Studies on the electromagnetic interference shielding effectiveness of metallized PVAc‐AgNO3/PET conductive films

A metal chelate polymer (MCP) of PVAc‐AgNO₃ was prepared by adding AgNO₃ salts into the PVAc matrix and was coated on to PET substrate to form PVAc‐AgNO₃/PET films. These films were then treated with NaBH₄ aqueous solution to become the reduced metallized conductive films (RMCF) of PVAc‐AgNO₃/PET. The electromagnetic interference shielding effectiveness (EMI/SE) and the characteristics of these films were investigated. The SE value was measured by the far‐field transmission line method. The surface resistivity (Rs) of RMCF with a AgNO₃ content of 15 wt % was found to be below 5 Ω/sq, and the SE value exceeded 20 dB over the frequency range 50–900 MHz. The Rs of RMCF with a AgNO₃ content of 30 wt % was less than 1 Ω/sq, and the SE value even reached 33 dB at 550–650 MHz. It was confirmed by X‐ray and scanning electronmicroscope (SEM) analysis that the conducting network, as formed by closely deposited silver atoms on the reduced coating surface, was the dominant pathway for effective electron propagation that contributed to the excellent conductivity of these RMCF (PVAc‐AgNO₃/PET). © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 270–273, 2004     

High‐resolution solid‐state NMR and SEM study of the interaction behavior of poly(ethylene‐co‐vinyl acetate)/poly(vinyl acetate) blends

Binary blends formed by two types of ethylene‐co‐vinyl acetate (EVA), which have different vinyl acetate contents, and poly(vinyl acetate) (PVAc) were prepared in a Haake Rheocord 9000 plastograph. A series of samples were obtained varying the PVAc amount up to 50%. The studies were carried out employing solid‐state nuclear magnetic resonance spectroscopy (NMR) and scanning electronic microscopy (SEM). The xenon‐129 (¹²⁹Xe) and carbon‐13 (¹³C) NMR response together with the microscopy results showed that the systems are heterogeneous. Therefore, EVA with a higher vinyl acetate content presented some interaction between the polymer blend components. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 116–124, 2002     

Preparation and Characterization of Gelatin Nanofibers Containing Silver Nanoparticles

Ag nanoparticles (NPs) were synthesized in formic acid aqueous solutions through chemical reduction. Formic acid was used for a reducing agent of Ag precursor and solvent of gelatin. Silver acetate, silver tetrafluoroborate, silver nitrate, and silver phosphate were used as Ag precursors. Ag⁺ ions were reduced into Ag NPs by formic acid. The formation of Ag NPs was characterized by a UV-Vis spectrophotometer. Ag NPs were quickly generated within a few minutes in silver nitrate (AgNO₃)/formic acid solution. As the water content of formic acid aqueous solution increased, more Ag NPs were generated, at a higher rate and with greater size. When gelatin was added to the AgNO₃/formic acid solution, the Ag NPs were stabilized, resulting in smaller particles. Moreover, gelatin limits further aggregation of Ag NPs, which were effectively dispersed in solution. The amount of Ag NPs formed increased with increasing concentration of AgNO₃ and aging time. Gelatin nanofibers containing Ag NPs were fabricated by electrospinning. The average diameters of gelatin nanofibers were 166.52 ± 32.72 nm, but these decreased with the addition of AgNO₃. The average diameters of the Ag NPs in gelatin nanofibers ranged between 13 and 25 nm, which was confirmed by transmission electron microscopy (TEM).     

