Effect of GaAs (100) substrate misorientation on the electrical parameters and surface morphology of metamorphic In0.7Al0.3As/In0.75Ga0.25As/In0.7Al0.3As HEMT nanoheterostructures

The results of studies of the effect of GaAs (100) substrate misorientation on the electrical parameters and surface morphology of high electron mobility In_0.7Al_0.3As/In_0.75Ga_0.25As/In_0.7Al_0.3As/GaAs nanoheterostructures are reported. Using molecular-beam epitaxy, two identical structures with a stepped compositional profile of the metamorphic In _x Al_{1 ? x} As (Δ _x = 0.05) buffer are grown on substrates of two types: a singular GaAs substrate with the orientation (100) ± 0.5° and a GaAs (100) substrate misoriented by (2 ± 0.5)° in the $\left[ {0\bar 1\bar 1} \right]$ direction. It is found that, in the case of the misoriented substrate, the concentration of the two-dimensional electron gas is ～40% higher. Broadening of the photoluminescence spectra and a shift of the peaks to lower photon energies, as experimentally observed in the case of the misoriented substrate, are attributed to the increased roughness of the heterointerfaces and strengthened fluctuations of the quantum-well width.     

Application of photoluminescence spectroscopy to studies of In0.38Al0.62As/In0.38Ga0.62As/GaAs metamorphic nanoheterostructures

The results of studies of the surface morphology, electrical parameters, and photoluminescence properties of In_0.38Al_0.62As/In_0.38Ga_0.62As/In_0.38Al_0.62As metamorphic nanoheterostructures on GaAs substrates are reported. Some micron-sized defects oriented along the [011] and \([0\bar 11]\) directions and corresponding to regions of outcropping of stacking faults are detected on the surface of some heterostructures. The Hall mobility and optical properties of the samples correlate with the surface defect density. In the photoluminescence spectra, four emission bands corresponding to the recombination of charge carriers in the InGaAs quantum well (1–1.2 eV), the InAlAs metamorphic buffer (1.8–1.9 eV), the GaAs/AlGaAs superlattice at the buffer-substrate interface, and the GaAs substrate are detected. On the basis of experimentally recorded spectra and self-consistent calculations of the band diagram of the structures, the compositions of the alloy constituents of the heterostructures are established and the technological variations in the compositions in the series of samples are determined.     

Hall and photoluminescence studies of effects of the thickness of an additional In0.3Ga0.7As layer in the center of In0.15Ga0.85As/Al0.25Ga0.75As/GaAs high electron mobility transistors

In order to reduce the noise and carrier–donor scattering and thereby increase the carrier mobility of the pseudomorphic AlGaAs/InGaAs high electron mobility transistors (pHEMTs), we have grown Al_0.25Ga_0.75As/In_0.15Ga_0.85As/In_0.3Ga_0.7As/GaAs pHEMTs with varied In_0.3Ga_0.7As thickness, and studied the effects of the In_0.3Ga_0.7As thickness on the electron mobility and sheet density by Hall measurements and photoluminescence measurements. We calculated the electron and hole subbands and obtained good agreement between calculated and measured PL energies. It was found that the additional In_0.3Ga_0.7As layer could be used to reduce the carrier–donor scattering, but due to the increased interface roughness as the In_0.3Ga_0.7As layer becomes thicker, the interface scattering reduced the electron mobility. An optimal thickness of the In_0.3Ga_0.7As was found to be 2 nm.     

MHEMT with a power-gain cut-off frequency of f max = 0.63 THz on the basis of a In0.42Al0.58As/In0.42Ga0.58As/In0.42Al0.58As/GaAs nanoheterostructure

The method of molecular-beam epitaxy is used to grow a In_0.42Al_0.58As/In_0.42Ga_0.58As/In_0.42Al_0.58As nanoheterostructure with a step-graded metamorphic buffer on a GaAs substrate. The root-mean-square value of the surface roughness is 3.1 nm. A MHEMT (metamorphic high-electron-mobility transistor) with a zigzag-like gate of a length of 46 nm is fabricated on the basis of this nanoheterostructure; for this MHEMT, the cutoff frequencies for the current and power gain are f _T = 0.13 THz and f _max = 0.63 THz, respectively.     

