SnO2: A Wonderful Electron Transport Layer for Perovskite Solar Cells

The highest power conversion efficiency of perovskite solar cells is beyond 22%. Charge transport layers are found to be critical for device performance and stability. A traditional electron transport layer (ETL), such as TiO₂, is not very efficient for charge extraction at the interface, especially in planar structure. In addition, the devices using TiO₂ suffer from serious degradation under ultraviolet illumination. SnO₂ owns a better band alignment with the perovskite absorption layer and high electron mobility, which is helpful for electron extraction. In this Review, recent progresses in efficient and stable perovskite solar cells using SnO₂ as ETL are summarized.     

Improved Performance of Printable Perovskite Solar Cells with Bifunctional Conjugated Organic Molecule

A bifunctional conjugated organic molecule 4‐(aminomethyl) benzoic acid hydroiodide (AB) is designed and employed as an organic cation in organic–inorganic halide perovskite materials. Compared with the monofunctional cation benzylamine hydroiodide (BA) and the nonconjugated bifunctional organic molecule 5‐ammonium valeric acid, devices based on AB‐MAPbI₃ show a good stability and a superior power conversion efficiency of 15.6% with a short‐circuit current of 23.4 mA cm^?2, an open‐circuit voltage of 0.94 V, and a fill factor of 0.71. The bifunctional conjugated cation not only benefits the growth of perovskite crystals in the mesoporous network, but also facilitates the charge transport. This investigation helps explore new approaches to rational design of novel organic cations for perovskite materials.     

TiO2 Electron Transport Bilayer for Highly Efficient Planar Perovskite Solar Cell

In planar perovskite solar cells, it is vital to engineer the extraction and recombination of electron–hole pairs at the electron transport layer/perovskite interface for obtaining high performance. This study reports a novel titanium oxide (TiO₂) bilayer with different Fermi energy levels by combing atomic layer deposition and spin‐coating technique. Energy band alignments of TiO₂ bilayer can be modulated by controlling the deposition order of layers. The TiO₂ bilayer based perovskite solar cells are highly efficient in carrier extraction, recombination suppression, and defect passivation, and thus demonstrate champion efficiencies up to 16.5%, presenting almost 50% enhancement compared to the TiO₂ single layer based counterparts. The results suggest that the bilayer with type II band alignment as electron transport layers provides an efficient approach for constructing high‐performance planar perovskite solar cells.     

Printable CsPbI3 Perovskite Solar Cells with PCE of 19% via an Additive Strategy

All-inorganic CsPbI₃ holds promise for efficient tandem solar cells, but reported fabrication techniques are not transferrable to scalable manufacturing methods. Herein, printable CsPbI₃ solar cells are reported, in which the charge transporting layers and photoactive layer are deposited by fast blade-coating at a low temperature (≤100 °C) in ambient conditions. High-quality CsPbI₃ films are grown via introducing a low concentration of the multifunctional molecular additive Zn(C₆F₅)₂, which reconciles the conflict between air-flow-assisted fast drying and low-quality film including energy misalignment and trap formation. Material analysis reveals a preferential accumulation of the additive close to the perovskite/SnO₂ interface and strong chemisorption on the perovskite surface, which leads to the formation of energy gradients and suppressed trap formation within the perovskite film, as well as a 150 meV improvement of the energetic alignment at the perovskite/SnO₂ interface. The combined benefits translate into significant enhancement of the power conversion efficiency to 19% for printable solar cells. The devices without encapsulation degrade only by ≈2% after 700 h in air conditions.     

Improving the Electron Transport Performance of TiO2 Film by Regulating TiCl4 Post-Treatment for High-Efficiency Carbon-Based Perovskite Solar Cells

Titanium oxide (TiO₂) has been widely used as an electron transport layer (ETL) in perovskite solar cells (PSCs). Typically, TiCl₄ post-treatment is indispensable for modifying the surfaces of TiO₂ ETL to improve the electron transport performance. However, it is challenging to produce the preferred anatase phase-dominated TiO₂ by the TiCl₄ post-treatment due to the higher thermodynamic stability of the rutile phase. In this work, a mild continuous pH control strategy for effectively regulating the hydrolysis process of TiCl₄ post-treatment is proposed. As the weak organic base, urea has been demonstrated can maintain a moderate pH decrease during the hydrolysis process of TiCl₄ while keeping the hydrolysis process relatively mild due to the ultra-weak alkalinity. The improved pH environment is beneficial for the formation of anatase TiO₂. Consequently, a uniform anatase-dominated TiO₂ surface layer is formed on the mesoporous TiO₂, resulting in reduced defect density and superior band energy level. The interfacial charge recombination is effectively suppressed, and the charge extraction efficiency is improved simultaneously in the fabricated solar cells. The efficiency of the fabricated carbon electrode-based PSCs (C-PSCs) is improved from 16.63% to 18.08%, which is the highest for C-PSCs based on wide-bandgap perovskites.     

