Synthesis of branched polyethylene by in situ polymerization of ethylene with combined iron catalyst and Ziegler–Natta catalyst

2,6‐Bis(imino)pyridyl iron catalyst and traditional Ziegler–Natta catalyst were combined together as tandem catalytic system, activated with the mixture of TEA and MAO, and used for synthesis of branched polyethylene by in situ polymerization of ethylene. The branched polyethylene with branches from 8/1000C to 29/1000C was produced by adjusting reaction conditions: the amount of TEA, MAO, iron catalyst used, and reaction temperatures. Not only the short branches such as ethyl and butyl but also the longer branches (hexyl and longer than hexyl) were detected in the products. The products exhibited higher molecular weight and broader molecular weight distribution than those obtained from metallocene catalysts, which would provide the materials excellent mechanical properties and processability. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

浆液法高效催化剂的乙烯聚合行为

考察了浆液法聚乙烯高效催化剂在总压0．7MPa、氢气分压0．18MPa下的乙烯聚合行为，表明催化剂活性中心失活符合一级规律，Al/Ti的影响可用Langmiur-Hinshelwood吸附竞争模型来描述；温度在70－90℃条件下，利用Arrhenius方程计算出了催化剂聚合反应的表现活化能为0．11kJ/mol。     

Effect of diether as internal donor on MgCl2‐supported Ziegler–Natta catalyst for propylene polymerization

This article demonstrates the influence of the molar ratio between diether as internal donor and Magnesium dichloride in processing of the catalyst preparation on the catalytic performance for propylene polymerization with MgCl₂‐supported Ziegler–Natta catalyst. The effect of electron donor on catalyst is investigated. The experimental data find that diether content on catalyst increases and Ti content on catalyst decreases with the increase of diether/Mg molar ratio. This result indicates that diether as internal donor is not coordinated to Ti species but to Mg species on catalyst. The introduction of diether remarkably improves the catalytic activity. The extents of improvement closely connect with diether/Mg molar ratio. The stereospecificity of catalyst intensively depends on the structure of diether as internal donor. The possible model of multi‐active sites on heterogeneous Ziegler–Natta catalyst is proposed to explain these phenomena. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1399–1404, 2006     

Effect of electron donors on 1,3‐butadiene polymerization by a Ziegler–Natta catalyst based on neodymium

High‐cis polybutadiene produced by catalyst systems based on a rare earth is an elastomer used to produce green tires. This type of tire presents lower rolling resistance, which allows higher fuel economy, and thus fewer chemical compounds are discharged into the atmosphere. In this work, the influence of electron donors [tetrahydrofuran (THF) and tetramethylethylenediamine (TMEDA)] present in the polymerization solvent on the microstructure and molecular weight characteristics of the polybutadiene produced by neodymium catalysts was studied. The catalyst synthesis was carried out in glass bottles for 1 h at a temperature between 5 and 10°C. The catalyst components were diisobutylaluminum hydride, neodymium versatate, and tert‐butyl chloride. The polymerization reaction was carried out for 2 h. The reaction temperature was kept at 70± 3°C. The addition of TMEDA or THF above a determined concentration reduced the catalytic activity, molecular weight, and concentration of cis‐1,4 units (<96%), whereas the polydispersity increased. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2539–2543, 2005     

Ethylene polymerization using a novel MgCl2/SiO2‐supported Ziegler–Natta catalyst

A novel MgCl₂/SiO₂‐supported Ziegler–Natta catalyst was prepared using a new one‐pot ball milling method. Using this catalyst, polyethylenes with different molecular weight distributions were synthesized. The effects of the [Si]/[Mg] ratio, polymerization temperature and [Al]/[Ti] ratio on the catalytic activity, the kinetic behaviour and the molecular weight and the polydispersity of the resultant polymer were studied. It was found that the polydispersity index of the polymer could be adjusted over a wide range of 5–30 through regulating the [Si]/[Mg] ratio and polymerization temperature, and especially when the [Si]/[Mg] ratio was 1.70, the polydispersity index could reach over 25. This novel bi‐supported Ziegler–Natta catalyst is thus useful for preparing polyethylene with a required molecular weight distribution using current equipment and technological processes. Copyright © 2005 Society of Chemical Industry     

