Swelling behavior of poly(n‐butyl acrylate/1,6‐hexane‐diol‐di‐acrylate)/nematic liquid crystal E7 systems: Experimental measurements and modeling by factorial design method

The swelling process of poly(n‐butyl acrylate/1,6‐hexane‐diol‐di‐acrylate) [Poly(Abu/HDDA)] networks, immersed in a liquid crystalline (LC) solvent, was investigated in order to obtain improved swelling ratio values upon application of an original method using a central composite design. The polymer/LC systems under investigation were elaborated via a photopolymerization/crosslinking phase separation process induced by UV radiation of initial mixtures composed of mono‐ and bifunctional monomers, a photoinitiator, and the low‐molar‐weight nematic LC blend E7. The parameters which strongly impact the swelling behavior of Poly(Abu/HDDA)/E7 systems were identified as temperature and concentration of the bifunctional monomer in the initial photopolymerizable mixture, thus controlling the crosslinking density of the final polymer network. The existence of interactions and synergies between these two parameters were also examined. The quality of the model was verified by a good agreement between experimental results and predicted response. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45230.     

Thermoreversible gelation of a polystyrene–poly(ethylene/butylene)–polystyrene triblock copolymer in n‐octane/4‐methyl‐2‐pentanone solutions

The thermoreversible gelation of a triblock copolymer polystyrene‐block‐poly(ethylene/butylene)‐block‐polystyrene in n‐octane and two solvent mixtures of n‐octane and 4‐methyl‐2‐pentanone with a high n‐octane content has been studied. n‐Octane and 4‐methyl‐2‐pentanone are selective solvents for the middle poly(ethylene/butylene) block and the end polystyrene blocks, respectively. The influence of the solvent composition on the sol–gel transition and the mechanical properties of the gels was studied. The gel formation temperature increased with the copolymer concentration and the n‐octane content in the solvent system. The mechanical properties of the different gels were studied through oscillatory shear measurements. The concentration dependence of the elastic storage modulus showed an exponent close to that expected for gels in good solvents (2.25) that possess a structure similar to those of chemical networks. © 2002 Society of Chemical Industry     

Electrospinning of solvent‐resistant nanofibers based on poly(acrylonitrile‐co‐glycidyl methacrylate)

This article reports on the preparation of novel solvent‐resistant nanofibers by electrospinning of poly(acrylonitrile‐co‐glycidyl methacrylate) (PANGMA) and subsequent chemical crosslinking. PANGMA nanofibers with diameters ranging from 200 to 600 nm were generated by electrospinning different solutions of PANGMA dissolved in N,N‐dimethylformamide. Different additives were added to reduce the fiber diameter and improve the morphology of the nanofibers. The as‐spun PANGMA nanofibers were crosslinked with 27 wt % aqueous ammonia solution at 50°C for 3 h to gain the solvent resistance. Swelling tests indicated that the crosslinked nanofibers swelled in several solvents but were not dissolved. The weight loss of all the crosslinked nanofibrous mats immersed in solvents for more than 72 h was very low. The characterization by electron microscopy revealed that the nanofibrous mats maintained their structure. This was also confirmed by the results of the pore size measurements. These novel nanofibers are considered to have a great potential as supports for the immobilization of homogeneous catalysts and enzymes. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Swelling of crosslinked polyacrylates in isotropic and anisotropic solvents

The purpose of this study was to examine the swelling and deswelling of photochemically crosslinked poly(n‐butylacrylate) networks in isotropic and anisotropic solvents. The phase diagrams were established in terms of composition and temperature for five isotropic solvents, acetone, cyclohexane, methanol, tetrahydrofuran, and toluene, and two low‐molecular‐weight nematic liquid crystals, 4‐cyano‐4′‐n‐pentyl‐biphenyl and an eutectic mixture of cyanoparaphenylenes. Networks were formed by ultraviolet curing in the presence of 0.5 wt % difunctional monomer (hexane diol‐di‐acrylate) and 0.5 wt % photoinitiator (Darocur 1173). Immersion in excess solvent allowed us to measure the solvent uptake by weight and to determine the size increase by optical microscopy in terms of temperature. We calculated weight and diameter ratios considering the swollen‐to‐dry network states of the samples. Phase diagrams were analyzed with the phantom network model according to the Flory–Rehner theory of rubber elasticity, and for the anisotropic solvents, modeling was supplemented with the Maier–Saupe theory of nematic order for free energy. The polymer–solvent interaction parameter was deduced as a function of temperature, but the values were in discrepancy with Fedors's model of solubility parameters, which overestimated the interaction. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1–9, 2004     

