Miscibility and transesterification in ternary blends of poly(ethylene naphthalate)/poly(pentamethylene terephthalate)/poly(ether imide)

Miscibility and morphology of poly(ethylene 2,6‐naphthalate)/poly(pentamethylene terephthalate)/poly(ether imide) (PEN/PPT/PEI) blends were studied by differential scanning calorimetry (DSC), optical microscopy (OM), proton nuclear magnetic resonance imaging (¹H‐NMR), and wide‐angle X‐ray diffraction (WAXD). OM and DSC results from ternary blends revealed the immiscibility of PEN/PPT/PEI blends, but ternary blends of all compositions were phase‐homogeneous following heat treatment at 300°C for over 60 min. Annealing samples at 300°C yielded an amorphous blend with a clear and single T_g at the final state. Experimental data from ¹H‐NMR revealed that PEN/PPT copolymers (ENPT) were formed by the so‐called transesterification. The effect of transesterification on glass transition and crystallization was discussed in detail. The sequence structures of the copolyester were identified by triad analysis, which showed that the mean sequence lengths became shorter and the randomness increased with heating time. The results reveal that a random copolymer improved the miscibility of the ternary blends, in which, the length of the homo segments in the polymer chain decreased and the crystal formation was disturbed because of the irregularity of the structure, as the exchange reaction proceeded. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3840–3849, 2006     

Preparation and properties of PET/PA6 copolymer/montmorillonite hybrid nanocomposite

From in situ polycondensation, a poly(ethylene terephthalate)/Polyamide 6 copolymer/montmorillonite nanocomposite was prepared, after the treatment of montmorillonite (MMT) with a water soluble polymer. The resulting nanocomposites were characterized by X‐ray diffraction (XRD), differential scanning calorimeter (DSC), nuclear magnetic resonance (NMR), dynamic mechanical analysis (DMA), and transmission electron microscopy (TEM). The results of DSC, ¹H NMR, and DMA proved that the nanocomposite synthesized was PET/PA6 copolymer/MMT nanocomposite, not the PET/PA6 blend/MMT nanocomposite. The results of XRD and TEM proved that the dispersion of MMT was improved observably after the introduction of PA6 molecular chain into PET. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2512–2517, 2006     

Synthesis and mesomorphic properties of side‐chain cholesteric liquid‐crystalline polymers containing menthyl groups

A series of new cholesteric liquid‐crystalline polysiloxanes ( P₁ – P₅ ) derived from menthyl groups were synthesized. The chemical structures of the monomers and polymers were characterized with Fourier transform infrared, ¹H‐NMR, ¹³C‐NMR, and elemental analyses. The mesomorphic properties and thermal behavior were investigated with differential scanning calorimetry, polarizing optical microscopy, thermogravimetric analysis, and X‐ray diffraction measurements. The influence of the polymer structure on the thermal behavior was discussed. The monomer diosgeninyl 4‐allyloxybenzoate exhibited a typical cholesteric oily‐streak texture and a focal‐conic texture. Polymers P₁ – P₅ showed thermotropic liquid‐crystalline properties. P₁ displayed a smectic fan‐shaped texture, P₂ – P₅ showed a cholesteric Grandjean texture, and P₆ and P₇ did not show mesomorphic properties. The experimental results demonstrated that the glass‐transition temperature and the clearing temperature decreased, and the mesomorphic properties weakened with an increasing concentration of menthyl units. Moreover, P₁ – P₅ exhibited wide mesophase temperature ranges and high thermal stability. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:5559–5565, 2006     

Synthesis and characterization of ABA type tri‐block copolymers derived from p‐dioxanone,L‐lactide and poly(ethylene glycol)

A series of triblock co‐polymers, consisting of a poly(ethylene glycol) (PEG) central block joined to two blocks of random p‐dioxanone‐co‐L ‐lactide copolymers were synthesized by ring‐opening polymerization of p‐dioxanone (PDO) and L ‐lactide (LLA) initiated by PEG in the presence of stannous 2‐ethylhexanoate catalyst. The resulting copolymers were characterized by various techniques including ¹H and ¹³C NMR and FTIR spectroscopies, gel permeation chromatography, inherent viscosity, wide‐angle X‐ray diffractometry (WAXD) and differential scanning calorimetry (DSC). The conversion of PDO and L ‐lactide into the polymer was studied various mole ratios and at different polymerization temperature from ¹H NMR spectra. Results of WAXD and DSC showed that the crystallinity of PEG macroinitiator was greatly influenced by the composition of PDO and L ‐lactide in the copolymer. The triblock copolymers with low molecular weight were soluble in water at below room temperature. © 2003 Society of Chemical Industry     

