Thermal stability of end‐capped and linear sulfonated polyimides,sulfonated polystyrene,and Nafion 117

The thermal stability of end‐caped and linear sulfonated polyimides (SPIs), sulfonated polystyrene (SPS), and a sulfonated perfluorinated hydrocarbon, Nafion 117, and the corresponding triethylammonium sulfonate salts was investigated by dynamic and isothermal thermogravimetric analysis (TGA). Gas chromatographic‐mass spectrographic analysis (GC/MS) of the sulfonated polymers and the salts to determine the volatiles released from acid and salt groups over a temperature range 200–275 °C was also investigated. GC/MS analysis reveals that water and sulfur dioxide volatiles are released from the sulfonic acids and water, sulfur dioxide and triethyl amine are released from the sulfonate salts. Dynamic and isothermal TGA studies based on weight loss revealed that the SPIs exhibited superior thermal stability than SPS and Nafion 117 sulfonic acids. However, dynamic TGA curves to determine the onset decomposition temperature of the sulfonic acid group reveal that Nafion 117 and SPS sulfonic acids exhibited greater thermal stabilities than the SPIs. The mechanisms of sulfonic acid and triethylammonium sulfonate salt decompositions based on GC/MS, ¹³C‐NMR, and dynamic TGA curves are proposed. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45694.     

Synthesis and modification of aromatic polyesters with chloroacetyl 3,5‐dibromo‐p‐hydroxybenzoic acid

Aromatic copolyesters based on diphenylolpropane and 3,5‐dibromo‐p‐hydroxybenzoic acid (p‐HBA) were synthesized by an acceptor‐catalyzed polycondensation method. During the synthesis, equimolar mixtures of chloranhydrides of isophthalic and terephthalic acids were used. The effects of p‐HBA on the tensile and thermal properties of the polyesters were investigated. The breaking stress and modulus of elasticity increased with the amount of p‐HBA up to 10% in molar mass. A further increase in p‐HBA caused deterioration of the tensile properties. The elongation at break decreased at low p‐HBA contents (<5%). The addition of p‐HBA increased the molecular packing and the limiting oxygen index and improved the thermal behavior of the synthesized polyesters. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synergistic effect of α‐ZrP and graphene oxide nanofillers on the gas barrier properties of PVA films

Two types of 2D nanofillers, α‐zirconium phosphate (α‐ZrP) and graphene oxide (GO), were synthesized and incorporated into poly(vinyl alcohol) (PVA) with 1 wt % loading level at various α‐ZrP:GO (Z:G = 5:1, 2:1, 1:1, 1:2, and 1:5) ratios. The resulting nanocomposites were tested for barrier properties by casting films from solution. The structure and morphology of α‐ZrP and GO were characterized by Fourier‐transform infrared spectroscopy, atomic force microscope, scanning electron microscopy, transmission electron microscopy, and X‐ray diffraction, which demonstrated successful preparation of exfoliated α‐ZrP and GO. The physical characteristics of the nanocomposite films, including thermal, mechanical, and gas barrier properties were investigated. The results indicated that the tensile strength, Young's modulus, and elongation at break of the PVA nanocomposite films with Z:G hybrid nanofiller improved compared to neat PVA. The glass transition temperature, melting temperature, and crystallinity also increased. Consequently there appears to be a synergistic effect with these two types of nanofillers that formed a specific macro structure of a “wall.” This macrostructure resulted in excellent O₂ gas barrier properties with the PVA/Z:G‐5:1 nanocomposite films having the best performance. The of the PVA/Z:G‐5:1 nanocomposite decreased from 1.835 × 10^?16 to 0.587 × 10^?16 cm³ cm cm^?2 s^?1 Pa^?1 compared with neat PVA. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46455.     

Synthesis of guar‐gum‐stabilized nanosized silver clusters with γ radiation

Gamma ray induced synthesis of Ag clusters in the aqueous medium has been carried out using natural polysaccharide guar gum as a stabilizer. The results showed that guar gum is very effective in binding the Ag clusters and restricts their size in the nano region. The surface plasmon resonance band in the wavelength range of 410–425 nm of visible region has confirmed the formation of Ag clusters. The size of the clusters is governed by the concentration of both, i.e. precursor Ag⁺ and guar gum. The clusters were characterized by TEM and XRD, which shows that the size of clusters is in the range of 10–30 nm. The results have shown that silver clusters stabilized by guar gum are stable in acid media and alkaline media is not a desired media for the synthesis. From thermogravimetric analysis it has been demonstrated that incorporation of nano sized Ag clusters within guar gum improves the thermal properties of irradiated guar gum. To the best of our knowledge, the use of guar gum as a stabilizer in the gamma ray induced synthesis of Ag nano clusters is being reported first time in the literature. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Crystallinity evolution of soft segments during the synthesis of polyester‐based waterborne polyurethane

