Phase separation,cure kinetics,and morphology of epoxy/poly(vinyl acetate) blends

Epoxy based on diglycidyl ether of bisphenol A + 4,4′diaminodiphenylsulfone blended with poly(vinyl acetate) (PVAc) was investigated through differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA) and environmental scanning electron microscopy (ESEM). The influence of PVAc content on reaction induced phase separation, cure kinetics, morphology and dynamic‐mechanical properties of cured blends at 180°C is reported. Epoxy/PVAc blends (5, 10 and 15 wt % of PVAc content) are initially miscible but phase separate upon curing. DMTA α‐relaxations of cured blends agree with T_g results by DSC. The conversion‐time data revealed the cure reaction was slower in the blends than in the neat system, although the autocatalytic cure mechanism was not affected by the addition of PVAc. ESEM showed the cured epoxy/PVAc blends had different morphologies as a function of PVAc content: an inversion in morphology took place for blends containing 15 wt % PVAc. The changes in the blend morphology with PVAc content had a clear effect on the DMTA behavior. Inverted morphology blends had low storage modulus values and a high capability to dissipate energy at temperatures higher than the PVAc glass‐transition temperature, in contrast to the behavior of neat epoxy and blends with a low PVAc content. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1507–1516, 2007     

Effects of poly(vinyl acetate) and poly(methyl methacrylate) low-profile additives on the curing of unsaturated polyester resins. I. Curing kinetics by DSC and FTIR

The effects of two low-profile additives (LPA), poly(vinyl acetate) (PVAc) and poly(methyl methacrylate) (PMMA) on the curing kinetics during the cure of unsaturated polyester (UP) resins at 110°C were investigated by using a differential scanning calorimeter (DSC) and a Fourier transform infrared spectrometer (FTIR). The effects of temperature, molar ratio of styrene to polyester CC bonds, and LPA content on phase characteristics of the static ternary systems of styrene–UP–PVAc and styrene–UP–PMMA prior to reaction were presented. Depending on the molar ratio of styrene to polyester CC bonds, a small shoulder or a kinetic-controlled plateau in the initial portion of the DSC rate profile was observed for the LPA-containing sample. This was due to the facilitation of intramicrogel crosslinking reactions since LPA could enhance phase separation and thus favor the formation of clearly identified microgel particles. FTIR results showed that adding LPA could enhance the relative conversion of polyester CC bonds to styrene throughout the reaction. Finally, by use of a microgel-based kinetic model and static phase characteristics of styrene–UP–LPA systems at 25°C, the effects of LPA on reaction kinetics regarding intramicrogel and intermicrogel crosslinking reactions, relative conversion of styrene to polyester CC bonds, and the final conversio have been explained. © 1995 John Wiley & Sons, Inc.     

Effects of poly(vinyl acetate) and poly(methyl methacrylate) low-profile additives on the curing of unsaturated polyester resins. II. Morphological changes during cure

The effects of two low-profile additives (LPA), poly(vinyl acetate) (PVAc) and poly(methyl methacrylate) (PMMA), on the morphological changes during the cure of unsaturated polyester (UP) resins at 110°C were investigated by an approach of integrated reaction kinetics-morphology-phase separation measurements by using a differential scanning calorimeter (DSC), scanning electron microscopy (SEM), optical microscopy (OM), and a low-angle laser light-scattering appartus (LALLS). For the UP resins cured at 110°C, adding LPA could facilitate the phase separation between LPA and crosslinked UP phases early in the reaction, and discrete microgel particles were thus allowed to be identified throughout the reaction. Microvoids and microcracks responsible for the volume shrinkage control could also be observed evidently at the later stage of reaction under SEM. Depending on the types of LPA and the initial molar ratios of styrene to polyester C?C bonds, the morphological changes during the cure varied considerably. The progress of microstructure formation during reaction has been presented. Static ternary phase characteristics for the styrene–UP–LPA system at 25°C have also been employed to elucidate the resulting morphology during the cure in both the continuous and the dispersed phases. © 1995 John Wiley & Sons, Inc.     

