质子化哌嗪化学吸收CO2过程研究与分析

为研究有机胺吸收/解吸CO₂变化过程,以哌嗪(PZ)为吸收剂,利用浓硫酸调节PZ的质子化程度,通过核磁共振技术研究不同pH下的PZ溶液吸收CO₂情况,进一步揭示PZ和质子化PZ化学吸收/解吸CO₂的过程机理。结果表明,吸收过程中PZ与CO₂反应生成哌嗪单氨基甲酸盐和双氨基甲酸盐;当溶液pH为7.95时,溶液中哌嗪双氨基甲酸盐和部分单氨基甲酸盐发生水解,生成碳酸氢根;当溶液pH低于7.95时,溶液中CO₂以哌嗪单氨基甲酸盐和碳酸氢根形式共存。与PZ吸收剂相比,质子化PZ吸收CO₂过程中的双氨基甲酸盐相对含量降低,解吸性能提高,有利于PZ吸收剂的再生。     

复合溶液膜吸收CO2的性能及其对膜孔润湿的影响

利用自行搭建的CO₂膜吸收实验台，采用聚丙烯（PP）膜组件，以质量分数10%的N-甲基二乙醇胺（MDEA）作为主体胺溶液，添加不同配比的哌嗪（PZ）、乙醇胺（MEA）、甘氨酸钾（PG），考察CO₂脱除效率和传质速率的变化，比较不同复配比的复合溶液表面张力以及对PP膜的浸润性，并以10%MDEA+10%PG混合溶液作为吸收液进行长时间实验。结果表明：添加少量的添加剂对MDEA溶液膜吸收CO₂均有显著的促进作用，当配比小于0.2时，促进作用大小为PZ>MEA>PG；当配比大于0.2时，促进作用大小为PZ>PG>MEA；PZ和MEA均随着添加配比的增加，溶液表面张力减小，而PG相反；表面张力小的溶液对膜浸润性较强，容易造成膜润湿；添加剂质量分数均为10%时，对膜溶胀性和疏水性以及膜孔结构影响大小为PZ>MEA>PG；在20天内，PG/MDEA混合溶液作用下的CO₂脱除效率从89.56%下降为83.09%，对PP的疏水性影响较小，膜组件可以稳定运行。吸收液表面张力对膜吸收法脱除CO₂性能的影响显著。所得结果可为膜吸收CO₂吸收剂复配提供依据，并可为揭示膜吸收CO₂过程中膜润湿导致膜失效的机理以及抑制膜润湿提供实验数据。     

负载型K2CO3/Al2O3吸收剂吸收CO2反应机理

利用热重分析仪、扫描电镜和氮吸附仪对不同粒径的K₂CO₃颗粒和负载型K₂CO₃/Al₂O₃二氧化碳吸收剂的碳酸化特性进行研究。负载后的吸收剂比表面积和孔隙结构得到较大改善,使得碳酸化反应速率和转化率均提高,吸收剂碳酸化特性得到改善。纯K₂CO₃颗粒吸收剂的反应速率和转化率随着粒径的增加而减小,负载型吸收剂的反应速率和转化率随着粒径的增加略增大。研究了不同粒径和反应时间对K₂CO₃/Al₂O₃颗粒微观结构的影响,结果表明K₂CO₃/Al₂O₃颗粒具有较稳定的微观结构。采用负载型粒子模型对K₂CO₃/Al₂O₃吸收剂吸收CO₂碳酸化过程进行研究,所建立的粒子模型计算结果与试验值吻合较好。利用建立的模型对不同CO₂浓度下K₂CO₃/Al₂O₃吸收剂碳酸化反应特性进行模拟计算,模拟结果具备一定的合理性和准确性,为开展进一步研究提供了基础。     