The architecture of hydroxy‐functionalized aPS‐b‐random copolymer‐b‐PE via one‐pot strategy combining living free radical polymerization with coordination polymerization

The copolymerization of styrene with ethylene was promoted by CpTiCl₃/BDGE/Zn/MAO catalyst system combining free radical polymerization with coordination polymerization via sequential monomer addition strategy in one‐pot. The effect of polymerization conditions such as temperature, time, ethylene pressure, and Al/Ti molar ratio on the polymerization performance was investigated. The hydroxy‐functionalized aPS‐b‐random copolymer‐b‐PE triblock copolymer was obtained by solvent extraction and determined by GPC, DSC, WAXD, and ¹³C‐NMR. The DSC result indicated that the aPS‐b‐random copolymer‐b‐PE had a T_g at 87°C and a T_m at 119°C which attributed to the T_g of aPS segment and the T_m of PE segment, respectively. The microstructure of the hydroxy‐functionalized aPS‐b‐random copolymer‐b‐PE was further confirmed by WAXD, ¹³C‐NMR, and ¹H‐NMR analysis; and these results demonstrated that the obtained block copolymer consisted of aPS segment, S‐E random copolymer segment, and crystalline PE segment. The connection polymerization of the hydroxy‐functionalized aPS with random copolymer‐b‐PE was revealed by GPC results. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Spectroscopic,thermal, and electrical investigations of PVDF films filled with BiCl3

Poly(vinylidene fluoride) (PVDF) films filled with BiCl₃ in the mass fraction range of 0.1 ≤ W ≤ 10 were prepared. α‐ and β‐Crystalline PVDF phases were detected and characterized by spectroscopic analysis. Fourier transform infrared analysis detected the presence of α‐ and β‐phase head‐to‐head and tail‐to‐tail polymer chain defects. The band detected at 1670 cm^?1 was assigned to C?C, indicating polarons in the polymeric matrix. The degree of crystallinity increased by increasing the filling level (FL), and the maximum relative β‐phase content was found at w = 5% FL. This result was confirmed by X‐ray diffraction (XRD) and differential scanning calorimetry (DSC) analysis. The X‐ray analysis confirmed the presence of α and β phases, and no peaks corresponding to pure BiCl₃ were found. DSC therograms showed a sharp endothermic peak at T₁ = 444 K for different FLs because of the melting. This peak was used to calculate the activation energy and the order of the reaction. The DC electrical resistivity was attributed to the one‐dimensional interpolaron hopping mechanism. The FL dependence of log ρ and hopping distance (R_o) at 373 K was observed, indicating the FL affected the distribution of the hopping sites. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2125–2131, 2006     

Nonionic water‐soluble polymer: Preparation,characterization, and application of poly(1‐vinyl‐2‐pyrrolidone‐co‐hydroxyethylmethacrylate) as a polychelatogen

The free‐radical copolymerization of water‐soluble poly(1‐vinyl‐2‐pyrrolidone‐co‐hydroxyethylmethacrylate) was carried out with a feed monomer ratio of 75:25 mol %, and the total monomer concentration was 2.67M. The synthesis of the copolymer was carried out in dioxane at 70°C with benzoyl peroxide as the initiator. The copolymer composition was obtained with elemental analysis and ¹H‐NMR spectroscopy. The water‐soluble polymer was characterized with elemental analysis, Fourier transform infrared, ¹H‐ and ¹³C‐NMR spectroscopy, and thermal analysis. Additionally, viscosimetric measurements of the copolymer were performed. The thermal behavior of the copolymer and its complexes were investigated with differential scanning calorimetry (DSC) and thermogravimetry techniques under a nitrogen atmosphere. The copolymer showed high thermal stability and a glass transition in the DSC curves. The separation of various metal ions by the water‐soluble poly(1‐vinyl‐2‐pyrrolidone‐co‐hydroxyethylmethacrylate) reagent in the aqueous phase with liquid‐phase polymer‐based retention was investigated. The method was based on the retention of inorganic ions by this polymer in a membrane filtration cell and subsequent separation of low‐molar‐mass species from the polymer/metal‐ion complex formed. Poly(1‐vinyl‐2‐pyrrolidone‐co‐hydroxyethylmethacrylate) could bind metal ions such as Cr(III), Co(II), Zn(II), Ni(II), Cu(II), Cd(II), and Fe(III) in aqueous solutions at pHs 3, 5, and 7. The retention percentage for all the metal ions in the polymer was increased at pH 7, at which the maximum retention capacity could be observed. The interaction of inorganic ions with the hydrophilic polymer was determined as a function of the pH and filtration factor. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 178–185, 2006     