Poly(acrylonitrile‐co‐vinyl acetate)/Ag composite microspheres: One‐pot fabrication and application as catalyst

Waxberry‐like poly(acrylonitrile‐co‐vinyl acetate)/Ag composite microspheres have been prepared simply and directly via a one‐step self‐assembly approach. The morphology, formation, and catalytic activity of the as‐prepared composite microspheres are further investigated. The difference in the solubility among different segments of poly(acrylonitrile‐co‐vinyl acetate) is the basis of the formation of poly(acrylonitrile‐co‐vinyl acetate) microspheres, while the ? CN groups on the surface of poly(acrylonitrile‐co‐vinyl acetate) microspheres play an important role in the growth process from poly(acrylonitrile‐co‐vinyl acetate) microsphere to poly(acrylonitrile‐co‐vinyl acetate)/Ag composite microsphere. It is found that bulk quantities of composite microspheres with high density of Ag nanoparticles on the surface can be obtained readily by controlling the concentration of AgNO₃. The as‐prepared composite microsphere exhibits excellent catalytic activity on reduction of p‐nitrophenol. This study may shed some light on the self‐assembly of other metal/polymer composite microspheres. POLYM. ENG. SCI., 50:1767–1772, 2010. © 2010 Society of Plastics Engineers     

Synthesis and characterization of poly(vinyl chloride‐co‐vinyl acetate)‐graft‐poly[(meth)acrylates] by atom transfer radical polymerization

The graft polymerization of methyl methacrylate and butyl acrylate onto poly(vinyl chloride‐co‐vinyl acetate) with atom transfer radical polymerization (ATRP) was successfully carried out with copper(I) thiocyanate/N,N,N′,N′,N″‐pentamethyldiethylenetriamine and copper(I) chloride/2,2′‐bipyridine as catalysts in the solvent N,N‐dimethylformamide. For methyl methacrylate, a kinetic plot of ln([M]₀/[M]) (where [M]₀ is the initial monomer concentration and [M] is the monomer concentration) versus time for the graft polymerization was almost linear, and the molecular weight of the graft copolymer increased with increasing conversion, this being typical for ATRP. The formation of the graft polymer was confirmed with gel permeation chromatography, ¹H‐NMR, and Fourier transform infrared spectroscopy. The glass‐transition temperature of the copolymer increased with the concentration of methyl methacrylate. The graft copolymer was hydrolyzed, and its swelling capacity was measured. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 183–189, 2005     

Synthesis and characterization of novel silver/L‐phenylalanine‐based optically active polyacrylate nanocomposite

Novel bioactive and optically active poly(N‐acryloyl‐L ‐phenylalanine) (PAPA) was synthesized by atom transfer radical polymerization. PAPA‐silver (Ag) nanocomposites have been successfully prepared via in situ reducing Ag⁺ ions anchored in the polymer chain using hydrazine hydrate as reducing agent in an aqueous medium. By controlling of the amount of Ag⁺ ions introduced, we have produced an organic/inorganic nanocomposite containing Ag nanoparticles with well controlled size. Nanocomposites were characterized by X‐ray diffraction (XRD), UV–Vis spectrophotometry, transmission electron microscopy, and Fourier transform infrared. XRD pattern showed presence of Ag nanoparticles. The PAPA/Ag nanocomposites with 1 : 10 silver nitrate (AgNO₃) : PAPA ratio revealed the presence of well‐dispersed Ag nanoparticles in the polymer matrix. All of these Ag nanoparticles formed are spherical and more than 80% of them are in the range of 15–25 nm. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Characterization of grafting in the emulsion polymerization of vinyl acetate using poly(vinyl alcohol) as stabilizer

Emulsion polymerizations of vinyl acetate (VAc) with polyvinyl alcohol (PVA) as emulsifier were carried out by both batch and semicontinuous processes. The extent of grafting of vinyl acetate onto the PVA chains was investigated by a new method for separating the various polymer fractions in high solids content latexes. The quantification was carried out by a three‐step separation and selective solubilization of the PVAc latexes. After the separation, the water‐soluble PVA and the solvent‐soluble PVAc components were characterized by gel permeation chromatography and ¹³C–NMR, from which the accuracy of this method was verified. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1739–1747, 2001     

Preparation of high‐molecular‐weight poly(vinyl alcohol) with high yield by solution polymerization of vinyl acetate in methanol using 4,4′‐azobis(4‐cyanovaleric acid)

