Study of grafting propylene–ethylene block copolymer

The article describes the mechanical properties of a propylene–ethylene block copolymer (Co-PP) used as a matrix with acrylic acid (AA) and strengthened with glass fiber. Isotactic polypropylene (i-PP) is also used as a matrix to compare with the results obtained from the Co-PP grafting. Experimental results indicate that AA grafting improves the interfacial adhesion between the matrices and glass fiber. AA grafting also enhances the mechanical properties of glass fiber-reinforced polypropylene (FRPP). A quantitative titration is performed to analyze the grafting ratio and grafting efficiency. In addition, the specimens are injection-molded to investigate the mechanical properties and morphologies. In addition, the effects on the matrix structure, attributed to the grafting and blending of the glass fiber, are also investigated. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 977–988, 1998     

Structure and deformation of an elastomeric propylene–ethylene copolymer

The elastic behavior of a propylene–ethylene copolymer was investigated. An initial “conditioning” tensile extension up to 800% strain resulted in an elastomer with low initial modulus, strong strain hardening, and complete recovery over many cycles. Structural changes that occurred in the low crystallinity propylene–ethylene copolymer during conditioning, and that subsequently imparted elastomeric properties to the conditioned material, were investigated. Thermal analysis, wide and small angle X‐ray diffraction, and atomic force microscopy measurements were performed at various strains during the conditioning process. Conditioning transformed crystalline lamellae into shish‐kebab fibers by melting and recrystallization. The fibers, accounting for only 5% of the bulk, were interconnected by a matrix of entangled, amorphous chains that constituted the remaining 95%. It was proposed that the shish‐kebab fibers acted as a scaffold to anchor the amorphous rubbery network. Entanglements of the amorphous chain segments acted as network junctions and provided the elastic response. The stress–strain response of materials conditioned to 400% strain or more was described by the classical rubber theory with strain hardening. The extracted value of M_c, the molecular weight between network junctions, was intermediate between the entanglement molecular weights of polypropylene and polyethylene. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 489–499, 2007     

Morphology of pyrolyzed polystyrene–isoprene–styrene and polystyrene–butadiene–styrene block copolymers

The surface morphology of thermooxidative‐degraded polystyrene–isoprene–styrene (SIS) and polystyrene–butadiene–styrene (SBS) thermoplastic block copolymers were studied by scanning electron microscopy. Surface changes caused by heating the samples in a pyrolizer for 15 and 30 min were presented in different micrographs. The morphological changes occurring due to the formation of polar groups and their crossing linking during the thermooxidative degradation are discussed. Morphological study of these thermally degraded polymer samples show very good correlation with the thermodegradation results. The rate of thermodegradation is fast in case of SBS compared with SIS block copolymer. ©2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Morphology of pyrolysed polystyrene–isoprene–styrene and polystyrene–butadiene–styrene block copolymers

The surface morphology of thermooxidative degraded polystyrene–isoprene–styrene (SIS) and polystyrene–butadiene–styrene (SBS) thermoplastic block copolymers was studied by scanning electron microscopy. Surface changes caused by heating the samples in a pyrolyzer for 15 and 30 min were presented in different micrographs. The morphological changes occurring due to the formation of polar groups and their crosslinking during the thermooxidative degradation are discussed. Morphological study of these thermally degraded polymer samples shows very good correlation with the thermodegradation results. The rate of thermodegradation is fast in case of SBS when compared with SIS block copolymer. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 2549–2553, 2006     