Phase‐separation mechanism and corresponding final morphologies of thermoset blends based on unsaturated polyester and low‐molar‐weight saturated polyester

The final morphology of cured blends based on unsaturated polyester, styrene, and low‐molar‐weight saturated polyester as a low profile additive (LPA) was investigated with atomic force microscopy and scanning electron microscopy. The observed structure was compared to those obtained with widely used poly(vinyl acetate) (PVAc). On the surface and in the bulk, a network of particles, ranging in size from 50 to 60 nm, was observed with saturated polyester as an LPA. The influence of the molar weight and LPA content was investigated. To determine the mechanism of formation of such a morphology, in situ experiments were carried out to elucidate the phase‐separation mechanism. Small‐angle laser light scattering and small‐angle neutron scattering experiments were performed on ternary blends containing PVAc and saturated polyester, respectively. The first stage of spinodal decomposition was observed in both cases. Within our experimental conditions, gelation froze further evolution and led to a two‐phase cocontinuous structure that imposed the final morphology characteristics. In particular, the period and amplitude of the concentration fluctuations generated during the phase separation played essential roles. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1459–1472, 2005     

Phase separation of unsaturated polyester resin blended with poly(vinyl acetate)

The behavior of phase separation during the curing reaction of unsaturated polyester (UPE) resin in the presence of low profile additive, that is, poly(vinyl acetate) (PVAc), was studied by low-angle laser light scattering (LALS) and scanning electron microscopy (SEM). The experimental results revealed that the PVAc-rich phase was regularly dispersed in the cured styrene–UPE matrix for styrene–UPE resin blended with 5 wt % of PVAc. As the PVAc content was increased higher than 10 wt %, a cocontinuous PVAc and cured styrene–UPE phase was observed for the cured systems. The LALS observations were carried out in situ at a curing temperature of 100°C; thus, the effect of the rate of exothermic heat released from curing reaction on the morphology of curing system was investigated and reported in this work. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 2413–2428, 1999     

Effects of poly(methyl methacrylate)‐based low‐profile additives on the properties of cured unsaturated polyester resins. I. Miscibility,curing behavior,and glass‐transition temperatures

The effects of three series of self‐synthesized poly(methyl methacrylate) (PMMA)‐based low‐profile additives (LPAs), including PMMA, poly(methyl methacrylate‐co‐butyl acrylate), and poly(methyl methacrylate‐co‐butyl acrylate‐co‐maleic anhydride), with different chemical structures and MWs on the miscibility, cured‐sample morphology, curing kinetics, and glass‐transition temperatures for styrene (ST)/unsaturated polyester (UP) resin/LPA ternary systems were investigated by group contribution methods, scanning electron microscopy, differential scanning calorimetry (DSC), and dynamic mechanical analysis, respectively. Before curing at room temperature, the degree of phase separation for the ST/UP/LPA systems was generally explainable by the calculated polarity difference per unit volume between the UP resin and LPA. During curing at 110°C, the compatibility of the ST/UP/LPA systems, as revealed by cured‐sample morphology, was judged from the relative magnitude of the DSC peak reaction rate and the broadness of the peak. On the basis of Takayanagi's mechanical models, the effects of LPA on the final cure conversion and the glass‐transition temperature in the major continuous phase of ST‐crosslinked polyester for the ST/UP/LPA systems was also examined. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3369–3387, 2004     

Effects of reactive low‐profile additives on the volume shrinkage and internal pigmentability for low‐temperature cure of unsaturated polyester

