Experimental study on combustion of torrefied palm kernel shell (PKS) in oxy‐fuel environment

Oxy‐combustion of biomass can be a major candidate to achieve negative emission of CO₂ from a pulverized fuel (pf)‐firing power generation plants. Understanding combustion behavior of biomass fuels in oxy‐firing conditions is a key for design of oxy‐combustion retrofit of pulverized fuel power plant. This study aims to investigate a lab‐scale combustion behavior of torrefied palm kernel shell (PKS) in oxy‐combustion environments in comparison with the reference bituminous coal. A 20 kW_th‐scale, down‐firing furnace was used to conduct the experiments using both air (conventional) and O₂/CO₂ (30 vol% for O₂) as an oxidant. A bituminous coal (Sebuku coal) was also combusted in both air‐ and oxy‐firing condition with the same conditions of oxidizers and thermal heat inputs. Distributions of gas temperature, unburned carbon, and NO_x concentration were measured through sampling of gases and particles along axial directions. Moreover, the concentrations of SO_x and HCl were measured at the exit of the furnace. Experimental results showed that burnout rate was enhanced during oxy‐fuel combustion. The unburnt carbon in the flue gas was reduced considerably (~75%) during combustion of torrefied PKS in oxy‐fuel environment as compared with air‐firing condition. In addition, NO emission was reduced by 16.5% during combustion of PKS in oxy‐fuel environment as compared with air‐firing condition.     

Thermogravimetric analysis and process simulation of oxy‐fuel combustion of blended fuels including oil shale,semicoke, and biomass

Oxy‐fuel (OF) combustion is considered as one of the promising carbon capture and storage technologies for reducing CO₂ emissions from power plants. In the current work, the thermal behaviour of Estonian oil shale (EOS) and its semicoke (SC), pine saw dust, and their blends were studied comparatively under model air (21%O₂/79%Ar) and OF (30%O₂/70%CO₂) conditions using thermogravimetric analysis. Mass spectrometry analysis was applied to monitor the evolved gases. The effect of SC and pine saw dust addition on different combustion stages was analysed using kinetic analysis methods. In addition, different co‐firing cases were simulated using the ASPEN PLUS V8.6 (APV86) software tool to evaluate the effects of blending EOS with different biomass fuels of low and high moisture contents. The specific boiler temperatures of each simulated case with the same adjusted thermal fuel input were calculated while applying the operation conditions of air and OF combustion. According to the experiment and process simulation results, the low heating value and high carbonate content of SC brings along endothermic decomposition of carbonates, which negatively affects the heat balance during the conventional co‐combustion of EOS with SC. Instead, firing of EOS with SC and biomass in OF process can be an effective solution to reduce the environmental impact in terms of the reduction of CO₂ emissions and ash. Furthermore, the sensible heat from SC can positively affect the energy balance of the system as the endothermic effect of decomposition of CaCO₃ (for both EOS and SC) can be avoided in OF combustion.     

我国生物质直燃发电问题探讨

针对生物质直燃电厂可否大规模发展的问题,对比了秸秆综合利用途径效益及消化能力,得出生物质直燃发电是我国现阶段最具现实意义的秸秆资源化利用技术。通过分析现有生物质直燃电厂存在的问题,获得了直燃电厂利用秸秆资源的关键在于直燃机组参数、容量、布局均要基于辐射区内秸秆冗余量来规划,同时政府在电价上要给予一定的配套支持。     

The role of policy instruments for promoting combined heat and power production with low CO2 emissions in district heating systems