Vinyl acetate (VAc) was solution‐polymerized at 40°C and 50°C using 4,4′‐azobis(4‐cyanovaleric acid) (ACVA) as an initiator and methanol as a solvent, and effects of polymerization temperature and initiator concentration were investigated in terms of conversion of VAc into poly (vinyl acetate) (PVAc), degree of branching (DB) for acetyl group of PVAc, and molecular weights of PVAc and resulting poly(vinyl alcohol) (PVA) obtained by saponifying with sodium hydroxide. Slower polymerization rate by adopting ACVA and lower viscosity by methanol proved to be efficient in obtaining linear high‐molecular‐weight (HMW) PVAc with high conversion and HMW PVA. PVA having maximum number–average degree of polymerization (P_n) of 4300 could be prepared by the saponification of PVAc having maximum P_n of 7900 polymerized using ACVA concentration of 2 × 10^?5 mol/mol of VAc at 40°C. Moreover, low DB of below 1 could be obtained in ACVA system, nevertheless of general polymerization temperatures of 40°C and 50°C. This suggests an easy way for producing HMW PVA with high yield by conventional solution polymerization without using special methods such as low‐temperature cooling or irradiation. © 2006 Wiley Periodicals, Inc. J Appl PolymSci 102: 4831–4834, 2006     

Atom transfer radical polymerization of methyl methacrylate initiated with a macroinitiator of poly(vinyl acetate)

Well‐defined poly(vinyl acetate‐b‐methyl methacrylate) block copolymers were successfully synthesized by the atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) in p‐xylene with CuBr as a catalyst, 2,2′‐bipyridine as a ligand, and trichloromethyl‐end‐grouped poly(vinyl acetate) (PVAc–CCl₃) as a macroinitiator that was prepared via the telomerization of vinyl acetate with chloroform as a telogen. The block copolymers were characterized with gel permeation chromatography, Fourier transform infrared, and ¹H‐NMR. The effects of the solvent and temperature on ATRP of MMA were studied. The control over a large range of molecular weights was investigated with a high [MMA]/[PVAc–CCl₃] ratio for potential industry applications. In addition, the mechanism of the polymerization was discussed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1089–1094, 2006     

Synthesis of poly(vinyl acetate)‐graft‐polystyrene and application to preparation of porous membranes

Poly(vinyl acetate)–TEMPO (PVAc–TEMPO) macroinitiators were synthesized by bulk polymerization of vinyl acetate in the presence of benzoyl peroxide (BPO) followed by termination with 2,2,6,6‐tetramethyl‐1‐piperidinyloxy (TEMPO). Radicals were mainly transferred to the acetoxy methyl groups in PVAc during the polymerization. The PVAc–TEMPO macroinitiators had several TEMPO‐dormant sites and styrene bulk polymerization with the macroinitiators produced poly(vinyl acetate)‐graft‐polystyrene (PVAc‐g‐PS). All the TEMPO‐dormant sites of PVAc–TEMPO macroinitiators participated in the styrene polymerization with almost equal reactivity. Methanolysis of PVAc‐g‐PS broke the PS branches apart from the PVAc backbone chains. Hydrophobic or hydrophilic porous membranes with controlled pore size could be prepared by removing the PVAc domains or the PS domains from the graft copolymer. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1658–1667, 2001     

Metal ion interaction of water‐soluble copolymers containing carboxylic acid groups in aqueous phase by membrane filtration technique

This article reports the synthesis of poly(N‐maleoylglycine‐co‐itaconic acid) by radical copolymerization under different feed mole ratios and its properties to remove various metal ions, such as Cu(II), Cr(III), Co(II), Zn(II), Ni(II), Pb(II), Cd(II), and Fe(III), in aqueous phase with the liquid‐phase polymer‐based retention(LPR) technique. The interactions of inorganic ions with the hydrophilic water‐soluble polymer were determined as a function of pH and filtration factor. Metal ion retention was found to strongly depend on the pH. Metal ion retention increased as pH and MG content units in the macromolecular backbone increased. The copolymers were characterized by elemental analysis, FTIR, ¹H‐NMR, and ¹³C‐NMR spectroscopy. Additionally, intrinsic viscosity, molecular weight, and polydispersity have been determined for the copolymers. Copolymer and polymer–metal complex thermal behavior was studied using differential scanning calorimetry (DSC) and thermogravimetry (TG) techniques under nitrogen atmosphere. The thermal decomposition temperatures (TDT) were influenced by the copolymer composition. The copolymers present lower TDT than the polymer–metal complex with the same copolymer composition. All copolymers present a single T_g, indicating the formation of random copolymers. A slight deviation of the T_g for the copolymers and its complexes can be observed. The copolymer T_g is higher than the T_g value for the polymer–metal complexes. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Poly(9‐vinylcarbazole)/silver composite nanotubes and networks formed at the air–water interface

