Preparation of a PVA/HAP composite polymer membrane for a direct ethanol fuel cell (DEFC)

A novel PVA/Hydroxyapatite (HAP) composite polymer membrane was prepared by the direct blend process and solution casting method. The characteristic properties of the PVA/HAP composite polymer membranes were investigated using thermal gravimetric analysis (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM), micro-Raman spectroscopy and the AC impedance method. An alkaline direct ethanol fuel cell, consisting of an air cathode with MnO₂ carbon inks based on Ni-foam, an anode with PtRu black on Ni-foam, and the PVA/HAP composite polymer membrane, was assembled and investigated. It was found that the alkaline direct ethanol fuel cell comprising of a novel cheap PVA/HAP composite polymer membrane showed an improved electrochemical performance in ambient temperature and air. As a result, the maximum power density of the alkaline DEFC, using a PtRu anode based on Ni-foam (10.74 mW cm⁻²), is higher than that of DEFC using an E-TEK PtRu anode based on carbon (7.56 mW cm⁻²) in an 8M KOH + 2M C₂H₅OH solution at ambient temperature and air. These PVA/HAP composite polymer membranes are a potential candidate for alkaline DEFC applications.     

Fourier transform infrared study of polypyrrole–poly(vinyl alcohol) conducting polymer composite films: Evidence of film formation and characterization

The electrochemical preparation of polypyrrole (PPY)–poly(vinyl alcohol) (PVA) conducting polymer composite films on an indium–tin oxide glass electrode from an aqueous solution containing a pyrrole monomer, a p‐toluene sulfonate electrolyte, and a PVA insulating polymer is reported. The prepared PPY–PVA composite films were characterized by Fourier Transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), and conductivity measurements. The FTIR study showed that the composite of PPY and PVA formed through bond formation between PVA and the p‐toluene sulfonate dopant anion. The conductivity data of PPY–PVA showed that with increasing PVA concentration in the pyrrole solution, the conductivity of the prepared PPY–PVA film increased up to a certain level due to an increase in conjugation length, and later, it decreased with further increases in the PVA concentration in the solution due to a decrease in conjugation length. This was supported by the FTIR band intensity I₁₅₆₀/I₁₄₈₀. The TGA results show that the PPY–PVA polymer composite film was thermally more stable than the PPY film. A shielding effectiveness of 45.6 dB was exhibited by the PPY–PVA composite film in the microwave frequency range. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4107–4113, 2006     

Preferential mineralization of CaCO3 layers on polymer surfaces from CaCl2 and water‐soluble carbonate salt solutions supersaturated by poly(acrylic acid)

CaCO₃ was mineralized from solutions supersaturated only by poly(acrylic acid) (PAA), without bubbling any CO₂ gas in the solution. For example, a layer of CaCO₃ was built up on the surface of a chitosan membrane from a supersaturated aqueous solution containing CaCl₂, Na₂CO₃, and PAA. In this newly developed method, the PAA alone suppresses the precipitation of CaCO₃ from the bulk solution, and therefore, increases the supersaturated concentration. This concentration is estimated to be the same order as that attained in the method in which both CO₂ gas and PAA were used. At the same time, PAA supplies nucleation fields by forming a polymer complex with chitosan. The crystal system obtained was different from those obtained when using CO₂ gas. Self‐organization of aragonite crystallites led to the formation of uniform, concentric, or branching patterns in the surface‐domain structure. These patterns had morphologies similar to those discovered by other researchers, typically in the crystallization of ascorbic acid. Thicker layers of CaCO₃ could be formed on chitosan membranes, the surfaces of which had been converted to a polyelectrolyte complex (PEC) by exposure to PAA solution before the onset of mineralization. Under certain conditions, the CaCO₃ layer had a small spherical curvature, similar to a half‐lens, and generated Newton's ring pattern from the interference fringes of visible light. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91:3627–3634, 2004     