Policy instruments clearly influence the choice of production technologies and fuels in large energy systems, including district heating networks. Current Swedish policy instruments aim at promoting the use of biofuel in district heating systems, and at promoting electric power generation from renewable energy sources. However, there is increasing pressure to harmonize energy policy instruments within the EU. In addition, natural gas based combined cycle technology has emerged as the technology of choice in the power generation sector in the EU. This study aims at exploring the role of policy instruments for promoting the use of low CO₂ emissions fuels in high performance combined heat and power systems in the district heating sector. The paper presents the results of a case study for a Swedish district heating network where new large size natural gas combined cycle (NGCC) combined heat and power (CHP) is being built. Given the aim of current Swedish energy policy, it is assumed that it could be of interest in the future to integrate a biofuel gasifier to the CHP plant and co‐fire the gasified biofuel in the gas turbine unit, thereby reducing usage of fossil fuel. The goals of the study are to evaluate which policy instruments promote construction of the planned NGCC CHP unit, the technical performance of an integrated biofuelled pressurized gasifier with or without dryer on plant site, and which combination of policy instruments promote integration of a biofuel gasifier to the planned CHP unit. The power plant simulation program GateCycle was used for plant performance evaluation. The results show that current Swedish energy policy instruments favour investing in the NGCC CHP unit. The corresponding cost of electricity (COE) from the NGCC CHP unit is estimated at 253 SEK MWh^?1, which is lower than the reference power price of 284 SEK MWh^?1. Investing in the NGCC CHP unit is also shown to be attractive if a CO₂ trading system is implemented. If the value of tradable emission permits (TEP) in such as system is 250 SEK tonne^?1, COE is 353 SEK MWh^?1 compared to the reference power price of 384 SEK MWh^?1. It is possible to integrate a pressurized biofuel gasifier to the NGCC CHP plant without any major re‐design of the combined cycle provided that the maximum degree of co‐firing is limited to 27–38% (energy basis) product gas, depending on the design of the gasifier system. There are many parameters that affect the economic performance of an integrated biofuel gasifier for product gas co‐firing of a NGCC CHP plant. The premium value of the co‐generated renewable electricity and the value of TEPs are very important parameters. Assuming a future CO₂ trading system with a TEP value of 250 SEK tonne^?1 and a premium value of renewable electricity of 200 SEK MWh^?1 COE from a CHP plant with an integrated biofuelled gasifier could be 336 SEK MWh^?1, which is lower than both the reference market electric power price and COE for the plant operating on natural gas alone. Copyright © 2005 John Wiley & Sons, Ltd.     

The lignite electricity‐generating sector in Greece: Current status and future prospects

Lignite plays an important role in Greece's energy sector as it satisfies over 70% of country's needs in electric power. The extraction of lignite takes place mainly in three regions of Greece, namely Ptolemais‐Amyndeon, Megalopolis and Florina. The annual production of lignite is around 60 million tons, out of which 48 million tons derive from the coal fields of northern Greece (Ptolemais‐Amyndeon and Florina). Almost the entire lignite production is consumed for electricity generation, while small amounts of lignite are used for briquettes and other applications. The Greek coal‐fired power plants, which are about 4500 MW, use conventional technology and they are old (an average of 30 years). In the coming years new coal fields will be exploited in Florina—another 2.5 million tons of coal—in order to satisfy the currently under construction 365 MW plant located at Meliti, Florina, Northern Greece. Even though the lignite reserves are widespread in Greece and other areas such as Elassona and Drama could possibly host power plants, it is expected that the Florina power plant will be the last coal‐fired plant to be build in the country. Lignite has to compete with natural gas—the construction of the main gas pipeline network has been completed—imported oil and renewable energy sources. The new EU regulations on power plant emissions raise obstacles for the firing of lignite, although it is low in sulphur. It must be shown that lignite produces low cost electricity in a environmentally friendly manner. The utilization of fly ash and land reclamation can improve the situation in lignite mining. In particular, specific attention was paid to further research and potential use of fly ash in road construction, the production of bricks and concrete, and the production of zeolites from lignitic fly ash. The use of clean coal technologies in power plants can solve many emission problems. Specific measures to increase the efficiency of lignite‐fired power units might include: identification of the loss sources of every unit, improvement of the cold end of the steam turbines, optimization of the beater wheel mills operation, and the combination of natural gas‐fired turbines with the existing boilers. The liberalization of the electricity market needs to be considered seriously from the lignite industry, since the potential electricity producers can freely choose from all kinds of fuels, such as imported coal, oil, gas and renewables. However, Greek lignite meets the requirements for the security of supply, as indicated in the EU's Green Paper. It needs only to be competitive in the new energy sector by improving mining and combustion conditions. Further research on these topics, through the European Commission's ECSC and Framework Programmes, as well as the national programmes, is required. Copyright © 2004 John Wiley & Sons, Ltd.     

