Surface tearing and wall slip phenomena in extrusion of highly filled HDPE/wood flour composites

The extrudate surface tearing of highly filled high‐density polyethylene (HDPE)/wood flour composites has been investigated in relation to the rheological properties and the wall slip phenomenon in capillary dies. Rotational and capillary rheometers were employed to measure the rheological properties. Mooney analysis was used for determination of wall slip velocity. The results showed considerable increase of storage modulus, dynamic and shear viscosity with increasing wood flour loading. It was also found that all wood filled composites did not obey the Cox–Merz rule. The wall slip velocity depends on wood filler content and shear rate. Generally, with increasing shear rate the slip velocity sharply increases leading to plug‐like flow. It was observed that the surface of the extrudates becomes smoother with increase in shear rate and wood flour content. POLYM. ENG. SCI., 46:1204–1214, 2006. © 2006 Society of Plastics Engineers     

Effect of filler treatments on rheological behavior of calcium carbonate and talc‐filled polypropylene hybrid composites

Commercial stearic acid treated calcium carbonate (CaCO₃) was used to make a comparative study on rheological behavior of the CaCO₃ and talc‐filled polypropylene (PP) hybrid composites with nontreated filler. Apparent shear viscosity and extrudate swell were investigated with variation of filler ratio and temperature with 30% by weight total of filler was used in PP composite. The Shimadzu capillary rheometer was used to evaluate shear viscosity and shear rate of the composite. It was found that the shear viscosities decrease with increasing shear rate. The apparent shear viscosity of the composite containing the stearic acid treated is slightly lower than untreated filler. Shear thickening behavior at higher shear rate has also shown by 15/15 treated composites at higher temperature about 220°C and investigation by SEM has proved that filler being densely packed at that condition. Treated composites also exhibit lower swelling ratio value than untreated composite, and swelling ratio also decreases linearly with increasing temperature and the die length–diameter ratio. It is believed that dispersion of filler play an important role not only on shear viscosity but also on swelling ratio of PP composite. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5421–5426, 2006     

Wood‐fiber‐reinforced poly(lactic acid) composites: Evaluation of the physicomechanical and morphological properties

This article presents the results of a study of the processing and physicomechanical properties of environmentally friendly wood‐fiber‐reinforced poly(lactic acid) composites that were produced with a microcompounding molding system. Wood‐fiber‐reinforced polypropylene composites were also processed under similar conditions and were compared to wood‐fiber‐reinforced poly(lactic acid) composites. The mechanical, thermomechanical, and morphological properties of these composites were studied. In terms of the mechanical properties, the wood‐fiber‐reinforced poly(lactic acid) composites were comparable to conventional polypropylene‐based thermoplastic composites. The mechanical properties of the wood‐fiber‐reinforced poly(lactic acid) composites were significantly higher than those of the virgin resin. The flexural modulus (8.9 GPa) of the wood‐fiber‐reinforced poly(lactic acid) composite (30 wt % fiber) was comparable to that of traditional (i.e., wood‐fiber‐reinforced polypropylene) composites (3.4 GPa). The incorporation of the wood fibers into poly(lactic acid) resulted in a considerable increase in the storage modulus (stiffness) of the resin. The addition of the maleated polypropylene coupling agent improved the mechanical properties of the composites. Microstructure studies using scanning electron microscopy indicated significant interfacial bonding between the matrix and the wood fibers. The specific performance evidenced by the wood‐fiber‐reinforced poly(lactic acid) composites may hint at potential applications in, for example, the automotive and packaging industries. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4856–4869, 2006     

Effects of silane coupling agent and maleic anhydride‐grafted polypropylene on the morphology and viscoelastic properties of polypropylene–mica composites

In this study, morphology, and dynamic and mechanical properties of polypropylene–mica (PP–Mica) composites were investigated. To enhance the adhesion between PP and mica, maleic anhydride‐grafted PP (MAPP) and treated mica with silane coupling agent were used. MAPP (as a compatibilizer) and silane coupling agent (as a filler surface modifier) caused an interfacial bonding in the mica filled polypropylene composites. The effect of mica content, MAPP, and treated mica with silane coupling agent on the morphological properties were investigated by Scanning Electron Microscopy (SEM). The results showed that with increasing MAPP or silane coupling agent, dispersion of filler and adhesion between PP and filler were improved. Mechanical data showed that with increasing MAPP and mica treated with silane coupling agent, tensile modulus and flextural strength of composites were enhanced. Dynamic rheological behavior of composites was also investigated within the domain of linear viscoelasticity. The rheological observations indicated that the complex viscosity, storage and loss moduli increased, and tan δ decreased with increasing mica content. POLYM. COMPOS. 27:491–496, 2006. © 2006 Society of Plastics Engineers.     