MDEA-PZ复合胺溶液吸收烟气中CO2实验研究

采用搅拌实验装置,研究不同摩尔配比的MDEA-PZ复合胺溶液对烟道气中CO2的吸收和解吸性能,揭示了吸收速率、吸收量与吸收时间、pH值、电位之间的内在联系;对CO2初始逸出温度、试液再生温度、再生率、再生pH值下降率进行了分析。结果表明,MDEA—PZ二元复合体系吸收效果优于单组分MDEA、PZ的吸收效果。MDEA—PZ复合胺溶液摩尔配比为0．5：0．5时,吸收效果最佳,吸收量约为0．8mol·L^-1;CO2初始逸出温度最低,为54℃;再生温度最低,为102℃;再生率最高,为88．61％;再生pH值下降率最低,为11．39％。MDEA-PZ复合体系的两种组分之间存在正交互作用。     

燃煤电厂烟气MDEA/PZ混合胺法碳捕集工艺模拟分析

采用混合胺吸收剂替代传统一乙醇胺（MEA）吸收剂是降低有机胺法碳捕集工艺能耗的重要方法。利用Aspen plus软件模拟了以甲基二乙醇胺(MDEA)/哌嗪(PZ)混合胺为吸收剂的燃煤电厂每年百万吨CO₂捕集工艺系统，考察了贫液负荷、MDEA/PZ混合胺浓度、MDEA/PZ比例和解吸压力等因素对解吸塔再沸器热负荷和冷凝器冷负荷的影响。通过对这些影响因素下吸收塔内液相温度分布和CO₂负荷分布变化揭示了MDEA/PZ对CO₂的吸收特性。此外，进一步分析了不同影响因素下解吸塔内气液相CO₂浓度驱动力和气液相级间温度驱动力分布特性，发现了强浓度驱动力和低温度驱动力分布更有利于降低再生能耗。研究表明，由30%MDEA和20%PZ组成的混合胺液在贫液负荷为0.08和解吸压力为2.02×10⁵Pa时，再沸器热负荷和塔顶冷凝负荷分别为2.76GJ/tCO₂和0.60GJ/tCO₂，相比传统MEA吸收剂降低了20.92%和40.0%。     

自活化PAN基多孔碳纤维的制备及其CO2吸附性能研究

以碳酸钾(K₂CO₃)为添加剂，通过湿法纺丝制备出具有自活化特性的聚丙烯腈(PAN)原丝，然后通过同步碳化与活化制得一种用于二氧化碳(CO₂)吸附的自活化PAN基多孔碳纤维，研究了K₂CO₃对自活化碳纤维的化学组成与孔结构的影响，探讨了在模拟烟气环境中自活化碳纤维的CO₂吸附性能。结果表明：随着K₂CO₃含量的增加，自活化碳纤维内部骨架逐渐表现出疏松多孔结构；自活化碳纤维具有高氮(N)含量，掺杂K₂CO₃质量分数为1%时纤维的N质量分数最高，达16.0%;自活化碳纤维的多孔结构及高N含量有利于对CO₂的吸附，掺杂K₂CO₃质量分数为3%的自活化碳纤维在40℃模拟烟气环境中的CO₂吸附量最高，达30.5 mg/g,表现出良好的CO₂吸附性能。     

离子液体-水复配吸收剂捕获CO2性能

基于绿色合成方法制备出亲水性离子液体(ILs)[NH₂-C₃mim][Br],从有效降低CO₂吸收-解吸操作成本出发,采用ILs-H₂O复配吸收剂,开展了常温加压CO₂吸收及吸收剂常温减压解吸再生实验。结果表明,比CO₂吸收量(基于复配吸收剂或离子液体组分)随复配吸收剂中ILs组分浓度而变;吸收初期,CO₂吸收速率随吸收剂配比变化显著;以CO₂高吸收率和吸收剂低成本为目标,优选出新型水基复配吸收剂(离子液体与水质量比为1.38:1)。分别以水基离子溶液、改良热钾碱液和活化复配醇胺液为吸收剂,在自行搭建的超重力场强化吸收-连续逆流接触(加热或减压)解吸再生台架实验装置上进行了CO₂捕获与吸收剂再生连续化实验。结果表明,在超重力场作用下,改良热钾碱液和活化复配醇胺液对CO₂有较好的捕获,吸收率分别在98%、96%和90%以上,3种吸收剂经加热或减压解吸再生后均可循环回用,水基离子溶液吸收剂在常温减压下解吸更具有实际可操作性。     