Biomass co-firing options on the emission reduction and electricity generation costs in coal-fired power plants

Co-firing offers a near-term solution for reducing CO₂ emissions from conventional fossil fuel power plants. Viable alternatives to long-term CO₂ reduction technologies such as CO₂ sequestration, oxy-firing and carbon loop combustion are being discussed, but all of them remain in the early to mid stages of development. Co-firing, on the other hand, is a well-proven technology and is in regular use though does not eliminate CO₂ emissions entirely. An incremental gain in CO₂ reduction can be achieved by immediate implementation of biomass co-firing in nearly all coal-fired power plants with minimum modifications and moderate investment, making co-firing a near-term solution for the greenhouse gas emission problem. If a majority of coal-fired boilers operating around the world adopt co-firing systems, the total reduction in CO₂ emissions would be substantial. It is the most efficient means of power generation from biomass, and it thus offers CO₂ avoidance cost lower than that for CO₂ sequestration from existing power plants. The present analysis examines several co-firing options including a novel option external (indirect) firing using combustion or gasification in an existing coal or oil fired plant. Capital and operating costs of such external units are calculated to determine the return on investment. Two of these indirect co-firing options are analyzed along with the option of direct co-firing of biomass in pulverizing mills to compare their operational merits and cost advantages with the gasification option.     

Lignite‐fired air‐blown IGCC systems with pre‐combustion CO2 capture

Detailed analyses based on mass and energy balances of lignite‐fired air‐blown gasification‐based combined cycles with CO₂ pre‐combustion capture are presented and discussed in this work. The thermodynamic assessment is carried out with a proprietary code integrated with Aspen Plus^® to carefully simulate the selective removal of both H₂S and CO₂ in the acid gas removal station. The work focuses on power plants with two combustion turbines, with lower and higher turbine inlet temperatures, respectively, as topping cycle. A high‐moisture lignite, partially dried before feeding the air‐blown gasification system, is used as fuel input. Because the raw lignite presents a very low amount of sulfur, a particular technique consisting of an acid gas recycle to the absorber, is adopted to fulfill the requirements related to the presence of H₂S in the stream to the Claus plant and in the CO₂‐rich stream to storage. Despite the operation of the H₂S removal section representing a significant issue, the impact on the performance of the power plant is limited. The calculations show that a significant lignite pre‐drying is necessary to achieve higher efficiency in case of CO₂ capture. In particular, considering a wide range (10–30 wt.%) of residual moisture in the dried lignite, higher heating value (HHV) efficiency presents a decreasing trend, with maximum values of 35.15% and 37.12% depending on the type of the combustion turbine, even though the higher the residual moisture in the dried coal, the lower the extraction of steam from the heat recovery steam cycle. On the other hand, introducing the specific primary energy consumption for CO₂ avoided (SPECCA) as a measure of the energy cost related to CO₂ capture, lower values were predicted when gasifying dried lignite with higher residual moisture content. In particular, a SPECCA value as low as 2.69 MJ/kg_CO2 was calculated when gasifying lignite with the highest (30 wt.%) residual moisture content in a power plant with the advanced combustion turbine. Ultimately, focusing on the power plants with the advanced combustion turbine, air‐blown gasification of lignite brings about a reduction in HHV efficiency equal to almost 1.5 to 2.8 percentage points, depending on the residual moisture in the dried lignite, if compared with similar cases where bituminous coal is used as fuel input. Copyright © 2016 John Wiley & Sons, Ltd.     

生物质直燃发电厂锅炉炉型选择探讨

目前生物质直接燃烧发电是生物质利用的主流技术之一,锅炉设计选型是生物质发电厂技术的主要核心,选择什么样的炉型,不仅影响着生物质电厂的投资、经济型,还影响着生物质电厂的使用寿命。对生物质直燃发电厂的几个炉型比较研究,为生物质直燃发电厂的炉型选择提出建议,供生物质发电厂设计时参考。     

Effects of coal characteristics to performance of a highly efficient thermal power generation system based on pressurized oxy‐fuel combustion