Structure,electrical and optical properties of (PVA/LiAsF6) polymer composite electrolyte films

In this work, Li⁺ ion conducting polymer composite electrolyte films (PECs) were prepared based on poly (vinyl alcohol) (PVA), lithium hexafluoro arsenate (LiAsF₆), and ceramic filler TiO₂ using solution cast technique. The XRD and FTIR spectra were used to determine the complexation of the PVA polymer with LiAsF₆ salt. The ionic conductivities of the (PVA + LiAsF₆) and (PVA + LiAsF₆ + TiO₂) films have been determined by the A.C. impedance measurements in the temperature range 320–440 K. The maximum conductivity was found to be 5.10 × 10^?4 S cm^?1 for PVA:LiAsF₆ (75:25) + 5 wt% TiO₂ polymer composite film at 320 K. The calculation of Li⁺ ion transference number was carried out by the combination of A.C. impedance and D.C. polarization methods and is found to be 0.52 for PVA:LiAsF₆ (75:25) + 5 wt% TiO₂ film. Optical properties such as direct energy gap, indirect energy gap, and optical absorption edge values were investigated in pure PVA and salt complexed PVA films from their optical absorption spectra in the wavelength range of 200–600 nm. The absorption edge was found at 5.76 eV for undoped film, while it is observed at 4.87 and 4.70 eV for 20 and 25 wt% LiAsF₆ doped films, respectively. The direct band gaps for these undoped and salt doped PVA films were found to be 5.40, 5.12, and 4.87 eV, respectively, whereas the indirect band gaps were determined as 4.75, 4.45, and 4.30 eV. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

ITO electrode modified by self-assembling multilayer film of polyoxometallate on poly(vinyl alcohol) nanofibers and its electrocatalytic behavior

Poly(vinyl alcohol) (PVA) nanofiber mats were collected on indium tin oxide (ITO) substrate by electrospinning method. A multilayer film composed of α-[P₂W₁₈O₆₂]⁶⁻ (abbr. P₂W₁₈), a polyoxometallate (POM) anion, and poly(diallymethylammonium chloride) (abbr. PDDA) was fabricated by layer-by-layer (LBL) self-assembly technique on the PVA/ITO electrode. The PDDA/P₂W₁₈ multilayer film could be unselectively or selectively deposited on the PVA/ITO electrode via changing the amount of PVA nanofibers on the ITO substrate. The scanning electron microscope (SEM) images showed that when the electrospun time was short the PDDA/P₂W₁₈ multilayer film was unselectively deposited on PVA nanofiber mats because the amount of PVA nanofibers was too little to cover most of the ITO substrate. However, when the electrospun time was long enough, the PDDA/P₂W₁₈ multilayer film was selectively deposited on PVA nanofiber mats because of the larger surface area and higher surface energy of PVA nanofibers in comparison with the flat ITO substrate. Growth process of the multilayer film was determined by cyclic voltammetry (CV). Electrocatalytic effects of the PDDA/P₂W₁₈ multilayer film unselectively and selectively deposited on the PVA/ITO electrode on NO₂⁻ were observed.     

Oxidative graft polymerization of aniline on the modified surface of polypropylene films

A novel method for preparing electrically conductive polypropylene‐graft‐polyacrylic acid/polyaniline (PP‐g‐PAA/PANI) composite films was developed. 1,4‐Phenylenediamine (PDA) was introduced on the surface of PP‐g‐PAA film, and then, chemical oxidative polymerization of aniline on PP‐g‐PAA/PDA film was carried out to prepare PP‐g‐PAA/PANI electrically conductive composite films. After each step of reaction, the PP film surface was characterized by attenuated total reflectance Fourier transform infrared spectroscopy. Static water contact angles of the PP, PP‐g‐PAA, and PP‐g‐PAA/PANI films were measured, and the results revealed that graft reactions took place as expected. The morphology of the PP‐g‐PAA film and the PP‐g‐PAA/PANI composite film were observed by atomic force microscopy. The conductivity and the thickness of the PP‐g‐PAA/PANI composite films with 1.5 wt % PANI were around 0.21 S/cm and 0.4 μm, respectively. The PANI on the PP‐g‐PAA/PANI film was reactivated and chain growing occurred to further improve the molecular weight of PANI. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2442–2450, 2007     

