Electrospinning fabrication and characterization of poly(vinyl alcohol)/montmorillonite nanofiber mats

Poly(vinyl alcohol) (PVA)/montmorillonite clay (MMT) nanofiber mats have been fabricated by the electrospinning technique. The PVA/MMT nanofiber mats were characterized by X‐ray diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), Fourier transform infrared (FTIR), and mechanical measurements. The study showed that the introduction of MMT results in improvement in tensile strength, and thermal stability of the PVA matrix. XRD patterns and SEM micrographs suggest the coexistence of exfoliated MMT layers over the studied MMT contents. FTIR revealed that there might be possible interaction occurred between the MMT clay and PVA matrix. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Structure‐property and swelling behavior of electron beam irradiated poly(vinyl alcohol)/acrylamide/sodium montmorillonite clay composites

Composites based on poly(vinyl alcohol) (PVA), acrylamide monomer (AM) and sodium montmorillonite clay (MMT) were prepared, in the form of thin films, by solution casting. The PVA/AM/MMT composites films were then exposed to electron beam irradiation to form crosslinked network structure. The structure‐property behavior of PVA/AM/MMT hybrids was demonstrated by x‐ray diffraction (XRD), scanning electron microscopy, gel content, color intensity, thermogravimetric analysis (TGA) and swelling behavior in aqueous solutions. The results indicated that the introduction of MMT clay ratio up to 5% decreased the gel content of PVA/AM hydrogels. The color measurements indicated that the introduction of MMT clay ratio up to 5% was shown to affect the color intensity of composite films. It was found that both PVA/AM hydrogels and PVA/AM/MMT composites reached the equilibrium swelling state in water after four hours; however PVA/AM/MMT composites displayed higher swelling than PVA/AM hydrogels. However, the swelling of PVA/AM hydrogels or their composites at the equilibrium state increased with increasing temperature up to 60°C. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Poly(vinyl alcohol) nanocomposites with different clays: Pristine clays and organoclays

Poly(vinyl alcohol) (PVA)/clay nanocomposites were synthesized using the solution intercalation method. Na ion‐exchanged clays [Na⁺–saponite (SPT) and Na⁺–montmorillonite (MMT)] and alkyl ammonium ion‐exchanged clays (C₁₂–MMT and C₁₂OOH–MMT) were used for the PVA nanocomposites. From the morphological studies, the Na ion‐exchanged clay is more easily dispersed in a PVA matrix than is the alkyl ammonium ion‐exchanged clay. Attempts were also made to improve both the thermal stabilities and the tensile properties of PVA/clay nanocomposite films, and it was found that the addition of only a small amount of clay was sufficient for that purpose. Both the ultimate tensile strength and the initial modulus for the nanocomposites increased gradually with clay loading up to 8 wt %. In C₁₂OOH–MMT, the maximum enhancement of the ultimate tensile strength and the initial modulus for the nanocomposites was observed for blends containing 6 wt % organoclay. Na ion‐exchanged clays have higher tensile strengths than those of organic alkyl‐exchanged clays in PVA nanocomposites films. On the other hand, organic alkyl‐exchanged clays have initial moduli that are better than those of Na ion‐exchanged clays. Overall, the content of clay particles in the polymer matrix affect both the thermal stability and the tensile properties of the polymer/clay nanocomposites. However, a change in thermal stability with clay was not significant. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3208–3214, 2003     

Structural characterization of hydrophilic polymer blends/montmorillonite clay nanocomposites