Because of its fuel flexibility and high efficiency, pressurized oxy‐fuel combustion has recently emerged as a promising approach for efficient carbon capture and storage. One of the important options to design the pressurized oxy‐combustion is to determine method of coal (or other solid fuels) feeding: dry feeding or wet (coal slurry) feeding as well as grade of coals. The main aim of this research is to investigate effects of coal characteristics including wet or dry feeding on the performance of thermal power plant based on the pressurized oxy‐combustion with CO₂ capture versus atmospheric oxy‐combustion. A commercial process simulation tool (gCCS: the general carbon capture and storage) was used to simulate and analyze an advanced ultra‐supercritical(A‐USC) coal power plant under pressurized and atmospheric oxy‐fuel conditions. The design concept is based on using pure oxygen as an oxidant in a pressurized system to maximize the heat recovery through process integration and to reduce the efficiency penalty because of compression and purification units. The results indicate that the pressurized case efficiency at 30 bars was greater than the atmospheric oxy‐fuel combustion (base line case) by 6.02% when using lignite coal firing. Similarly, efficiency improvements in the case of subbituminous and bituminous coals were around 3% and 2.61%, respectively. The purity of CO₂ increased from 53.4% to 94% after compression and purification. In addition, the study observed the effects of coal‐water slurry using bituminous coal under atmospheric conditions, determining that the net plant efficiency decreased by 3.7% when the water content in the slurry increased from 11.12% to 54%. Copyright © 2016 John Wiley & Sons, Ltd.     

Effect of supplementary firing options on cycle performance and CO2 emissions of an IGCC power generation system

Supplementary firing is adopted in combined‐cycle power plants to reheat low‐temperature gas turbine exhaust before entering into the heat recovery steam generator. In an effort to identify suitable supplementary firing options in an integrated gasification combined‐cycle (IGCC) power plant configuration, so as to use coal effectively, the performance is compared for three different supplementary firing options. The comparison identifies the better of the supplementary firing options based on higher efficiency and work output per unit mass of coal and lower CO₂ emissions. The three supplementary firing options with the corresponding fuel used for the supplementary firing are: (i) partial gasification with char, (ii) full gasification with coal and (iii) full gasification with syngas. The performance of the IGCC system with these three options is compared with an option of the IGCC system without supplementary firing. Each supplementary firing option also involves pre‐heating of the air entering the gas turbine combustion chamber in the gas cycle and reheating of the low‐pressure steam in the steam cycle. The effects on coal consumption and CO₂ emissions are analysed by varying the operating conditions such as pressure ratio, gas turbine inlet temperature, air pre‐heat and supplementary firing temperature. The results indicate that more work output is produced per unit mass of coal when there is no supplementary firing. Among the supplementary firing options, the full gasification with syngas option produces the highest work output per unit mass of coal, and the partial gasification with char option emits the lowest amount of CO₂ per unit mass of coal. Based on the analysis, the most advantageous option for low specific coal consumption and CO₂ emissions is the supplementary firing case having full gasification with syngas as the fuel. Copyright © 2008 John Wiley & Sons, Ltd.     

Design of sustainable second-generation biomass supply chains

Operational and economic trade-offs in the design of second-generation biomass (SGB) supply chains guide the decisions about plant scale and location as well as biomass collection routes. This paper compares different SGB supply chain designs with a focus on mobile pyrolysis plants and centralized versus decentralized collection of biomass in terms of economic and environmental sustainability. Pyrolysis scenarios are also compared to fuel-upgrading and electricity production scenarios.The empirical context of this paper is based on a scenario analysis for processing lignocellulosic biomass, particularly landscape wood, reed and roadside grass available in the Overijssel region (Eastern Netherlands). Four scenarios are compared: (1) mobile pyrolysis plant processes the locally available biomass on-site into pyrolysis oil which is sent to a regional biofuel production unit for upgrading to marketable biofuel; (2) local biomass is collected and transported to a regional pyrolysis-based biofuel production unit for upgrading to a marketable biofuel; (3) mobile pyrolysis plant performs the on-site conversion to pyrolysis oil which is transported to an oil refinery outside the region (Rotterdam); and (4) collected biomass is sent to the nearest electricity production unit to generate electricity.The results show that processing SGB is costly and upgraded oil and refined oil are at least 65% more expensive compared to their fossil counterparts. In terms of economic and environmental performance, the mobile plant performs slightly better than a fixed plant. The energy output/input ratio range is between 6.99 and 7.54 and CO₂ emissions range is between 96 and 138 kg CO₂/t upgraded oil.     