Preparation of PANI–PVA composite film with good conductivity and strong mechanical property

The polyaniline (PANI)–polyvinyl alcohol (PVA) conductive composite films [doped with hydrochloride (HCl), dodecylbenzene sulphonic acid and amino sulphonic acid (NH₂SO₃H) aqueous solution] were synthesised by ‘in situ’ polymerisation, and their conductivities were compared. Among these composite films, HCl–PANI–PVA composite film possessed the highest conductivity that reached 1360?S·m^??1 [w_(PVA)?=?40%]. Meanwhile, the effects of PVA content, HCl concentration, oxidant ammonium persulphate (APS) dosage, reaction time and film drying temperature on tensile strength of the HCl–PANI–PVA composite films were studied. The tensile strength of the film was improved greatly due to effective mixture of PANI and PVA. When the PVA content was 40%, C_(HCl)?=?1.0?mol·L^??1, reaction time was 4.0?h, n_(APS)/n_(aniline)?=?1.0 and film drying temperature was 80°C, and the tensile strength of the HCl–PANI–PVA composite film reached the maximum of 60.8?MPa. At the same time, the structure of composite materials was characterised and analysed through ultraviolet spectrum and SEM.     

Adsorption and adhesion of poly(vinyl alcohol) and poly(ammonium acrylate) as organic additives for wet mold processing of Al2O3

Adsorption and adhesion of polyvinyl alcohol (PVA) molecules on Al₂O₃ surfaces in pH 3–10 or 0–0.1 mass% poly(ammonium acrylate) (PAA) aqueous solution was examined using the AFM colloidal probe method. The PVA behavior on the solid surface was estimated using force curve measurements obtained using colloidal probe AFM. Extensions originating from the bridging of PVA between the solid surfaces were observed primarily at less than approximately 200 nm in the pH 3 aqueous solution. The extensions, which were observed at more than approximately 600 nm for pH 6 and 10 aqueous solutions, resulted from different conformations of the PVA molecules. In the PVA–PAA system, the number of extensions decreased by increasing the PAA content. This was not observed in a PAA aqueous solution of greater than 0.1 mass%, which indicates that PAA was adsorbed selectively onto the solid surface. The force curve showed that PAA was more effective than PVA.     

Application of FTIR spectroscopy for structural characterization of ternary poly(acrylic acid)–metal–poly(vinyl pyrrolidone) complexes

The FTIR spectroscopic technique was used in the study of ternary polymer–metal complexes containing two polyelectrolytes of opposite charge and metal ions. The structure of the ternary (PAA‐Fe³⁺‐PVP) complexes was examined by following the changes in their infrared spectra. It was found that the shapes of the absorption bands of the resultant compounds are influenced by the presence of Fe³⁺. According to this result it was suggested that two types of structure which differ in the composition are formed, one of which results from the coordination of Fe³⁺ with PAA‐PVP complex and the other is due to the formation of Fe³⁺ polycarboxylate. Comparison between the spectrum of PAA‐PVP complex and those of the compounds resulted from the reaction between the two opposite charged electrolytes, PAA and PVP and each of the divalent metal chlorides NiCl₂, CoCl₂, CuCl₂, and ZnCl₂) led to the conclusion that a reaction took place between the divalent transition metal chlorides and the extent of reaction depends on the nature of metal ions and PAA‐PVP complex. The FTIR spectra of the precipitate resulted from the mixtures of PAA‐PVP and Ni(NO₃)₂ or Sr(NO₃)₂ were investigated. It was noted that the addition of Ni(NO₃)₂ or Sr(NO₃)₂ to the mixture of the electrolytes of PAA and PVP provoked appreciable changes in the characteristic spectral features of the complex resulting from the interaction of the metal ions with the polymer–polymer complex. The FTIR spectra of the precipitate resulted from the reaction between CeCl₃, ErCl₃, and LaCl₃ were also investigated. It was concluded that a reaction took place between the rare earth metals and the PPC. This means that ternary polymer–metal–polymer complexes were formed. The extent of changes in the spectral features differs from metal to metal according to the nature of metal ions. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Biomimetic synthesis of calcium carbonate films on bioinspired polydopamine matrices

