures of ZrO₂ and PdO calcined at 700–900°C in air were carried out. The lattice volume of ZrO₂ in the mixture was larger than that of ZrO₂. Furthermore, the Pd thin film on ZrO₂ substrate was prepared as a model catalyst and the depth profile of the elements in the Pd thin film was measured by Auger electron spectroscopy (AES). It was confirmed that Zr and O as well as Pd were present in the Pd thin film heated at 900°C in air. It was considered that the PdO on ZrO₂ support might be stabilized by the formation of the solid solution of PdO and ZrO₂.     

Partial oxidation of methane to synthesis gas over iridium–nickel bimetallic catalysts

Partial oxidation of methane to synthesis gas was carried out using supported iridium–nickel bimetallic catalysts, in order to reduce loading levels of iridium and nickel, and to avoid carbon deposition on nickel-based catalysts by adding iridium. The performance of supported iridium–nickel bimetallic catalysts in synthesis gas formation depended strongly upon the support materials. La₂O₃ gave the best performance among the support materials tested. Ir(0.25 wt%)–Ni(0.5 wt%)/La₂O₃ afforded 36% conversion of methane (CH₄/O₂=5) to give CO and H₂ with the selectivities of above 90% at 800°C, and those at 600°C were 25.3% conversion of methane and CO and H₂ selectivities of about 80%, respectively. Reduced monometallic Ir(0.25 wt%)/La₂O₃ and Ni(0.5 wt%)/La₂O₃ catalysts did not produce synthesis gas at 600°C. A higher conversion of methane was obtained by synergistic effects. The product concentrations of CO, H₂, and CO₂, and CH₄ conversion were maintained in high values, even increasing the space velocity of feed gas over Ir–Ni/La₂O₃ catalyst, indicating that rapid reaction takes place. As a by-product, a small amount of carbon deposition was observed, but carbon formation decreased with increasing the space velocity. On the other hand, with reduced monometallic Ni(10 wt%)/La₂O₃ catalyst, yield of synthesis gas and carbon decreased with increasing the space velocity.     

Catalytic clean-up of emissions from small-scale combustion of biofuels

A knitted silica-fibre was prepared and used as support for combustion catalysts. Different Pd–MeO and Pt–MeO (Me=Ni, Co, Cu and Mn) catalysts were prepared, and their catalytic activities were investigated in the conversion of gas mixtures consisting of methane, ethene, naphthalene (model PAH), carbon monoxide, carbon dioxide, nitrogen and water vapour in the temperature range 150–800°C. Combinations of Pd–Ni and Pt–Ni were found to result in decreased light-off temperatures in methane combustion. The Pd–Ni/silica-fibre catalyst exhibited a light-off temperature in methane combustion of ca 220°C lower than that obtained over the Pd/silica-fibre catalyst. Deactivation of the catalysts was observed by subjecting the catalysts to reaction mixture flow at 800°C for 6 h. For the Pd-containing catalysts, the deactivation was considered to be due to both support and metal sintering as well as changes in the nature of the Pd–O species. The catalysts were characterised by N₂-adsorption, H₂-adsorption, O₂–TPD and H₂–TPR.     

Stability of palladium-based catalysts during catalytic combustion of methane: The influence of water

The stability of methane conversion was studied over a Pd/Al₂O₃ catalyst and bimetallic Pd–Pt/Al₂O₃ catalysts. The activity of methane combustion over Pd/Al₂O₃ gradually decreased with time, whereas the methane conversion over bimetallic Pd–Pt catalysts was significantly more stable. The differences in combustion behavior were further investigated by activity tests where additional water vapor was periodically added to the feed stream. From these tests it was concluded that water speeds up the degradation process of the Pd/Al₂O₃ catalyst, whereas the catalyst containing Pt was not affected to the same extent. DRIFTS studies in a mixture of oxygen and methane revealed that both catalysts produce surface hydroxyls during combustion, although the steady state concentration on the pure Pd catalyst is higher for a fixed temperature and water partial pressure. The structure of the bimetallic catalyst grains with a PdO domain and a Pd–Pt alloy domain may be the reason for the higher stability, as the PdO domain appears to be more affected by the water generated in the combustion reaction than the alloy. Not all fuels that produce water during combustion will have stability issues. It appears that less strong binding in the fuel molecule will compensate for the degradation.     