Techno‐economic analysis of biomass/coal Co‐gasification IGCC systems with supercritical steam bottom cycle and carbon capture

In recent years, integrated gasification combined cycle technology has been gaining steady popularity for use in clean coal power operations with carbon capture and sequestration (CCS). This study focuses on investigating two approaches to improve efficiency and further reduce the greenhouse gas (GHG) emissions. First, replace the traditional subcritical Rankine steam cycle portion of the overall plant with a supercritical steam cycle. Second, add different amounts of biomass as feedstock to reduce emissions. Employing biomass as a feedstock has the advantage of being carbon neutral or even carbon negative if CCS is implemented. However, due to limited feedstock supply, such plants are usually small (2–50 MW), which results in lower efficiency and higher capital and production costs. Considering these challenges, it is more economically attractive and less technically challenging to co‐combust or co‐gasify biomass wastes with low‐rank coals. Using the commercial software, Thermoflow®, this study analyzes the baseline plants around 235 MW and 267 MW for the subcritical and supercritical designs, respectively. Both post‐combustion and pre‐combustion CCS conditions are considered. The results clearly show that utilizing a certain type of biomass with low‐rank coals up to 50% (wt.) can, in most cases, not only improve the efficiency and reduce overall emissions but may be economically advantageous, as well. Beyond a 10% Biomass Ratio, however, the efficiency begins to drop due to the rising pretreatment costs, but the system itself still remains more efficient than from using coal alone (between 0.2 and 0.3 points on average). The CO₂ emissions decrease by about 7000 tons/MW‐year compared to the baseline (no biomass), making the plant carbon negative with only 10% biomass in the feedstock. In addition, implementing a supercritical steam cycle raises the efficiency (1.6 percentage points) and lowers the capital costs ($300/kW), regardless of plant layout. Implementing post‐combustion CCS consistently causes a drop in efficiency (at least 7–8 points) from the baseline and increases the costs by $3000–$4000/kW and In recent years, integrated gasification combined cycle technology has been gaining steady popularity for use in clean coal power operations with carbon capture and sequestration (CCS). This study focuses on investigating two approaches to improve efficiency and further reduce the greenhouse gas (GHG) emissions. First, replace the traditional subcritical Rankine steam cycle portion of the overall plant with a supercritical steam cycle. Second, add different amounts of biomass as feedstock to reduce emissions. Employing biomass as a feedstock has the advantage of being carbon neutral or even carbon negative if CCS is implemented. However, due to limited feedstock supply, such plants are usually small (2–50 MW), which results in lower efficiency and higher capital and production costs. Considering these challenges, it is more economically attractive and less technically challenging to co‐combust or co‐gasify biomass wastes with low‐rank coals. Using the commercial software, Thermoflow®, this study analyzes the baseline plants around 235 MW and 267 MW for the subcritical and supercritical designs, respectively. Both post‐combustion and pre‐combustion CCS conditions are considered. The results clearly show that utilizing a certain type of biomass with low‐rank coals up to 50% (wt.) can, in most cases, not only improve the efficiency and reduce overall emissions but may be economically advantageous, as well. Beyond a 10% Biomass Ratio, however, the efficiency begins to drop due to the rising pretreatment costs, but the system itself still remains more efficient than from using coal alone (between 0.2 and 0.3 points on average). The CO₂ emissions decrease by about 7000 tons/MW‐year compared to the baseline (no biomass), making the plant carbon negative with only 10% biomass in the feedstock. In addition, implementing a supercritical steam cycle raises the efficiency (1.6 percentage points) and lowers the capital costs ($300/kW), regardless of plant layout. Implementing post‐combustion CCS consistently causes a drop in efficiency (at least 7–8 points) from the baseline and increases the costs by $3000–$4000/kW and $0.06–$0.07/kW‐h. The SO_x emissions also decrease by about 190 tons/year (7.6 × 10^?6 tons/MW‐year). Finally, the CCS cost is around $65–$72 per ton of CO₂. For pre‐combustion CCS, sour shift appears to be superior both economically and thermally to sweet shift in the current study. Sour shift is always cheaper, (by a difference of about $600/kW and $0.02‐$0.03/kW‐h), easier to implement, and also 2–3 percentage points more efficient. The economic difference is fairly marginal, but the trend is inversely proportional to the efficiency, with cost of electricity decreasing by 0.5 cents/kW‐h from 0% to 10% biomass ratio (BMR) and rising 2.5 cents/kW‐h from 10% to 50% BMR. Pre‐combustion CCS plants are smaller than post‐combustion ones and usually require 25% less energy for CCS due to their compact size for processing fuel flow only under higher pressure (450 psi), versus processing the combusted gases at near‐atmospheric pressure. Finally, the CO₂ removal cost for sour shift is around $20/ton, whereas sweet shift's cost is around $30/ton, which is much cheaper than that of post‐combustion CCS: about $60–$70/ton. Copyright © 2014 John Wiley & Sons, Ltd.     