Crosslinking of poly(vinyl alcohol) and poly(vinyl acetate) using poly(maleic anhydride‐alt−2,4‐dimethyl‐1,3‐pentadiene) as polyfunctional crosslinker and decrosslinking by ozone degradation

Crosslinking and decrosslinking reactions of poly(vinyl alcohol) (PVA) and poly(vinyl acetate) (PVAc) using an alternating copolymer of maleic anhydride and 2,4‐dimethyl‐1,3‐pentadiene (PMAD) as the polyfunctional crosslinker and subsequent ozone degradation are reported. PVA and PVAc are heated at 200 °C for 0.5 to 3 h in the presence of 5 to 30 wt % of PMAD in the solid state to obtain the corresponding crosslinked polymers. The reactions of a hydroxy group of PVA and an acetate group of PVAc with an anhydride group of PMAD slowly proceed to give insoluble polymers with a loose crosslinking structure. Almost no change in the thermal decomposition temperatures and the IR spectra is observed during the crosslinking reactions. The crosslinked PVA produces hydrogels with a high swelling ratio of 500 to 1700%, which are readily degradable during a reaction with ozone in water at 0 °C. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44229.     

Partial crosslinking method for poly(2,6‐dimethyl‐1,4‐phenylene oxide)–poly(vinyl alcohol) membranes to obtain optimized stability and permeability

A partial crosslinking method was developed to modify hydrophilic membranes. The membrane was sandwiched between two porous plates to protect part of the areas, then immersed into a crosslinking solution such as glutaraldehyde, and finally, set free from the plates. The protected and unprotected areas were alternatively distributed to form a heterogeneous membrane. The unprotected areas were crosslinked to enhance the membrane stability, whereas the protected areas retained their original permeability. Three types of hydrophilic base membranes were selected and prepared from poly(2,6‐dimethyl‐1,4‐phenylene oxide) and poly(vinyl alcohol). The base membranes were partially crosslinked (5.56% of the direct area with enlarged areas) to investigate their stability and diffusion dialysis (DD) performances. The partially crosslinked membranes had remarkably reduced water uptake and swelling degrees compared with the base membranes (72.4–250.4 vs 178.2%–544.4% and 94.0%–408.0% vs. 163.8%–814.8%). Meanwhile, the membranes still retained high DD performances for separating HCl–FeCl₂ or NaOH–NaAlO₂ solutions. The dialysis coefficients of HCl and NaOH were much higher than those of the fully crosslinked membranes (0.0209 vs. 0.0109 m/h and 0.0059–0.0085 vs. 0.0017–0.0022 m/h). Hence, partial crosslinking was effective in optimizing the membrane hydrophilicity and permeability. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45305.     

Synthesis and characterization of pH‐sensitive networks containing degradable poly(1,3‐dioxolane) segments

pH‐sensitive networks were obtained by radical copolymerization of telechelic poly(1,3‐dioxolane) (PDXLDA) with acrylic acid (AA). PDXLDA was synthesized by acrylation of the corresponding dihydroxylated polyacetal (polyDXL) with AA in pyridine. The copolymer networks of poly(AA‐b‐DXL) showed pH sensitivity due to —COOH groups, which are insoluble in any solvents, but can swell in water or good solvents. The swelling behavior is closely related to the solvents and is composition‐dependent. The networks containing polyDXL segments can be decrosslinked under acidic conditions due to the low ceiling temperature of polyDXL. After degradation, the linear segments of polyDXL became cycled molecules. The networks' structure, swelling behavior, and degradation were characterized by Fourier transform infrared spectroscopy, differential scanning calorimetry, GC–MS analysis, and swelling data. This kind of material can be potentially used in biosystems, such as in intelligent drug‐delivery systems. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1678–1682, 2002     