Strategically Constructed Bilayer Tin (IV) Oxide as Electron Transport Layer Boosts Performance and Reduces Hysteresis in Perovskite Solar Cells

Nanostructured tin (IV) oxide (SnO₂) is emerging as an ideal inorganic electron transport layer in n–i–p perovskite devices, due to superior electronic and low‐temperature processing properties. However, significant differences in current–voltage performance and hysteresis phenomena arise as a result of the chosen fabrication technique. This indicates enormous scope to optimize the electron transport layer (ETL), however, to date the understanding of the origin of these phenomena is lacking. Reported here is a first comparison of two common SnO₂ ETLs with contrasting performance and hysteresis phenomena, with an experimental strategy to combine the beneficial properties in a bilayer ETL architecture. In doing so, this is demonstrated to eliminate room‐temperature hysteresis while simultaneously attaining impressive power conversion efficiency (PCE) greater than 20%. This approach highlights a new way to design custom ETLs using functional thin‐film coatings of nanomaterials with optimized characteristics for stable, efficient, perovskite solar cells.     

以ZnO纳米棒阵列为电子传输层的无空穴层有机-无机杂化钙钛矿太阳能电池

近年来,有机-无机杂化钙钛矿太阳能电池(PSCs)发展迅速,其光电转化效率(PCE)已提升至23.3%,成为当今太阳能电池领域无可争议的研究焦点。研究发现,PSCs结构组成与性质对光电性能影响显著。其中,电子传输层的形貌结构不仅影响钙钛矿晶体的成长,同时也决定了电子扩散系数和电子寿命。本工作将ZnO纳米棒阵列(Nanorods array,NRAs)作为电子传输层,应用于无空穴传输层的基于碳对电极的杂化钙钛矿太阳能电池中。通过水热法制备了不同长度的ZnO NRAs,经测试发现,对应的钙钛矿电池的PCE随ZnO NRAs长度的增加呈先升高后下降的趋势,当ZnO NRAs长度为454 nm时,PCE最优为6.18%。     

To Be Higher and Stronger—Metal Oxide Electron Transport Materials for Perovskite Solar Cells

Organometallic mixed halide perovskite solar cells (PSCs) have emerged as a promising photovoltaic technology with increasingly improved device efficiency exceeding 24%. Charge transport layers, especially electron transport layers (ETLs), are verified to play a vital role in device performance and stability. Recently, metal oxides (MOs) have been widely studied as ETLs for high‐performance PSCs due to their excellent electronic properties, superb versatility, and great stability. This Review briefly discusses the development of PSCs' architecture and outlines the requirements for MO ETLs. Additionally, recent progress of MO ETLs from preparation to optimization for efficient PSCs is systematically summarized and highlighted to associate the versatility of MO ETLs with the performance of devices. Finally, a summary and prospectives for the future development of MO ETLs toward practical application of high‐performance PSCs are drawn.     

Low‐Temperature In Situ Amino Functionalization of TiO2 Nanoparticles Sharpens Electron Management Achieving over 21% Efficient Planar Perovskite Solar Cells

Titanium oxide (TiO₂) has been commonly used as an electron transport layer (ETL) of regular‐structure perovskite solar cells (PSCs), and so far the reported PSC devices with power conversion efficiencies (PCEs) over 21% are mostly based on mesoporous structures containing an indispensable mesoporous TiO₂ layer. However, a high temperature annealing (over 450 °C) treatment is mandatory, which is incompatible with low‐cost fabrication and flexible devices. Herein, a facile one‐step, low‐temperature, nonhydrolytic approach to in situ synthesizing amino‐functionalized TiO₂ nanoparticles (abbreviated as NH₂‐TiO₂ NPs) is developed by chemical bonding of amino (‐NH₂) groups, via Ti? N bonds, onto the surface of TiO₂ NPs. NH₂‐TiO₂ NPs are then incorporated as an efficient ETL in n‐i‐p planar heterojunction (PHJ) PSCs, affording PCE over 21%. Cs_0.05FA_0.83MA_0.12PbI_2.55Br_0.45 (abbreviated as CsFAMA) PHJ PSC devices based on NH₂‐TiO₂ ETL exhibit the best PCE of 21.33%, which is significantly higher than that of the devices based on the pristine TiO₂ ETL (19.82%) and is close to the record PCE for devices with similar structures and fabrication procedures. Besides, due to the passivation of the surface trap states of perovskite film, the hysteresis of current–voltage response is significantly suppressed, and the ambient stability of devices is improved upon amino functionalization.     