The nanocomposite films comprising polymer blends of poly(vinyl alcohol) (PVA), poly(vinyl pyrrolidone) (PVP), poly(ethylene oxide) (PEO), and poly(ethylene glycol) (PEG) with montmorillonite (MMT) clay as nanofiller were prepared by aqueous solution casting method. The X‐ray diffraction studies of the PVA–x wt % MMT, (PVA–PVP)–x wt % MMT, (PVA–PEO)–x wt % MMT and (PVA–PEG)–x wt % MMT nanocomposites containing MMT concentrations x = 1, 2, 3, 5 and 10 wt % of the polymer weight were carried out in the angular range (2θ) of 3.8–30°. The values of MMT basal spacing d₀₀₁, expansion of clay gallery width W_cg, d‐spacing of polymer spherulite, crystallite size L and diffraction peak intensity I were determined for these nanocomposites. The values of structural parameters reveal that the linear chain PEO and PEG in the PVA blend based nanocomposites promote the amount of MMT intercalated structures, and these structures are found relatively higher for the (PVA–PEO)–x wt % MMT nanocomposites. It is observed that the presence of bulky ester‐side group in PVP backbone restricts its intercalation, whereas the adsorption behavior of PVP on the MMT nanosheets mainly results the MMT exfoliated structures in the (PVA–PVP)–x wt % MMT nanocomposites. The crystallinities of the PEO and PEG were found low due to their blending with PVA, which further decreased anomalously with the increase of MMT concentration in the nanocomposites. The decrease of polymer crystalline phase of these materials confirmed their suitability in preparation of novel solid polymer nanocomposite electrolytes. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40617.     

Preparation and properties of PET/PA6 copolymer/montmorillonite hybrid nanocomposite

From in situ polycondensation, a poly(ethylene terephthalate)/Polyamide 6 copolymer/montmorillonite nanocomposite was prepared, after the treatment of montmorillonite (MMT) with a water soluble polymer. The resulting nanocomposites were characterized by X‐ray diffraction (XRD), differential scanning calorimeter (DSC), nuclear magnetic resonance (NMR), dynamic mechanical analysis (DMA), and transmission electron microscopy (TEM). The results of DSC, ¹H NMR, and DMA proved that the nanocomposite synthesized was PET/PA6 copolymer/MMT nanocomposite, not the PET/PA6 blend/MMT nanocomposite. The results of XRD and TEM proved that the dispersion of MMT was improved observably after the introduction of PA6 molecular chain into PET. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2512–2517, 2006     

Poly(methyl methacrylate)/clay nanocomposites by photoinitiated free radical polymerization using intercalated monomer

A series of poly(methyl methacrylate)/montmorillonite (PMMA/MMT) nanocomposite were prepared by successfully dispersing the inorganic nanolayers of MMT clay in an organic PMMA matrix via in situ photoinitiated free radical polymerization. Methyl methacrylate monomer was first intercalated into the interlayer regions of organophilic clay hosts by “click” chemistry followed by a typical photoinitiated free radical polymerization. The intercalated monomer was characterized by FT-IR spectroscopy, elemental analysis and thermogravimetric analysis methods. The intercalation ability of the modified monomer and exfoliated nanocomposite structure were confirmed by X-ray diffraction spectroscopy (XRD), transmission electron microscopy (TEM) and atomic force microscopy (AFM). Thermal stability of PMMA/MMT nanocomposites was also studied by both differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA).     

The Nucleating Effect of Montmorillonite on Crystallization of PET/Montmorillonite Nanocomposite

Poly(ethylene terephthalate) (PET)/montmorillonite (MMT) nanocomposites were prepared by solution intercalation method. The clay was organo-modified with intercalation agent of cetyltrimetylammonium chloride (CMC). XRD showed that the layers of MMT were intercalated by CMC. Four nanocomposites with organoclay contents of 1, 5, 10, and 15 wt% were prepared by solution blending. XRD showed that the interlayer spacing of organoclay in the nanocomposites depends on the amount of organoclay. The nucleating effect of organoclay is investigated using differential scanning calorimetry (DSC) analysis. Clay behaves as a nucleating agent and enhances the crystallization rate of PET. Maximum enhancement in crystallization rate for the nanocomposites was observed in blends containing ca. 10 wt% of clay in the range of 1–15 wt%. According to transmission electron microscopy (TEM), the organoclay particle was highly dispersed in the PET matrix without a large agglomeration of particles for low organoclay content (5 wt%). Agglomerated structure did form in the PET matrix at 15 wt% organoclay content.     

