Thermal degradation kinetics of poly(O,O‐diethyl‐O‐allylthiophosphate‐co‐acrylonitrile) in nitrogen

The nonisothermal degradation kinetics of the copolymer poly(O,O‐diethyl‐O‐allylthiophosphate‐co‐acrylonitrile), which was synthesized with O,O‐diethyl‐O‐allylthiophosphate and acrylonitrile, were studied by thermogravimetry/derivative thermogravimetry techniques. The kinetic parameters, including the activation energy and the pre‐exponential factor of the copolymer degradation process, were calculated by the Kissinger and Flynn–Wall–Ozawa methods. The thermal degradation mechanism of the copolymer was also studied with the Satava–Sestak method. The results show that the activation energies were 138.17 kJ/mol with the Kissinger method and 141.63 kJ/mol with the Flynn–Wall–Ozawa method. The degradation of the copolymer followed a kinetic model of a phase boundary reaction and the kinetic equation could be expressed as G(α) = 1 ? (1 ? α)⁴ [where G(α) is the integral function of conversion and α is the extent of conversion of the reactant decomposed at time t]. The reaction order was 4. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

A study on the curing kinetics of epoxycyclohexyl polyhedral oligomeric silsesquioxanes and hydrogenated carboxylated nitrile rubber by dynamic differential scanning calorimetry

A new organic–inorganic hybrid material was prepared through reactive blending of hydrogenated carboxylated nitrile rubber (HXNBR) with epoxycyclohexyl polyhedral oligomeric silsesquioxanes (epoxycyclohexyl POSS). The structure of the composite was characterized by Fourier transform infrared spectroscopy (FTIR) and solid‐state ¹³C Nuclear Magnetic Resonance spectra (solid‐state ¹³C‐NMR). The differential scanning calorimetry (DSC) at different heating rates was conducted to investigate the curing kinetics. A single overall curing process by an nth‐order function (1 ? α)ⁿ was considered, and multiple‐heating‐rate models (Kissinger, Flynn–Wall–Ozawa, and Crane methods) and the single‐heating‐rate model were employed. The apparent activation energy (E_a) obtained showed dependence on the POSS content and the heating rate (β). The overall reaction order n was practically constant and close to 1. The isoconversion Flynn–Wall–Ozawa method was also performed and fit well in the study. With the single‐heating‐rate model, the average E_a for the compound with a certain POSS content, 66.90–104.13 kJ/mol was greater than that obtained with Kissinger and Flynn–Wall–Ozawa methods. Furthermore, the calculated reaction rate (dα/dt) versus temperature curves fit with the experimental data. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Thermal curing reaction and heat‐resistance of methyl‐di(M‐ethynylphenyl‐amino)silane

Methyl‐di(m‐ethynylphenyl‐amino)silane (MEAS) is a new kind of silazane with ethynylphenyl groups in the end of the molecule. The studies about the curing reaction kinetics and curing reaction mechanism are important for its application and performance. In this article, differential scanning calorimeter was used to study the curing reaction kinetics of MEAS. The results showed that both of the apparent activation energy (E_a) and the reaction order (n) that were evaluated with the method of Kissinger (113.4 kJ/mol, 0.93) agreed well with those using the method of Ozawa (116.1 kJ/mol, 0.95). According to structural changes during curing characterized using Fourier‐transform infrared spectra, it was inferred that MEAS resin underwent the main four kinds of cross‐linking reaction under the condition of heating. Thermogravimetric analysis was used to characterize the heat‐resistance of MEAS thermoset. The results showed that the temperature of 5% weight loss based on the initial weight (T_d5) of the thermoset was 632.4°C and the residue yield at 900°C was 86.4% in nitrogen. The thermoset sintered at 1450°C in argon transformed into a ceramic with yield of 71%, which was studied by scanning electron microscopy and X‐ray diffraction. The sintered products were smooth and hard solid and its chemical composition was made up of β‐SiC, α‐Si₃N₄ ceramic and free carbon. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Polymers based on N,N‐diglycidylaniline. I. Investigations of the curing kinetics by dynamic differential scanning calorimetry measurements