Recent Progress in Organic Electron Transport Materials in Inverted Perovskite Solar Cells

Organic n‐type materials (e.g., fullerene derivatives, naphthalene diimides (NDIs), perylene diimides (PDIs), azaacene‐based molecules, and n‐type conjugated polymers) are demonstrated as promising electron transport layers (ETLs) in inverted perovskite solar cells (p–i–n PSCs), because these materials have several advantages such as easy synthesis and purification, tunable frontier molecular orbitals, decent electron mobility, low cost, good solubility in different organic solvents, and reasonable chemical/thermal stability. Considering these positive factors, approaches toward achieving effective p–i–n PSCs with these organic materials as ETLs are highlighted in this Review. Moreover, organic structures, electron transport properties, working function of electrodes caused by ETLs, and key relevant parameters (PCE and stability) of p–i–n PSCs are presented. Hopefully, this Review will provide fundamental guidance for future development of new organic n‐type materials as ETLs for more efficient p–i–n PSCs.     

Origins of High Performance and Degradation in the Mixed Perovskite Solar Cells

The origins of the high device performance and degradation in the air are the greatest issues for commercialization of perovskite solar cells. Here this study investigates the possible origins of the mixed perovskite cells by monitoring defect states and compositional changes of the perovskite layer over the time. The results of deep‐level transient spectroscopy analysis reveal that a newly identified defect formed by Br atoms exists at deep levels of the mixed perovskite film, and its defect state shifts when the film is aged in the air. The change of the defect state is originated from loss of the methylammonium molecules of the perovskite layer, which results in decreased J_SC, deterioration of the power conversion efficiency and long‐term stability of perovskite solar cells. The results provide a powerful strategy to diagnose and manage the efficiency and stability of perovskite solar cells.     

染料敏化太阳能电池光阳极TiO2薄膜的研究进展

在概述染料敏化太阳能电池工作原理基础上,着重分析电池光阳极TiO2薄膜的特性,并指出该薄膜在电池中所起的作用:负载染料、收集光生电子、分离电荷和传输光生电子;继而从表面修饰、离子掺杂、量子点敏化、制备复合薄膜、设计微观有序空间结构、设计核壳结构以及多手段共改性等方面对TiO2薄膜改性手段进行综述,并详细分析改性手段优化染料敏化太阳能电池性能的原因;最后,提出应把优化光阳极TiO2薄膜制备工艺及探讨薄膜接触面工作机理等作为今后的研究重点。     

Historical Analysis of High-Efficiency,Large-Area Solar Cells: Toward Upscaling of Perovskite Solar Cells

The status and problems of upscaling research on perovskite solar cells, which must be addressed for commercialization efforts to be successful, are investigated. An 804 cm² perovskite solar module has been reported with 17.9% efficiency, which is significantly lower than the champion perovskite solar cell efficiency of 25.2% reported for a 0.09 cm² aperture area. For the realization of upscaling high-quality perovskite solar cells, the upscaling and development history of conventional silicon, copper indium gallium sulfur/selenide and CdTe solar cells, which are already commercialized with modules of sizes up to ≈25 000 cm², are reviewed. GaAs, organic, dye-sensitized solar cells and perovskite/silicon tandem solar cells are also reviewed. The similarities of the operating mechanisms between the various solar cells and the origin of different development pathway are investigated, and the ideal upscaling direction of perovskite solar cells is subsequently proposed. It is believed that lessons learned from the historical analysis of various solar cells provide a fundamental diagnosis of relative and absolute development status of perovskite solar cells. The unique perspective proposed here can pave the way toward the upscaling of perovskite solar cells.     

钙钛矿太阳能电池的研究进展

作为一种新型清洁可再生能源,钙钛矿太阳能电池(Perovskite solar cells,PSC)从发展至今已取得了重大的突破,成为研究的热点。主要介绍了钙钛矿太阳能电池的基本结构和工作原理及电子传输层、钙钛矿层、空穴传输层的制备方法,以及在发展过程中所面临的技术问题,最后展望了钙钛矿太阳能电池未来的研究重点及发展前景。