共查询到20条相似文献,搜索用时 15 毫秒
1.
2.
3.
4.
针对压电陶瓷振子的Q值较低,参数离散性比较大的特点,从提高线路的选择性入手,设计了一种高精度的压电陶瓷振子频率自动测试仪,它能自动显示出压电陶瓷振子的谐振和反谐振频率。对于频率为3kHz~1.2MHz的瓷片,测试精度一般不低于千分之二。 相似文献
5.
6.
这里向大家介绍一种用双迹示波器测量压电晶体谐振频率的方法。这种方法和阻抗——电压法相比,优点是测试准确,既可测串联谐振频率,又可测并联谐振频率。压电晶体的等效电路如图1所示。其中 C_0为静态电容,L_1、C_1、r 代表压电晶体的动态参数。此等效电路的阻抗——频率特性如图2所示。从图中可看出,压电晶体 相似文献
7.
8.
9.
10.
对自由压电陶瓷片,组合电声换能器.600W的超声清洗器.1200W的超声发生器的振动模式频率进行了测量及互相比较.在由一对瓷片和其它金属部分构成的组合振子中.轴向模从398kHz下降至31.6kHz.从而低于径向模的谐振频率41.9kHz.在由27个组合振子构成的阵列中.居间频率范围内出现一个轴向和径向的强烈耦合模.超声清洗器水槽中深h的水是一个水声谐振腔,压电振子的谐振条件为h=(2n+1)λ/4. 相似文献
11.
《Proceedings of the IEEE. Institute of Electrical and Electronics Engineers》1980,68(8):1032-1033
A new equivalent circuit is considered for piezoelectric ceramic radial mode disk resonators. The new circuit has been obtained by connecting a resistance element in series with a commonly used equivalent circuit, so that it is usable for a better simulation of the frequency characteristics of the resonator impedance. 相似文献
12.
13.
压电谐振器是谐振式传感器和执行器的核心部件,通常工作在共振和稳幅状态。采用一种锁相环(PLL)和自动增益(AGC)相结合的双闭环控制驱动电路,分别实现了谐振器共振频率的跟踪激励和压电振子输出信号的稳幅控制。优化设计了双闭环电路中各元器件参数,使得压电振子能稳定工作在谐振频率点。参照压电谐振器开环测试数据和闭环测试数据,双闭环驱动电路能将谐振器相位锁定在59°(误差3°),输出信号峰峰值稳定在12.8V(误差0.2V)。实验结果表明,该电路设计能够达到稳定谐振器输出信号幅值和跟踪谐振器共振频率的目的。 相似文献
14.
自由振动压电振子的一种复参数等效电路 总被引:2,自引:1,他引:1
将复数概念引入到等效电路元件参数中,并以自由振动压电振子的一种常用振动模——纵向长度伸缩振动模为例,给出了一种复参数等效电路,并推导了等效电路参数与压电材料参数之间相互关系。等效电路元件参数的虚部表示压电振子机械、介电、及压电损耗。给出了由复参数等效电路模型作出的阻抗圆图与由振动理论给出的阻抗圆图以及由传统模型所作出的阻抗圆图。结果表明,新的复参数模型优于传统模型,是一种精确的等效电路。 相似文献
15.
受环境因素的影响,压电谐振器的共振频率会发生漂移。调谐技术因采用特定的手段主动调节共振频率而得到广泛应用,但传统附加质量块、激光烧蚀等机械调谐技术费时费力,灵活性不好。针对方体压电谐振器该文提出了一种激励信号幅值调谐和直流调谐的电调谐方法,可精密调节谐振器的共振频率。设计了一种基于ZYNQ系列主控芯片的数字化测控电路,实现了振子扫频激励、输出信号的幅值相位检测,为激励信号幅值调谐和直流调谐提供了实验硬件平台。实验结果表明,激励信号幅值调谐的共振频率变化范围为347.850~348.000 kHz,直流调谐的调节范围为347.720~347.820 kHz。该技术为压电谐振器共振频率精密调节提供可靠的理论与实践途径。 相似文献
16.
压电陶瓷圆片振子耦合振动的等效电路 总被引:1,自引:1,他引:1
在考虑压电效应的情况下,本文对压电陶瓷圆片形振子的耦合振动进行了研究,分析了振子的轴向振动与径向振动之间的相互关系,推出了振子耦合振动的等效电路.在此基础上,得出了振子耦合振动的共振频率方程,并分析了振子的振动模式与共振频率之间的关系.理论分析表明,压电陶瓷振子耦合振动的等效电路在其频率特性分析中是非常方便的,理想振子的一维振动模式是实际振子的一些近似振动模式.可由本文理论直接导出.实验表明,由本文理论得出的振子的共振频率与实测值符合很好. 相似文献
17.
《Microwave Theory and Techniques》1981,29(7):689-699
An important class of commercial three-port circulator relies for its operation on a junction resonator consisting of the symmetrical connection of three open-circuited transmission lines. A feature of this resonator is that it may be quarter-wave coupled to form a circulator with a moderate specification (25-percent bandwidth to 25-dB return loss points) and physical dimensions of the order of directly coupled conventional circulators (using a disk resonator). For circulators for which the in-phase eigennetwork may be represented by an ideal short-circuit, the equivalent circuit is a one-port network which may be formed from a characterization of the constituent resonator. This feature is used in this paper to study the equivalent circuit of junction circulators using planar WYE resonators. The derivation of the equivalent circuit parameters is supported with the design of a 4-GHz quarter-wave-coupled stripline circulator. 相似文献
18.
The impedance matrix for an arbitrary n -port ferrimagnetic resonator is derived by applying Poynting's theorem to a region of space surrounding the resonator. Simplifications to the impedance matrix for low-loss (Q >≈100) ferrite material make it possible to obtain an equivalent circuit model for the resonator, which can be used with most computer-based circuit simulation programs. The circuit model for the general-case polymodal ferrimagnetic resonator consists of a network of single-pole resonators, each of which has a possible non-frequency-dependent, nonreciprocal phase shift. The components of the circuit model are described in terms of the properties of the ferrite material, and the coupling strength of the microwave circuit to the magnetostatic modes of the ferrimagnet. The method is demonstrated in three simple examples, including a one- and two-port loop coupled filter, and a ferrimagnet in a waveguide 相似文献
19.
20.
针对压电谐振器振动特性分析的应用需求,构建了一种小型化、廉价的矢量分析系统。系统采用STM32控制4路DDS芯片产生驱动信号和矢量解析正交信号。通过向DDS芯片写频率控制字,对压电谐振器进行扫频驱动。同时采用STM32内置ADC,采样并计算获取各频率点压电谐振器输出信号的幅值和相位。通过提取压电谐振器两个特殊振动模态下的共振频率、品质因数(Q值)、输出信号相位等振动特性参数,获得驱动信号对这些参数的影响规律,系统分析了驱动信号对压电谐振器振动特性的影响,为压电谐振器的驱动、信号检测提供了有效的技术途径,实验结果为压电谐振器振动特性分析提供了依据。 相似文献