Silver‐nanoparticle‐doped poly(9‐vinylcarbazole) (PVK) nanocomposites were prepared via the reduction of Ag⁺ ions and the self‐assembly of PVK on AgNO₃ aqueous solution surfaces. The formed composite nanostructures depended strongly on the experimental temperature. Thick round disks of PVK surrounded by discrete Ag nanoparticles and/or with irregular holes formed at room temperature; nanotubes and micronetworks doped with Ag nanoparticles formed at about 30–40°C, and networks formed at higher temperature. Further investigation revealed that the nanotubes were transformed from thin round disks. The length of the PVK/Ag composite nanotubes were longer than 10 μm, and the average size of the embedded Ag nanoparticles was found to be about 3.5 nm. The composite networks were composed of round pores with diameters of several hundred nanometers and fine silver nanoparticles embedded in the thin polymer films that covered the pores. The formation of the nanotubes was a very interesting self‐assembly phenomenon of the polymer at the air–water interface that has not been reported before. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Inverse gas chromatography study of polyvinylacetate–solvent and polyethylene–solvent systems

In this article, the thermodynamic behavior of polyvinylacetate (PVAc)–solvent, and polyethylene (PE)–solvent mixtures have been studied by determining the thermodynamic sorption parameters (enthalpy, entropy, and free energy), the mass‐based solvent activity coefficients (Ω) and the Flory Huggins parameters (χ), by means of inverse gas chromatography (IGC) measurements. According to the Flory Huggins parameters of the PE–solvent mixtures, determined between 40 and 60°C the compatibility (the ability to interact with each other) of this polymer with the different types of solvents follows this order: dispersion solvents > polar solvents > association solvents. In the case of PVAc mixtures, the thermodynamic parameters were determined between 60 and 80°C, only for polar‐type and association‐type solvents due to, in the studied temperature range, the retention diagrams of dispersion solvents show that there are not bulk interactions. The Hildebrand solubility parameters of both polymers were also determined, according to Guillet procedure. The higher values of PVAc material (14.1 MPa^0.5 for PE and 19.8 MPa^0.5 for PVAc, at 60°C) are related to the strong interactions of vinyl acetate monomer. POLYM. ENG. SCI., 56:36–43, 2016. © 2015 Society of Plastics Engineers     

Preparation and characterization of biodegradable polymer blends from poly(3‐hydroxybutyrate)/poly(vinyl acetate)‐modified corn starch

Biodegradable polymer blends prepared by blending poly(3‐hydroxybutyrate) (PHB) and corn starch do not form intact films due to their incompatibility and brittle behavior. For improving their compatibility and flexibility, poly(vinyl acetate) (PVAc) was grafted from the corn starch to prepare the PVAc‐modified corn starch (CSV). The resulting CSV consisted of 47.2 wt% starch‐g‐PVAc copolymer and 52.8 wt% PVAc homopolymer and its structure was verified by FT‐IR analysis. In comparison with 35°C of the neat PVAc, the glass transition temperature (T_g) of the grafted PVAc chains on starch‐g‐PVAc was higher at 44°C because of the hindered molecular mobility imposed from starch on the grafted PVAc. After blending PHB with the CSV, structure and thermal properties of the blends were investigated. Only a single T_g was found for all the PHB/CSV blends and increased with increasing the CSV content. The T_g‐composition dependence of the PHB/CSV blends was well‐fitted with the Gordon‐Taylor equation, indicating that the CSV was compatible with the PHB. In addition, the presence of the CSV could raise the thermal stability of the PHB component. It was also found that the presence of the PHB and PVAc components would not hinder the enzymatic degradation of the corn starch by α‐amylase. POLYM. ENG. SCI., 55:1321–1329, 2015. © 2015 Society of Plastics Engineers     