Damping behavior of wood filled polypropylene composites

The damping coefficient (tanδ) of wood flour filled polypropylene composites, having varying filler concentrations were measured using the free vibration decay of disk‐shaped specimen, vibrating in flexural vibration mode. The damping coefficients decreased with the increase of filler load in composites. There was no significant difference in damping behavior of composites with and without compatiblizer at low filler level (upto 30%). At higher filler loading (>30%), composites with compatiblizer had lower damping coefficient suggesting improved interfacial adhesion between wood and polypropylene. The damping in composite is attributed to the damping because of the composite constituents and damping at the interface. The damping because of interface was estimated using a model and was found to increase with the increase in filler loading. At higher filler content, damping due to interface in composites with compatiblizer was significantly lower than in composites without compatiblizer suggesting a better interfacial adhesion between the wood filler and polypropylene matrix with compatiblizer. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Mechanical and tribological properties of glass–epoxy composites with and without graphite particulate filler

The objectives of this research article is to evaluate the mechanical and tribological properties of glass‐fiber‐reinforced epoxy (G–E) composites with and without graphite particulate filler. The laminates were fabricated by a dry hand layup technique. The mechanical properties, including tensile strength, tensile modulus, elongation at break, and surface hardness, were investigated in accordance with ASTM standards. From the experimental investigation, we found that the tensile strength and dimensional stability of the G–E composite increased with increasing graphite content. The effect of filler content (0–7.5 wt %) and sliding distance on the friction and wear behavior of the graphite‐filled G–E composite systems were studied. Also, conventional weighing, determination of the coefficient of friction, and examination of the worn surface morphological features by scanning electron microscopy (SEM) were done. A marginal increase in the coefficient of friction with sliding distance for the unfilled composites was noticed, but a slight reduction was noticed for the graphite‐filled composites. The 7.5% graphite‐filled G–E composite showed a lower friction coefficient for the sliding distances used. The wear loss of the composites decreased with increasing weight fraction of graphite filler and increased with increasing sliding distance. Failure mechanisms of the worn surfaces of the filled composites were established with SEM. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2472–2480, 2007     

An investigation on the mechanical and dynamic rheological properties of single and hybrid filler/polypropylene composites based on talc and calcium carbonate

Some results of experiments on the mechanical and rheological properties of mineral filled polypropylene were presented. Single filler and hybrid filler composites of talc and calcium carbonate (CaCO₃) were prepared in a co‐rotating twin‐screw extruder. The effect of filler type, filler content, and coupling agent on the mechanical and rheological properties of the polypropylene were studied. The coupling agent was maleic anhydride‐grafted polypropylene (PP‐g‐MA). It was found that the mechanical properties are affected by filler type, filler concentration, and the interaction between filler and matrix. The tensile strength of the composite is more affected by the talc while the impact strength is influenced mostly by CaCO₃ content. The elongation at break of PP/CaCO₃ composites was higher than that of PP/talc composites. The incorporation of coupling agent into PP/mineral filler composites increased the mechanical properties. Rheological properties indicated that the complex viscosity and storage modulus of talc filled samples were higher than those of calcium carbonate filled samples while the tan δ was lower. The rheological properties of hybrid‐filler filled sample were more affected by the talc than calcium carbonate. The PP‐g‐MA increased the complex viscosity and storage modulus of both single and hybrid composites. POLYM. COMPOS., 2009. © 2009 Society of Plastics Engineers     

Influence of Electron Beam Irradiation on High‐Temperature Mechanical Properties of Ethylene Vinyl Acetate/Carbon Fibers Composites

The purpose of this study was to investigate the effect of carbon fiber (CF) and electron‐beam (EB) radiation on high‐temperature mechanical properties of ethylene‐vinyl acetate (EVA). Polymer composites were prepared by mixing on a two‐roll mill. After compression molding, the samples were irradiated between 60 and 180 kGy, and dynamic mechanical analysis (DMA) was used to characterize physical properties. The effects of filler content and radiation level on the mechanical properties of EVA/CF were evaluated. The shear stress and modulus were observed to increase with increasing of the filler level. However, there was a dramatic decrease in creep compliance. It was also shown that introduction of irradiation on EVA composite increases the shear stress and the real part of the dynamic shear modulus G' due to the increase in molecular weight and cross‐linking of the polymer after irradiation. J. VINYL ADDIT. TECHNOL., 26:325–335, 2020. © 2019 Society of Plastics Engineers     