The role of zeolite type on the lean NOx reduction by methane over Pd loaded pentasil zeolites

The lean selective catalytic reduction of NO_x by methane over protonic palladium loaded ZSM-5, FER and MOR, as well as, on bimetallic Pd–Pt-HMOR was examined. Special emphasis was paid on the combined effects of water and SO₂ in the feed stream. Under dry conditions and in the absence of SO₂, the degree of NO_x conversion at 450°C decreases as follows: Pd-HZSM-5>Pd-HMOR>Pd-HFER. Sulfur dioxide alone has no apparent effect on the activity for NO_x reduction, but the coexistence of water and SO₂ inhibits both NO_x and methane conversions. The extent of inhibition by water and SO₂ on NO_x reduction is Pd-HFER>Pd-HZSM-5>Pd-HMOR. Acid mordenite doped with low levels of Pt and Pd leads to an active catalyst that is more tolerant to the presence of either water or SO₂ than the corresponding monometallic Pt- and Pd-HMOR. Nevertheless, NO_x reduction is also inhibited at temperatures below 450°C when SO₂ and water are both present. TPD experiments of water over calcined samples of protonic Pd supported pentasil zeolites, Pd/γ-Al₂O₃ and Pt–Pd-HMOR with and without pretreatment in SO₂+O₂ indicate that sulfation of the surface increases water chemisorption by the support. Therefore, the observed decrease of NO_x reduction on Pd-loaded zeolite catalysts when SO₂ and H₂O coexist in the feed stream may be due to enhanced water inhibition and presumably active site poisoning.     

Kinetics of PdO combustion catalysis

The kinetics of the catalytic combustion of methane by supported palladium oxide catalysts (2 wt.-% Pd/La₂O₃·11A1₂O₃ and 5 wt.-%Pd/ γ-A1₂0₃ were examined for several oxygen partial pressure levels over the temperature range from 40–900°C using temperature-programmed reaction and slow ramp and hold temperature-time transient techniques. Combustion rates were measured by differential reaction in a fixed bed of powdered catalyst at lower temperatures (200–500°C). Also, by preparing the catalysts as thin (ca. 10 μm) coatings on an alumina tube and conducting the experiments with very high flows of dilute methane and oxygen in helium, the rate measurements were extended up to 900°C without significant contribution from gas phase reactions. The specific combustion activity of supported PdO shows a persistent hysteresis between 450 and 750°C, i.e., the rate of combustion between these temperature limits depends strongly on whether the catalyst is cooling from above 750°C or heating from below 450°C. This region is also notable for negative apparent activation energy in the rate of methane oxidation, i.e., the rate increases with decreasing temperature during reoxidation of the Pd metal and decreases with increasing temperature (especially with low oxygen partial pressure) prior to decomposition of the bulk oxide. Detailed time-temperature transient kinetic analyses were performed for supported PdO catalysts within the 450–750°C temperature range. The hysteresis in methane combustion rate is caused by a higher activation energy for reduction of oxygen chemisorbed on metallic Pd and by suppressed reoxidation of Pd metal relative to PdO decomposition.     

Catalytic combustion concept for gas turbines

Catalytic combustion for gas turbines was investigated, based on a partial catalytic combustion section followed by a homogeneous combustion zone. A pressurized test rig (<25 bar) was built to test the influence of various parameters on this concept using Pd and Pt catalysts.

The pressure influence on the apparent catalytic reaction rate was of the order 0.4, assuming that the reaction kinetics could be described by a power rate function which was of first order with respect to methane. Pd catalysts showed a pressure-dependent temperature for the transition of the active PdO to the much less active Pd. Combining Pd and Pt within one catalyst resulted in a considerably lower transition temperature.

Homogeneous combustion reactions set on from 650°C, depending on the methane concentration, pressure and flow. With inlet temperatures above 800°C the homogeneous combustion always started. At outlet temperatures below 1050°C high CO concentrations could be measured. At higher temperatures the CO, CH₄ and NO_x concentrations were lower than 5 ppm. During several experiments total conversion of CH₄ and CO was observed.     