淤浆法乙烯聚合催化剂活性的实验室评价方法

为了在公司产品销售与售后中提供与客户可对接的乙烯催化剂活性评价数据,实验室建立了一套淤浆法乙烯聚合催化剂的活性评价装置。通过正交试验确定适合本实验室装置的实验参数。结果表明,在催化剂加入量(0.28～0.32) mg (以Ti含量计)、1.0 mol·L~(-1)的三乙基铝加入量2 mL、聚合反应系统中氢气与乙烯分压比0.28∶0.45和搅拌转速450 r·min~(-1)的条件下,得到的催化剂活性与催化剂工业应用结果存在较好的一致性,此评价方法可作为催化剂生产的常规质量控制检验方法,并为下游用户使用提供技术数据支持。     

Poly(propylene‐co‐ethylene) produced with a conventional and a self‐supported ziegler–natta catalyst: Effect of ethylene and hydrogen concentration on activity and polymer structure

A novel self‐supported emulsion‐based catalyst and a conventional MgCl₂‐supported Ziegler–Natta catalyst were used in the copolymerization of propylene and ethylene under industrial conditions using triethyl aluminium as cocatalyst and dicyclopentyl dimethoxy silane as external donor. The effects of the concentration of ethylene and hydrogen on the polymerization behaviors and polymer properties were investigated. The combined effect of both ethylene and hydrogen increased the relative activity of the novel catalyst more than for the conventional catalyst. This trend was consistent with our earlier observed higher degree of dormancy, due to 2,1 insertions, found with the novel catalyst. More importantly, the work has uncovered that the self‐supported catalyst incorporates ethylene in a more random fashion and produces copolymers with relatively narrow molecular weight distribution (MWD). These results in combination with polymer microstructure studies using Fourier transform infrared spectroscopy, ¹³C‐NMR spectroscopy, and differential scanning calorimetry all indicated that the novel catalyst has a narrower distribution of active site types than the conventional reference catalyst. The narrow composition of active site structures, the narrow MWD, and the random incorporation of ethylene into the polymer chain indicated that the emulsion‐based catalyst possesses features that to a certain degree tend to be more indicative for a single‐site‐like catalyst structure and behavior. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Copolymerization of ethylene–propylene using high‐activity bi‐supported Ziegler–Natta TiCl4 catalyst

Heterogeneous Ziegler–Natta TiCl₄ catalyst using MgCl₂ and SiO₂ as supports was prepared under controlled conditions. Mg(OEt)₂ was used as a starting material and was expected to convert to active MgCl₂ during catalyst preparation. Due to the high surface area and good morphological control, SiO₂ was chosen as well. Slurry copolymerization of ethylene and propylene (EPM) was carried out in dry n‐heptane by using the catalyst system SiO₂/MgCl₂/TiCl₄/EB/TiBA or TEA/MPT/H₂ at temperatures of 40–70°C, different molar ratios of alkyl aluminum : MPT : Ti, hydrogen concentrations, and relative and total monomers pressure. Titanium content of the catalyst was 2.96% and surface area of the catalyst was 78 m²/g. Triisobutyl aluminum (TiBA) and triethyl aluminum (TEA) were used as cocatalysts, while ethyl benzoate (EB) and methyl p‐toluate (MPT) were used as internal and external donors, respectively. H₂ was used as a chain‐transfer agent. Good‐quality ethylene propylene rubber (EPR) of rubber was obtained at the ratio of [TiBA] : [MPT] : [Ti] = 320 : 16 : 1 and polymerization temperature was 60°C. When TiBA was used as a cocatalyst, a higher and more rubberlike copolymer was obtained. For both of the cocatalysts, an optimum ratio of Al/Ti was obtained relative to the catalyst productivity. Ethylene content of the copolymer obtained increased with increasing TiBA concentration, while inverse results were obtained by using TEA. Addition of H₂ increased the reactivity of the catalyst. The highest product was obtained when 150 mL H₂/L solvent was used. Increasing temperature from 40 to 70°C decreased the productivity of the catalyst, while irregular behavior was observed on ethylene content. Relative pressure of P_P/P_E = 1.4 : 1 and total pressure of 1 atm was the best condition for the copolymerization. Polymers with ethylene contents of 25–84% were obtained. Increasing ethylene content of EPR decreased T_g of the polymer obtained to a limiting value. Viscosity‐average molecular weight (M_v) decreased with increasing temperature and TiBA and H₂ concentration. However, increasing the polymerization time increased the M_v. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2597–2605, 2004     

Propylene polymerization using MgCl2/ethylbenzoate/TiCl4 catalyst: Determination of titanium oxidation states