电站煤粉炉生物质混燃技术及关键设备分析

生物质混燃发电技术是环境友好、高效经济的规模化利用技术,应用前景广阔.总结了现有生物质混燃技术和国内外应用现状,介绍了一种生物质能高效利用的新方式,即在煤粉炉中使用独立喷燃技术燃用生物质成型燃料的方案,该方案将成为未来发展方向.分析了生物质在大容量煤粉炉中混燃发电技术的可行性,讨论了该混燃技术的关键设备选型配置情况和系统要求,指出了该混燃技术要实现规模化推广存在的主要矛盾,并提出了相应的建议.     

Influence of biomass furnace volume change on flue gases burn out process

In this paper has been shown improvement of the existing furnace for biomass combustion in the way of improving energy efficiency and meeting environmental protection criteria. One of the main problems during baled biomass combustion process is high CO emission due to incomplete combustion of flue gases. By proper furnace dimensioning that problem can be avoided and also high investment costs can be reduced, since the cost of the furnace is 30–40% of total biomass plant costs. Two-dimensional turbulent flow model with homogeneous chemical reactions has been developed. Turbulent flow is considered using time averaging Navier–Stokes equations that are closed by k–ε turbulence model. Calculations based on the proposed models were conducted using commercial CFD package FLUENT. Accuracy of the model has been previously confirmed with experimental data obtained on the existing furnace. Comparative analysis of the results of modeling existing and proposed (improved) furnace has shown lower CO emission (more than 50% less CO emission) at the proposed furnace outlet.     

Comparison of the inhibition mechanisms of five types of inhibitors on spontaneous coal combustion

Five inhibitors—Zn/Mg/Al‐CO₃ layered double hydroxides (LDHs), thermosensitive hydrogel (P(NIPA‐co‐SA)), diammonium phosphate ((NH₄)₂HPO₄), sodium phosphate (Na₃PO₄), and magnesium chloride (MgCl₂)—commonly used to forestall the spontaneous combustion of anthracite and coke coal were investigated in this study, and the inhibition effects were quantified. According to the results of thermogravimetry, differential scanning calorimetry, Fourier transform infrared spectroscopy, and kinetic analysis, Zn/Mg/Al‐CO₃‐LDHs, P(NIPA‐co‐SA), and (NH₄)₂HPO₄ all exert substantial inhibiting effects on anthracite and coke coal. Specifically, P(NIPA‐co‐SA) was altered during the liquid‐to‐gel phase, which isolated the oxygen from the coal surface and produced an endothermic reaction that decreased the environmental temperature; this reaction further inhibited spontaneous combustion. Conversely, MgCl₂ promoted a combustion reaction and reduced the apparent activation energy of coal, increasing the risk of spontaneous combustion. This study provides a reference for selecting suitable inhibitors to prevent the spontaneous combustion of coal.     

600MW亚临界锅炉褐煤燃烧系统设计与运行

本文通过对华能某电厂600MW亚临界燃煤机组风扇磨高水份褐煤燃烧系统的分析，结合燃烧调整和性能考核试验报告，介绍了燃煤发电机组的超临界风扇磨高水份褐煤燃烧系统设计，为今后的系统设计与运行提供了宝贵的经验。     

Optimum conditions for a natural gas combined cycle power generation system based on available oxygen when using biomass as supplementary fuel