Potassium–copper and potassium–cobalt catalysts supported on alumina for simultaneous NOx and soot removal from simulated diesel engine exhaust

This paper deals with the activity of bimetallic potassium–copper and potassium–cobalt catalysts supported on alumina for the reduction of NO_x with soot from simulated diesel engine exhaust. The effect of the reaction temperature, the soot/catalyst mass ratio and the presence of C₃H₆ has been studied. In addition, the behavior of two monometallic catalysts supported on zeolite beta (Co/beta and Cu/beta), previously used for NO_x reduction with C₃H₆, as well as a highly active HC-SCR catalyst (Pt/beta) has been tested for comparison. The preliminary results obtained in the absence of C₃H₆ indicate that, at temperatures between 250 and 400 °C, the use of bimetallic potassium catalysts notably increases the rate of NO_x reduction with soot evolving N₂ and CO₂ as main reaction products. At higher temperatures, the catalysts mainly favor the direct soot combustion with oxygen. In the presence of C₃H₆, an increase in the activity for NO_x reduction has been observed for the catalyst with the highest metal content. At 450 °C, the copper-based catalysts (Cu/beta and KCu2/Al₂O₃) show the highest activity for both NO_x reduction (to N₂ and CO₂) and soot consumption. The Pt/beta catalyst does not combine, at any temperature, a high NO_x reduction with a high soot consumption rate.     

Effect of solvo-thermal treatment temperature on the properties of sol–gel ZrO2–TiO2 mixed oxides as HDS catalyst supports

ZrO₂–TiO₂ mixed oxide (30–70 mol/mol) was prepared by low-temperature sol–gel followed by solvo-thermal treatment (1 day) at various temperatures (40, 80, 120, 160 and 200 °C). Selected samples of the corresponding single oxides were also prepared. Materials characterization was carried out by N₂ physisorption, XRD, thermal analysis (TG-DTA) and UV–vis DRS, infra-red and Laser-Raman spectroscopies. Binary solids of enhanced pore volume and pore size diameter were obtained by increasing the post-treatment severity. Anatase TiO₂ micro-segregation was evidenced by Raman spectroscopy for the mixed oxide solvo-treated at the highest temperature. This solid also showed the highest crystallization temperature to ZrTiO₄ (702 °C). Mo impregnated (2.8 atom nm⁻²) on various mixed oxides was sulfided under H₂S/H₂ (400 °C, 1 h), the catalysts being tested in the dibenzothiophene hydrodesulfurization (HDS, T = 320 °C, P = 5.59 MPa). By increasing the severity of the solvo-treatment improved supports for MoS₂ phase were obtained. The HDS activity of the catalyst with carrier post-treated at 200 °C was 40% higher (in per total mass basis) than that of sulfided Mo supported on the binary oxide solvo-treated at 80 °C. The ZrO₂–TiO₂-supported catalysts showed higher selectivity to products from the hydrogenation route than their counterparts supported on either single oxide.     

Catalytic combustion of methane over palladium exchanged zeolites

Palladium cation exchanged zeolites (ZSM-5, mordenite and ferrierite) were studied as catalysts for methane combustion. Pd-zeolites showed much higher activities than PdO/Al₂O₃. For comparable palladium loadings, PdO/Al₂O₃ requires a reaction temperature of ca. 70–80°C higher than Pd-ZSM-5 for conversions between 50–100%. The catalytic activity of Pd-ZSM-5 seems to be related to its reducibility. Temperature-programmed reduction experiments with carbon monoxide showed a lower reduction temperature (ca. 157°C) for Pd-ZSM-5 than for PdO/Al₂O₃ (225°C). Further, the positioning of the palladium by ion exchange offers a highly dispersed form of Pd^II supported on the high surface area zeolite.     

Catalytic combustion over platinum group catalysts: fuel-lean versus fuel-rich operation

Performance data are presented for methane oxidation on alumina-supported Pd, Pt, and Rh catalysts under both fuel-rich and fuel-lean conditions. Catalyst activity was measured in a micro-scale isothermal reactor at temperatures between 300 and 800 °C. Non-isothermal (near adiabatic) temperature and reaction data were obtained in a full-length (non-differential) sub-scale reactor operating at high pressure (0.9 MPa) and constant inlet temperature, simulating actual reactor operation in catalytic combustion applications.

Under fuel-lean conditions, Pd catalyst was the most active, although deactivation occurred above 650 °C, with reactivation upon cooling. Rh catalyst also deactivated above 750 °C, but did not reactivate. Pt catalyst was active above 600 °C. Fuel-lean reaction products were CO₂ and H₂O for all three catalysts.