Polyester‐based waterborne polyurethane (WPU) dispersions having poly(ethylene glycol) adipate diol, isophorone diisocyanate, and hexamethylene diisocyanate as the main raw materials were synthesized by an acetone process. In each step of the synthesis process, the intermediate products were collected, and the crystallization morphologies and relative crystallinity (X) of the soft segments (SSs) in their films were investigated by means of polarizing optical microscopy, differential scanning calorimetry, and X‐ray diffraction. The fracture surfaces and thermostability of the intermediate films were also investigated by scanning electron microscopy (SEM) and TGA, respectively. The results show that the crystalline dimensions of the SSs decreased substantially during the synthesis process of WPU. X of the SSs decreased after the prepolymerization reaction and increased after the hydrophilic chain‐extending reaction, then decreased after emulsification, and finally increased after the secondary chain‐extending reaction. Moreover, The SEM photos indicate that with decreasing crystalline dimensions, the fracture mechanisms of the intermediate films varied gradually from brittle failure to ductile fracture. The thermostability of the intermediates obtained in each step of the synthesis process was in accordance with the variation tendency of the X of the SSs. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40270.     

High‐performance PDMS membranes for pervaporative removal of VOCs from water: The role of alkyl grafting

To improve the pervaporation performance of PDMS membrane, alkyl groups with different chain length were grafted into PDMS matrix. The prepared membranes were characterized by ATR‐IR, DSC, TGA, PALS, and tensile testing. The effects of alkyl grafting on pervaporation performance of PDMS membrane were investigated in separation of ethyl acetate/water mixture. Experimental results show that the separation factor of PDMS membrane is largely improved by alkyl grafting because of the enhanced preferential sorption of ethyl acetate, and this improvement depends on alkyl grafting ratio and alkyl chain length. The total flux of PDMS membrane reduces after alkyl grafting owing to the decreased free volume. When grafting ratio is above 6.9%, membrane grafted with shorter alkyl groups is preferred for pervaporation. The best pervaporation performance is achieved by 9% octyl grafted PDMS membranes with a separation factor of 592 and a total flux of 188 gm^?2 h^?1 in separation of 1% ethyl acetate/water mixture at 40 °C. Moreover, this octyl grafted PDMS membrane also exhibits excellent separation performance in removal of butyl acetate, methyl‐tert‐butyl ether, and n‐butanol from water. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43700.     

Radiation‐induced grafting of glycidyl methacrylate onto high‐density polyethylene (HDPE) and radiation lamination of HDPE

Radiation‐induced grafting of glycidyl meth‐acrylate (GMA) onto high‐density polyethylene (HDPE) and the radiation lamination of HDPE by bulk grafting of GMA were reported. The effects of irradiation dose, monomer concentration, and atmosphere on grafting were investigated. The extent of grafting initially increased with irradiation dose and then remained almost constant. The extent of grafting was higher in 2M GMA than in 1M GMA at the same irradiation dose. The extent of grafting in nitrogen was higher than that in air. The grafted samples were characterized with FTIR spectrometry and thermogravimetric (TG) analysis. A carbonyl group was found on grafted HDPE samples, and the carbonyl index increased with the extent of grafting. TG analyses proved the existence of grafted materials on HDPE and the grafted GMA thermally decomposes at a temperature lower than that of HDPE. Strong adhesion could be obtained with radiation lamination of HDPE by bulk grafting of GMA. Benzophenone facilitates the grafting in a proper concentration range. The adhesion mechanism of the laminated samples was the entanglement of the grafted chains. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 772–779, 2005     

Partial crosslinking method for poly(2,6‐dimethyl‐1,4‐phenylene oxide)–poly(vinyl alcohol) membranes to obtain optimized stability and permeability

A partial crosslinking method was developed to modify hydrophilic membranes. The membrane was sandwiched between two porous plates to protect part of the areas, then immersed into a crosslinking solution such as glutaraldehyde, and finally, set free from the plates. The protected and unprotected areas were alternatively distributed to form a heterogeneous membrane. The unprotected areas were crosslinked to enhance the membrane stability, whereas the protected areas retained their original permeability. Three types of hydrophilic base membranes were selected and prepared from poly(2,6‐dimethyl‐1,4‐phenylene oxide) and poly(vinyl alcohol). The base membranes were partially crosslinked (5.56% of the direct area with enlarged areas) to investigate their stability and diffusion dialysis (DD) performances. The partially crosslinked membranes had remarkably reduced water uptake and swelling degrees compared with the base membranes (72.4–250.4 vs 178.2%–544.4% and 94.0%–408.0% vs. 163.8%–814.8%). Meanwhile, the membranes still retained high DD performances for separating HCl–FeCl₂ or NaOH–NaAlO₂ solutions. The dialysis coefficients of HCl and NaOH were much higher than those of the fully crosslinked membranes (0.0209 vs. 0.0109 m/h and 0.0059–0.0085 vs. 0.0017–0.0022 m/h). Hence, partial crosslinking was effective in optimizing the membrane hydrophilicity and permeability. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45305.     