Comparing elastomeric behavior of block and random ethylene–octene copolymers

This work compared the elastomeric properties of two low‐crystallinity ethylene–octene copolymers. One was a block copolymer with lamellar crystals and the other was a random copolymer with fringed micellar crystals. The comparison of the stress–strain behavior at 23°C revealed that the initial elastic modulus and the yield stress depended only on the crystallinity of the copolymer. When the temperature was raised above 23°C, melting of the fringed micellar crystals of the random copolymer caused a rapid decrease in the modulus. Some decrease in the modulus of the block copolymer over the same temperature range was attributed to the crystalline α‐relaxation. Both polymers exhibited strain‐hardening, ultimate fracture at high strains, and high recovery after fracture. However, in the block copolymer, the onset of strain‐hardening and the ultimate fracture occurred at higher strains. The block copolymer also showed higher recovery from high strains. The initial stretching resulted in a permanent change in the stress–strain curve. It was suggested that following the onset of crystal slippage at the yield, the crystals underwent permanent structural changes through the course of the strain‐hardening region. The transformation of the fringed micellar crystals occurred at lower strains than the transformation of the lamellar crystals. The extent of the structural transformation was described by the crosslink density and the strain‐hardening coefficient extracted from elasticity theory. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Crystallinity and amorphous segmental properties in random propylene–ethylene copolymers: NMR correlation

We present a characterization of the state of semi-crystallization of random propylene–ethylene copolymers, observing the transverse relaxation of protons attached to the chains. The degree of crystallinity was determined step by step, from NMR, during the progressive annealing of the copolymers, quenched at room temperature from the melt. The ethylene content varied over the range 0–4.7 (w/w). It is shown that the empirical temperature dependence of the degree of crystallinity, as detected by NMR, obeys a single curve; this curve is translated along the temperature axis in accordance with the melting point depression when the ethylene content varies. The degree of crystallinity is primarily a function of the undercooling, whatever the ethylene content. Considering any state of semi-crystallization, a strong correlation between the degree of crystallinity and the relaxation rate of the protons attached to amorphous segments is established; the NMR sensitivity to crystallinity is considerably enhanced when detected by amorphous properties. © 1999 Society of Chemical Industry     

X-ray diffraction studies of ABA propylene–ethylene block copolymers

ABA triblock copolymers of propylene and ethylene, where the central block is a random copolymer of ethylene and propylene and the A blocks are either isotactic polypropylene or polyethylene, are described. Structural changes induced by stretching at room and elevated temperatures are reported. WAXS was used to monitor these changes. The results indicate theat block copolymers were synthesized and that different combinations of mechanical properties may be obtained by varying the type and length of the A blocks and adjusting the monomer ratio in the random B block.     

Synthesis of PP–LCP graft copolymers and their compatibilizing activity for PP/LCP blends

The aim of this work was the synthesis of new graft copolymers consisting of polypropylene (PP) backbones and liquid crystalline polymer (LCP) branches, to be used as compatibilizing agents for PP/LCP blends. The PP-g-LCP copolymers have been prepared by polycondensation of the monomers of a semiflexible liquid crystalline polyester (SBH 1 : 1 : 2), that is, sebacic acid (S), 4,4′-dihydroxybiphenyl (B), and 4-hydroxybenzoic acid (H) in the mole ratio of 1 : 1 : 2, carried out in the presence of appropriate amounts of a commercial acrylic-acid-functionalized polypropylene (PPAA). The polycondensation products, referred to as COPP50 and COPP70, having a calculated PPAA concentration of 50 and 70 wt %, respectively, have been fractionated with boiling toluene and xylene, and the soluble and insoluble fractions have been characterized by Fourier transform infrared and nuclear magnetic resonance spectroscopy, scanning electron microscopy (SEM), differential scanning calorimetry, and X-ray diffraction. All analytical characterizations have concordantly shown that the products are formed by intricate mixtures of unreacted PPAA and SBH together with PP-g-SBH copolymers of different composition. Exploratory experiments carried out by adding small amounts of COPP50 or COPP70 into binary mixtures of isotactic polypropylene (iPP) and SBH while blending have demonstrated that this practice leads to an appreciable improvement of the dispersion of the minor LCP phase, as well as to an increase of the crystallization rate of iPP. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 391–403, 1998     

Crystalline structure of propylene–ethylene copolymer fractions

Crystalline structure were studied on both block and random propylene–ethylene copolymer fractions, which were obtained by temperature rising elution fractionation. The peak characteristic of α-polypropylene (PP) was observed for all fractions, except the fraction eluted at room temperature. A characteristic peak of polyethylene crystals [i.e., (200) planes] was observed in some fractions, indicating the existence of long ethylene sequence in these fractions. This is in accordance with the analysis from Fourier transform infrared spectroscopy and ¹³C-NMR. The γ-form crystal of PP was observed in these copolymer fractions at atmospheric pressure. It is suggested that the insertion of comonomer into the isotactic PP chain makes the crystallizable sequences sufficiently short and produces the γ-form crystal. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68:381–386, 1998     