The chemical interaction of the catalyst MgCl₂/ethylbenzoate/TiCl₄ with the cocatalysts triethylaluminum and trisobutylaluminum was investigated to establish a relationship between the titanium oxidation states and the catalytic activity, polymer isotacticity, and polymer molecular weight in propylene polymerizations. This interaction was studied using different Al : Ti molar ratios by measuring the changes of the titanium oxidation states at different polymerization times. Both hydrogen and alkyl aluminum caused a reduction of Ti⁴⁺ species to lower oxidation states species Ti³⁺ and Ti²⁺. However, the Ti⁴⁺ species reduction appeared to be incomplete. It was found that the Ti⁴⁺ species undergoes a severe reduction as the Al : Ti molar ratio increases from 50 to 230 as overreduction takes place. This change of the Ti³⁺ species percentage with time was found to correlate with the rate–time profiles of propylene polymerization. From this observation, it would be fair to conclude that the trivalent titanium species is more likely to be the active titanium species for propylene polymerization than the aforementioned catalyst system. On the other hand, hydrogen addition was found to cause an increase in Ti³⁺ species. The increases in both hydrogen amount and/or Al : Ti molar ratio were found to cause a decrease in both molecular weight and polypropylene isotactic index. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 56–62, 2004     

Polymer-supported heterogeneous titanium-based Ziegler-Natta catalyst for ethylene polymerization

Reported here in, is the synthesis of polystyrene (PS)-supported Ziegler–Natta catalyst (PS-TiCl₄) by the reaction of PS and titanium tetrachloride (TiCl₄). PS was synthesized by emulsion polymerization using super critical CO₂ (sc-CO₂) as a medium. Three catalysts were synthesized by varying the TiCl₄/PS weight ratio in hexane medium. The resulting catalysts were characterized by Fourier transformed-infrared spectroscopy, UV–visible spectroscopy, scanning electron microscope and energy dispersive X-ray detector, X-ray diffraction analysis. The acidity of the catalysts in an acetone/water solution was measured by pH meter. The thermogravimetric analysis reveals that catalysts are stable upto 150–180°C. Due to their higher degree of thermal stability these catalysts may potentially be used as a support in conventional Ziegler–Natta catalyst for ethylene polymerization. These catalysts also showed good storability and its overall catalytic productivity are found to be 3720 g PE/g Ti. The productivity of the catalysts also depended on the titanium concentration in the polymer matrix. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

High temperature polymerization of propylene catalyzed by MgCl2‐supported Ziegler–Natta catalyst with various cocatalysts

Four cocatalysts, referred to as ethylaluminoxanes, were synthesized by the reaction between triethylaluminium (AIEt₃) and water under various molar ratios of H₂O/Al at ?78°C. Aluminoxanes were used as cocatalysts for a MgCl₂‐supported Ziegler–Natta catalyst for propylene polymerization at temperatures ranging from 70 to 100°C. When the polymerization was activated by AlEt₃, the activity as well as the molecular weight and isotacticity of the resulting polymer gradually dropped as the temperature varied from 70 to 100°C. When ethylaluminoxane was employed as the cocatalyst, good activity and high molecular weight and isotacticity were obtained at 100°C. Furthermore, when the cocatalyst varied from AlEt₃ to ethylaluminoxane, the atactic fraction and polymer fraction with moderate isotacticity decreased and the high isotactic fraction slightly increased, which indicated that the variation of the cocatalyst significantly affects the isospecificity of active sites. It was suggested that the reactivity of the Al‐Et group and the size of the cocatalyst were correlated to the performance of the Ziegler–Natta catalyst at different temperatures. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1978–1982, 2006     

新型高性能乙烯淤浆聚合Ziegler-Natta催化剂的开发

通过引入卤代醇类化合物制备了适用于乙烯淤浆聚合工艺的新型高性能Ziegler-Natta催化剂(简称GH催化剂)。采用分光光度计、扫描电子显微镜等表征了催化剂的组成、粒径和形态等;采用淤浆聚合法研究了催化剂的聚合性能,并与国产商业化催化剂(参比催化剂)进行了比较。结果表明:GH催化剂的活性达21.6 kg/g,聚乙烯堆密度达0.34 g/cm3,粒径≥75~830μm的聚乙烯粉料质量占聚乙烯粉料总质量的97.9%,且GH催化剂的氢调敏感性和其催化乙烯与1-己烯共聚合的性能均优于参比催化剂。     

Investigations of the initial state polymerization of propylene with Ziegler–Natta catalysts in slurry