聚乙烯醇/蒙脱石纳米复合材料的结构与性能

通过溶液插层 流延成膜法,以聚乙烯醇和钠质蒙脱石为原料,制备出了不同蒙脱石含量的聚乙烯醇/蒙脱石纳米复合材料薄膜。用X射线衍射(XRD)、扫描电子显微镜(SEM)、热重分析(TGA)和力学性能测试对复合材料的结构和性能进行了表征。结果表明,聚乙烯醇分子成功进入蒙脱石的层间,实现了在纳米尺度上的复合;蒙脱石含量高于7 5wt%形成插层型的纳米复合材料,低于7 5wt%形成剥离型的纳米复合材料;在SEM图片上还观察到了纳米复合材料的微观结构。纳米复合材料的热稳定性、拉伸强度和直角撕裂强度均比纯聚乙烯醇有很大提高。     

Colorless polyimide nanocomposite films with pristine clay: Thermal behavior,mechanical property,morphology, and optical transparency

Polyimide (PI)/clay hybrids were synthesized using the in situ solution intercalation method via poly(amic acid). The Na ion‐exchanged clays Na⁺‐saponite (SPT), Na⁺‐mica (Mica), and Na⁺‐montmorillonite (MMT) were used for the intercalation of PI polymer chains. Our dispersion results show that pristine SPT is more easily dispersed in a PI matrix than MMT or Mica. PI nanocomposites were prepared with various SPT contents to examine the variations with SPT content in the range 0–1 wt% of the thermomechanical properties, morphology, and optical transparency of the nanocomposites. The PI films have excellent optical transparencies, and are almost colorless. However, the optical transparency of the PI hybrid films decreases slightly with increases in the clay content. We also examined the relationship between the properties and clay content of the PI hybrid films using wide‐angle X‐ray diffraction (XRD) measurements, electronic microscopy (SEM and TEM), and universal tensile machine (UTM). The color intensities of the PI films were evaluated with a spectrophotometer. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Nonisothermal crystallization kinetics of poly(butylene terephthalate)/montmorillonite nanocomposites

The melt intercalation method was employed to prepare poly(butylene terephthalate) (PBT)/montmorillonite (MMT) nanocomposites, and the microstructures were characterized with X‐ray diffraction and transmission electron microscopy. Then, the nonisothermal crystallization behavior of the nanocomposites was studied with differential scanning calorimetry (DSC). The DSC results showed that the exothermic peaks for the nanocomposites distinctly shifted to lower temperatures at various cooling rates in comparison with that for pure PBT, and with increasing MMT content, the peak crystallization temperature of the PBT/MMT hybrids declined gradually. The nonisothermal crystallization kinetics were analyzed by the Avrami, Jeziorny, Ozawa, and Mo methods on the basis of the DSC data. The results revealed that very small amounts of clay (1 wt %) could accelerate the crystallization process, whereas higher clay loadings reduced the rate of crystallization. In addition, the activation energy for the transport of the macromolecular segments to the growing surface was determined by the Kissinger method. The results clearly indicated that the hybrids with small amounts of clay presented lower activation energy than PBT, whereas those with higher clay loadings showed higher activation energy. The MMT content and the crystallization conditions as well as the nature of the matrix itself affected the crystallization behavior of the hybrids. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3257–3265, 2006     

Preparation and characterization of poly(butylene terephthalate) nanocomposites with various organoclays

Layered‐silicate‐based polymer–clay nanocomposite materials were prepared depending on the surface modification of montmorillonite (MMT). Nanocomposites consisting of poly(butylene terephthalate) (PBT) as a matrix and dispersed inorganic clay modified with cetyl pyridinium chloride (CPC), benzyl dimethyl N‐hexadecyl ammonium chloride, and hexadecyl trimethyl ammonium bromide by direct melt intercalation were studied. The organoclay loading was varied from 1 to 5 wt %. The organoclays were characterized with X‐ray diffraction (XRD) to compute the crystallographic spacing and with thermogravimetric analysis to study the thermal stability. Detailed investigations of the mechanical and thermal properties as well as a dispersion study by XRD of the PBT/clay nanocomposites were conducted. X‐ray scattering showed that the layers of organoclay were intercalated with intercalating agents. According to the results of a differential scanning calorimetry analysis, clay acted as a nucleating agent, affecting the crystallization. The PBT nanocomposites containing clay treated with CPC showed good mechanical properties because of intercalation into the polymer matrix. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Intercalated clay structures and amorphous behavior of solution cast and melt pressed poly(ethylene oxide)–clay nanocomposites