Semi‐interpenetrating networks based on poly(N‐isopropyl acrylamide) and poly(N‐vinylpyrrolidone)

Three series of novel semi‐interpenetrating polymer networks, based on crosslinked poly(N‐isopropylacrylamide), PNIPA, and different amounts of the linear poly(N‐vinylpyrrolidone), PVP, were synthesized to improve the mechanical properties and thermal response of PNIPA gels. The effect of the incorporation of the linear PVP into the temperature responsive networks on the temperature‐induced transition, swelling/deswelling behavior, and mechanical properties was studied. Polymer networks with four different crosslinking densities were prepared with varying molar ratios (25/1 to 100/1) of the monomer (N‐isopropylacrylamide) to the crosslinker (N,N′‐methylenebisacrylamide). The hydrogels were characterized by determination of the equilibrium degree of swelling, the dynamic shear modulus and the effective crosslinking density, as well as tensile strength and elongation at break. Furthermore, the deswelling kinetics of the hydrogels was studied by measuring their water retention capacity. The inclusion of the linear hydrophilic PVP in the PNIPA networks increased the equilibrium degree of swelling. The tensile strength of the semi‐interpenetrating networks (SIPNs) reinforced with linear PVP was higher than that of the PNIPA networks. The elongation at break of these SIPNs varied between 22% and 55%, which are 22 – 41% larger than those for pure PNIPA networks. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Novel method to prepare charged mosaic membrane by using dipole‐like microspheres. I. Preparation and characterization of poly(4‐vinylpyridine/n‐butyl acrylate) seed latex with high solid content by soap‐free emulsion polymerization

The stable latex of poly(4‐vinylpyridine‐co‐n‐butyl acrylate) (P4VP/nBA) with a solid content as high as 10 wt % was prepared by a modified soap‐free emulsion polymerization. A mixture of water and organic solvents was employed as the continuous phase for increasing the solid content of the latex. Several organic solvents were investigated and, among them, ethyl acetate (EA) and diethyl ether (DE) were effective. The stable latex with 10 wt % solid content was prepared by charging 10 wt % EA or a EA/DE mixture (5 wt % each); however, more than 10 wt % solid content of the stable latex could not be obtained even by charging more than 10 wt % EA or a EA/DE mixture. The stable latex with 10 wt % solid content, which was crosslinked with less than 0.5 wt % (based on monomer) of ethylene glycol dimethacrylate, was prepared by charging 10 wt % of EA. In this case, however, the pH of the continuous phase had to be adjusted to lower than 4. The effects of EA on the characteristics of the resulting uncrosslinked latex were investigated by employing ζ‐potential measurements and scanning electron microscopy. It was found that the mass of coagulum decreased as the EA increased. At 8 wt % of EA, a stable latex of 10 wt % solid content without any coagulum was obtained. The ζ potential of particles increased from −100 up to 45.7 mV as the EA increased from 0 to 10 wt %. The effects of batch and semicontinuous copolymerization on the morphology of the microspheres were investigated by using DSC and ultrathin cross‐sectional transmission electron miscroscopy photos. A core–shell structure was not found, despite the batch copolymerization of 4VP(1)/nBA(2) (r₁ = 4.3, r₂ = 0.23), even with disparate reactivity ratios. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1731–1740, 2000     