The initial state polymerization of propylene with Ziegler–Natta catalysts has been investigated and discussed at very low polymerization yields under adiabatic industrial prepolymerization conditions in diluted slurry regarding the effects of significant process parameters like monomer pressure, aluminum alkyl, and donor kind and concentration including the morphology of the catalyst/polymer particles formed. A sharp temperature increase in the first minutes of the initial state polymerization is followed by a temperature maximum and a slow decrease. With cocatalyst triethyl aluminum (TEAL), high prepolymerization yields were already achieved at a molar ratio TEAL/Ti of 3.0, remaining about constant until ratios of at least 300. The external donor dicyclopentyl dimethoxy silane leads to higher polymerization yields than the donor cyclohexyl dimethoxymethyl silane in the initial state polymerization too; however, both show a remarkable decreasing effect on polymerization yield above a specific molar ratio donor/Ti obviously correlated with the bulkiness of the alkyl groups. The particle size of the catalyst and the catalyst/prepolymer particles is increasing with polymerization yield until about 22 g PP/g Cat with particles almost perfectly spherical. The particle size distribution is rather broad at lower prepolymerization stages but unifying with lower polymerization rates at higher polymerization times. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Supported zirconocene catalyst for preventing reactor fouling in ethylene polymerization

The commercial interest of metallocene complexes for olefin polymerization has led to additional efforts to prepare suitable metallocene complexes efficiently and economically. Ethylene polymerization was carried out with a series of heterogeneous catalysts which were prepared in various Zr/silica ratios by immobilization of Ind₂ZrCl₂ preactivated with methylaluminoxane (MAO) on silica. This method to form the catalyst system resulted in a polymerization catalyst with reduced fouling tendencies and improved reactor operability. Polymerization of ethylene was conducted in Buchi reactors in a slurry phase under mild pressure. Some of the physical properties of the obtained polymers were also determined. Copyright © 2005 Society of Chemical Industry     

Prepolymerization of ethylene with a Ziegler–Natta catalyst

The slurry prepolymerization of ethylene using TiCl₄/MgCl₂ as a catalyst was investigated. A 2³‐factorial experimental design method was employed to study the effects of the temperature, hydrogen, and active cocatalyst‐to‐catalyst molar ratio (Al/Ti) on the catalyst activity, prepolymer melt flow index, and powder bulk density. All dependent variables increased when the active Al/Ti ratio increased from 1 to 2. The hydrogen–Al/Ti interaction had a significant effect on the prepolymer melt flow index and catalyst activity. The hydrogen (partial pressure ranging from 0.5 to 1.5 bar) and temperature (ranging from 60 to 80°C) variables as well as the hydrogen–temperature and hydrogen–temperature–Al/Ti interactions increased the prepolymer powder bulk density, which ranged from 0.11 to 0.373 g/cc. To find the reason for the prepolymer powder bulk density variation with the operating conditions, the particle size distribution and crystallinity of the prepolymers were determined. The increasing catalyst activity, ranging from 132 to 660 g of polyethylene/mmol of Ti, enhanced the weight percentage of fines, which ranged from 3 to 60, and decreased the average particle size, which ranged from 562 to 120 μm. This was the reason for the increasing prepolymer powder bulk density and could be due to the breakup of the prepolymer particles during prepolymerization. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Polymerization of propylene using MgCl2 (ethoxide type)/TiCl4/diether heterogeneous Ziegler–Natta catalyst

Heterogeneous Ziegler–Natta catalyst of MgCl₂ (ethoxide type)/TiCl₄/diether was prepared. 2,2‐Diisobutyl‐1,3‐dimethoxy propane (DiBDMP), diether, was used as internal donor. Slurry polymerization of propylene was carried out using the catalyst in dry heptane while triethylaluminium (TEA) was used as co‐catalyst. The co‐catalyst effects, such as catalyst molar ratio, polymerization temperature, H₂ pressure, external donor, triisobutylaluminium (TiBA) and monomer pressure, on the activity of the catalyst and isotacticity index (II) of the polymers obtained were studied. Rate of polymerization versus polymerization time is of a decay type with no acceleration period. There are an optimum Al/Ti molar ratio and temperature to obtain the highest activity of the catalyst. The maximum activity was obtained at 60 °C. Increasing the monomer pressure to 1 010 000 Pa linearly increased the activity of the catalyst. Addition of hydrogen to 151 500 Pa pressure increased activity of the catalyst from 2.25 to 5.45 kg polypropylene (PP) (g cat)^?1 h^?1 using 505 000 Pa pressure of monomer. The II decreased with increasing Al/Ti ratio, monomer pressure, hydrogen pressure and increased with increasing temperature to 60 °C, following with decrease as the temperature increases. Productivity of 11.55 kg (PP) (g cat)^?1 h^?1 was obtained at 1 010 000 Pa pressure of monomer and temperature of 60 °C. Addition of methyl p‐toluate (MPT) and dimethoxymethyl cyclohexyl silane (DMMCHS) as external donors decreased the activity of the catalyst sharply, while the II slightly increased. Some studies of the catalyst structure and morphology of the polymer were carried out using FTIR, X‐ray fluorescence, scanning electron microscopy and Brunauer–Emmett–Teller techniques. Copyright © 2005 Society of Chemical Industry     