The effects of reactive poly(vinyl acetate)‐block‐poly(methyl methacrylate) (PVAc‐b‐PMMA) and poly(vinyl acetate)‐block‐polystyrene (PVAc‐b‐PS) as low‐profile additives (LPA) on the volume shrinkage characteristics and internal pigmentability for low‐shrink unsaturated polyester resins (UP) during the cure at 30°C were investigated. These reactive LPAs, which contained peroxide linkages in their backbones, were synthesized by suspension polymerizations, using polymeric peroxides (PPO) as initiators. Depending on the LPA composition and molecular weight, the reactive LPA could lead to a reduction of cyclization reaction for UP resin during the cure, and would be favorable for the decrease of intrinsic polymerization shrinkage after the cure. The experimental results have been explained by an integrated approach of measurements for the static phase characteristics of the styrene (ST)/UP/LPA system, reaction kinetics, cured sample morphology, and microvoid formation by using differential scanning calorimetry (DSC), scanning electron microscopy (SEM), optical microscopy (OM), and image analysis. Based on the Takayanagi mechanical model, factors leading to both a good volume shrinkage control and acceptable internal pigmentability for the molded parts have been explored. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 967–979, 2006     

Control of shrinkage and residual styrene of unsaturated polyester resins cured at low temperatures: I. Effect of curing agents

In low temperature molding processes, control of resin shrinkage and residual monomer is an important concern. The presence of low profile additives (LPAs) can reduce the shrinkage of unsaturated polyester (UP)/styrene (St) resins under proper processing conditions but may increase the residual styrene content. A systematic study was carried out to investigate the effect of the initiator system and reaction temperature on sample morphology, final resin conversion, and resin shrinkage of UP resins with LPA. It was found that the final conversion of the resin system could be improved by using dual initiators. The effect is more obvious at low temperatures. Volume shrinkage measurements of the resin system initiated with dual initiators revealed that good LPA performance was achieved at low (e.g. 35 °C) and high (e.g. 100 °C) temperatures but not at intermediate ones. This can be explained by how temperature affects phase separation, reaction kinetics in the LPA-rich and UP-rich phases, micro-void formation, and thermal expansion.     

Effect of curing temperature on the morphology of unsaturated polyester resin blended with poly(vinyl acetate)

Phase separation of unsaturated polyester/styrene (UPE/styrene) resin blended with 5 and 10 wt% of poly(vinyl acetate) (PVAc) cured at various temperatures ranging from 75°C to 150°C was studied using low angle laser light scattering (LALS) and scanning electron microscopy (SEM). For UPE/styrene resin blended with 5 wt% PVAc cured at a temperature below 90°C, a discrete phase‐separated structure was observed. As curing temperature was raised above 90°C, SEM micrographs revealed that more and more cured UPE globules fused together with increasing curing temperature. The LALS intensity profile became broader with increasing curing temperature, indicating a less discrete phase‐separated structure at a higher curing temperature. As PVAc content was increased to 10 wt%, SEM micrographs revealed a co‐continuous phase‐separated structure. The LALS intensity decayed slowly from the center of the scattering pattern to a high scattering angle without the appearance of maximum scattering peak intensity. The morphology of the cured sample did not change too much with curing temperature for UPE/styrene resin blended with 10 wt% of PVAc.     

Effect of nanoclay on shrinkage control of low profile unsaturated polyester (UP) resin cured at room temperature

The addition of a small amount of nanoclay (1-3 wt%) can provide excellent volume shrinkage control of unsaturated polyester (UP)/styrene (St)/poly(vinyl acetate) (PVAc) systems cured at room temperature. PVAc serves as the low profile additive (LPA). In this study, both temperature-induced phase separation of the uncured resin mixture and transmission electron microscopy (TEM) of the cured sample revealed that nanoclay resided in the LPA-rich phase, leading to a higher reaction rate and earlier onset of micro-cracking in the LPA-rich phase or at the interface of the LPA-rich and UP-rich phases. Consequently, an earlier volume expansion during curing was observed in reactive dilatometry, resulting in better shrinkage control. On-line measurement of the composite thickness change during vacuum-infusion liquid composite molding [e.g. the Seemann Composite Resin Infusion Molding Process (SCRIMP)] further proved excellent volume shrinkage control of nanoclay filled systems, leading to a smoother composite surface.     