Synthesis and characterization of a thermotropic liquid crystalline hyperbranched polyester

BACKGROUND: Hyperbranched polymers have received increasing attention in the fields of medicine, homogeneous catalysis and materials science. Hydroxyl‐functional aliphatic polyesters are one of the most widely investigated families of hyperbranched polymers. The research reported here is based on the preparation of a novel hyperbranched polyester and the modification of its terminal hydroxyl groups by biphenyl mesogenic units. RESULTS: 2,2,6,6‐Tetramethylolcyclohexanol as a core and 8‐[4′‐propoxy(1,1‐biphenyl)yloxy]octanoic acid as a mesogenic unit were synthesized. A hyperbranched polyester (HPE) was synthesized in one step and subsequently substituted by reaction of its terminal hydroxyl groups with the biphenyl mesogenic units to yield a novel liquid crystalline hyperbranched polyester (HPE‐LC). The chemical structures of all compounds were confirmed using Fourier transform infrared, ¹H NMR and ¹³C NMR spectroscopy. The thermal behavior and the mesogenic properties of the biphenyl mesogenic unit and HPE‐LC were investigated using differential scanning calorimetry, polarized optical microscopy and wide‐angle X‐ray diffraction. The results demonstrated that the degree of branching of the HPE is ca 0.63. Both HPE‐LC and the biphenyl mesogenic unit exhibit mesomorphic properties, but HPE‐LC has a lower isotropic transition temperature and a wider transition temperature range than the biphenyl mesogenic unit. CONCLUSION: A novel liquid crystalline hyperbranched polyester was successfully synthesized, which exhibits mesomorphic properties. This polymer has good solubility in highly polar solvents and good thermal stability. Copyright © 2009 Society of Chemical Industry     

Synthesis and characterization of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers with dibutylmagnesium as catalyst

Two series of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers were prepared by the ring opening polymerization of ε‐caprolactone in the presence of poly(ethylene glycol) and dibutylmagnesium in 1,4‐dioxane solution at 70°C. The triblock structure and molecular weight of the copolymers were analyzed and confirmed by ¹H NMR, ¹³C NMR, FTIR, and gel permeation chromatography. The crystallization and thermal properties of the copolymers were investigated by wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). The results illustrated that the crystallization and melting behaviors of the copolymers were depended on the copolymer composition and the relative length of each block in copolymers. Crystallization exothermal peaks (T_c) and melting endothermic peaks (T_m) of PEG block were significantly influenced by the relative length of PCL blocks, due to the hindrance of the lateral PCL blocks. With increasing of the length of PCL blocks, the diffraction and the melting peak of PEG block disappeared gradually in the WAXD patterns and DSC curves, respectively. In contrast, the crystallization of PCL blocks was not suppressed by the middle PEG block. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of hot air aging on the properties of ethylene‐vinyl acetate copolymer and ethylene‐acrylic acid copolymer blends

The aim of this investigation is to evaluate the effect of hot air aging on properties of ethylene‐vinyl acetate copolymer (EVA, 14 wt % vinyl acetate units), ethylene‐acrylic acid copolymer (EAA, 8 wt % acrylic acid units), and their blends. Attenuated total reflection‐Fourier transform infrared spectroscopy, differential scanning calorimeter (DSC), wide angle X‐ray diffraction, and mechanical tests are employed to investigate the changes of copolymer blends' structures and properties. Increase of carbonyl index derived from ATR measurements with aging time suggests the incorporation of oxygen into the polymeric chain. By DSC measurements, the enthalpy at low temperature endothermic peak (T_m2) of EAA becomes less and disappears after 8 weeks aging, but enthalpy at T_m2 of EVA is not influenced by the hot air aging and remains stable despite of the aging time. For various proportions of EAA and EVA blends, enthalpy at T_m2 decreases as the EAA proportion increases when aging time is 8 weeks; after several weeks of hot air aging, the various blends appear a same new peak just over the aging temperature 70°C which is due to the completion of crystals which are not of thermodynamic equilibrium state. Mechanical tests show that increase of crystallinity and hot air aging deterioration both have influence on the hardness, tensile strength, and elongation at break. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