Synthesis of polyurethane–imide (PU–imide) copolymers with different dianhydrides and their properties

This study reports the synthesis of polyurethane–imide (PU–imide) copolymers using 4,4′-diphenylmethane diisocyanate (MDI) polytetramethylene glycols (PTMGs) and different aromatic dianhydrides. Differential scanning calorimetry (DSC) results indicate that PU–imide copolymers had two phase structures containing four transition temperatures (T_gs, T_ms, T_gh and T_mh). However, only PU–imide copolymers were formed by soft PTMG(2000) segments possessing a T_ms (melting point of soft segment). When different aromatic dianhydrides were introduced into the backbone chain of the polyurethane, although the T_gs (glass transition temperature of the soft segment) of some of PU–imide copolymers did not change, the copolymers with long soft segments had low T_gs values. The T_gh (glass transition temperature of hard segment) values of PU–imide copolymers were higher than that of polyurethane (PU). In addition, the high hard segment content of PU–imide copolymer series also had an obvious T_mh (melting point of hard segment). According to thermogravimetric analysis (TGA) and differential thermogravimetric analysis (DTGA), the PU–imide copolymers had at least two stages of degradation. Although the T_di (initial temperature of degradation) depended on the hard segment content and the composition of hard segment, the different soft segment lengths did not obviously influence the T_di. However, PU–imide copolymers with a longer soft segment had a higher thermal stability in the degradation temperature range of middle weight loss (about T_d 5%–50%). However, beyond T_d 50% (50% weight loss at temperature of degradation), the temperature of degradation of PU–imide copolymers increased with increasing hard segment content. Mechanical properties revealed that the modulus and tensile strength of PU–imide copolymers surpassed those of PU. Wide angle X-ray diffraction patterns demonstrated that PU–imide copolymers are crystallizable. © 1999 Society of Chemical Industry     

Nonisothermal crystallization of metallocene propylene–decene‐1 copolymers

The nonisothermal crystallization behavior of one metallocene‐based isotactic polypropylene and three propylene–decene‐1 copolymers was studied. The effects of comonomer content and cooling rate were investigated. It was found that comonomer units enchained systematically reduce the crystallization temperature (T_c), melting temperature (T_m), fusion enthalpy (ΔH_f), and crystallinity (X_c). Such an effect becomes more evident at a faster cooling rate. With increasing comonomer content, the supercooling required for crystallization increases and the overall crystallization rate is reduced. The Avrami equation is applicable to describe the nonisothermal crystallization kinetics of propylene–decene‐1 copolymer. It was shown that, although the reduced crystallization rate constant Z_c increases with comonomer content, the Avrami exponent decreases with comonomer content and cooling rate, leading to the smaller overall crystallization rate and larger crystallization half‐time of the copolymer with higher comonomer content. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1724–1730, 2004     

Fracture behaviour of controlled‐rheology ethylene–propylene block copolymers

The evolution of the molecular weight distribution and the thermal, mechanical and fracture behaviour of controlled‐rheology ethylene‐propylene block copolymers (ca 8 wt% ethylene content) has been analysed. Various concentrations of di‐tert‐butylperoxide were utilized. The melt flow index increased with the peroxide content due to the reduction of the molecular weight and the narrowing of the molecular weight distribution. However, the thermal behaviour and degree of crystallinity were not improved and some mechanical properties, such as the tensile strength and elongation at break, presented an anomalous behaviour. This trend can be explained by the presence of the elastomeric phase. The addition of peroxide influenced strongly the J–R curves obtained via the elastic–plastic fracture mechanics approach. The slope of these curves was markedly reduced with addition of peroxide to almost being flat for the highest concentration. This loss of ductility and the sudden decrease of the fracture toughness values with an increasing amount of peroxide were mainly due to the reduction in the molecular weight. Copyright © 2011 Society of Chemical Industry     

DSC analysis of ethylene/1-butene copolymers obtained with different ziegler–natta catalysts