Wear and mechanical properties of reactive thermotropic liquid crystalline polymer/unsaturated polyester/glass fiber hybrid composites

To improve the performance of unsaturated polyester (UP) under cold‐heat alternate temperature, self‐synthesized reactive thermotropic liquid crystalline polymer (TLCP)‐methacryloyl copolymer (LCMC), UP, and glass fiber (GF) hybrid composites was prepared by molding technology. The apparent activation energy and crystal behavior analysis of LCMC/UP blends were investigated by Differential scanning calorimetry and X‐ray diffraction (XRD), respectively, the results showed that the addition of LCMC can reduce apparent activation energy and accelerate the curing reaction of UP, the XRD analysis indicated that the crystal phase of LCMC still exist in the blends after blending with UP. The effect of LCMC content on the properties of LCMC/UP/GF hybrid composites such as impact strength, bending strength, and ring‐on‐block wear were also investigated through static mechanical tests and wear tests. The mechanical properties of hybrid composites increased significantly because of the addition of LCMC. The wear tests showed that LCMC can improve the wear resistance of the UP/GF/LCMC hybrid composites even though the content of LCMC was at a relatively low level (5–7.5 wt %). This makes it possible to develop novel kind of UP‐based materials with good wear resistance for various applications. The Worn surface was observed by scanning electron microscopy (SEM) and the mechanism for the improvement is discussed in this paper. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3899–3906, 2007     

Effects of chemical structure of polyurethane‐based low‐profile additives on the miscibility,curing behavior,volume shrinkage,glass transition temperatures,and mechanical properties for styrene/unsaturated polyester/low‐profile additive ternary systems. I: Miscibility,curing behavior,and volume shrinkage

The effects of chemical structure and molecular weight of three series of thermoplastic polyurethane‐based (PU) low‐profile additives (LPA) on the miscibility of styrene (ST)/unsaturated polyester (UP) resin/LPA ternary systems prior to reaction were investigated by using the Flory‐Huggins theory and group contribution methods. The reaction kinetics during the cure at 110°C and the cured sample morphology were also studied by differential scanning calorimetry (DSC) and scanning electron microscopy (SEM), respectively. The phase‐separation characteristics of ST/UP/LPA systems during the cure, as revealed by the cured‐sample morphology, and the DSC reaction‐rate profile, could be generally predicted by the calculated upper critical solution temperature for the uncured ST/UP/LPA systems. Finally, based on the measurements for volume change and microvoid formation, volume shrinkage characteristics for the cured ST/UP/LPA systems have been explored. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 543–557, 2000     

Blends of styrene–butadiene–styrene triblock copolymer and isotactic polypropylene: morphology and thermomechanical properties

A set of blends of styrene–butadiene–styrene triblock copolymer (SBS) and isotactic polypropylene (i‐PP) in a composition range 0–100 % polypropylene by weight was prepared in a twin screw extruder. The morphology of the blends has been studied by transmission electron microscopy. The blends present phase separation. Dynamic mechanical measurements show an improvement of the mechanical properties of SBS when i‐PP is the dispersed phase. This reinforcing effect can be observed even at high temperatures when i‐PP is in the rubbery state. The mechanical properties of the blends have been interpreted using Takayanagi's block model. The melting and crystallization behaviour of the i‐PP in the blends has been studied by differential scanning calorimetry. The fractionated crystallization phenomenon has been observed in the blends where i‐PP forms the dispersed phase. The results are consistent with the morphology shown by the blends, in particular, with its phase inversion, which occurs at a composition near to 50% i‐PP. © 2000 Society of Chemical Industry     

Effects of chemical structure of polyurethane‐based low‐profile additives on the miscibility,curing behavior,volume shrinkage,glass transition temperatures,and mechanical properties for styrene/unsaturated polyester/low‐profile additive ternary systems. II: Glass transition temperatures and mechanical properties