N,N‐Diglycidylaniline was reacted with aniline (yielding polymer EP‐1) and the newly synthesized chromophore 4‐(phenylazo)aniline (yielding polymer EP‐2). The curing kinetics of these two epoxy resin systems was studied in dynamic experiments by means of differential scanning calorimetry. Kinetic parameters such as the activation energy and frequency factor were estimated with the Ozawa method [E(O) and A(O), respectively], the Kissinger method [E(K) and A(K), respectively], and the modified Avrami method [E(A) and A(A), respectively]. The activation energy and frequency factor of EP‐1 were much lower than those of EP‐2 estimated with the Ozawa, Kissinger, and Avrami methods. The activation energy and frequency factor for EP‐1 determined with the Ozawa method [E(O) = 55.8 kJ/mol, A(O) = 10 × 10³ 1/s] and the Avrami method [E(A) = 56.4 kJ/mol, A(A) = 9.2 × 10³ 1/s] were higher than those determined with the Kissinger method [E(K) = 51.0 kJ/mol, A(K) = 2 × 10³ 1/s]. In the case of EP‐2, the kinetic parameters calculated with the Ozawa model [E(O) = 140.4 kJ/mol, A(O) = 12.3 × 10¹³ 1/s] and the Kissinger model [E(K) = 139.9 kJ/mol, A(K) = 10.9 × 10¹³ 1/s] were higher than those calculated with the Avrami model [E(A) = 130.4 kJ/mol, A(A) = 7.9 × 10¹² 1/s]. The obtained polymers were characterized with Fourier transform infrared, ¹H‐NMR, differential scanning calorimetry, and ultraviolet–visible spectroscopy. The polymers exhibited low glass‐transition temperatures in the range of 57–79°C and good solubility in common organic solvents. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Kinetics and thermal properties of epoxy resin cured with Ni(II)‐tris‐(O‐pheneylendiamine) bromide

Diglycidyl ether of bisphenol A (DGEBA) is cured with a nickel complex of O‐phenylendiamine (OPD) as a ligand. The structure of the synthesized curing agent is confirmed through IR and elemental analysis. The curing kinetics of DGEBA/Ni(OPD)₃Br₂ system is studied by the dynamic DSC and isothermal FTIR techniques. In all cases, we have observed at least two exothermic peaks during DSC traces up to 350°C. Dynamic activation energies are calculated by using the two isoconversional, Kissinger and Ozawa, methods applied to peak maximum. A two‐parameter (m, n) autocatalytic model (Sestak–Berggren equation) is found to be the most adequate model to describe the cure kinetics of the observed thermal events. Isothermal kinetic parameters are estimated using the Horie model. The onset decomposition temperature and char yield (at 700°C) of the crosslinked material were 290°C and 27%, respectively. The activation energy of the solid‐state thermal degradation process is evaluated by Ozawa approach, resulting in 95–138 kJ/mol on a range of 2–20% decomposition conversion. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1257–1265, 2006     

Synthesis,characterization, and thermal degradation kinetics of the copolymer poly(4‐methoxybenzyl methacrylate‐co‐isobornyl methacrylate)

A copolymer of 4‐methoxybenzyl methacrylate and isobornyl methacrylate was synthesized by atom transfer radical polymerization. The structure of poly(4‐methoxybenzyl methacrylate‐co‐isobornyl methacrylate) was confirmed by means of Fourier transform infrared, ¹H‐NMR, and ¹³C‐NMR techniques. The molecular weight distribution values of the copolymer were determined with gel permeation chromatography. The number‐average molecular weight and polydispersity index values of poly(4‐methoxybenzyl methacrylate‐co‐isobornyl methacrylate) were found to be 12,500 and 1.5, respectively. The kinetics of the thermal degradation of the copolymer was investigated with thermogravimetric analysis at different heating rates. The activation energy values obtained with the Kissinger, Flynn–Wall–Ozawa, and Tang methods were determined to be 166.38, 167.54, and 167.47 kJ/mol, respectively. Different integral and differential methods were used, and the results were compared with these values. Doyle approximation was also used for comparing the experimental results to master plots. An analysis of the experimental results suggested that the reaction mechanism was an R₁ deceleration type in the conversion range studied. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Curing behavior of a novolac‐type phenolic resin analyzed by differential scanning calorimetry

Curing of a novolac‐type phenolic resin was studied by DSC. The kinetic analysis was performed by means of the dynamic Ozawa method at heating rates of 5, 10, 15, and 20°C/min. This analysis was used to determine the kinetic parameters of the curing process. The activation energy was found to be 144 kJ/mol. It was found that the Ozawa exponent values decreased with increasing reaction temperature from 3.5 to 1, suggesting a change in the reaction mechanism from microgel growth to diffusion‐controlled reaction. The reaction rate constant was found to range from 123.0 to 33.6 (°C/min)ⁿ. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1678–1682, 2003     