Sugar palm fiber/polyester nanocomposites: Influence of adding nanoclay fillers on thermal,dynamic mechanical,and physical properties

In this research, nanoclay used as filler in sugar palm‐reinforced composites was investigated by the physical, thermal, and dynamic mechanical properties. Various concentrations of nanoclay were used to fabricate composites by using hand lay‐up technique, followed by hot compression molding with naturally woven sugar palm fiber‐reinforced in polyester matrix. Among various weight concentrations such as 1–5% of nanoclay, it was found that 2% nanoclay‐filled composite (NC) demonstrated the best balance of thermomechanical properties and significantly enhanced the composite. DMA demonstrated that 2% nanoclay content resulted in improved viscoelastic behavior and higher glass transition temperature (T_g) of the composites. TGA also showed improvement in properties, whereas 3% nanoclay‐filled composite showed superior onset temperature, and 5% nanoclay‐filled composite exhibited highest remaining residue. The nanoclay filler was very effective to fill the porous structure and maintain the thickness stability. The thickness swelling was reduced with increasing amount of nanoclay in composites. Overall, the addition of nano clay improved thermal and physical properties of sugar palm‐reinforced polyester composite. J. VINYL ADDIT. TECHNOL., 26:236–243, 2020. © 2019 Society of Plastics Engineers     

Study of plastic compounds containing polypropylene and wood derived fillers from waste of different origin

The scope of the article was to study the perspectives of the using of wood derived fillers (WDF) from waste of different origin as fillers of polypropylene. The WDF used in this study was hard wood flour (HW), birch veneer polishing dust (VD) and tetra‐pack carton cellulose fiber (TC). Some mechanical strength parameters, water uptake in the static and cyclic test and resistance to fungal decay of polypropylene (PP) composites containing these three types of WDF were studied and compared with similar loading (40 wt %) talc‐filled PP. Composites containing TC and VD fibers as filler showed the highest flexural strength at three test temperatures (?40, +20, and +40°C) and flexural modulus and tensile strength at plus temperatures. On the other hand talc‐filled PP exhibited greatest flexural modulus at minus temperature, greatest impact strength at room temperature and best flow ability. Significant difference was observed between PP composites with HW and VD fillers regarding water uptake in cyclic tests, however flexural strength and modulus change of composites were reversible after drying. No weight loss of WDF/PP composites was observed after 6 week exposure to brown‐ and white‐rot fungi, however, degradation of the surface of samples was detected by SEM. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of natural fibers on thermal and mechanical properties of natural fiber polypropylene composites studied by dynamic mechanical analysis

The present study deals with the effects of natural fibers on thermal and mechanical properties of natural fiber polypropylene composites using dynamic mechanical analysis. Composites of polypropylene and various natural fibers including kenaf fibers, wood flour, rice hulls, and newsprint fibers were prepared at 25 and 50% (by weight) fiber content levels. One and two percent maleic anhydride grafted polypropylene was also used as the compatibilizer for composites containing 25 and 50% fibers, respectively. Specimens for dynamic mechanical analysis tests were cut out of injection‐molded samples and were tested over a temperature range of ?60 to +120°C. Frequency of the oscillations was fixed at 1 Hz and the strain amplitude was 0.1%, which was well within the linear viscoelastic region. The heating rate was 2°C/min for all temperature scan tests. Storage modulus (E′), loss modulus (E″), and mechanical loss factor (tan δ) were collected during the test and were plotted versus temperature. An increase in storage and loss moduli and a decrease in the mechanical loss factor were observed for all composites indicating more elastic behavior of the composites as compared with the pure PP. Changes in phase transition temperatures were monitored and possible causes were discussed. Results indicated that glass transition was slightly shifted to lower temperatures in composites. α transition temperature was higher in the case of composites and its intensity was higher as well. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4341–4349, 2006     