MDEA-PZ复合胺溶液吸收烟气中CO2实验研究

采用搅拌实验装置,研究不同摩尔配比的MDEA-PZ复合胺溶液对烟道气中CO2的吸收和解吸性能,揭示了吸收速率、吸收量与吸收时间、pH值、电位之间的内在联系;对CO2初始选出温度、试液再生温度、再生率、再生pH值下降率进行了分析.结果表明,MDEA-PZ二元复合体系吸收效果优于单组分MDEA、PZ的吸收效果.MDEA-P...     

沼气提纯过程中醇胺溶液吸收CO2传质性能

醇胺溶液吸收CO₂是沼气提纯领域重要的研究课题。在实验填料吸收塔中,以乙醇胺(MEA)、二乙醇胺(DEA)为吸收剂,研究了吸收剂浓度、进气流量、CO₂浓度、进液温度对吸收过程转化率η、吸收速率N以及气相总体积传质系数K_Ga_e的影响。结果表明,吸收剂浓度增加可有效提高η、N及K_Ga_e;进气流率增加,η逐渐降低,N先增加后降低,K_Ga_e先增加后降低最终趋于稳定;随着CO₂浓度增加,η和K_Ga_e不断降低,N逐渐增加;随着进液温度升高,η和K_Ga_e均先升高后降低;MEA、DEA的最佳进液温度在40～60℃之间,并随CO₂负载量增大而逐渐降低。研究结果对于醇胺溶液吸收法沼气提纯技术的研究开发和实际应用有参考作用。     

基于pH测量的CO2吸收到钠基溶液动态实验及模型

采用基于pH测量的CO₂吸收速率研究方法。将pH与溶液中的成分相关联,采用分段拟合获得CO₂吸收速率,获得溶液成分对吸收速率的影响规律。对于低浓度的NaOH来说,吸收速率一直保持不变直到CO₂物理吸收到NaHCO₃溶液中。对于高浓度的NaOH,NaOH完全转化成Na₂CO₃时,吸收速率降低。但在两个吸收阶段中,吸收速率不变,CO₂物理吸收到NaHCO₃中时,吸收速率随CO₂饱和度的增加而降低。对CO₂吸收到NaOH中,CO₂和钠离子浓度都促进吸收,钠离子浓度影响更大;对于CO₂吸收到Na₂CO₃中,当Na₂CO₃浓度大于0.05mol/L,吸收速率不随浓度增加;对于CO₂吸收到NaHCO₃中,低浓度的钠可以促进CO₂吸收,而高浓度的钠抑制CO₂吸收,这主要由于析盐的作用。为避免CO₂大量吸收,优先选择0.5mol/L以上浓度的NaHCO₃。     

CO2 absorption and regeneration of alkali metal-based solid sorbents

Potassium-based sorbents were prepared by impregnation with potassium carbonate on supports such as activated carbon (AC), TiO₂, Al₂O₃, MgO, SiO₂ and various zeolites. The CO₂ capture capacity and regeneration property were measured in the presence of H₂O in a fixed-bed reactor, during multiple cycles at various temperature conditions (CO₂ capture at 60 °C and regeneration at 130–400 °C). Sorbents such as K₂CO₃/AC, K₂CO₃/TiO₂, K₂CO₃/MgO, and K₂CO₃/Al₂O₃, which showed excellent CO₂ capture capacity, could be completely regenerated above 130, 130, 350, and 400 °C, respectively. The decrease in the CO₂ capture capacity of K₂CO₃/Al₂O₃ and K₂CO₃/MgO, after regeneration at temperatures of less than 200 °C, could be explained through the formation of KAl(CO₃)₂(OH)₂, K₂Mg(CO₃)₂, and K₂Mg(CO₃)₂·4(H₂O), which did not completely converted to the original K₂CO₃ phase. In the case of K₂CO₃/AC and K₂CO₃/TiO₂, a KHCO₃ crystal structure was formed during CO₂ absorption, unlike K₂CO₃/Al₂O₃ and K₂CO₃/MgO. This phase could be easily converted into the original phase during regeneration, even at a low temperature (130 °C). Therefore, the formation of the KHCO₃ crystal structure after CO₂ absorption is an important factor for regeneration, even at the low temperature. The nature of support plays an important role for CO₂ absorption and regeneration capacities. In particular, the K₂CO₃/TiO₂ sorbent showed excellent characteristics in CO₂ absorption and regeneration in that it satisfies the requirements of a large amount of CO₂ absorption (mg CO₂/g sorbent) and fast and complete regeneration at a low temperature condition (1 atm, 150 °C).     