Thermal characteristics and pyrolysis of methyl‐di(phenylethynyl)silane resin

Thermal stability of a recently synthesized polymeric methyl‐di(phenylethynyl)silane (MDPES) resin was studied using a number of thermal and spectrometric analytical techniques. The polymer exhibits extremely high thermal stability. Thermogravimetric analysis (TGA) shows that the temperature of 5% weight loss (T_d5) was 615°C and total weight loss at 800°C was 8.9%, in nitrogen atmosphere, while in air, T_d5 was found to be 562°C, and total weight loss at 800°C was found to be 55.8% of the initial weight. Differential thermal degradation (DTG) studies show that the thermal degradation of MDPES resin was single‐stage in air and two‐stage in nitrogen. The thermal degradation kinetics was studied using dynamic TGA, and the apparent activation energies were estimated to be 120.5 and 114.8 kJ/mol in air, respectively, by Kissinger and Coats–Redfern method. The white flaky pyrolysis residue was identified to be silicon dioxide by FTIR and EDS, indicating that the thermal stability of polymer may be enhanced by the formation of a thin silicon dioxide film on the material surface. © 2006 Wiley Periodicals, Inc. J Appl PolymSci 103: 605–610, 2007     

Thermal decomposition behavior of oligo(4‐hydroxyquinoline)

In this study, the kinetic parameters and reaction mechanism of decomposition process of oligo(4‐hydroxyquinoline) synthesized by oxidative polymerization were investigated by thermogravimetric analysis (TGA) at different heating rates. TGA‐derivative thermogravimetric analysis curves showed that the thermal decomposition occurred in two stages. The methods based on multiple heating rates such as Kissinger, Kim–Park, Tang, Flynn–Wall–Ozawa method (FWO), Friedman, and Kissinger–Akahira–Sunose (KAS) were used to calculate the kinetic parameters related to each decomposition stage of oligo(4‐hydroxyquinoline). The activation energies obtained by Kissinger, Kim–Park, Tang, KAS, FWO, and Friedman methods were found to be 153.80, 153.89, 153.06, 152.62, 151.25, and 157.14 kJ mol^?1 for the dehydration stage, 124.7, 124.71, 126.14, 123.75, 126.19, and 124.05 kJ mol^?1 for the thermal decomposition stage, respectively, in the conversion range studied. The decomposition mechanism and pre‐exponential factor of each decomposition stage were also determined using Coats–Redfern, van Krevelen, Horowitz–Metzger methods, and master plots. The analysis of the master plots and methods based on single heating rate showed that the mechanisms of dehydration and decomposition stage of oligo(4‐hydroxyquinoline) were best described by kinetic equations of A_n mechanism (nucleation and growth, n = 1) and D_n mechanism (dimensional diffusion, n = 6), respectively. POLYM. ENG. SCI., 54:992–1002, 2014. © 2013 Society of Plastics Engineers     

Nonisothermal curing kinetics of a novel polymer containing phenylsilylene and propargyl–hexafluorobisphenol a units

A novel thermosetting polymer, poly[(phenylsilylene) propargyl–hexafluorobisphenol A] (PBAFS), with a new structure was synthesized. The structure of PBAFS and its cured resins were characterized by Fourier transform infrared spectra. During curing, a hydrosilylation reaction may occur between Si? H and C?C bonds and a Claisen rearrangement reaction of aryl propargyl ether led to formation of chromene, which immediately preceded polymerization on heating. The dynamic viscosity behavior was investigated by rheological experiment. Thermal stability of the cured PBAFS was also measured by Thermogravimetric analysis. The curing behavior of PBAFS was monitored by nonisothermal differential scanning calorimetry at different heating rates. The kinetic parameters and the kinetic model of the cure reaction were evaluated by Kissinger, Ozawa, and Friedman methods. The cure reaction of PBAFS was found nth‐order in nature and the prediction curves by Friedman method for nonisothermal curing reaction were in good agreement with the experimental curves. The isothermal curing time of PBAFS were predicted by Vyazovkin and model‐fitting methods from the nonisothermal kinetic parameters. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Thermal Behavior and Thermolysis Kinetics of the Explosive Trans‐1,4,5,8‐Tetranitro‐1,4,5,8‐Tetraazadecalin (TNAD)

Trans‐1,4,5,8‐Tetranitro‐1,4,5,8‐Tetraazadecalin (TNAD), a cyclic nitroamine, has been studied with regard to the kinetics and mechanism of thermal decomposition, using thermogravimetry (TG), IR spectroscopy, and pressure differential scanning calorimetry (PDSC). The IR spectra of TNAD have also been recorded, and the kinetics of thermolysis has been followed by non‐isothermal TG. The activation energy of the solid‐state process was determined by using the Flynn‐Wall‐Ozawa method. Compared with the activation energy obtained from the Ozawa method, the reaction mechanism of the exothermic process of TNAD was classified by the Coats‐Redfern method as a nucleation and nuclear growth (Avrami equation 1) chemical reaction (α=0.30–0.60) and a 2D diffusion (Valensi equation) chemical reaction (α=0.60–0.90). E_a and ln A were established to be 330.14 kJ mol⁻¹ and 29.93 (α=0.30–0.60) or 250.30 kJ mol⁻¹ and 21.62 (α=0.60–0.90).     