We combine the active surface of polydopamine (PDA) with the biomimetic mineralization of CaCO₃ to obtain the macroscopically continuous CaCO₃ films under mild conditions. In this approach, the organic matrices were adhesive PDA coatings, which were dip-coated on silicon wafers by the self-polymerization of dopamine in an alkaline aqueous solution (pH 8.5). The inorganic layers were CaCO₃ films, which were formed in a CaCl₂ solution in the presence of poly(acrylic acid) (PAA) via a CO₂ diffusion method. During the biomimetic mineralization, amorphous calcium carbonate (ACC) was formed on PDA matrices with the help of PAA, which, subsequently, was transformed into a flat continuous calcite film on the PDA matrices. As the mineralization time increased, a new layer of CaCO₃ crystals was formed over the calcite and, as a result, led to continuous CaCO₃ films with rough surfaces. The thicknesses of CaCO₃ films can be controlled by tuning the mineralization time. Our approach may provide a simple, yet efficient way for the preparation of macroscopically continuous organic–inorganic composite CaCO₃ films under mild conditions. Moreover, superhydrophobic surfaces can be successfully achieved via a hydrophobic modification of the rough CaCO₃ films, which make them suitable candidates for a variety of superhydrophobic applications, such as self-cleaning surfaces or anticorrosion, antiadhesive coatings.     

Pervaporation separation of binary organic-aqueous liquid mixtures using crosslinked poly(vinyl alcohol) membranes. IV. Methanol–water mixtures

The pervaporation separation of methanol–water (M/W) mixtures was carried out using crosslinked poly(vinyl alcohol) (PVA) membranes with the low molecular weight of poly(acrylic acid) (PAA) as the crossinking agent. The PVA/PAA ratio in the crosslinked membrane was 90/10, 85/15, and 80/20 by weight. The operating temperatures were 50, 60, and 70°C, and the compositions of methanol–water mixtures to be separated were 70/30, 80/20, 90/10, and 95/5 (M/W) solutions. In all cases, the PVA/PAA = 80/20 membrane showed the best results. For M/W = 90/10 solution, the separation factor, α_w/m = 465, and the permeation rate, 0.109 kg/m²h, at 70°C were obtained using the PVA/PAA = 80/20 menbrane. The permeation rate and the separation factor for M/W = 95/5 solution showed 0.033 kg/m²h and α_w/m = 2650, respectively, when PVA/PAA = 80/20 membrane was used. © 1996 John Wiley & Sons, Inc.     

Effect of additives in PEO/PAA/PMAA composite solid polymer electrolytes on the ionic conductivity and Li ion battery performance