1H NMR,thermal, and conductivity studies on PVAc based gel polymer electrolytes

The lithium‐ion conducting gel polymer electrolytes (GPE), PVAc‐DMF‐LiClO₄ of various compositions have been prepared by solution casting technique. ¹H NMR results reveal the existence of DMF in the gel polymer electrolytes at ambient temperature. Structure and surface morphology characterization have been studied by X‐ray diffraction analysis (XRD) and scanning electron microscopy (SEM) measurements. Thermal and conductivity behavior of polymer‐ and plasticizer‐salt complexes have been studied by differential scanning calorimetry (DSC), TG/DTA, and impedance spectroscopy results. XRD and SEM analyses indicate the amorphous nature of the gel polymer‐salt complex. DSC measurements show a decrease in T_g with the increase in DMF concentrations. The thermal stability of the PVAc : DMF : LiClO₄ gel polymer electrolytes has been found to be in the range of (30–60°C). The dc conductivity of gel polymer electrolytes, obtained from impedance spectra, has been found to vary between 7.6 × 10^?7 and 4.1 × 10^?4 S cm^?1 at 303 K depending on the concentration of DMF (10–20 wt %) in the polymer electrolytes. The temperature dependence of conductivity of the polymer electrolyte complexes appears to obey the VTF behavior. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Study on the Azido‐Tetrazolo Tautomerizations of 3,6‐Bis(azido)‐1,2,4,5‐tetrazine

The azido‐tetrazolo tautomerizations of 3,6‐diazido‐1,2,4,5‐tetrazine (DIAT) in different solvents were investigated with HPLC and ¹³C NMR spectroscopy. 6‐Amino‐tetrazolo[1,5‐b]‐1,2,4,5‐tetrazine (ATTZ) was irreversibly formed as the final product by azido‐cyclization following N₂ elimination from one of the azido substituents at room temperature in DMSO. The structure of ATTZ was characterized by X‐ray crystallography; differential scanning calorimetry (DSC), mass spectrometry, as well as IR and ¹H NMR and ¹³C NMR spectroscopy. The crystal density was found to be 1.272 g cm⁻³. DSC result suggested that ATTZ with the melting point of 84 °C strongly decomposes with explosion at 198 °C, which can be regarded as a primary explosive.     

Synthesis and structure of polysiloxane liquid crystalline elastomers with a mesogenic crosslinking agent

A new mesogenic crosslinking agent M‐1 was synthesized to minimize the perturbations of a nonmesogenic crosslinking agent for liquid crystalline elastomers. The synthesis of new side‐chain liquid crystalline elastomers containing a rigid mesogenic crosslinking agent M‐1 and a nematic monomer M‐2 is described by a one‐step hydrosilylation reaction. The chemical structures of the obtained monomers and elastomers were confirmed by ¹H NMR and FTIR spectroscopy. The mesomorphic properties and phase behavior were investigated by differential scanning calorimetry, polarizing optical microscopy, and X‐ray diffraction measurements. The influence of the crosslinking units on the phase behavior is discussed. The elastomers containing less than 15 mol % of the crosslinking units showed elasticity, reversible phase transition, and nematic‐threaded texture. However, when the crosslinking density reached 21.6 mol %, the mesophase of polymer P‐8 disappears. The adoption of a mesogenic crosslinking agent diminishes the perturbation of a nonmesogenic crosslinking agent on mesophase of liquid crystalline elastomers, and isotropic temperature and a mesomorphic temperature range slightly decreased with increasing content of the crosslinking agent. In addition, X‐ray analysis shows nematic polydomain network polymers can transform into smectic monodomain by stress induction, leading to the orientation formation macroscopically. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1736–1742, 2004     

New synthesis methods for polypropylene‐co‐ethylene‐propylene rubber

In this research, the reinforcement of polypropylene (PP) was studied using a new method that is more practical for synthesizing polypropylene‐block‐poly(ethylene‐propylene) copolymer (PP‐co‐EP), which can be used as a rubber toughening agent. This copolymer (PP‐co‐EP) could be synthesized by varying the feed condition and changing the feed gas in the batch reactor system using Ziegler–Natta catalysts system at a copolymerization temperature of 10°C. The ¹³C‐NMR tested by a 21.61‐ppm resonance peak indicated the incorporation of ethylene to propylene chains that could build up the microstructure of the block copolymer chain. Differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and dynamic mechanical analysis (DMA) results also confirmed these conclusions. Under these conditions, the morphology of copolymer trapped in PP matrix could be observed and the copolymer T_g would decrease when the amount of PP‐co‐EP was increased. DMA study also showed that PP‐co‐EP is good for the polypropylene reinforcement at low temperature. Moreover, the PP‐co‐EP content has an effect on the crystallinity and morphology of polymer blend, i.e., the crystallinity of polymer decreased when the PP‐co‐EP content increased, but tougher mechanical properties at low temperature were observed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3609–3616, 2007     