Poly(ethylene glycol)‐containing cationic hydrogels with lipophilic character

Not much effort has been focused towards the development of hydrogels that swell in nonpolar solvents. We have synthesized a new set of polyelectrolyte hydrogels and demonstrated their ability to absorb a less‐polar or nonpolar organic solvent, as well as their ability to resist gel‐collapse in a predominantly nonpolar medium. The hydrogels were prepared by free radical polymerization of different molar ratios of poly(ethylene glycol) methyl ether acrylate and (3‐(methacryloylamino)propyl)‐trimethyl ammonium chloride as comonomers in an aqueous medium. Their swelling behavior in organic solvents was studied by varying the dielectric constant of the swelling medium including mixed‐solvent systems. Besides a high degree of swelling (up to 200 times) in polar solvents, some of the hydrogels also exhibited moderate swelling (up to 15 times) in less‐polar organic solvents. Hydrogels samples with high cationic content showed drastic change in swelling extent in some of the mixed‐solvent systems. It was also interesting to note that the retention of significant swelling in dimethyl sulphoxide–toluene mixture with even 90% toluene content for some compositions. These polyelectrolyte hydrogels with improved lipophilicity opens up greater opportunities for the development of even superior soft materials through proper structural optimizations that would successfully function for a wider range of solvents. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39873.     

Calcium ion‐induced self‐healing pattern of chemically crosslinked poly(acrylic acid) hydrogels

Poly(acrylic acid) hydrogels crosslinked with N,N′‐methylenebisacrylamide were synthesized by free radical polymerization. Polymerization conditions had a significant influence over the gel content and swelling behaviour of the hydrogels. The incorporation of calcium ions led to the origin of a self‐healing feature. The self‐healing behaviour and mechanical performance of the hydrogels were systematically investigated. The hydrogels showed good tensile strength of 1 MPa and excellent stretchable behaviour where hydrogels regained instantaneously. Hydrogel pieces joined together to become an integrated matrix as soon as two cut pieces were brought in contact. The hydrogels possessed a marked healing efficiency of 97% within 6 h at room temperature without any external intervention. The results are explained in terms of the dynamic mobility of calcium ions within the dual‐crosslinked networks of the poly(acrylic acid) hydrogels. © 2017 Society of Chemical Industry     

Preparation and microstructural analysis of poly(ethylene oxide) comb‐type grafted poly(N‐isopropyl acrylamide) hydrogels crosslinked by poly(ϵ‐caprolactone)

Poly(N‐isopropyl acrylamide) (PNIPAAm)‐graft‐poly(ethylene oxide) (PEO) hydrogels crosslinked by poly(?‐caprolactone) diacrylate were prepared, and their microstructures were investigated. The swelling/deswelling kinetics and compression strength were measured. The relationship between the structure and properties of hydrogel are discussed. It was found that the PEO comb‐type grafted structure reduced the thermosensitivity and increased the compression strength. The addition of poly(?‐caprolactone) (PCL) accelerated the deswelling rate of the hydrogels. Meanwhile, the entanglement of PCL chains restrained the further swelling of the network of gels. The PCL crosslinking agent and PEO comb‐type grafted structure made the behavior of the hydrogels deviate from the rubber elasticity equations. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Analysis of the swelling dynamics of crosslinked P(N‐iPAAm‐co‐MAA) copolymers,the corresponding homopolymers and their interpenetrating networks. Kinetics of water penetration into the gel above the pKaof MAA comonomeric units

The effect of composition on the swelling kinetics of a series of crosslinked poly(N‐isopropylacrylamide)s [P(N‐iPAAm)] and poly(methacrylic acid)s [P(MAA)], their statistical copolymers P(N‐iPAAm‐co‐MAA), and some sequential interpenetrating networks (IPNs) has been studied at pHs above the pK_a of MAA comonomeric units. The swelling process of the hydrogels upon immersion in buffer solutions was monitored by the weight change as a function of time. First‐order kinetics apply better than second‐order kinetics which fail, especially for predicting swelling equilibrium values. However, hydrogels presenting hydrogen bonding between MAA and N‐iPAAm units do not obey either first‐order or second‐order kinetics. The high n values found indicate that the swelling process is mostly controlled by polymer relaxation. Copyright © 2003 Society of Chemical Industry     

Preparation of pH‐Sensitive Networks by Ultraviolet Induced Crosslinking of Poly(ethylene oxide)‐Poly(2‐vinylpyridine) Blends