Nonisothermal cure of bisphenol epoxy resin with a nonlinear aliphatic polyamine hardener

The amino terminated polypropylenimine dendrimer (DAB‐dendri‐(NH₂)₄) was employed as a new nonlinear aliphatic curing agent for diglycidyl ether of bisphenol A (DGEBA). Nonisothermal curing reaction kinetics of DGEBA/DAB was investigated with a differential scanning calorimeter (DSC). The apparent reaction activation energy E_a is about 56.7 kJ/mol determined using the Kissinger equation, and a two‐parameter (m, n) autocatalytic model ([icirc]Sesták–Berggren equation) was confirmed to be able to well simulate the reaction kinetics in the light of the Málek method. In addition, the relation between reaction activation energy E_a and curing degree α was obtained by applying model‐free isoconversional analysis with the Kissinger‐Akahira‐Sunose (KAS) method. As α increases, E_a reduced quickly from >80 kJ/mol to ≈60 kJ/mol up to a ≈ 15%, then decreased slowly to 55 kJ/mol till a ～ 75%, and finally dropped to 44 kJ/mol at full conversion. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of heat‐resistant N‐phenylmaleimide–styrene–maleic anhydride copolymers and application in acrylonitrile–butadiene–styrene resin

The heat‐resistant copolymer of N‐phenylmaleimide (NPMI)–styrene (St)–maleic anhydride (MAH) was synthesized in xylene at 125°C with di‐tert‐butyl diperoxyterephthalate as an initiator. The characteristics of the copolymer were analyzed by Fourier transform infrared spectroscopy, nuclear magnetic resonance spectroscopy (¹H‐NMR and ¹³C‐NMR), gel permeation chromatography, and elemental analysis. The ¹³C‐NMR results show that the copolymer possessed random sequence distribution; this was also supported by the differential scanning calorimetry experiment, in which a single glass‐transition temperature (T_g) of 202.3°C was observed. The thermal stability and degradation mechanism of the copolymer were investigated by thermogravimetric analysis. Using the Kissinger equation and Ozawa equation, we proved a nucleation controlling mechanism with an apparent activation energy of 144 kJ/mol. Blends of acrylonitrile–butadiene–styrene with the NPMI–St–MAH copolymer with various contents were prepared with a twin‐screw extruder processes. The mechanical and thermal properties of the materials, such as the tensile and flexural strength, T_g's, and Vicat softening temperatures, were all enhanced with the addition of the modifier, whereas the melt flow index decreased. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Curing behavior of epoxy resins in two‐stage curing process by non‐isothermal differential scanning calorimetry kinetics method

In this research, a new thermal curing system, with two‐stage curing characteristics, has been designed. And the reaction behaviors of two different curing processes have been systematically studied. The non‐isothermal differential scanning calorimetry (DSC) test is used to discuss the curing reaction of two stages curing, and the data obtained from the curves are used to calculate the kinetic parameters. Kissinger‐Akahira‐Sunose (KAS) method is applied to determine activation energy (E_a) and investigate it as the change of conversion (α). Málek method is used to unravel the curing reaction mechanism. The results indicate that the curing behaviors of two different curing stages can be implemented successfully, and curing behavior is accorded with ?esták‐Berggren mode. The non‐isothermal DSC and Fourier transform infrared spectroscopy test results reveal that two different curing stages can be implemented successfully. Furthermore, the double x fitting method is used to determine the pre‐exponential factor (A), reaction order (m, n), and establish the kinetic equation. The fitting results between experiment curves and simulative curves prove that the kinetic equation can commendably describe the two different curing reaction processes. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40711.     