Synthesis and characterizations of branched poly(butylene succinate) copolymers with 1,2‐octanediol segments

Branched poly(butylene succinate) (PBS) copolymers were synthesized, from succinic acid (SA), 1,4‐butanediol (1,4‐BD), and 1,2‐octanediol (1,2‐OD) through a two‐step process containing esterification and polycondensation, with different mole fractions of 1,2‐OD segments. The branched PBS copolymers were characterized with ¹H‐NMR, differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), thermogravimetric analysis (TGA), dynamic rheological testing, and tensile properties analysis. The results of DSC and WAXD show that, with the increasing of the 1,2‐OD segments content, the glass transition temperature (T_g), melting temperature (T_m), crystallization temperature (T_c), and the degree of crystallinity (X_c) decrease. While the crystal structure of PBS does not change by introducing 1,2‐OD segments. The results of TGA and dynamic rheological testing indicate that the thermal stability of neat PBS is improved with the addition of 1,2‐OD segments. The incorporation of 1,2‐OD segments has some effects on the rheological properties of PBS, such as complex viscosities (|η*|), storage modulus (G′), and loss modulus (G″). Tensile testing demonstrates that the elongation at break is improved significantly with increasing 1,2‐OD segments content, but without a notable decrease of tensile strength. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of side‐chain liquid‐crystalline ionomers containing quaternary ammonium salt groups

A series of thermotropic side‐chain liquid‐crystalline ionomers (LCIs) containing 4‐(4‐alkoxybenzyloxy)‐4′‐allyloxybiphenyl (M) as mesogenic units and allyl triethylammonium bromide (ATAB) as nonmesogenic units were synthesized by graft copolymerization upon polymethylhydrosiloxane. The chemical structures of the polymers were confirmed by IR spectroscopy. DSC was used to measure the thermal properties of these polymers. The mesogenic properties were characterized by polarizing optical microscopy, DSC, and X‐ray diffraction. Homopolymers without ionic groups exhibit smectic and nematic mesophases. The nematic mesophases of the ionomers disappear and the mesomorphic temperature ranges decrease with increasing concentration of ionic units. The influence of the alkoxy chain length on clearing temperature (T_c) values of ionomers clearly shows an odd‐even effect, similar to that of other side‐chain liquid‐crystalline polymers. The mesomorphic temperature ranges increase with increasing alkoxy chain length when the number of alkoxy carbon is over 3. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2879–2886, 2003     

Synthesis and properties of copolyesters of p,p′‐bibenzoic acid,dimer acid,and alkylene glycol

Copolyesters of p,p′‐bibenzoic acid, dimer acid, and an alkylene glycol are prepared by melt polycondensation of of dimethyl p,p′‐bibenzoate, dimer acid, and an alkylene glycol. The copolyesters are characterized by the inherent viscosity, FTIR, proton NMR, DSC, polarized microscopy, and X‐ray diffraction. The polymer composition and sequence distribution of the copolyesters can be seen from the NMR spectra. The copolyesters exhibit a degree of randomness of about 1, indicating that they are random copolymers. The glass‐transition temperature (T_g) and the melting point (T_m) of the copolyesters are found from the DSC heating curves. When the content of the flexible dimer acid unit increases, the T_g of the copolyesters decreases significantly. The copolymerization effect decreases the crystallinity and the T_m of the copolyesters. It can be seen from the DSC, polarized microscopy, and X‐ray diffraction data that some copolyesters derived from 1,6‐hexanediol and 1,5‐pentanediol exhibit a monotropic smectic phase. As the molar content of the dimer acid unit increases, the isotropic–mectic transition temperature and the smectic order decreases significantly. The liquid crystallinity is completely destroyed at certain molar contents of the dimer acid unit. The smectic order of the copolyesters derived from 1,6‐hexanediol is significantly higher than that of the copolyesters derived from 1,5‐pentanediol, and it is described as an odd–even effect. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 750–758, 2003     

Synthesis and characterization of poly(urethane‐ester)s based on calcium salt of mono(hydroxybutyl)phthalate