Molecular‐Like Ag Clusters and Eu3+ Co‐Sensitized Efficient Broadband Spectral Modification with Enhanced Yb3+ Emission

AgNO₃/EuF₃/YbF₃ tri‐doped oxyfluoride glass was prepared by a melt‐quenching method, in which a high‐efficient broadband spectral modification can be realized due to the simultaneous energy‐transfer processes of Eu³⁺→Yb³⁺, molecular‐like Ag (ML‐Ag) clusters→Yb³⁺, and ML‐Ag clusters→Eu³⁺→Yb³⁺. The spectral measurements indicated that besides the F‐center brought by the fluorides, the formation of the ML‐Ag clusters and the evolution of silver species within the glass matrix were also closely related to the introduction of Eu³⁺ and Yb³⁺ ions and which in return greatly affected the luminescence properties of these rare‐earth ions. As the UV‐visible irradiation in the wavelength region of 250–600 nm can be efficiently converted into near‐infrared emission around 1000 nm in the AgNO₃/EuF₃/YbF₃ tri‐doped glass, which thus has promising application in enhancing the photovoltaic conversion efficiency of the silicon solar cell.     

Preparation of Ag nanoparticles in the presence of low generational poly(ester‐amine) dendrimers

Stable Ag nanoparticles of 10–20 nm were prepared by reduction of AgNO₃ with NaBH₄ in water solution in the presence of low generational hydroxyl‐ terminated poly(ester‐amine) dendrimer G1.0 (OH)₁₆ and amino‐terminated poly(ester‐amine) dendrimer G1.5 (NH₂)₈ by optimizing preparation conditions. UV–vis absorption spectra and transmission electron microscopy were adopted to characterize absorption properties of Ag⁺/dendrimer complex, Ag/dendrimer nanocomposite aqueous solutions, and the morphology of the formed Ag nanoparticles, respectively. The results showed that the size of the Ag particles increased with Ag⁺/dendrimer molar ratio, and the size of Ag nanoparticles in Ag/G1.0 (OH)₁₆ system was larger than that of Ag nanoparticles in Ag/G1.5 (NH₂)₈ system, while the polydispersities of two systems were similar. Moreover, the Ag/G1.5 (NH₂)₈ nanocomposite system was more stable than the Ag/G1.0 (OH)₁₆ one. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 422–426, 2007     

A novel method for preparing silver/poly(siloxane‐b‐methyl methacrylate) nanocomposites with multiple properties in the DMF‐toluene mixture solvent

A novel method for preparing silver/poly(siloxane‐b‐methyl methacrylate) (Ag/(PDMS‐b‐PMMA)) hybrid nanocomposites was proposed by using the siloxane‐containing block copolymers as stabilizer. The reduction of silver nitrate (AgNO₃) was performed in the mixture solvent of dimethyl formamide (DMF) and toluene, which was used to dissolve double‐hydrophobic copolymer, as well as served as the powerful reductant. The presence of the PMMA block in the copolymer indeed exerted as capping ligands for nanoparticles. The resultant nanocomposites exhibited super hydrophobicity with water contact angle of 123.3^° and the thermogravimetry analysis (TGA) revealed that the resultant nanocomposites with more PDMS were more heat‐resisting. Besides, the antimicrobial efficiency of the most desirable nanocomposite (Ag/PDMS₆₅‐b‐PMMA₃₀ loaded with 7.3% silver nanoparticle) could reach up to 99.4% when contacting with escherichia coli within 120 min. As a whole, the resultant nanocomposites by the integration of excellent properties of silver nanoparticles as well as siloxane‐block copolymers can be a promising for the development of materials with hydrophobic, heat‐resisting and outstanding antibacterial properties from the chemical product engineering viewpoint. © 2013 American Institute of Chemical Engineers AIChE J, 59: 4780–4793, 2013     