The same catalysts tested under fuel-rich conditions demonstrated much higher activity. In addition, a ‘lightoff’ temperature was found (between 450 and 600 °C), where a stepwise increase in reaction rate was observed. Following ‘lightoff’ partial oxidation products (CO, H₂) appeared in the mixture, and their concentration increased with increasing temperature. All three catalysts exhibited this behavior.

High-pressure (0.9 MPa) sub-scale reactor and combustor data are shown, demonstrating the benefits of fuel-rich operation over the catalyst for ultra-low emissions combustion.     

Non-steady activity during methane combustion over Pd/Al2O3 and the influences of Pt and CeO2 additives

Methane combustion over Pd/Al₂O₃ catalysts with and without added Pt and CeO₂ in both oxygen-rich and methane-rich mixtures at temperatures in the range 250–520°C has been investigated using a temperature-programmed reaction procedure with on-line gas analysis (FTIR). During the temperature loop under oxygen-rich conditions, there was an appreciable hysteresis in the activity of unmodified Pd/Al₂O₃, which was greatly enhanced over Pd–Pt/Al₂O₃. Over both catalysts the hysteresis was reversed under slightly methane-rich atmospheres, and as temperature was reduced, a sudden collapse or fluctuations in activity were shown respectively over Pd–Pt/Al₂O₃ and Pd/Al₂O₃. Such non-steady behaviour was almost eliminated over Pd/Al₂O₃–CeO₂. Under a very narrow range of conditions and over a Pd/Al₂O₃ packed bed, oscillation of methane combustion was observed.     

Catalytic performance of Co3O4/CeO2 and Co3O4/CeO2–ZrO2 composite oxides for methane combustion: Influence of catalyst pretreatment temperature and oxygen concentration in the reaction mixture

The influence of catalyst pre-treatment temperature (650 and 750 °C) and oxygen concentration (λ = 8 and 1) on the light-off temperature of methane combustion has been investigated over two composite oxides, Co₃O₄/CeO₂ and Co₃O₄/CeO₂–ZrO₂ containing 30 wt.% of Co₃O₄. The catalytic materials prepared by the co-precipitation method were calcined at 650 °C for 5 h (fresh samples); a portion of them was further treated at 750 °C for 7 h, in a furnace in static air (aged samples).

Tests of methane combustion were carried out on fresh and aged catalysts at two different WHSV values (12 000 and 60 000 mL g⁻¹ h⁻¹). The catalytic performance of Co₃O₄/CeO₂ and Co₃O₄/CeO₂–ZrO₂ were compared with those of two pure Co₃O₄ oxides, a sample obtained by the precipitation method and a commercial reference. Characterization studies by X-ray diffraction (XRD), BET and temperature-programmed reduction (TPR) show that the catalytic activity is related to the dispersion of crystalline phases, Co₃O₄/CeO₂ and Co₃O₄/CeO₂–ZrO₂ as well as to their reducibility. Particular attention was paid to the thermal stability of the Co₃O₄ phase in the temperature range of 750–800 °C, in both static (in a furnace) and dynamic conditions (continuous flow). The results indicate that the thermal stability of the phase Co₃O₄ heated up to 800 °C depends on the size of the cobalt oxide crystallites (fresh or aged samples) and on the oxygen content (excess λ = 8, stoichiometric λ = 1) in the reaction mixture. A stabilizing effect due to the presence of ceria or ceria–zirconia against Co₃O₄ decomposition into CoO was observed.

Moreover, the role of ceria and ceria–zirconia is to maintain a good combustion activity of the cobalt composite oxides by dispersing the active phase Co₃O₄ and by promoting the reduction at low temperature.     