Effect of K2CO3 doping on CO2 sorption performance of silicate lithium-based sorbent prepared from citric acid treated sediment

In this paper, a low-cost and environmental-friendly leaching agent citric acid (C₆H₈O₇) was used to treat the sediment of Dianchi Lake (SDL) to synthesize lithium silicate (Li₄SiO₄) based CO₂ sorbent. The results were compared with that treated with strong acid. Moreover, the effects of preparation conditions, sorption conditions and desorption conditions on the CO₂ sorption performance of prepared Li₄SiO₄ were systematically studied. Under optimal conditions, the Li₄SiO₄ sorbent was successfully synthesized and its CO₂ sorption capacity reached 31.37% (mass), which is much higher than that synthesized from SDL treated with strong acid. It is speculated that the presence of some elements after C₆H₈O₇ treatment may promote the sorption of synthetic Li₄SiO₄ to CO₂. In addition, after doping with K₂CO₃, the CO₂ uptake increases from the original 12.02% and 22.12% to 23.96% and 32.41% (mass) under the 20% and 50% CO₂ partial pressure, respectively. More importantly, after doping K₂CO₃, the synthesized Li₄SiO₄ has a high cyclic stability under the low CO₂ partial pressure.     

氨水吸收CO2的吸收热预测模型

基于e-NRTL模型,利用Aspen Plus软件建立了氨水吸收CO₂的吸收热预测模型,验证了NH₃-CO₂-H₂O体系的汽液平衡、液相组成形态并与前人的实验数据做了对比,进而结合负载CO₂的氨水溶液中各离子及分子的变化特征,对CO₂吸收过程的反应热随着CO₂负载量的变化规律进行了预测并与已发表的数据进行了比较。结果表明,该吸收热模型能够准确地实现氨水吸收CO₂过程中汽液平衡、液相反应以及吸收热的计算。氨水吸收CO₂的反应热主要受H₂O的电离、NH₃的电离、NH₂COO^-的生成与水解、CO₂的溶解等反应过程的影响,H₂O的电离过程受NH₃的电离过程的抑制,对于总吸收热的贡献最大, NH₂COO^-的反应则随着CO₂负载量的增加先放热再吸热。随着温度的升高,总吸收热有所降低,当温度为80℃时,在较低的CO₂负载区间[0.2～0.5 mol CO₂·(mol NH₃)^-1],总吸收热约为70.5 kJ·(mol CO₂)^-1。     

Simultaneous desulfurization and denitrification of flue gas by pre-ozonation combined with ammonia absorption