The effects of three series of thermoplastic polyurethane‐based (PU) low‐profile additives (LPA) with different chemical structures and molecular weights on the glass transition temperatures and mechanical properties for thermoset polymer blends made from styrene (ST), unsaturated polyester (UP), and LPA have been investigated by an integrated approach of static phase characteristics‐cured sample morphology‐reaction conversion‐property measurements. The three series of PU used were made from 2,4‐tolylene di‐isocyanate (2,4‐TDI) and varied diols, namely polycaprolactone diol (PCL), poly(diethylene adipate) diol (PDEA), and poly(propylene glycol) diol (PPG), respectively, while the two UP resins employed were synthesized from maleic anhydride (MA) and 1,2‐propylene glycol (PG) with and without modification by phthalic anhydride (PA). Based on the Takayanagi mechanical models, factors that control the glass transition temperature in each phase region of cured samples, as identified by the method of thermally stimulated currents (TSC), and mechanical properties will be discussed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 558–568, 2000     

Mapping phases of poly(vinyl alcohol) and poly(vinyl acetate) blends by FTIR microspectroscopy and optical fluorescence microscopy

Fluorescence optical microscopy (FOM) of poly(vinyl alcohol) (PVA) and poly(vinyl acetate) (PVAc) blends in compositions 9/1, 1/1, and 1/9 (w/w) show that these blends present phase separation in the solid state. Each domain of the solid samples was identified by FOM as PVA-richer domains by green fluorescence of fluorescein and PVAc-richer domains by the blue fluorescence of anthracene. The dimensions, shapes, and distributions of these domains were dependent on the initial composition of the polymeric mixtures in the solution. Specific interactions between both homopolymers were studied using FTIR microspectroscopy, which allowed us to obtain spectra for both PVA-richer and PVAc-richer domains. These spectra demonstrated that partial miscibility could occur only for blends with a higher PVAc content and, in these cases, we observed interchain hydrogen-bonded carbonyl groups. Fluorescence microscopy of blends with this partial miscibility exhibited small interconnected domains produced by coalescence of droplets during the polymer phase separation process. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 645–655, 1998     

Micro-phase separation and crystallization behavior of amorphous oriented PLLA/PVAc blends during heat treatment under strain

Amorphous oriented poly(l-lactide) (PLLA)/poly(vinyl acetate) (PVAc) 50/50 films were prepared by uniaxial drawing of melt-mixed blends at 65 °C. The morphology development and crystal organization of the blends during heat treatment under strain were investigated using small angle X-ray scattering (SAXS) and wide-angle X-ray diffraction (WAXD). Equatorial scattering maxima in the SAXS patterns for samples annealed at 75 °C were observed before the appearance of crystal reflections. Further annealing of the samples at higher temperature induced two further discrete meridian scattering maxima. The observations indicated that homogenous oriented PLLA/PVAc film undergoes micro-phase separation first, followed by crystallization of PLLA in the PLLA-rich phase. The micro-phase separated PVAc nanodomains are aligned parallel to the stretching direction, whereas the crystallized PLLA lamellae are oriented perpendicular to the stretching direction (crystal c-axis along the stretching direction). Micro-phase separation was not observed when films were annealed at 120 °C, at which temperature the high crystallization rate of PLLA overwhelmed the micro-phase separation process.     

Cure reaction and phase separation behavior of cyanate ester‐cured epoxy/polyphenylene oxide blends

The cure reaction and phase separation mechanism of a cyanate ester‐cured epoxy and its blends with polyphenylene oxide (PPO) were studied. An autocatalytic mechanism was observed for the epoxy and its blends. The reaction rate of the blends was higher than that of the neat epoxy at initial stage; however, the reached conversion decreased with PPO content. FTIR analysis revealed that the cyanate functional group reactions were accelerated by adding PPO and indicated that several coreactions have occurred. This was caused by the reaction of cyanate ester with the PPO reactive chain ends. But at a later stage of cure, the reaction could not progress further due to diffusional limitation of PPO. To understand the relationship between the cure kinetics and phase separation of the blends, the morphology of the blends during cure was examined. When the homogeneous epoxy/PPO blends with low PPO content (10 phr) were cured isothermally, the blends were separated by nucleation and growth (NG) mechanism to form the PPO particle structure. But at high PPO content (30 phr), the phase separation took place via spinodal decomposition (SD). SD is favored near critical concentration and high cure rate system. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:1139–1145, 2006     