Structure and properties of UHMWPE fiber/carbon fiber hybrid composites

Ultrahigh molecular weight polyethylene (UHMWPE) fiber/carbon fiber hybrid composites were prepared by inner‐laminar and interlaminar hybrid way. The mechanical properties, dynamic mechanical analysis (DMA), and morphologies of the composites were investigated and compared with each other. The results show that the hybrid way was the major factor to affect mechanical and thermal properties of hybrid composites. The resultant properties of inner‐laminar hybrid composite were better than that of interlaminar hybrid composite. The bending strength, compressive strength, and interlaminar shear strength of hybrid composites increased with an increase in carbon fiber content. The impact strength of inner‐laminar hybrid composite was the largest (423.3 kJ/m²) for the UHMWPE fiber content at 43 wt % to carbon fiber. The results show that the storage modulus (E′), dissipation factor (tan δ), and loss modulus (E″) of the inner‐laminar hybrid composite shift toward high temperature remarkably. The results also indicate that the high‐performance composite with high strength and heat resistance may be prepared by fibers' hybrid. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1880–1884, 2006     

Electrical conductivity and rheology of carbon‐filled liquid crystal polymer composites

One emerging market for electrically conductive resins is for bipolar plates for use in fuel cells. Adding carbon fillers to thermoplastic resins increases composite electrical conductivity and viscosity. Current technology often adds as much of a single type of carbon filler as possible to achieve the desired conductivity, while still allowing the carbon‐filled thermoplastic matrix material to be extruded and molded into a bipolar plate. In this study, varying amounts of two different types of carbon, one carbon black and one synthetic graphite, were added to Vectra A950RX liquid crystal polymer. The resulting single filler composites were then tested for electrical conductivity and rheological properties. The electrical conductivity followed that typically seen in polymer composites with a percolation threshold at 4 vol % for carbon black and at 15 vol % for synthetic graphite. Over the range of shear rates studied, the viscosity followed a shear‐thinning power law model with power‐law exponent (n ? 1) = ?0.5 for neat Vectra A950RX and (n ? 1) = ?0.7 for highly filled composite materials. Viscosity increased with increasing filler volume fraction for all shear rates. The viscosity–enhancement effect was more rapid for the composites containing carbon black when compared with those containing synthetic graphite. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2680–2688, 2006     

Rheological characterization of PP/jute composite melts

The present article summarizes an experimental study on the molten viscoelastic behavior of PP/jute composites under steady and dynamic mode. Variations in melt viscosity and die swell of the composites with an increase in shear rate, fiber loading, and coupling agent concentration have been investigated using capillary rheometer. It was observed that with the addition of fibers and MAPP, the melt viscosity of the composites increased due to improved fiber‐matrix interfacial adhesion. Further, the dynamic viscoelastic behavior, measured using parallel plate rheometer, revealed an increase in the storage modulus (G′), indicating higher stiffness in case of fiber‐filled composites as compared with the virgin matrix. Time–temperature superposition was applied to generate various viscoelastic master curves. The fiber‐matrix morphology of the extrudates was also examined using scanning electron microscopy, which corroborated the findings of rheological properties. The treated composites displayed uniform distribution of fibers within the PP matrix with lesser surface irregularities. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1476–1484, 2006     

Polypropylene cellulose‐based composites: The effect of bagasse reinforcement and polybutadiene isocyanate treatment on the mechanical properties

Using bagasse fiber as the reinforcing filler and polypropylene as the thermoplastic matrix polymer, a reinforced composite was prepared, and its mechanical properties examined as a function of the amount of compatibilizing agents used. In the sample preparation, four levels of fiber loading (10, 20, 30, and 40 wt %), three levels of polybutadiene isocyanate (PBNCO) content (0, 2, and 4 wt %) and two levels of maleated polypropylenes (MAPP) content (0 and 3 wt %) as compatibilizing agents were used. The tensile properties of the composites improved as the fiber loading and the compatibilizing agents increased, but the impact strength was significantly decreased. The mechanical study revealed that the positive effect of compatibilizing agents on interfacial bonding. The composites treated with PBNCO showed superior tensile and impact properties than those without treatment. The findings indicated that bagasse as agro‐waste material is a valuable renewable natural resource for composite production and could be utilized as a substitute for wood in composite industries. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

The use of Isocyanate as a Bonding Agent to Improve the Mechanical Properties of Polyethylene-Wood Fiber Composites

Abstract

Chemithermomechanical pulp (CTMP) of aspen was used as a filler in high density (HDPE) and linear low density (LLDPE) polyethylenes. To improve the bonding between the fiber and polymer, different chemical treatments of the fiber a) treatment with different isocyanates b) coating with maleic anhydride was carried out. Composites with isocyanate treated wood fibers produced higher tensile strength compared to untreated fiber composites. But when compared to diisocyanate, the polyisocyanate treated fibers produced higher gain in strength. HDPE or LLDPE filled with maleic anhydride coated CTMP aspen fibers showed a slight decrease in strength with the increase in filler concentration. Tensile modulus generally increased with filler loading and was not much affected by fiber treatment.     