Effect of copper species and the presence of reaction products on the activity of methane oxidation on supported CuO catalysts

The activity of the various CuO species found in supported copper catalysts and the effect of the presence of reaction products, CO₂ and H₂O, was studied during the complete oxidation of methane. Series of copper catalysts supported on ZrO₂, Al₂O₃ and SiO₂ with different metal concentrations were analyzed under identical experimental conditions of reactant concentration and temperature. The catalysts were characterized by TPR, UV–vis spectroscopy and XRD. The results show that the activity of supported CuO is closely related to the kind of Cu species formed on the different supports. It was found that the Cu species formed on ZrO₂ and Al₂O₃ are dependent on the metal loading/support's surface area ratio, and that the activity of highly dispersed Cu is substantially higher than that of bulk CuO. In the case of silica, only the formation of bulk CuO was detected, accounting for the low activity of CuO/SiO₂ catalysts. The activity of highly dispersed Cu species formed on ZrO₂ is higher than those formed over Al₂O₃, and it is not significantly affected by the formation of bulk CuO on the surface. On the contrary, the activity of copper species formed on alumina decreases continuously as the Cu loading is increased. Thus, for the range of copper loading studied in this work, the activity of the catalysts, per gram of loaded Cu, follows the sequence: CuO/ZrO₂ > CuO/Al₂O₃  CuO/SiO₂. It was also found that CO₂ does not inhibits the activity of the CuO/ZrO₂ catalysts, while water inhibits the combustion reaction of methane, with an estimated reaction order of about −0.2 for temperatures between 360 °C and 420 °C.     

Efficient photocatalysts by hydrothermal treatment of TiO2

The aim of this work was to identify the optimum synthesis conditions and the most effective technique for noble metal deposition in a perovskite/palladium-based catalyst for natural gas combustion. The solution combustion synthesis (SCS) of perovskite/zirconia-based materials was investigated, by starting from metal nitrates/glycine mixtures. Characterization and catalytic activity tests were performed on as-prepared powders and then repeated after calcination for 2 h at 900 °C in calm air. Calcination appeared to be beneficial in that, despite lowering the specific surface area, it promoted the simultaneous crystallization of both LaMnO₃ and ZrO₂ and the half-conversion temperature (T₅₀), regarded as an index of catalytic activity, was lowered. Two phases, both active towards methane oxidation – lanthanum manganate and palladium oxide – were combined so as to evaluate their synergism in terms of catalytic activity. Pd was therefore added either via incipient wetness impregnation on LaMnO₃·2ZrO₂ or through a one-step SCS-based route. Characterization and catalytic activity tests followed suit. Optimal composition and preparation routes were found: T₅₀ was lowered from 507 °C – pure LaMnO₃ prepared via SCS – to 432 °C attained with a 2% (w/w) Pd load on pre-calcined LaMnO₃·2ZrO₂.     

Complete and partial catalytic oxidation of methane over substrates with enhanced transport properties

The development of improved substrate properties for catalytic combustion has been an area of much interest in recent years. Towards this end, Precision Combustion Inc. has developed novel short channel length, high cell density substrates (trademarked Microlith^®) and high surface area ceramic coatings for them. These substrates avoid substantial boundary layer buildup and greatly enhance heat and mass transfer rates in reactors. The high cell density of these substrates results in high amount of the catalyst per unit of reactor volume. In this paper we examine the performance of these substrates coated with precious metal catalysts for the catalytic combustion and reforming of methane.

Under fuel-lean operating conditions the surface temperature of Pd-based catalyst supported on Microlith^® substrate and the temperature of the gas exiting the reactor remain stable at 800 °C over a wide range of inlet conditions. This is attributed to combination of enhanced transport properties and characteristics of Pd–PdO transformation. Preheating of the gas mixture in the Microlith^® reactor was sufficient to stabilize a downstream premixed flame with NO_x, CO, and UHC emissions in the single digit ppm range.

Microlith^® substrates were also examined for partial oxidation of methane under fuel-rich conditions. The enhanced transport properties of the Microlith^® substrate allowed complete conversion of methane with surface temperature not exceeding material limits at 93% selectivity to partial oxidation products. High flow rate of reactants result in extremely high power densities and syngas output. The catalyst performance was observed to be stable over 500 h of operation.     