Blends of poly(ethylene oxide) of molecular weight 1 000 000 and poly(2‐vinylpyridine) of molecular weight 300 000 were crosslinked by exposure to ultraviolet radiation at 25, 75 and 115°C in the presence of benzophenone as a hydrogen‐abstracting agent. The crosslinking efficiency as well as the pH sensitivity strongly depend on the blend composition, the concentration of benzophenone and the irradiation temperature. The equilibrium swelling behavior of the mixed networks in aqueous solution was studied as a function of pH at constant ionic strength. A more pronounced swelling transition upon pH changes from 2 to 7 is observed at greater content of P2VP in the networks. The addition of poly(propylene oxide) to the P2VP‐PEO networks leads to enhanced mechanical strength and to much greater swelling dependence on pH, due to the hydrophobic and elastic nature of PPO.     

Enantioselective esterification reaction using immobilized Candida rugosa lipase on poly(N‐vinyl‐2‐pyrrolidone‐co‐styrene) hydrogel

Lipase from Candida rugosa was immobilized on poly(N‐vinyl‐2‐pyrrolidone‐co‐styrene) hydrogel (poly‐(VP‐co‐ST)) with ethylene dimethacrylate and α,α'‐azoisobutyronitrile, which act as crosslinker and initiator, respectively. Three different compositions of monomers were used, namely VP(%):ST(%), 10:90, 50:50, and 70:30 (wt(%)/wt(%)). The immobilized lipases were used in the enantioselective esterification of (R,S)‐2‐(4‐chlorophenoxy)‐propanoic acid with n‐tetradecanol. The optimum reaction condition of the enantioselective esterification for the native lipase and the poly(VP‐co‐ST) hydrogel immobilized lipases was determined with respect to temperature, solvents, and initial water activity (a_w). The optimum temperature obtained was 40°C, with the poly(VP‐co‐ST) hydrogel immobilized lipase VP(%)/ST(%):10:90 showing the highest enantiomeric excess. In the solvent effect studies, the best solvents for high enantioselectivity were chloroform and carbon tetrachloride. In the a_w studies, optimum α_w for NL, VP(%):ST(%), 10:90, and 50:50 was 0.328, while for VP(%):ST(%), 70:30, it was 0.55. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3381–3386, 2004     

Solvent and pH resistance of surface crosslinked chitosan/poly(acrylonitrile) composite nanofiltration membranes

The resistance of novel surface crosslinked Chitosan/poly(acrylonitrile) (PAN) composite nanofiltration (NF) membranes to pH and organic solvents was studied with respect to the effects of crosslinking parameters, namely, glutaraldehyde concentration and crosslinking time. The pH resistance was determined by permeation of aqueous acidic (pH 2.5) and basic (pH 11) solutions as well as swelling studies in the pH range of 2.5–11. The solvent resistance was determined by swelling, immersion, and permeation studies with several industrially important organic solvents, namely methanol, ethanol, iso‐propanol, methyl ethyl ketone, ethyl acetate and hexane. It was observed that the crosslinked composite membranes maintain the permeate fluxes for test solvents for 2 h of continuous operation without any significant change in flux. SEM studies on membrane samples after immersion as well as permeation with the above‐mentioned solvents indicated that the membrane morphology was maintained. The results are explained in terms of solvent–membrane polar and hydrophobic interactions, using solubility parameters of membrane and solvents and dielectric constants of solvents. Pure water flux and polyethylene glycol transmission data indicated that at pH 2.5 and 11, the membrane stability increased with increasing glutaraldehyde concentration and was much better at pH 11 than at pH 2.5. All surface crosslinked membranes showed reduced swelling between pH 4–10. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1782–1793, 2000     

Delivery of bupivacaine included in poly(acrylamide‐co‐monomethyl itaconate) hydrogels as a function of the pH swelling medium