新型高氢调敏感性乙烯淤浆聚合用催化剂的制备

制备了一种新型高氢调敏感性乙烯淤浆聚合用催化剂(简称SEL催化剂)。考察了SEL催化剂的组成、粒子形态,催化乙烯均聚合与共聚合的性能,以及用其制备的聚乙烯的性能,并与商业化的同类型进口催化剂(简称参比催化剂)进行了对比。结果表明:SEL催化剂中钛含量高而镁含量低,粒径分布窄,颗粒形态规整;SEL催化剂催化乙烯聚合时氢调敏感性好,氢气分压为0.48 MPa,乙烯分压为0.25 MPa时,聚乙烯熔体流动速率达226.10g/10 min;SEL催化剂催化乙烯与1-己烯共聚合的性能和聚乙烯粉料中细粉含量等均优于参比催化剂。     

Kinetic and morphological study of a magnesium ethoxide‐based Ziegler–Natta catalyst for propylene polymerization

BACKGROUND: Kinetic and morphological aspects of slurry propylene polymerization using a MgCl₂‐supported Ziegler–Natta catalyst synthesized from a Mg(OEt)₂ precursor are investigated in comparison with a ball‐milled Ziegler–Natta catalyst. RESULTS: The two types of catalyst show completely different polymerization profiles: mild activation and long‐standing activity with good replication of the catalyst particles for the Mg(OEt)₂‐based catalyst, and rapid activation and deactivation with severe fragmentation of the catalyst particles for the ball‐milled catalyst. The observed differences are discussed in relation to spatial distribution of TiCl₄ on the outermost part and inside of the catalyst particles. CONCLUSION: The Mg(OEt)₂‐based Ziegler–Natta catalyst is believed to show highly stable polymerization activity and good replication because of the uniform titanium distribution all over the catalyst particles. Copyright © 2008 Society of Chemical Industry     

Copolymerization of ethylene and propylene catalyzed by novel magnesium chloride supported,vanadium‐based catalysts

Two novel magnesium chloride supported, vanadium‐based Ziegler–Natta catalysts with 9,9‐bis(methoxymethyl)fluorene and di‐i‐butyl phthalate as internal donors were prepared and used in the copolymerization of ethylene and propylene. The catalytic behaviors of these catalysts were investigated and compared with those of traditional magnesium chloride supported, vanadium‐based catalysts without internal donors. Differential scanning calorimetry, gel permeation chromatography, and ¹³C‐NMR spectroscopy analysis were performed to characterize the melting temperatures, molecular weights, and molecular weight distributions as well as structures and compositions of the products. The copolymerization kinetic results indicated that the novel catalyst with 9,9‐bis(methoxymethyl)fluorene as an internal donor had the highest catalytic activity and optimal kinetic behavior in ethylene–propylene copolymerization with an ethylene/propylene molar ratio of 44/56. Low‐crystallinity and high‐molecular‐weight copolymers were obtained with these novel magnesium chloride supported, vanadium‐based catalysts. The reactivity ratio data indicated that the catalytic systems had a tendency to produce random ethylene–propylene copolymers. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

MgCl2‐supported TiCl4 catalysts containing diethyl norbornene‐2,3‐dicarboxylate internal electron donor for 1‐butene polymerization: Effects of internal electron donor configuration

Three isomeric 5‐norbornene‐2,3‐dicarboxylic acid diethyl ester (NDDE) with endo‐, exo‐, and trans‐configuration have been synthesized and employed as internal electron donors (IED) in 1‐butene polymerization over magnesium chloride supported Ziegler–Natta catalysts. It was found that the configuration of NDDE plays a key role in tuning the catalyst activity, stereospecificity, molecular weight (MW), and polydispersity index (PDI) of resulting poly(1‐butene). The type of catalyst with cis‐5‐norbornene‐endo‐2,3‐dicarboxylic acid diethyl ester as IED shows the highest catalyst activity, while catalyst with trans‐NDDE as IED yields the poly(1‐butene) with the highest MW and the most broad PDI. IR results showed that the NDDE with endo‐, exo‐, and trans‐configuration have different coordination way to MgCl₂, subsequently affecting the catalysts performance. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40758.