Polyethylene oxide (PEO) based-solid polymer electrolytes were prepared with low weight polymers bearing carboxylic acid groups added onto the polymer backbone, and the variation of the conductivity and performance of the resulting Li ion battery system was examined. The composite solid polymer electrolytes (CSPEs) were composed of PEO, LiClO_4, PAA (polyacrylic acid), PMAA (polymethacrylic acid), and Al₂O₃. The addition of additives to the PEO matrix enhanced the ionic conductivities of the electrolyte. The composite electrolyte composed of PEO:LiClO₄:PAA/PMAA/Li_0.3 exhibited a low polarization resistance of 881.5 ohms in its impedance spectra, while the PEO:LiClO₄ film showed a high value of 4,592 ohms. The highest ionic conductivity of 9.87 × 10⁻⁴ S cm⁻¹ was attained for the electrolyte composed of PEO:LiClO₄:PAA/PMAA/Li_0.3 at 20 °C. The cyclic voltammogram of Li⁺ recorded for the cell consisting of the PEO:LiClO₄:PAA/PMAA/Li_0.3:Al₂O₃ composite electrolyte exhibited the same diffusion process as that obtained with an ultra-microelectrode. Based on this electrolyte, the applicability of the solid polymer electrolytes to lithium batteries was examined for an Li/SPE/LiNi_0.5Co_0.5O₂ cell.     

Preparation and swelling properties of semi‐IPN hydrogels based on chitosan‐g‐poly(acrylic acid) and phosphorylated polyvinyl alcohol

The phosphorylated poly(vinyl alcohol) (P‐PVA) samples with various substitution degrees were prepared through the esterification reaction of PVA and phosphoric acid. By using chitosan (CTS), acrylic acid (AA) and P‐PVA as raw materials, ammonium persulphate (APS) as an initiator and N,N‐methylenebisacrylamide as a crosslinker, the CTS‐g‐PAA/P‐PVA semi‐interpenetrated polymer network (IPN) ssuperabsorbent hydrogel was prepared in aqueous solution by the graft copolymerization of CTS and AA and followed by an interpenetrating and crosslinking of P‐PVA chains. The hydrogel was characterized by Fourier transform infrared (FTIR), scanning electron microscopy (SEM), and differential scanning calorimetry (DSC) techniques, and the influence of reaction variables, such as the substitution degree and content of P‐PVA on water absorbency were also investigated. FTIR and DSC results confirmed that PAA had been grafted onto CTS backbone and revealed the existence of phase separation and the formation of semi‐IPN network structure. SEM observations indicate that the incorporation of P‐PVA induced highly porous structure, and P‐PVA was uniformly dispersed in the polymeric network. Swelling results showed that CTS‐g‐PAA/P‐PVA semi‐IPN superabsorbent hydrogel exhibited improved swelling capability (421 g·g^?1 in distilled water and 55 g·g^?1 in 0.9 wt % NaCl solution) and swelling rate compared with CTS‐g‐PAA/PVA hydrogel (301 g·g^?1 in distilled water and 47 g·g^?1 in 0.9 wt % NaCl solution) due to the phosphorylation of PVA. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Bending of ionic polymer gel caused by swelling under sinusoidally varying electric fields

Deformation of poly(vinyl alcohol)–poly(sodium acrylate) composite hydrogel (PVA–PAA gel) under sinusoidally varying electric fields was studied in electrolyte solutions. The PVA–PAA gel was prepared by repeatedly freezing and thawing a mixed solution of PVA and polyacrylic acid. A cyclic bending–straightening motion of the PVA–PAA gel rods of about 1 mm in diameter have been observed in Na₂CO₃ aqueous solutions under the fields. The PVA–PAA gel had a response time of less than several hundreds milliseconds. The bending has also been observed in organic solvents containing an electrolyte when the organic solvent is electrolyzed. It was found that the motion of the gel under electric fields of less than 1 Hz occurred mainly through swelling due to the change of the osmotic pressure based upon the difference of the ion concentration. However, it has not been determined whether the motion at higher frequencies is caused by the osmotic effect. © 1993 John Wiley & Sons, Inc.     