Effect of synthetic reducing agents on morphology and ORR activity of carbon-supported nano-Pd–Co alloy electrocatalysts

Three different reducing agents, ethylene glycol (EG), formaldehyde (HCHO), and sodium borohydrate (NaBH₄), were used in the synthesis of carbon-supported Pd–Co catalysts (Pd–Co/C–EG, Pd–Co/C–HCHO, and Pd–Co/C–NaBH₄, respectively). The differences among these three catalysts in morphology and electrocatalytic activity for oxygen reduction reaction (ORR) were observed and characterized using X-ray diffraction, energy dispersive X-ray analysis, transmission electron microscope, Fourier transform infrared spectra, surface cyclic voltametry, and rotating disk electrode technique. It was observed that by using a mild reducing agent such as EG, well-controlled and homogenous nucleation and growth could be achieved during the catalyst synthesis. With respect to the morphology and ORR activity of synthesized catalysts, the order of preferred reducing agents was found to be EG > NaBH₄ > HCHO. In order to improve activity and stability, the catalysts were heat-treated at temperatures ranging from 300 °C to 700 °C. It was found that for all three Pd–Co/C catalysts, a temperature of 300 °C gave the best catalyst morphology and ORR activity. The investigation in ORR kinetics catalyzed by these three catalysts revealed that all three could catalyze a four-electron reduction of oxygen to produce water. The average Tafel slope of the catalyzed ORR was found to be 70 mV/dec, suggesting that the determining step in the mechanism is a one-electron transfer process. In an effort to validate the theoretical explanation, the ORR activity as a function of particle size, Pd lattice constant, and Pd–Pd bond distance of the three Pd–Co/C catalysts was also investigated. In addition, in the case of EG as reducing agent the impregnation–reduction method employed in this work was simplified, because the need for a stabilizing agent usage was removed and water was used as the solvent.     

Abatement of volatile organic compounds: oxidation of ethanal over niobium oxide-supported palladium-based catalysts

Niobium-supported palladium-based catalysts (Pd, Pd–Cu and Pd–Au) were employed in the oxidation of ethanal. The catalysts were prepared according to original methods by either multi-steps (anchoring of complexes, calcination and reduction) or one-step (photoassisted reduction) procedures. The oxidation of ethanal was carried out in gas phase in a dynamic-differential reactor at 300 °C at atmospheric pressure. The activity/selectivity of the catalysts depend on (i) the catalyst preparation; (ii) the presence of a second metal. Addition of Au or Cu decreases the catalysts deactivation and the best performance in total oxidation was obtained with Pd–Au/Nb₂O₅ prepared by photoassisted reduction. As shown by in situ IR spectroscopy of adsorbed CO, this peculiarity may be ascribed to Au→Pd electron donation, which prevents the surface oxidation of palladium particles.     

In situ XAFS analysis of Pd–Pt catalysts during hydrotreatment of model oil

Supported Pd–Pt catalysts are efficient for hydrodesulfurization (HDS) and hydrodearomatization (HDA) reactions of diesel fuel and their activity varied with the kinds of supports. Concerning HDA, alumina supported catalysts showed four times higher TOF (turn over frequency) than silica supported one. In order to elucidate the difference in activity, the structural analysis of the active phase was performed. After reduction pretreatment, relatively uniform and large metallic alloy Pd–Pt particles were formed on SiO₂, whereas, Pd and Pt atoms formed rather segregated particles on Al₂O₃. Subsequent X-ray absorption of fine structure (XAFS) analysis under HDS conditions showed no contribution of sulfur for SiO₂ supported catalyst, whereas, formation of sulfided metal species was observed in XAFS spectra for the Al₂O₃ supported catalyst. It is suggested that on Pd–Pt/SiO₂, thin sulfide layer on the metal cluster surface blocked the active sites and lowered the HDA activity. Presence of partially sulfided phase originated from rather segregated structure like Pd–Pt/Al₂O₃ is thought to be requisite for high HDA activity.     

Investigation of bio-ethanol steam reforming over cobalt-based catalysts

The catalytic performance of cobalt catalysts supported on γ-Al₂O₃, TiO₂, ZrO₂ were studied for bio-ethanol steam reforming (BESR) reaction. The supported catalysts (10 wt%Co) were prepared by impregnation and characterized through Thermogravimetric analysis (TGA), H₂ chemisorption, laser Raman Spectroscopy, Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS), and temperature-programmed reaction (TPRxn). The metallic cobalt sites were found to correlate with the BESR reaction activity. The reaction and H₂ chemisorption showed that ZrO₂ supported catalyst showed the best dispersion and best catalytic activity. Over the 10% Co/ZrO₂ catalyst, using a H₂O:EtOH:inert molar ratio of 10:1:75 and a GHSV = 5000 h⁻¹, 100% ethanol conversion and a yield of 5.5 mol H₂/mol EtOH were obtained at 550 °C and atmospheric pressure.