The polymer nanocomposite (PNC) films consisted of poly(ethylene oxide) (PEO) and sodium cations montmorillonite (MMT) clay were prepared by aqueous solution casting and direct melt press compounding techniques, whereas the films of PEO with trimethyl octadecyl ammonium cations organo‐modified montmorillonite (OMMT) clay were formed by melt pressed technique. The clay concentrations in the nanocomposites used are 1, 2, 3, 5, 10, and 20 wt % of the PEO weight. The X‐ray diffraction patterns of these nanocomposites were measured in the angular range (2θ) of 3.8–30°. The values of basal spacing d₀₀₁ of MMT/OMMT, clay gallery width W_cg, d‐spacings of PEO crystal reflections d₁₂₀ and d₁₁₂, and their corresponding crystallite size L, and the peaks intensity I (counts) were determined for these nanocomposites. Results reveal that the nanocomposites have intercalated clay structures and the amount of intercalation increases with the increase of clay concentration. As compared to melt pressed PEO–MMT nanocomposites, the amount of clay intercalation is higher in aqueous solution cast nanocomposites. At 20 wt % MMT dispersion in PEO matrix, the solution cast PEO–MMT nanocomposite almost changes into amorphous phase. The melt press compounded PEO–OMMT films show more intercalation as compared to the PEO–MMT nanocomposites prepared by same technique. In melt pressed nanocomposites, the PEO crystalline phase significantly reduces when clay concentration exceeds 3 wt %, which is evidenced by the decrease in relative intensity of PEO principal crystalline peaks. The effect of interactions between the functional group (ethylene oxide) of PEO and layered sheets of clay on both the main crystalline peaks of PEO was separately analyzed using their XRD parameters in relation to structural conformations of these nanocomposites. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39898.     

Polystyrene nanocomposite materials by in situ polymerization into montmorillonite–vinyl monomer interlayers

A different series of new polystyrene–clay nanocomposites have been prepared by grafting polymerization of styrene with vinyl‐montmorillonite (MMT) clay. The synthesis was achieved through two steps. The first step is the modification of clay with the vinyl monomers, such as N,N‐dimethyl‐n‐octadecyl‐4‐vinylbenzyl‐ammonium chloride, n‐octadecyl‐4‐vinylbenzyl‐ammonium chloride, triphenyl‐4‐vinylbenzyl‐phosphonium chloride, and tri‐n‐butyl‐4‐vinylbenzyl‐phosphonium chloride. The second step is the polymerization of styrene with different ratios of vinyl‐MMT clay. The materials produced were characterized by different physical and chemical methods: (1) IR spectra, confirming the intercalation of the vinyl‐cation within the clay interlayers; (2) thermogravimetric analysis (TGA), showing higher thermal stability for PS–nanocomposites than polystyrene (PS) and higher thermal stability of nanocomposites with of phosphonium moieties than nanocomposites with ammonium moieties; (3) swelling measurements in different organic solvents, showing that the swelling degree in hydrophobic solvents increases as the clay ratio decreases; (4) X‐ray diffraction (XRD), illustrating that the nanocomposites were exfoliated at up to a 25 wt % of organoclay content; and (5) scanning electron microscopy (SEM), showing a complete dispersion of PS into clay galleries. Also, transmission electron microscopy (TEM) showed nanosize spherical particles of ～ 150–400 nm appearing in the images. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3739–3750, 2007     

Poly(vinyl alcohol) nanocomposite films: Thermooptical properties,morphology, and gas permeability