Copolymeric hydrogels of poly(acrylamide‐co‐monomethyl itaconate) (A/MMI) crosslinked with N,N′‐methylenbisacrylamide (NBA) were synthesized as devices for the controlled release of bupivacaine (Bp). Two compositions of the copolymer, 60A/40MMI and 75A/25MMI, were studied. A local anesthetic was included in the feed mixture of polymerization (2–8 mg Bp/tablet) and by immersion of the copolymeric tablets in an aqueous solution of the drug. A very large amount of Bp (36–38 mg Bp/tablet) was included in the gels by sorption due to interactions between the drug and the side groups of the hydrogels. Swelling and drug release were in accordance with the second Fick's law at the first stages of the processes. The swelling behavior of these copolymers depended on the pH of the medium. The equilibrium swelling degree (W_∞) was larger at pH 7.5 (W_∞ ≈ 90 wt %) than at pH 1.5 (W_∞ ≈ 52–64 wt %) due to the ionization of the side groups of the copolymer. Release of the drug also depended on the pH of the swelling medium; at pH 7.5, about 60% of the included drug was released, and at pH 1.5, about 80% was released. Bp release was controlled by the comonomer composition of the gels, their drug‐load, and the pH of the swelling medium. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 327–334, 2002     

Synthesis and swelling properties of pH‐ and temperature‐sensitive interpenetrating polymer networks composed of polyacrylamide and poly(γ‐glutamic acid)

Novel hydrogels of interpenetrating polymer networks (IPNs) composed of polyacrylamide and poly(γ‐glutamic acid) were synthesized. In these systems, both polymers were crosslinked independently; this reduced the potential loss of a polymer during the washing process, as often occurs in semi‐IPN systems. Interpolymer interactions were investigated with Fourier transform infrared spectroscopy and differential scanning calorimetry. These studies suggested possible interactions between both polymers by the formation of hydrogen bonds. The swelling behavior of these hydrogels was analyzed by immersion of the hydrogel samples in deionized water at 25 and 37°C and in buffer solutions with pHs of 3, 7, and 10. The kinetics of swelling showed increases in the values of the swelling ratio with increasing immersion time in the swelling medium, molar proportion of the biopolymer in the hydrogel, temperature, and pH of the swelling medium. All of the hydrogels swelled rapidly and reached equilibrium in an average time of 40 min. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Physicomechanical studies and solvent resistance analysis of melt‐blended novel ethylene‐1‐octene elastomer and ethylene‐co‐acrylic acid interpenetrating network hybrids

Polar modification of poly(ethylene‐co‐octene) (POE) elastomer was carried out with a relatively new approach. Poly(ethylene‐co‐acrylic acid) (EAA) was taken as the modifier and POE with a calculated amount of EAA were coextruded with dicumyl peroxide (DCP; used as a crosslinker). The majority of the compositions showed the existence of a crosslinked EAA phase inside POE, although increasing DCP concentrations and extrusion temperatures were possibly capable of crosslinking either of the phases, as observed with a model composition. All of the samples were soft and light in nature. The best composition was the one that contained 13.3 wt % EAA; that composition showed excellent surface polarity and superior mechanical properties. Detailed solvent swelling experiments also yielded the best results for that particular composition. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Optimization of engineering and solvent resistive behavior of high vinyl acetate content EVA‐modified poly(ethylene‐co‐1‐octene) interpenetrating network blends using taguchi orthogonal array

Process parameters of poly (ethylene‐co‐vinyl acetate) (EVA)‐modified poly (ethylene‐co‐1‐octene) (POE)‐interpenetrating, double network blend was designed through Taguchi L9 orthogonal array as a novel approach for complete optimization of engineering and solvent‐swelling properties. Influence of different factors like EVA and peroxide concentrations, blending temperature, and blending time on gel content, tensile modulus, tensile strength, ultimate elongation were statistically calculated. Results showed good correlation between mathematical and physical inferences. Stress relaxation, hysteresis and other physico‐mechanicals like total elongation, solvent‐swelling, etc., were interestingly depended upon the nature of dominantly crosslinked phase instead of net crosslinking of the network hybrids. Sorption, on the other hand, depended on the hydrophobic‐hydrophilic property of the surfaces. The series of data produced finally helped to select the best process parameters under which a particular POE‐EVA blend composition yielded most balanced physico‐mechanicals. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012