Cure kinetics and catalyzed effect of hydroxyl group of LC diglycidyl ether of bisphenol‐S with aromatic diamines

The curing reactions of liquid crystalline 4,4′‐bis‐(2,3‐epoxypropyloxy)‐sulfonyl‐bis(1,4‐phenylene) (p‐BEPSBP) with 4,4′‐diaminodiphenylmethane (DDM) and 4,4′‐diaminodiphenylsulfone (DDS) were investigated by nonisothermal differential scanning calorimeter (DSC). The relationships of E_a with the conversion α in the curing process were determined. The catalyzed activation of hydroxyl group for curing reaction of epoxy resins with amine in DSC experiment was discussed. The results show that these curing reactions can be described by the autocatalytic ?esták‐Berggren model. The curing technical temperature and parameters were obtained, and the even reaction orders m, n, and ΔS for p‐BEPSBP/DDM and p‐BEPSBP/DDS are 0.35, 0.92, ?81.94 and 0.13, 1.32, ?24.45, respectively. The hydroxyl group has catalyzed activation for the epoxy–amine curing system in the DSC experiment. The average E_a of p‐BEPSBP/DDM is 67.19 kJ mol^?1 and is 105.55 kJ mol^?1 for the p‐BEPSBP/DDS system, but it is different for the two systems; when benzalcohol as hydroxyl group was added to the curing system, the average E_a of p‐BEPSBP/DDM decreases and increases for p‐BEPSBP/DDS. The crystalline phase had formed in the curing process and was fixed in the system. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

A novel imidazole derivative curing agent for epoxy resin: Synthesis,characterization, and cure kinetic

A novel imidazole derivative (named as EMI‐g‐BGE) was synthesized through the reaction of 2‐ethyl‐4‐methyl imidazole (EMI) and butyl glycidyl ether (BGE) and characterized by elemental analysis, FTIR spectroscopy, and ¹H NMR spectroscopy. The curing kinetic of diglycidyl ether of bisphenol A (DGEBA) epoxy resin with EMI‐g‐BGE as curing agent was studied by nonisothermal DSC technique at different heating rates. Dynamic DSC scans indicated that EMI‐g‐BGE was an effective curing agent of epoxy resin. The apparent activation energy E_a was 71.8 kJ mol^?1 calculated through Kissinger method, and the kinetic parameters were determined by Málek method for the kinetic analysis of the thermal treatment obtained by DSC measurement. A two‐parameter (m, n) autocatalytic model (?esták‐Berggren equation) was found to be the most adequate selected kinetic model. In addition, the predicted curves from the kinetic model fit well with the nonisothermal DSC thermogram. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Evaluation of nonisothermal crystallization kinetic models for linear poly(phenylene sulfide)

The nonisothermal crystallization kinetics of linear Poly(phenylene sulfide) (PPS) was studied with differential scanning calorimetry. Ozawa theory, Jeziorny model, and Mo equation were applied to describe the crystallization kinetics and to determine the crystallization parameters and mechanism of the linear PPS resin. The crystallization activation energies were also calculated using Kissinger formula and Flynn‐Wall‐Ozawa equation, respectively. According to the Ozawa model, it is found that instantaneous nucleation takes place during crystallization of PPS; the Ozawa exponent m is 3 in initial stage of crystallization; as the crystallization temperature decreases, the value of m reduces, and the growth rate of crystal almost keeps a constant. The Avrami exponent n obtained from Jeziorny model fluctuate around 1.84. Based on the Jeziorny model, the crystallization rate increases with increasing the cooling rate, but it does not change any longer when the cooling rate rise to a certain value. Mo equation also exhibits great advantages in treating the nonisothermal crystallization kinetics of PPS. The activation energy E of nonisothermal crystallization process of PPS is calculated to be −162.73 kJ/mol by the Kissinger formula, and the mean value of E determined by Flynn‐Wall‐Ozawa equation is −152.40 kJ/mol. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Curing behavior and thermal properties of multifunctional epoxy resin with methylhexahydrophthalic anhydride

The curing behavior and thermal properties of bisphenol A type novolac epoxy resin (bisANER) with methylhexahydrophthalic anhydride (MHHPA) at an anhydride/epoxy group ratio of 0.85 was studied with Fourier‐transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), and thermogravimetry. The results showed that the FTIR absorption intensity of anhydride and epoxide decreased during the curing reaction, and the absorption peak of ester appeared. The dynamic curing energies were determined as 48.5 and 54.1 kJ/mol with Kissinger and Flynn–Wall–Ozawa methods, respectively. DSC measurements showed that as higher is the curing temperature, higher is the glass transition. The thermal degradation of the cured bisANER/MHHPA network was identified as two steps: the breaking or detaching of ? OH, ? CH₂? , ? CH₃, OC? O and C? O? C, etc., taking place between 300 and 450°C; and the carbonizing or oxidating of aromatic rings occurring above 450°C. The kinetics of the degradation reaction was studied with Coats–Redfern method showing a first‐order process. In addition, vinyl cyclohexene dioxide (VCD) was employed as a reactive diluent for bisANER (VCD/bisANER = 1 : 2 w/w) and cured with MHHPA, and the obtained network had a higher T_g and a slight lower degradation temperature than the undiluted system. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2041–2048, 2007