Effect of the type of polymer functional groups on the structure of its film formed on the alumina surface – Suspension stability

The effects of polymer functional group and solution pH on stability of colloidal Al₂O₃ water suspension were studied. Both the nonionic polymers: polyethylene glycol (PEG), polyethylene oxide (PEO) and the ionic ones: polyacrylic acid (PAA), polyacrylamide (PAM), polyvinyl alcohol (PVA) were used in the experiments. The following methods were applied: turbidimetry (stability measurements), spectrophotometry (determination of polymer adsorption), viscosimetry (thickness of polymer adsorption layer), potentiometric titration (solid surface charge density) and microelectrophoresis (potential zeta). It was shown that anionic polyacrylic acid is both the most effective stabilizer (at pH 9) and flocculant (at pH 3) of the alumina suspension. Its carboxyl groups have the greatest affinity for the surface active sites (the largest adsorption) of all functional groups present in the other examined polymers. The latter, i.e. hydroxyl (PEG, PEO, and PVA) and acetate (PVA) show a much lower affinity for the Al₂O₃ surface (negligible adsorption) and minimally affect the stability of the alumina-solution system.     

聚乙烯醇/淀粉/凤仙透骨草提取物复合膜制备及性能

以聚乙烯醇(Polyvinyl alcohol,PVA)、淀粉(Starch,ST)为原料,凤仙透骨草提取物(Impatiens balsamina extract,IBE)为抗菌剂,通过共混法制备抗菌复合膜,通过FTIR、XRD、SEM和热重分析对复合膜的形貌和结构进行表征及对力学、光学、阻隔、抑菌等性能测试分析。结果表明,IBE与PVA/ST基膜复合良好,制备的PVA/ST/IBE抗菌复合膜对大肠杆菌、白色葡萄球菌和枯草杆菌具有良好的抑菌作用,抑菌性能随着IBE含量的增加而逐渐提高；同时具有良好的力学强度,IBE添加量为12.5 mL的复合膜拉伸强度达到22.97±0.68 MPa,断裂伸长率相比PVA/ST基膜提升了79.22%；透明度有所下降,透光率下降了11.90%；氧气阻隔性能良好,氧气透过系数为1.771±0.196×10_-12 ^cm₃^.cm/(cm₂^.s.Pa),在环保包装、食品保鲜等领域具有广阔的应用前景。     

Characteristics and sensing behavior of electrochemically codeposited polypyrrole–poly(vinyl alcohol) thin film exposed to ethanol vapors

Polypyrrole–poly(vinyl alcohol) (PPy–PVA) composite films were prepared electrochemically by means of codeposition at a constant potential. Their sensing behaviors to various ethanol-vapor concentrations were investigated. Increasing the molar fraction of PVA up to PPy_0.964PVA_0.036 showed an increase of the sensitivity of the composite sensors. However, the sensitivity decreased if further PVA was incorporated. The ethanol-sensing behaviors were also largely dependent upon the electropolymerization charge, ranging from 50 to 200 mC in this investigation. Higher sensitivity was measured from the composite film prepared with a lower electrical charge. For example, a sensitivity of 7.70 mΩ mg⁻¹ L, about 3.3 times the sensitivity of the pristine PPy sensor, was measured by the PPy_0.964PVA_0.036 composite film prepared at 50 mC. However, incorporating PVA into the conducting polymer was at the sacrifice of the response speed as well as the stability of the composite as it was under continuous exposure to ethanol vapor. An adsorption model based on the Langmuir isotherm was used to interpret the sensing behaviors and the equation derived from this model correlated well with the measured sensitivities. The sensing parameters including the adsorption equilibrium constant, K_m, and the resistance change caused by a pseudomonolayer, [m(r₁ − r₂)]/n, were determined and found to decrease with increasing polymerization charge. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 2079–2087, 1999     

Ionic conduction of novel polymer composite films based on partially phosphorylated poly(vinyl alcohol)