Study of the influence of strained superlattices introduced into a metamorphic buffer on the electrophysical properties and the atomic structure of InAlAs/InGaAs MHEMT heterostructures

The results of studying the influence of strained superlattices introduced into a metamorphic buffer on the electrophysical properties and atomic crystal structure of In_0.70Al_0.30As/In_0.76Ga_0.24As/In_0.70Al_0.30As metamorphic high-electron-mobility transistor (MHEMT) nanoheterostructures on GaAs substrates are presented. Two types of MHEMT structures are grown by molecular beam epitaxy, namely, one with a linear increase in x in the In _x Al_{1 ? x} As metamorphic buffer, and the second with two mismatched superlattices introduced inside the metamorphic buffer. The electrophysical and structural parameters of the grown samples are studied by the van der Pauw method, transmission electron microscopy (including scanning and high-resolution microscopy), atomic-force microscopy, and energy dispersive X-ray analysis. It is revealed that the introduction of superlattices into a metamorphic buffer substantially improves the electrophysical and structural characteristics of MHEMT structures.     

Electrical behavior of modulation-and delta-doped Al x Ga1 − x As/In y Ga1 − y As/GaAs PHEMT structures

Modulation-and delta-doped Al_xGa_{1 ? x} As/In_yGa_{1 ? y} As/GaAs PHEMT structures are grown by MBE. The effect is examined of changes in the technique and level of doping on the electrical behavior of the structures. Photoluminescence spectroscopy combined with Hall-effect measurements is shown to be an effective strategy for the purpose. The experimental results are interpreted on the basis of calculated conductionband diagrams.     

The effect of strained Al0.7In0.3As emitter layers on abrupt N-p+ AllnAs-GaInAs heterojunction diodes and heterojunction bipolar transistors

Strained Al_xIn_1−xAs/Ga_0.47In_0.53As heterojunction N-p⁺ diodes and heterojunction bipolar transistors (HBTs) have been grown on InP substrates by solid-source molecular-beam epitaxy, fabricated, and characterized. To determine the effects of the conduction-band discontinuity at the emitter-base heterojunction on turn-on voltage and ideality factor, a strained Al_0.7In_0.3As layer is inserted in the emitter near the base. Changes in transport across the junction are observed as a function of the strained-layer position and thickness. These results were used to implement strained emitter HBTs.     

Persistent photo-conductance and photoquenching of selectively doped Al0.3Ga0.7As GaAs/heterojunctions

The dependence on photon energy of the persistent photoconductivity (PPC) in selectively doped high mobility Al_0.3Ga_0.7As—GaAs heterostructures has been measured at temperatures below 80 K. A decrease in conductivity due to light exposure at one wavelength after exposure to light at another wavelength — photo-quenching — is also found. It is concluded that deep centers in GaAs and AlGaAs other than the DX center in AlGaAs are mainly responsible for PPC.     

Characterization of In x Ga1−x As/GaAs quantum-well heterostructures by C-V measurements: Band offsets, quantum-confinement levels, and wave functions

The method of C-V profiling combined with self-consistent solution of Schrödinger’s and Poisson’s equations was used to determine with high precision the absolute values of the conduction-band offsets, energies of quantum-confinement levels, and charge-carrier concentrations in quantum-confinement subbands of In _x Ga_1?x As/GaAs quantum-well heterostructures with In content corresponding to the pseudomorphic growth mode (0 < x < 0.3). A characterization technique based on capacitance measurements is developed, enabling one to determine the main electronic parameters of quantum-confinement heterostructures.     

Thermal characteristics of InP, InAlAs, and AlGaAsSb metamorphic buffer layers used in In0.52Al0.48As/In0.53Ga0.47As heterojunction bipolar transistors grown on GaAs substrates

In_0.52Al_0.48As/In_0.53Ga_0.47As heterojunction bipolar transistors (HBTs) were grown metamorphically on GaAs substrates by molecular beam epitaxy. In these growths, InAlAs, AlGaAsSb, and InP metamorphic buffer layers were investigated. The InAlAs and AlGaAsSb buffer layers had linear compositional grading while the InP buffer layer used direct binary deposition. The transistors grown on these three layers showed similar characteristics. Bulk thermal conductivities of 10.5, 8.4, and 16.1 W/m K were measured for the InAlAs, AlGaAsSb, and InP buffer layers, as compared to the 69 W/m K bulk thermal conductivity of bulk InP. Calculations of the resulting HBT junction temperature strongly suggest that InP metamorphic buffer layers should be employed for metamorphic HBTs operating at high power densities.     