Co‐extruded polymeric films for gas separation membranes

In recent years, gas separation has become an important step in many production process streams and part of final products. Through the use of melt co‐extrusion and subsequent orientation methods, gas separation membranes were produced entirely without the use of solvents, upon which current methods are highly dependent. Symmetric three layer membranes were produced using poly(ether‐block‐amide) (PEBA) copolymers, which serve as a selective material that exhibits a high CO₂ permeability relative to O₂. Thin layers of PEBA are supported by a polypropylene (PP) layer that is made porous through the use of two methods: (1) inorganic fillers or (2) crystal phase transformation. Two membrane systems, PEBA/(PP + CaCO₃) and PEBA/β‐PP, maintained a high CO₂/O₂ selectivity while exhibiting reduced permeability. Incorporation of an annealing step either before or after orientation improves the membrane gas flux by 50 to 100%. The improvement in gas flux was a result of either elimination of strain induced crystallinity, which increases the selective layer permeability, or improvement of the PP crystal structure, which may increase pore size in the porous support layer. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39765.     

Effects of aging on poly(1‐trimethylsilyl‐1‐propyne) membranes irradiated with vacuum ultraviolet radiation for gas separation

In this study, we investigated the effects of physical aging on the surface and gas‐transport properties of highly gas permeable poly(1‐trimethylsilyl‐1‐propyne) membranes irradiated with vacuum ultraviolet (VUV) radiation. VUV excimer lamp irradiation was performed on one side of the membrane for 6 or 60 min. The gas permeabilities for carbon dioxide (CO₂) and nitrogen (N₂) were determined through a volumetric measurement method at 23 °C. The gas permeabilities for CO₂ and N₂ increased temporarily at 7 days after 6 and 60 min of VUV irradiation of the membranes. The change in the gas permeability for N₂ was more remarkable than that for CO₂. These changes were related to the C?O or SiO_x ratio. The C?O ratio was related to the gas permeability of the membranes VUV‐irradiated for 6 min, whereas the SiO_x ratio was related to the gas permeability of the membranes VUV‐irradiated for 60 min. These changes affected the gas selectivities of the membranes. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45973.     

Synthesis of phospholipidated β‐cyclodextrin and its application for flame‐retardant poly(lactic acid) with ammonium polyphosphate

In this study, phospholipidated β‐cyclodextrin (PCD) was obtained by the condensation between β‐cyclodextrin and phenyl phosphonic acid dichloride, which was characterized by Fourier transform infrared (FTIR) spectra, ¹H‐NMR, and thermogravimetric analysis (TGA). The thermal stability and flame retardancy of the poly(lactic acid) (PLA) blends [PLA–ammonium polyphosphate (APP)–PCD] were measured by TGA coupled to FTIR spectroscopy, vertical burning test (UL‐94), limiting oxygen index (LOI), and cone calorimetry tests. The results show that the mass ratio and loading amount of APP and PCD affected the properties of PLA. When the loading of APP and PCD was 30 wt % and the mass ratio of APP to PCD was 5:1, the highest LOI value of 42.6% (that of neat PLA was 19.7%) and a UL‐94 V0 rating were achieved, and the reduction of the total heat release was greater than 80%. Even when the total amount of APP and PCD was decreased to 20 wt % with the same mass ratio, the flame‐retardant PLA still can achieved a UL‐94 V0 rating. The improved performance was explained by the formation of an intumescent, continuous, contact char layer. Moreover, the reaction between APP and PCD contributed to the improvement of the thermal stability of the char residue. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46054.     