New ion-conducting polymer composite films have been prepared, and their ionic conducting properties have been investigated. The polymer composite films are fabricated from partially phosphorylated poly(vinyl alcohol) with tetramethylammonium salt (P-PVA·Me₄N⁺) and poly(acrylic acid) (PAA) or poly(ethylene glycol) (PEG). For P-PVA·Me₄N⁺/PEG composite films, the ionic conductivity and carrier density sharply increased, and carrier mobility sharply decreased around [PEG]/[PO₃]_P-PVA of 2. The ionic conductivity is dominated by both carrier density and carrier mobility at [PEG]/[PO₃]_P-PVA<2 and only by carrier density at [PEG]/[PO₃]_P-PVA>2. This is attributed to the fact that the ionic conduction in P-PVA·Me₄N⁺/PEG composite films occurred through the PEG-Me₄N⁺ complex which was independent of the carrier mobility. On the other hand, the ionic conductivity in P-PVA·Me₄N⁺/PAA composite films showed a bell-shaped dependence on the PAA contents with a maximum value at [CO₂H]_PAA/[OH]_P-PVA=1. FTIR spectrum measurements demonstrated that part of the carboxylic acid residues was dissociated in the composite films. This fact implied that the ionic conduction was mediated by PAA at the low PAA content. At high PAA content, however, an excess of the carboxylic acid residues formed trapping sites for the Me₄N⁺ ion, leading to a decrease in the ionic conductivity. Furthermore, we proposed a unique mechanism of the ionic conduction.     

Swelling behavior of hydroxyapatite‐filled chitosan–poly(acrylic acid) polyelectrolyte complexes

A family of hydroxyapatite (HAP)‐filled chitosan (CHI)–poly(acrylic acid) (PAA) polyelectrolyte complexes was prepared for the development of a degradable biocompatible organic matrix with nascent HAP that will degrade in vivo over a period of time. The effects of complexation on the degradation profile of the composites as well as the interaction between the CHI–PAA matrix and HAP in the composite system were evaluated by studying the swelling behavior of these composites in phosphate‐buffered saline (PBS) by varying their CHI–PAA ratio and HAP content. All composite systems showed a general trend of three stages of swelling with the variation in the degree of equilibrium swelling. The percentage weight gain initially decreased in a linear way with increases in the HAP weight percentages, leading to a first equilibrium swelling, represented by the plateau; further increased to a greater extent; and finally stabilized. The CHI/PAA/HAP composites were stable in PBS up to a period of more than 45 days whereas the 50/50 CHI/PAA control sample showed a single equilibrium attained after a period of 288 h. Further exposure of the specimen to the medium led to its disintegration. It was also observed that, even though CHI and PAA were capable of binding HAP, because of the lack of efficient binding, the integrity of the CHI–HAP and PAA–HAP composites were lost within 48 h. The 50/50/80 CHI/PAA/HAP composition showed the minimum amount of swelling in the series. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4716–4722, 2006     

Working mechanism of poly(vinyl alcohol) cement fluid loss additive

The working mechanism of poly(vinyl alcohol) (PVA, M_w ～ 200,000 g mol^?1), a fluid loss control additive (FLA) applied in oil well cementing, was investigated. First, characteristic properties of PVA such as solubility and particle size in cold and hot water, minimum film forming temperature, adsorption on cement, viscosity of cement pore solution and static filtration properties of cement slurries treated with PVA were determined. It was found that the working mechanism of PVA relies on hydrated, but water‐insoluble PVA particles (d₅₀ ～ 2.4 μm). During cement slurry filtration, they coalesce into a polymer film. This film effectively plugs the pores of the cement filter cake. The sample studied here becomes water‐soluble at temperatures > 40°C (d₅₀ decreases to ～50 nm) and looses its effectiveness. Addition of highly anionic dispersants such as ß‐naphthalenesulfonate formaldehyde (BNS) or acetone formaldehyde sulfite (AFS) polycondensate extends the temperature range at which PVA works from 40°C to ～60°C. This effect is ascribed to lower solubility of PVA in the presence of these dispersants. The study reveals that decreased performance of PVA caused by higher temperatures is not the result of thermal degradation of the polymer, but is owed to its increasing water‐solubility. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010