Dynamic–mechanical properties of modified poly(ethylene‐co‐vinyl acetate)

To study the relationship among relaxation peaks observed in dynamic mechanical experiments and the structure of poly(ethylene‐co‐vinyl acetate) (EVA), EVA copolymers with different substitution in the carbonyl group were synthesized. EVA was hydrolyzed to obtain poly (ethylene‐co‐vinyl alcohol) and was subsequently reacted with formic, hexanoic, and octanoic acids. The copolymers synthesized were characterized by infrared spectroscopy. Analysis of the DMA spectra of the copolymers showed that their relaxation behavior depends on the vinyl acetate concentration. The α‐ and β‐transitions were observed in EVA copolymers with 8 and 18 wt % of functional groups, and the relationship among relaxation process with the structure of polymer was investigated. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1371–1376, 2005     

Infusion of Ag‐Ion from Aqueous Solution into Solid Calcium Phosphate of Hydroxyapatite (HA) Crystal Structure

In contrast to extensive literature concerning Ag incorporation in hydroxyapatite, HA, while the phosphate approximated to stoichiometry of Ca₁₀(PO₄)₆(OH)₂, with added Ag has been precipitating from an aqueous solution, the paper presents Ag incorporation through Ag ion infusion from AgNO₃ solution into solid HA pressed in pellet and ignited at 800°C. After Ag ions infused into the HA‐solid (crossed the interfacial solution‐solid boundary), they diffused across the crystal structure to a depth of time‐dependent several mm. The path of Ag diffusion in the solid HA was recorded using SEM‐EDS point analyses of Ag, Ca, P, EDS‐linear analyses of those elements, and elemental mapping. Time‐dependent concentrations of Ag⁺, Ca²⁺, and PO₄^3? in AgNO₃ solutions were also analyzed. The appearance of Ag in the crystalline HA with simultaneous local depletion in Ca and phosphate recorded as P, observed by EDS with simultaneous appearance of Ca²⁺ and PO₄^3? ions and a decrease in Ag⁺ concentration in AgNO₃ solution led the authors to a conclusion that Ag⁺ for Ca²⁺ substitution supported by PO₄^3? charge balancing in the crystalline HA was in process. The HA particles in the section of the pellet without Ag had a uniform shape and size approximated to 300–400 nm. SEM image of the HA solid section, where Ag ions appeared was characterized by irregular aggregates of smaller crystals with sporadically present large, shaped in prism blocks identified by the XRD as Ag₃PO₄.     

High‐resolution solid‐state NMR investigation of the filler–rubber interaction: 2. High‐speed [1H] magic‐angle spinning NMR spectroscopy in carbon‐black‐filled polybutadiene

This work investigates the behaviour of elastomeric chains (polybutadienes of identical molecular weight but different microstructures) in the close vicinity of carbon black surfaces in order to attain a better understanding of the structure and properties of interphases. Elastomer–filler interactions are assessed through the study of the thermal properties and NMR relaxation characteristics of the corresponding materials. Three series of samples were compared: pure polymers, raw polymer–filler blends (filler loading ratio: 50 phr) and solvent‐extracted blends (so as to get rid of any polymer which is not under the influence of the solid surface). While differential scanning calorimetry points to the existence of an elastomer fraction which is not detected as undergoing the glass transition, ie is strongly immobilized, [¹H] high‐resolution high‐speed magic‐angle spinning solid‐state NMR provides information on the effect exerted by polymer–filler interactions on the mobility of the various constitutive species of the macromolecular backbone. A systematic study of the evolution of the spectral lines yielded by the samples indicates that 1,2‐polybutadiene moieties have a particular affinity towards the carbon black surface which suggests the occurrence of specific interactions at the elastomer–filler interface. © 2001 Society of Chemical Industry