Effects of reactive low‐profile additives on the properties of cured unsaturated polyester resins. II. Glass‐transition temperature and mechanical properties

The effects of reactive poly(methyl methacrylate) (PMMA) and poly(vinyl acetate)‐block‐poly(methyl methacrylate) (PVAc‐b‐PMMA) as low‐profile additives (LPAs) on the glass‐transition temperature and mechanical properties of low‐shrink unsaturated polyester resin (UP) were investigated by an integrated approach of determining static phase characteristics, reaction kinetics, cured sample morphology, and property measurements. The factors that, according to Takayanagi mechanical models, control the glass‐transition temperature in each phase region of the cured samples, as identified by both the thermally stimulated currents method and dynamic mechanical analysis, and the mechanical properties are discussed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 867–878, 2006     

Phase behavior and properties of poly(methyl methacrylate)/poly(vinyl acetate) blends prepared via in situ polymerization

Polymer blends composed of poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) were prepared via radical-initiated polymerization of methyl methacrylate (MMA) in the presence of PVAc. Differential scanning calorimetry and dynamic mechanical analysis were employed to investigate the miscibility and phase behavior of the blends. The PMMA/PVAc blends of in situ polymerization were found to be phase separated and exhibited a two-phase structure, although some chain transferring reaction between the components occurred. The phase separation resulted from the solvent effect of MMA during the in situ polymerization, which was confirmed by the investigation of phase behavior based on solution cast blending. Solubility analysis of the polymerized blends indicated that some chain transferring reaction between the components occurred during the polymerization. An abrupt increase in gel content from 21.2 to 72.4 wt % was observed when the inclusion of PVAc increased from 30 to 40 wt %, and the gel component consisted of the component polymers as shown by infrared spectroscopy studies. The thermogravimetric analysis study indicated that the inclusion of a small amount of PVAc gives rise to a marked stabilization effect on the thermal stability. The PMMA/PVAc blends exhibited increased notched impact properties with the inclusion of 5 wt % PVAc. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 675–684, 1998     

Co-continuous and encapsulated three phase morphologies in uncompatibilized and reactively compatibilized polyamide 6/polypropylene/polystyrene ternary blends using two reactive precursors

Phase morphology development in ternary uncompatibilized and reactively compatibilized blends based on polyamide 6 (PA6), polypropylene (PP) and polystyrene (PS) has been investigated. Reactive compatibilization of the blends has been performed using two reactive precursors; maleic anhydride grafted polypropylene (PP-g-MA) and styrene maleic anhydride copolymer (SMA) for PA6/PP and PA6/PS pairs, respectively. For comparison purposes, uncompatibilized and reactively compatibilized PA6/PP and PA6/PS binary blends, were first investigated. All the blends were melt-blended using a co-rotating twin-screw extruder. The phase morphology investigated using scanning electron microscope (SEM) and selective solvent extraction tests revealed that PA6/PP/PS blends having a weight percent composition of 70/15/15 is constituted from polyamide 6 matrix in which are dispersed composite droplets of PP core encapsulated by PS phase. Whereas, a co-continuous three-phase morphology was formed in the blends having a composition of 40/30/30. This morphology has been significantly affected by the reactive compatibilization. In the compatibilized PA6/(PP/PP–MA)/(PS/SMA) blends, PA6 phase was no more continuous but gets finely dispersed in the PS continuous phase. The DSC measurements confirmed the dispersed character of the PA6 phase. Indeed, in the compatibilized PA6/(PP/PP–MA)/(PS/SMA) blends where the PA6 particle size was smaller than 1 μm, the bulk crystallization temperature of PA6 (188 °C) was completely suppressed and a new crystallization peak emerges at a lower temperature of 93 °C as a result of homogeneous nucleation of PA6.