Calcium‐containing poly(urethane‐ester)s (PUEs) were prepared by reacting diisocyanate (HMDI or TDI) with a mixture of calcium salt of mono(hydroxybutyl)phthalate [Ca(HBP)₂] and hydroxyl‐terminated poly(1,4‐butylene glutarate) [HTPBG₁₀₀₀], using di‐n‐butyltin‐dilaurate as catalyst. About six calcium‐containing PUEs having different composition were synthesized by taking the mole ratio of Ca(HBP)₂:HTPBG₁₀₀₀:diisocyanate (HMDI or TDI) as 3:1:4, 2:2:4, and 1:3:4. Two blank PUEs were synthesized by the reaction of HTPBG₁₀₀₀ with diisocyanate (HMDI or TDI). The polymers were characterized by IR, ¹H NMR, Solid state ¹³C‐CP‐MAS NMR, TGA, DSC, XRD, solubility, and viscosity studies. The T_g value of PUEs increases with increase in the calcium content and decreases with increase in soft segment content. The viscosity of the calcium‐containing PUEs increases with increase in the soft segment content and decreases with increase in the calcium content. X‐ray diffraction patterns of the polymers show that the HMDI‐based polymers are partially crystalline and TDI‐based polymers are amorphous in nature. The dynamic mechanical analysis of the calcium‐containing PUEs based on HMDI shows that with increase in the calcium content of polymer, modulus (g′ and g″) increases at any given temperature. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1720–1727, 2006     

Synthesis of multi‐block copolymer and its compatibilization to the blends of poly(ether ether ketone) with thermotropic liquid crystalline polymer

A multiblock copolymer (BCP) containing amorphous poly(aryl ether ketone) (PAEK) and thermotropic liquid crystalline polymer (TLCP) segments was synthesized. The chemical structure and properties of BCP were characterized by fourier‐transform infrared spectrometer (FTIR), differential scanning calorimeter (DSC), gel permeation chromatograms (GPC), thermogravimetry analysis, polar light microscope (PLM), and solubility test respectively. BCP can dissolve in chloroform because of soluble PAEK block bonded with TLCP block, which was insoluble. The peak of the original PAEK oligomer was no more present in the GPC traces of the block copolymer. These facts indicated that polymer synthesized should be copolymers of the two components rather than blends. A single T_g at 138.1°C and broad melting endotherm at 315.7°C can be observed. The liquid crystalline texture of BCP showed uniformity in the view after heat treated for 10 min above its T_m under PLM. Ternary blends of poly(ether ether ketone) (PEEK)/TLCP/BCP were prepared by extrusion and characterized by DSC. DSC results showed that the crystallization temperature of PEEK phase in the blends shifted higher with the addition of TLCP. Wide angle X‐ray diffraction investigations indicated that the crystalline structure of PEEK was not disturbed by blending or compatibilizing. Scanning electron microscope and mechanical tests confirmed the compatibilizing effect of BCP. Reduction in dispersed phase TLCP size was observed when 2 phr by weight of compatibilizer was added to the blend. Measurement of the tensile properties showed increased elongation as well as improved modulus and strength to some extent. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Synthesis and characterization of hyperbranched poly(silyl ester)s

Hyperbranched poly(silyl ester)s were synthesized via the A₂ + B₄ route by the polycondensation reaction. The solid poly(silyl ester) was obtained by the reaction of di‐tert‐butyl adipate and 1,3‐tetramethyl‐1,3‐bis‐β(methyl‐dicholorosilyl)ethyl disiloxane. The oligomers with tert‐butyl terminal groups were obtained via the A₂ + B₂ route by the reaction of 1,5‐dichloro‐1,1,5,5‐tetramethyl‐3,3‐diphenyl‐trisi1oxane with excess amount of di‐tert‐butyl adipate. The viscous fluid and soft solid poly(silyl ester)s were obtained by the reaction of the oligomers as big monomers with 1,3‐tetramethyl‐1,3‐bis‐β(methyl‐dicholorosilyl)ethyl disiloxane. The polymers were characterized by ¹H NMR, IR, and UV spectroscopies, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The ¹H NMR and IR analysis proved the existence of the branched structures in the polymers. The glass transition temperatures (T_g's) of the viscous fluid and soft solid polymers were below room temperature. The T_g of the solid poly(silyl ester) was not found below room temperature but a temperature for the transition in the liquid crystalline phase was found at 42°C. Thermal decomposition of the soft solid and solid poly(silyl ester)s started at about 130°C and for the others it started at about 200°C. The obtained hyperbranched polymers did not decompose completely at 700°C. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3430–3436, 2006