Enhancement of mechanical properties of high modulus polypropylene grade for multilayer sewage pipes applications

Advances in technology have provided fresh generations of stiff polypropylene block copolymers for gravity sewerage applications. The aim of this study is to further enhance the stiffness of these materials through the incorporation of inorganic fillers. In this study, three talc filled PP and one glass fiber filled PP composites were characterized in order to be used as a middle layer in a three-layer sewage pipe. The obtained results showed an increase of approximately more than 100% and 250% in tensile and flexural moduli by the use of 30%–50 wt% talc-filled PP and 30 wt.% glass fiber-filled PP, respectively. This high increase in the rigidity of the material would allow manufacturing pipes with improving ring stiffness. Composites filled with 30 wt% talc or glass fiber showed good filler-matrix interaction and good filler distribution and dispersion. However, reduced filler-matrix interaction was observed in the case of the composite filled with 50 wt% talc. In addition, the use of Differential Scanning Calorimetry analysis revealed that the addition of fillers enhanced the crystallization temperature of the polypropylene matrix. Furthermore, Thermogravimetric Analysis showed that the high modulus PP grade retained its thermal stability in the various composites.     

Effects of filler–filler and polymer–filler interactions on rheological and mechanical properties of HDPE–wood composites

High‐density polyethylene (HDPE)–wood composite samples were prepared using a twin‐screw extruder. Improved filler–filler interaction was achieved by increasing the wood content, whereas improved polymer–filler interaction was obtained by adding the compatibilizer and increasing the melt index of HDPE, respectively. Then, effects of filler–filler and polymer–filler interactions on dynamic rheological and mechanical properties of the composites were investigated. The results demonstrated that enhanced filler–filler interaction induced the agglomeration of wood particles, which increased the storage modulus and complex viscosity of composites and decreased their tensile strength, elongation at break, and notched impact strength because of the stress concentration. Stronger polymer–filler interaction resulted in higher storage modulus and complex viscosity and increased the tensile and impact strengths due to good stress transfer. The main reasons for the results were analyzed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Use of construction and demolition wastes as mineral fillers in hybrid wood–polymer composites

The recycling of construction materials has been the subject of much research in past years. In this study, the use of construction and demolition wastes (CDWs) as mineral fillers in hybrid wood–polymer composites was studied. Two types of waste materials were used as fillers in the composites: (1) a mixture consisting of waste mineral wool (MW) and plasterboard (PB) and (2) mixed CDWs. The performance of the composites was evaluated from their mechanical properties and water‐absorption behavior. We found in the study that the addition of mineral fillers decreased the flexural strength and modulus values of the wood–polypropylene (PP) composites. On the other hand, the exchange of part of the wood with a mineral filler resulted in an increase in the impact strength of the composite. The composite manufactured with the combination of MW and PB had the lowest water absorption. The decrease in wood loading resulted in improved dimensional stability in the hybrid wood–mineral filler–PP composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43412.     

Mechanical and thermal properties of toughened polypropylene composites

The mechanical, thermal, and structural properties of a new flexible composite containing polypropylene fiber (PP) in a random poly(propylene‐co‐ethylene) (PPE) matrix with ethylene–propylene elastomer (EP) was investigated with emphasis on the effect of EP elastomer concentration. The intrinsic composition of the composites, toughening of the matrix with EP and the fiber–matrix interface determined the properties of the composites. Through the incorporation of EP elastomer into the polypropylene–poly (propylene‐co‐ethylene) (all‐PP) composite, tensile and storage modulus (E′) decreased, flexural modulus and loss modulus (E″, damping) increased slightly to 0.15 EP and then decreased. There was an increase in impact resistance for the toughened composites, with about 100% increase in comparison with an untoughened all‐PP composite. The composition corresponding to 0.20 weight fraction EP gave optimum impact and mechanical properties. Creep resistance of the composite decreased with increasing EP content, but recovery showed an increase with increasing EP content up to 0.20. Fracture surfaces of composites after impact tests were studied with scanning electron microscopy. Moreover, the use and limitation of theoretical equations to predict the tensile and flexural modulus of the flexible PP composite is discussed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007