Effect of glucose fouling on the dissolved gases permeation through maximum‐crystallized poly(lactic acid) films

In this study, we investigated the effect of fouling on the dissolved oxygen and carbon dioxide permeation in water through maximum‐crystallized poly(lactic acid) (PLA) films by using proton nuclear magnetic resonance, attenuated total reflection‐Fourier transform infrared spectroscopy, wide‐angle X‐ray diffraction, and ultraviolet–visible spectroscopy, contact angle, water content ratio, and dissolved gas permeation. Fouling means the adhesion of contents on a container's internal surface, where content adhesion can directly influence the barrier property of the container. Glucose, a beverage ingredient, was used as a foulant. The permeation of dissolved gases in amorphous PLA film, maximum‐crystallized PLA film, and fouled maximum‐crystallized PLA film was determined. The decreased interstices in the polymer chains during crystallization resulted in the inhibition of the diffusion and decrease in the permeability coefficient of the gases. Moreover, the slope of the permeability coefficient for carbon dioxide in the Arrhenius plot was found smaller than that of oxygen's. This result indicated that the gas barrier property of dissolved carbon dioxide was considerably influenced by solubility and readily decreases during glucose fouling. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46604.     

Effect of the casting solvent on the free‐volume characteristics and gas permeability of poly[1‐(trimethylsilyl)‐1‐propyne] membranes

The effect of the casting solvent on the structure of poly[1‐(trimethylsilyl)‐1‐propyne] (PTMSP) membranes was investigated experimentally. The PTMSP membranes were cast from solutions of cyclohexane, toluene, and tetrahydrofuran; the membranes were characterized by the positron annihilation lifetime spectroscopy (PALS) technique and by gas‐permeation measurements of O₂, N₂, and CO₂. The decay curves from the positron annihilation lifetime spectroscopy gave the best fit when two long‐life components (τ₃ and τ₄, τ₃ < τ₄) were employed. This suggests that two types of free volume existed in the PTMSP membranes. The size and number density of τ₄, which was characteristic for PTMSP, decreased in the following order of the casting solvents: cyclohexane > toluene > tetrahydrofuran. The order was consistent with the order of gas permeability. A good correlation was observed between the permeability and the structural parameter that denoted the free‐volume size and the number density of τ₄. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 497–501, 2003     

Preparation and characterization of poly(ethylene terephthalate) copolyesters modified with sodium‐5‐sulfo‐bis‐(hydroxyethyl)‐isophthalate and poly(ethylene glycol)

Two types of poly(ethylene terephthalate) (PET) copolyesters were successfully prepared with sodium‐5‐sulfo‐bis‐(hydroxyethyl)‐isophthalate (SIPE) and poly(ethylene glycol) (PEG) units with different molecular weights named as cationic dyeable polyester and easy cationic dyeable polyester. Their chemical and crystalline structures were characterized by the nuclear magnetic resonance (NMR), wide angle X‐ray diffraction (WAXD), and small angle X‐ray scattering measurement, and their thermal properties were tested by differential scanning calorimetry and thermogravimetric analysis, respectively. NMR experimental results showed that the actual molar ratio of comonomers was basically consistent with the correlative feed ratio. WAXD results indicated that the crystalline structures of prepared copolyesters were similar to that of PET. Moreover, the glass transition temperature, melting temperature, and thermal degradation temperature were found to decrease with the reduction of the of PEG units as the incorporation of lower of PEG units brought more ether bonds into molecular chains, which increased the irregularity of molecular chain arrangement and led to lower crystallinity. In addition, because the incorporation of PEG units with lower molecular weight led to more ether bonds and hydroxyl end‐groups in molecular chains, the value of contact angle of PET copolyesters dropped, manifesting PET copolyesters had better hydrophilicity with the decreasing molecular weight of PEG units.© 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39823.     

Enhanced crystallization of poly(L‐lactide‐co‐ε‐caprolactone) in the presence of water

Poly(L ‐lactide‐co‐ε‐caprolactone) [P(LLA‐CL)], which is used in biodegradable biomedical materials such as drug‐delivery systems, surgical sutures, orthopedics, and scaffolds for tissue engineering, has been reported to crystallize upon storage in a dry state even at room temperature; this results in rapid changes in the mechanical properties. In biomedical applications, P(LLA‐CL) is used in the presence of water. This study investigated the effects of water on the crystallization of P(LLA‐CL) at 37°C in phosphate buffered solution, which was anticipated to alter its mechanical properties and hydrolytic degradation behavior. Surprisingly, the crystallinity of P(LLA‐CL) in the presence of water rapidly increased in 6–12 h and then slowly increased up to 120 h. The period of time for the initial rapid crystallization increase in the presence of water was much shorter than that in the absence of water. The obtained information would be useful for the selection, preparation, and use of P(LLA‐CL) in various biomedical applications. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Waterborne poly(urethane‐urea) gas permeation membranes for CO2/CH4 separation