Type I and Type II Alignment of the Light Hole Band in In0.15Ga0.85As/GaAs and in ln0.15Ga0.85As/Al0.15Ga0.85As Strained Quantum Wells

We present results of photoluminescence and cathodoluminescence measurements of strained undoped In_0.15Ga_0.85As/GaAs and In_0.15Ga_0.85As/Al_0.15Ga_0.85As quantum well structures, designed to throw light on the current controversy over light-hole band alignment at low In content. We compare these data with theoretical calculations of the confined state energies within the eight band effective mass approximation. Our analysis shows that for In_0.15Ga_0.85As/GaAs, the observed two transitions are consistent with either type I or type II alignment of the light hole band for band offset ratios within the accepted range. In the case of In_0.15Ga_0.85As/Al_0.15Ga_0.85As, however, our results clearly indicate type II alignment for the light hole band. We derive the band offset ratio Q, defined here as Q = δE_c/δE_g where δE_c is the conduction band offset and δE_g is the bandgap difference between the quantum well and the barrier in the presence of strain, for the In_0.15Ga_0.85As/Al_0.15Ga_0.85As system to be Q = 0.83 and discuss it in the context of the common anion rule.     

Dislocation-Induced deep level states in In0.08Ga0.92As/GaAs heterostructures

We have performed luminescence experiments on In_0.08Ga_0.92As/GaAs heterointerfaces to explore the energy distribution of deep level states in the bandgap for two cases: (1) unrelaxed, pseudomorphic In_0.08Ga_0.92As films (200Å thick), which have few if any dislocations at the interface, and (2) partially relaxed In_0.08Ga_0.92As films (1000Å thick) which are expected to have a substantial interfacial dislocation density. A combined photoluminescence and cathodoluminescence technique is used which allows us to profile the sample luminescence through the buried interface region. Our results show the existence of deep level luminescent features characteristic of the GaAs substrate and features common to In_0.08Ga_0.92As and GaAs, as well as the existence of a deep level feature near 1 eV photon energy which undergoes a shift in energy depending upon the degree of strain relaxation in the In_0.08Ga_0.92As film. In addition, a deep level feature near 0.83 eV becomes prominent only in In_0.08Ga_0.92As films which have relaxed, and thus contain misfit dislocations at the interface. These deep level differences may be due to bandgap states associated with the intrinsic dislocation structure, impurities segregated at the dislocation, or bulk point defects, or threading dislocations generated during the strain relaxation. Previous work has determined that a deep level state 0.7 eV above the valence band edge would account for the electrical behavior of relaxed In_0.08Ga_0.92As/GaAs interfaces, which is in good agreement with the range of deep level transitions near 0.8 eV photon energy which we observe. These measurements suggest that photo- and cathodoluminescence measurements of deep level emission in these III-V semiconductors can provide a useful indicator of electrically active defect densities associated with misfit dislocations.     

Band-edge line-up in GaAs/GaAsN/InGaAs heterostructures

Triple GaAs/GaAsN/InGaAs heterostructures were grown by MBE on GaAs substrates, and their optical properties were studied. The band-edge line-up in GaAs/GaAsN and InGaAs/GaAsN heterostructures was analyzed by correlating the experimental photoluminescence spectra with the known parameters of the band diagram in (In,Ga)As compounds. It is shown that a GaAs/GaAsN heterojunction is type I, while an In_xGa_1?x As/GaAsN heterojunction can be type I or type II, depending on the In content x.     

Persistent photoconductivity and electron mobility in In0.52Al0.48As/In0.53Ga0.47As/In0.52Al0.48As/InP quantum-well structures

The influence of the width of the quantum well L and doping on the band structure, scattering, and electron mobility in nanoheterostructures with an isomorphic In_0.52Al_0.48As/In_0.53Ga_0.47As/In_0.52Al_0.48As quantum well grown on an InP substrate are investigated. The quantum and transport mobilities of electrons in the dimensionally quantized subbands are determined using Shubnikov-de Haas effect measurements. These mobilities are also calculated for the case of ionized-impurity scattering taking into account intersub-band electron transitions. It is shown that ionized-impurity scattering is the dominant mechanism of electron scattering. At temperatures T < 170 K, persistent photoconductivity is observed, which is explained by the spatial separation of photoexcited charge carriers.     