The crystallization and melting behaviour of two sets of ethylene/1-butene copolymers have been analysed by DSC. The samples, with comonomer content in the range from 0 to 21.5 mol%, were obtained by industrial processes using both Mg/Ti-based catalyst systems. The composition dependences of melting and crystallization temperatures were found to be strictly affected by the catalyst type. Moreover, logarithmic plots of the melting and crystallization enthalpy as a function of the ethylene content (mol%) in the copolymers fitted linear relationships whose slopes have been related to the critical sequence length of crystallizable ethylene units, depending on the catalytic system. These results are compared with those reported in the literature for ethylene/1-butene copolymers synthesized by other catalysts and are accounted for by a different distribution of the comonomer units in the macromolecules of the two sets of samples.     

Synthesis and characterization of rubbery highly fluorinated siloxane–imide segmented copolymers

The synthesis and characterization of a series of poly(siloxane–imide) block (or segmented) copolymers obtained by copolymerization of amine‐terminated polydimethylsiloxane with fluorinated aromatic compounds containing anhydride and amine functionality are reported. New fluorinated block copolymers have been synthesized to obtain organophilic polyimides potentially interesting for molecular membrane separations. The new aspects of this work relative to the literature are (1) a comparison of solution and solid‐state approaches in the imidization step to generate the target poly(siloxane–imide) copolymers and (2) exploration of new compositions involving fluorinated aromatic polymers derived from added diamine compounds. It is shown that the copolymer properties can be tailored from glassy to rubbery materials by varying the amount and the type of oligosiloxane used; the transition between glassy and rubbery properties is characterized at a siloxane content of 60 wt%. As a main result, it is shown that the solid‐state approach for inducing the cyclo‐imidization step is the more efficient one for synthesizing polymers with good mechanical properties, when the amount of siloxane block is increased in the copolymer series. Physical and chemical methods (thermogravimetric analysis, Fourier transform infrared spectroscopy, viscosity measurements) were used to characterize the copolymer properties obtained according to the two different synthesis routes. The obtained siloxane–imide copolymers are well soluble in a large variety of moderately polar solvents and exhibit very good thermal stability up to 400 °C. Hence the prepared copolyimides would seem to be promising candidates as organophilic membranes as well as gas permeation membranes. © 2012 Society of Chemical Industry     

Compositional and configurational sequence determination of methacrylonitrile–vinylidene chloride copolymers by nuclear magnetic resonance spectroscopy

Methacrylonitrile–vinylidene chloride (M/V) copolymers of different composition were prepared by bulk polymerization using benzoyl peroxide as an initiator under nitrogen atmosphere in a sealed tube. The copolymer composition was determined from quantitative ¹³C[¹H] NMR spectra. The reactivity ratios for M/V copolymers obtained from a linear Kelen–Tudos method and nonlinear error‐in‐variables method are r_M = 2.47 ± 0.14, r_V = 0.40 ± 0.02, and r_M = 2.43, r_V = 0.39, respectively. The complete spectral assignment in term of compositional and conformational sequences of these copolymers were done with the help of distortionless enhancement by polarization transfer, two‐dimensional heteronuclear single‐quantum coherence spectroscopy. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1865–1874, 2005     

Solubility behavior of amphiphilic sulfonated copolymers based on styrene–stearyl methacrylate and styrene–stearyl cinnamate

Amphiphilic polymers have found many applications, so many types of these copolymers have been prepared. Specifically, sulfonated polystyrene acts, for example, as a flocullant or dispersant of petroleum asphaltenes as a function of its hydrophilic–hydrophobic balance. However, when changing the sulfonation degree, looking for the best performance, the solubility also changes, and sometimes it is responsible for making the polymer unsuitable for any application. Therefor, this work investigates in detail the changes in the solubility range of copolymers based on styrene–stearyl methacrylate and styrene–stearyl cinnamate with different molar compositions and different sulfonation degrees. The copolymers were synthesized and characterized by ¹H‐NMR, Fourier transform infrared spectroscopy, and elemental analysis. In the range of compositions analyzed, with increasing content of long hydrocarbon chains, not only the displacement of the solubility in solvents with lower solubility parameter (δ), but also the broadening of the solubility range was observed. In general, the solubility was directly related to the sulfonic group content, but there appeared to be an influence of the randomness of the sulfonation reactions along the chains. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43112.     