In this work, dense membranes from aqueous dispersions of poly(urethane‐urea) (PUU) based on poly(propylene glycol) (PPG) and a block copolymer composed of poly(ethylene glycol) (PEG) and poly(propylene glycol) (PPG), EG‐b‐PG, with 7 wt % of the former were obtained. Nonpolluting formulations were synthesized with proportions of PPG and EG‐b‐PG as 1:0, 1:1, 1:3, and 3:1 in terms of equivalent number ratios. The effect of small and gradual increases in PEG segments was evaluated for the permeability of pure CO₂, CH₄, and N₂, at room temperature. Slight increases in PEG‐based segments in PUU promoted some remarkable properties, which led to a simultaneous increase in CO₂ permeability and ideal selectivity for CH₄ (300%) and N₂ (380%). Infrared spectroscopy showed that the PEG portions induced hydrogen bonds between ? NH of urethane and ether groups in the PEG portions, which promoted ordering of the flexible segments, confirmed by X‐ray diffractometry and small‐angle X‐ray scattering. Diffractometry techniques also confirmed the absence of crystalline domains, as did dynamic mechanical analysis. The produced membranes showed performance above Robeson's 2008 upper bound and seemed to be a superior polymeric material for CO₂/CH₄ and CO₂/N₂ separation. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46003.     

PFG‐NMR measurement of self‐diffusion coefficients of long‐chain α‐olefins and their mixtures in semi‐crystalline polyethylene

The self‐diffusion coefficients of C6–C16 long‐chain α‐olefins and their mixtures in semi‐crystalline polyethylene were measured through the pulsed field gradient nuclear magnetic resonance (PFG‐NMR). The effects of chain length, polyethylene (PE) type, and co‐monomer type in PE on the diffusion coefficients were investigated. Moreover, the influence of halohydrocarbon, cycloalkanes, and arene solvents on the diffusion coefficients of C12 α‐olefin in PE was characterized. The results have demonstrated that the diffusion coefficient of the single‐component α‐olefin in PE decreases exponentially with the increase of the carbon number of α‐olefin, and the crystallinity and crystal morphology of PE play a more important role than the co‐monomer type in determining the diffusion coefficients of α‐olefins. In addition, the apparent diffusion coefficients were used to represent the diffusion behaviors of the α‐olefin mixtures in PE. Owing to the presence of other hydrocarbon solvents, namely trichloromethane, cyclohexane, and benzene, the diffusion coefficients of C12 long‐chain α‐olefin in PE are significantly enhanced, and such promoting effect of the hydrocarbon solvents in polyolefin elastomer (POE) is much stronger than those in high‐density polyethylene (HDPE) and linear low‐density polyethylene (LLDPE). © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44143.     

Surface modification of ion‐exchange membranes: Methods,characteristics, and performance

Considerable effort has been made to improve ion‐exchange membrane (IEM) properties in order to achieve better performance of IEM‐based processes in various applications. Surface modification is one of the effective ways to improve IEM properties. Various methods have been used to modify IEM surfaces, for example, plasma treatment, polymerization, solution casting, electrodeposition, and ion implantation. These methods are able to produce a thin and fine distributed layer and also to modify the chemical structure of the surface. The new layer can be adsorbed, deposited, or chemically bonded on a membrane surface. By using these methods, IEM properties are improved, and the desired or specific characteristics such as high monovalent ion permselectivity, low fuel crossover, and anti‐organic‐fouling property can be obtained. In this paper, methods for surface modification of IEMs are reviewed. Moreover, the effects of modification on IEM properties and performance are discussed. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45540.     

Properties and structural characterization of oxidized starch/PVA/α‐zirconium phosphate composites

Two series of composites, i.e., polyvinyl alcohol (PVA)/oxidized starch (OST)/exfoliated α‐zirconium phosphate (POST‐ZrPn) and PVA/starch (ST)/exfoliated α‐zirconium phosphate (PST‐ZrPn), were fabricated using a casting and solvent evaporation method. The composites were characterized by Fourier transform infrared spectroscopy (FT‐IR), thermal gravimetric analysis (TGA), differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (XRD), scanning electron microscopy (SEM), tensile testing, and moisture uptake. Compared with PST‐ZrPn, POST‐ZrPn films with the same component ratio showed higher tensile strength (σ_b), lower elongation at break (ε_b) and improved water resistance. Additionally, in the POST‐ZrPn series, σ_b and ε_b increased with an increase in α‐zirconium phosphate (α‐ZrP) loading; however, higher α‐ZrP loads resulted in the aggregation of α‐ZrP particles. Compared with POST‐ZrP0, the values for σ_b, ε_b, and water resistance of POST‐ZrP3, containing 1.5 wt % α‐ZrP, were increased by 128.8%, 51.4%, and 30.2%, respectively. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010