Room temperature λ=1.3 µm photoluminescence from InGaAs quantum dots on (001) Si substrate

GaAs/In_xGa_1−x As quantum dot heterostructures exhibiting high-intensity λ=1.3 μm photoluminescence at room temperature have been grown on (001) Si substrate with a Si_1−x Ge_x buffer layer. The growth was done successively on two MBE machines with sample transfer via the atmosphere. The results obtained by the study of the structure growth process by means of high-energy electron diffraction are presented. __________ Translated from Fizika i Tekhnika Poluprovodnikov, Vol. 36, No. 5, 2002, pp. 565–568. Original Russian Text Copyright ? 2002 by Burbaev, Kazakov, Kurbatov, Rzaev, Tsvetkov, Tsekhosh.     

Thermal stability of Al0.48In0.52As/Ga0.47In0.53As/InP heterostructure and its improvement by phosphidization

A drastic decrease in the sheet carrier concentration of modulation-doped Al_0.48In_0.52As/Ga_0.47In_0.53As/InP heterostructures has been observed after O₂ plasma treatment followed by thermal treatment up to 350°C. The decrease in sheet carrier concentration, which is speculated to be caused by both plasma damage and impurities penetrating from the surface of the epilayer, can be suppressed substantially by using PH₃ plasma treatment prior to the O₂ plasma and thermal treatments.     

Growth of In-Rich In x Al1−x N Films on (0001) Sapphire by RF-MBE and their Properties

In-rich In _x Al_1−x N films (0.47 ≤ x ≤ 1) were grown directly on nitridated (0001) sapphire substrates without employing a buffer layer by radiofrequency molecular-beam epitaxy. Both photoluminescence peak energy and optical absorption-edge energy of the In _x Al_1−x N films decreased monotonically with increasing In composition, which was consistent with the recently reported InN bandgap energies of ∼0.7 eV. The bowing parameter of this alloy was estimated to lie between 2.9 eV and 6.2 eV. Substrate nitridation with lower temperature and longer period conditions not only reduced misoriented In _x Al_1−x N phases remarkably but also produced narrower tilt distribution in the c-axis-oriented In _x Al_1−x N matrix.     

Diffusion of zinc into gaas through Al0.3Ga00.7As

The diffusion of zinc into GaAs, Al_0.3Ga_0.7As and Al_0.3Ga_0.7As/GaAs single heterostructures have been studied. The depth of the diffusion front is found to be proportional to the square root of the diffusion time, [t]^1/2, and for single heterostructures the Al_0.3Ga_0.7As layer thickness,d ₁ modifies this relationship through decreasing the junction depth byd ₁ multiplied by a constant. It is shown that this relationship can be used for predicting diffusion fronts in double heterostructures.     

Superstructured ordering in Al x Ga1 − x As and Ga x In1 − x P alloys

Epitaxial heterostructures produced on the basis of Al _x Ga_{1 ? x} As and Ga _x In_{1 ? x} P ternary alloys by metal-organic chemical vapor deposition are studied. The composition parameter x of the alloys was ～0.50. By X-ray diffraction studies, scanning electron microscopy, atomic force microscopy, and photoluminescence spectroscopy, it is shown that superstructured ordered phases with the stoichiometry composition III_{1 ? η}III_{1 + η}V₂ can be formed. As a consequence of this effect, not only does the cubic crystal symmetry change to the tetragonal type in the new compound, but also the optical properties become different from those of disordered alloy with the same composition.     

Electrical characteristics of low temperature-Al0.3Ga0.7As

In this work, we present electrical characterizations of n⁺ GaAs/low temperature (LT)-Al_0.3Ga_0.7As/n⁺ GaAs resistor structures in which the LT layers are grown at nominal substrate temperatures of 250 and 300°C. The resistivity and V_tfl parameters of these LT-Al_0.3Ga_0.7As layers are compared with those of LT-GaAs and Al_0.3Ga_0.7As grown at a normal growth temperature of 720°C. Low-temperature Al_0.3Ga_0.7As layers exhibit resistivities as high as 10¹² ohm-cm, nearly four orders of magnitude higher than that of LT-GaAs, and V_tfl values as high as 45 V, over twice that of LT-GaAs. We also find that the LT-Al_0.3Ga_0.7As materials grown at 250 and 300°C appear to show opposite and contradictory trends with respect to resistivity and V_tfl. We propose that this result can be explained by residual hopping conduction in the 250°C material. Temperature dependent conductivity measurements confirm the presence of a hopping mechanism in LT-Al_0.3Ga_0.7As grown at 250°C and yield activation energies of 0.77 and 0.95 eV for LT-GaAs and LT-Al_0.3Ga_0.7As, respectively.