Due to the higher oxygen content and lower heating value, the amount of biomass required in a combined cycle, where it is used as supplementary fuel, to meet a given energy demand is such that the biomass consumes almost all of the oxygen remaining from gas turbine combustion process under certain conditions. This situation requires additional air for biomass combustion thus reducing the cycle efficiency and the net work output rate while increasing CO₂ emissions. Three conditions at which the oxygen is completely consumed are identified based on alterations in net fuel utilization. The first condition is linked to fuel utilization, which is observed to be significantly affected by variations in temperatures at three locations in the combined cycle (air temperature entering the gas turbine combustion chamber, gas turbine inlet temperature and HRSG inlet temperatures). The second condition relates to the characteristics of the feedstock (oxygen content of the biomass and heating value of natural gas). The heat loss due to combustion of natural gas and biomass is the third condition that affects oxygen availability. The current work assesses these conditions in order to identify the proper condition at which no additional air is required for supplementary firing of biomass.     

Exergy, exergoeconomic and environmental analyses and evolutionary algorithm based multi-objective optimization of combined cycle power plants

A comprehensive exergy, exergoeconomic and environmental impact analysis and optimization is reported of several combined cycle power plants (CCPPs). In the first part, thermodynamic analyses based on energy and exergy of the CCPPs are performed, and the effect of supplementary firing on the natural gas-fired CCPP is investigated. The latter step includes the effect of supplementary firing on the performance of bottoming cycle and CO₂ emissions, and utilizes the first and second laws of thermodynamics. In the second part, a multi-objective optimization is performed to determine the “best” design parameters, accounting for exergetic, economic and environmental factors. The optimization considers three objective functions: CCPP exergy efficiency, total cost rate of the system products and CO₂ emissions of the overall plant. The environmental impact in terms of CO₂ emissions is integrated with the exergoeconomic objective function as a new objective function. The results of both exergy and exergoeconomic analyses show that the largest exergy destructions occur in the CCPP combustion chamber, and that increasing the gas turbine inlet temperature decreases the CCPP cost of exergy destruction. The optimization results demonstrates that CO₂ emissions are reduced by selecting the best components and using a low fuel injection rate into the combustion chamber.     

Comparative studies of augmentation in combined cycle power plants

The attractive features of a combined cycle (CC) power plant are fuel flexibility, operational flexibility, higher efficiency and low emissions. The performance of five gas turbine‐steam turbine (GT‐ST) combined cycle power plants (four natural gas based plants and one biomass based plant) have been studied and the degree of augmentation has been compared. They are (i) combined cycle with natural gas (CC‐NG), (ii) combined cycle with water injection (CC‐WI), (iii) combined cycle with steam injection (CC‐SI), (iv) combined cycle with supplementary firing (CC‐SF) and (v) combined cycle with biomass gasification (CC‐BM). The plant performance and CO₂ emissions are compared with a change in compressor pressure ratio and gas turbine inlet temperature (GTIT). The optimum pressure ratio for compressor is selected from maximum efficiency condition. The specific power, thermal efficiency and CO₂ emissions of augmented power plants are compared with the CC‐NG power plant at the individual optimized pressure ratios in place of a common pressure ratio. The results show that the optimum pressure ratio is increased with water injection, steam injection, supplementary firing and biomass gasification. The specific power is increased in all the plants with a loss in thermal efficiency and rise in CO₂ emissions compared to CC‐NG plant. Copyright © 2013 John Wiley & Sons, Ltd.     

1000MW机组神华煤掺烧霍林河褐煤的试验研究

在某电厂1 000MW机组上进行了神华煤与霍林河褐煤掺烧试验,研究了褐煤掺烧比例对磨煤机最大出力、机组最大出力和机组性能的影响,在最佳褐煤掺烧比例下进行了燃烧优化试验并提出了掺烧褐煤后产生的问题及解决措施.结果表明：随着褐煤掺烧比例的增大,磨煤机最大出力逐渐降低;当褐煤掺烧比例大于40%时,机组最大出力将受到明显影响;在目前设备条件下,褐煤最佳掺烧比例为30%.在最佳褐煤掺烧比例下,额定负荷时省煤器最佳出口氧量偏置为＋0.4,最佳燃尽风挡板开度偏置为-10%.通过燃烧调整,基本上解决了掺烧褐煤后炉膛结焦问题,锅炉效率提高了0.07%,NOx排放质量浓度为293.2mg/m3.