Poly(vinyl alcohol) (PVA)/saponite nanocomposites were prepared with various clay concentrations with the solution intercalation method. The intercalations of the polymer chains in the clay were examined with wide‐angle X‐ray diffraction and transmission electron microscopy. The variations of the dispersion, morphology, thermal properties, and gas permeability of the nanocomposites with clay concentrations in the range of 0–10 wt % were examined. Up to a 5 wt % clay loading, the clay particles were highly dispersed in the PVA matrix without any agglomeration of particles. However, some agglomerated structures formed in the polymer matrix above a 7 wt % clay concentration. The thermal stability of the hybrids increased linearly with increases in the clay loading up to 10 wt %. To measure the oxygen permeability and optical properties of the PVA hybrid films, the PVA hybrid solutions were coated onto both biaxially oriented polypropylene and poly(ethylene terephthalate) films, which were used as polymer substrates. The oxygen permeability values monotonically decreased with increases in the clay loading in the range of 0–10 wt %. The optical properties, such as the haze and gloss of the hybrid films when coated onto the matrix films, were nearly constant, that is, independent of the clay loading. These improvements arose because of the largely nanometer‐scale dispersion of the clay layers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 591–596, 2006     

Nanofibrillated cellulose,poly(vinyl alcohol), montmorillonite clay hybrid nanocomposites with superior barrier and thermomechanical properties

Nanocomposites of poly(vinyl alcohol) (PVA), nanofibrillated cellulose (NFC), and montmorillonite (MMT) clay were prepared via solvent casting. In addition to investigating the effect of clay loading, PVA matrices crosslinked with poly(acrylic acid) (PAA) were prepared and compared with linear (noncrosslinked) PVA nanocomposites. ¹³C NMR and infrared spectroscopy confirmed the presence of crosslinks. Scanning electron microscopy revealed effective NFC and MMT clay dispersion throughout the nanocomposites, while X‐ray diffraction highlighted the effectiveness of PAA to encourage clay dispersion. MMT clay provided a barrier against the diffusion of water and oxygen (molecules) through the nanocomposite films. Permeability and adsorption were further reduced by crosslinking, while oxygen barrier properties were remarkably enhanced at elevated relative humidities. Thermal stability of the PVA segments was strengthened by the presence of MMT clay and crosslinks. MMT clay–reinforced PVA and NFC within the films, increasing the Young's modulus, tensile strength, and glass transition temperature. Crosslinking further enhanced the thermomechanical properties by imparting physical restraints on polymer chain segments, providing elasticity, and ductility. The hybrid films were successfully reinforced at elevated humidities, with nanocomposites displaying enhanced storage moduli and near‐complete recovery. POLYM. COMPOS., 35:1117–1131, 2014. © 2013 Society of Plastics Engineers     

Synthesize and characterization of styrene‐N‐phenyl maleimide/montmorillonite nanocomposites prepared through emulsion polymerization

Composites of organomodified (OMMT) and pristine montmorillonite (MMT) intercalated by styrene‐N‐phenyl maleimide (PMI) copolymer were prepared by emulsion intercalative polymerization. X‐ray diffraction (XRD) and transmission electron microscopy results show that the dispersability of clay in the matrix was greatly improved by the incorporation of polar moiety PMI. The dispersability of OMMT in the matrix is better than MMT. XRD patterns of the extracted nanocomposites showed that d₀₀₁ of the clay are much larger than that of the original OMMT and MMT, which indicates that the interaction of copolymer with the clay layers was greatly improved by incorporation with polar monomer PMI. The thermal property of the composites was greatly improved by the intercalation with clay. The DSC results showed that the glass transition of the composites became inconspicuous, which indicated that the movement of the polymer segment was extremely confined by the clay layer. The consistency factor of the melts of the composites increased monotonically with a decreasing flow index showing stronger shear thinning property of the composites. The rheological activity energy of the composites decreased more than that of the pure copolymer. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1010–1015, 2005     

Preparation and characterization of carboxymethyl konjac glucomannan/sodium montmorillonite hybrid films