Acrylamide‐b‐N‐isopropylacrylamide block copolymers: Synthesis by atomic transfer radical polymerization in water and the effect of the hydrophilic–hydrophobic ratio on the solution properties

A series of block copolymers of acrylamide and N‐isopropylacrylamide (NIPAM) characterized by different ratios between the length of the two blocks have been prepared through atomic transfer radical polymerization in water at room temperature. The solution properties of the block copolymers were correlated to their chemical structure. The effect of the hydrophilic/hydrophobic balance on the critical micelle concentration (CMC) was investigated. The CMC increases at higher values for the solubility parameter, thus indicating a clear relationship between these two variables. In addition, the solution rheology (in water) of the block copolymers was studied to identify the effect of the chemical structure on the thermo‐responsiveness of the solutions. An increase in the length of the PNIPAM block leads to a more pronounced increase in the solution viscosity. This is discussed in the general frame of hydrophobic interactions strength. The prepared polymers are in principle suitable for applications in many fields, particularly in enhanced oil recovery. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39785.     

Wood-fiber reinforcement of styrene–maleic anhydride copolymers

Styrene–maleic anhydride (SMA) copolymers containing either 7 or 14% maleic anhydride were filled with either pine flour or dry-process aspen fiber from a medium density fiberboard (MDF) plant. Material properties of the filled and unfilled SMA plastics were compared with those of aspen-fiber-filled and unfilled polystyrene (PS). The fiber-filled SMA composites were equivalent or superior to unfilled SMA in strength, stiffness, and notched Izod impact strength. Filled PS composites outperformed or matched the performance of filled SMA composites in the parameters tested. Unnotched Izod impact strength of filled polymers was generally inferior to that of the unfilled polymers. Water absorption from a 90% relative humidity exposure, a 24-h soak, and a 2-h boil showed mixed results when compared to the unfilled polymers. Dynamic mechanical analysis showed no change in glass transition temperature (T_g) after the addition of filler for either SMA or PS composites. The presence of the anhydride functionality on the polymer backbone did not appear to improve the strength of the composite. No evidence was found for chemical bond formation between the SMA and wood fiber. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 1567–1573, 1998     

Kinetics of CO hydrogenation over coprecipitated cobalt–alumina

The kinetics of CO hydrogenation over coprecipitated 36 wt% Co/Al₂O₃ was studied in a fixed-bed microreactor at atmospheric pressure. Intrinsic kinetic data were obtained in the initial rate region using four different CO concentrations and two different H₂/CO ratios over the 473–523 K temperature range. The surface carbide mechanism with dissociative adsorption of hydrogen as the rate controlling step gives the most plausible kinetic model among the eight different models tested. C₁–C₄ production rates are found to be strongly influenced by temperature, and optimum C₁–C₄ hydrocarbon selectivity is obtained at 508 K. The activation energy for CO consumption and CH₄ formation are calculated as 74±2 kJ mol⁻¹ and 84±2 kJ mol⁻¹ respectively. ©1997 SCI     

Rheological characteristics and morphologies of styrene–butadiene–maleic anhydride block copolymers

Studies on the morphologies and rheological characteristics of two styrene–butadiene–maleic anhydride block copolymers (SBMa) have been performed. The transmission electron microscopy micrographs show that the morphologies of SBMa change from matrix–island structure to co‐continuous structure. Curves for dynamic modulus varied with frequency (ω) show obvious solid‐like behavior in the low ω region, which is typical for ordered block copolymers or networked materials. Van Gurp–Palmen plots have been used to exploit the thermorheological complexity of two copolymers. The master curves of two copolymers have been acquired through time–temperature superposition principle, and the plateau modulus (G) have been obtained from G′ at ω, where the loss tangent (tan δ) approaches a minimum. Meanwhile, Williams–Landel–Ferry equation has been used to evaluate the free volume parameters. The relaxation time spectra of two copolymers have been calculated and fitted with modified Baumgaertel–Schausberger–Winter model. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012