Carboxymethyl konjac glucomannan (CKGM)/ sodium montmorillonite (MMT) hybrid films of various compositions were prepared by casting from a polymer/silicate water suspension. The structure and properties of the hybrid films were investigated by wide angle X‐ray diffraction (WAXD), transmission electron microscopy (TEM), attenuated total reflection infrared spectroscopy (ATR‐IR), differential scanning calorimetry (DSC), and tensile tests. The results from WXRD and TEM indicated that an intercalated CKGM/MMT nanocomposite film was obtained by polymer solution intercalation. WXRD and DSC showed that the high‐T_m crystal phase was induced by the presence of lower MMT loading, but the T_m of the hybrid films became weak with the increase of MMT content due to the polymer confinement. The hybrid films showed higher thermal stability and mechanical properties than that of the neat polysaccharide due to the strong interaction between hydroxyl and carbonyl group of CKGM and the silicate layer of MMT. Furthermore, the degree of swelling of the hybrid films was investigated in acidic buffer solutions. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2954–2961, 2007     

聚乙烯醇/淀粉/MMT纳米复合材料的制备与性能研究

以蒙脱土（MMT）为增强填料,采用熔融加工的方法制备了聚乙烯醇（PVA）/淀粉/MMT纳米复合材料,通过X射线衍射、差示扫描量热法、扫描电子显微镜、热失重法以及力学性能测试等方法研究了MMT含量对复合材料结构与性能的影响。结果表明,在熔融加工过程中,淀粉、PVA分子破坏了MMT片层结构;MMT提高了复合材料中PVA组分结晶温度,阻碍PVA分子排入晶格,降低了复合材料熔融焓值及结晶度;MMT有效提高了材料的拉伸强度、弹性模量,同时降低了复合材料的吸水速率、平衡吸水率,提高了耐水性能。     

Preparation and Properties of Nanocomposites Derived from Aromatic Polyamide and Surface Functionalized Nanoclay

Nanocomposites were synthesized from polyamide and aminosilane functionalized montmorillonite through solution intercalation method. Polyamide resin was prepared by reacting a mixture of p-phenylenediamine and 4,4′-oxydianiline with isophthaloyl chloride (IPC) in N,N′-dimethyl acetamide (DMAc) under anhydrous conditions. The resulting chains were end capped with carbonyl chloride using slight excess of IPC near the end of reaction. 3-Aminopropyltriethoxysilane (APTS) was used for the surface modification of clay. Triethoxysilane groups of APTS promoted the reaction between silane and hydroxyl groups on the surface of clay. The compatibility between the two disparate phases was achieved through interaction of free amine groups of modified clay with carbonyl chloride of the matrix. Thin films obtained by evaporating the solvent were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Field emission scanning electron microscopy (FESEM), Transmission electron microscopy (TEM), Thermogravimetric analysis (TGA), Differential scanning calorimetry (DSC), and tensile measurements. XRD and TEM results revealed the formation of partially delaminated and intercalated clay platelets in the matrix. Mechanical data showed improvement in the tensile strength and moduli of the nanocomposites with clay loading up to 6 wt.%. The glass transition temperature increased up to 134°C for the nanocomposites containing 6 wt.% clay content and also the thermal stability augmented with increasing clay loading.     

Influence of clay content on the melting behavior and crystal structure of nonisothermal crystallized poly(L‐lactic acid)/nanocomposites

To study the effect of organophilic clay concentration on nonisothermal crystallization, poly(L ‐lactic acid) (PLLA)/montmorillonite (MMT) nanocomposites were prepared by mixing various amounts of commercial MMT (Cloisite^® 30B) and PLLA. The effect of MMT content on melting behavior and crystal structure of nonisothermal crystallized PLLA/MMT nanocomposites was investigated by differential scanning calorimetry (DSC), small‐angle X‐ray scattering, and wide‐angle X‐ray diffraction (XRD) analyses. The study was focused on the effect of the filler concentration on thermal and structural properties of the nonisothermally crystallized nanocomposite PLLA/MMT. The results obtained have shown that at filler loadings higher than 3 wt %, intercalation of the clay is observed. At lower clay concentrations (1–3 wt %), exfoliation predominates. DSC and XRD analysis data show that the crystallinity of PLLA/MMT composites increases drastically at high clay loadings (5–9 wt %). In these nanocomposites, PLLA crystallizes nonisothermally in an orthorhombic crystal structure, assigned to the α form of PLLA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012