A process of simultaneous desulfurization and denitrification of flue gas was conducted in this study. The flue gas containing 200 mg·m^-3 NO, 1000-4000 mg·m^-3 SO₂, 3%-9% O₂, and 10%-20% CO₂ was first oxidized by O₃ and then absorbed by ammonia in a bubbling reactor. Increasing the ammonia concentration or the SO₂ content in flue gas can promote the absorption of NO_X and extend the effective absorption time. On the contrary, both increasing the absorbent temperature or the O₂ content shorten the effective absorption time of NO_X. The change of solution pH had substantial influence on NO_X absorption. In the presence of CO₂, the NO_X removal efficiency reached 89.2% when the absorbent temperature was raised to 60 °C, and the effective absorption time can be maintained for 8 h, which attribute to the buffering effect in the absorbent. Besides, both the addition of Na₂S₂O₃ and urea can promote the NO_X removal efficiency when the absorbent temperature is 25 °C, and the addition of Na₂S₂O₃ had achieved better results. The advantage of adding Na₂S₂O₃ became less evident at higher absorbent temperature and coexistence of CO₂. In all experiments, SO₂ removal efficiency was always above 99%, and it was basically not affected by the above factors.     

制备活性炭负载K2CO3用于催化餐饮废油合成生物柴油

以K₂CO₃为催化剂,工业碱木质素(KL)为活性炭(AC)前体,在管式电阻炉中经一步共混活化(K₂CO₃/KL质量比为0.6、活化温度800℃、N₂流量100cm³/min、活化时间2h)制备K₂CO₃/AC固体碱催化剂,用于餐饮废油与甲醇的酯交换反应合成生物柴油。对制备的固体碱催化剂进行了X-射线衍射(XRD)、BET表面积及扫描电镜(SEM)表征。考察了反应温度、催化剂用量、反应时间、醇油摩尔比等因素对餐饮废油转化为生物柴油产率的影响。结果表明当反应时间2h、反应温度60℃、醇油摩尔比15:1、催化剂为原料油质量的3.0%时,生物柴油最大产率为87.5%。考查了催化剂的循环利用效果,结果表明催化剂能循环利用3次,第3次利用时生物柴油的产率仍达到80.7%。     

K2CO3对兰炭催化气化特性的影响

在固定床中考察了不同K₂CO₃植入浓度和不同温度条件下兰炭催化气化特性。结果表明，5%的催化剂植入浓度主要起到填充孔隙的作用，当植入浓度增加到10%以后，催化剂发生堆积会使颗粒表面及内部形成较多孔隙。提高气化温度可提高兰炭转化率，超过750℃之后碳转化率增幅减缓，催化剂饱和装载浓度为10%。在颗粒表面和开放孔隙中的高浓度C(O)才具有较高的脱附速率，并提高CO生成速率。在非催化条件下，随着气化的进行CO/CO₂下降，而H₂/(2CO₂+CO)先增后减。在催化条件下，H₂/(2CO₂+CO)稳定在1.5～1.7。催化剂兰炭样品中出现了K₂Ca(CO₃)₂双金属碳酸盐、K₂O、KO₂等活性组分，并随催化剂植入浓度的增加而增加。催化剂植入浓度的增加会导致失活现象加重，但兰炭在750℃条件下气化1 h 催化剂没有完全失活。     

Operating limits and features of direct air capture on K2CO3/ZrO2 composite sorbent

Potassium carbonate-based sorbents are prospective materials for direct air capture (DAC). In the present study, we examined and revealed the influence of the temperature swing adsorption (TSA) cycle conditions on the CO₂ sorption properties of a novel aerogel-based K₂CO₃/ZrO₂ sorbent in a DAC process. It was shown that the humidity and temperature drastically affect the sorption dynamic and sorption capacity of the sorbent. When a temperature at the sorption stage was 29 ℃ and a water vapor pressure in the feed air was 5.2 mbar (1 bar = 10⁵ Pa), the composite material demonstrated a stable CO₂ sorption capacity of 3.4% (mass). An increase in sorption temperature leads to a continuous decrease in the CO₂ absorption capacity reaching a value of 0.7% (mass) at T = 80 ℃. The material showed the retention of a stable CO₂ sorption capacity for many cycles at each temperature in the range. Increasing P_H2O in the inlet air from 5.2 to 6.8 mbar leads to instability of CO₂ sorption capacity which decreases in the course of 3 consecutive TSA cycles from 1.7% to 0.8% (mass) at T = 29 ℃. A further increase in air humidity only facilitates the deterioration of the CO₂ sorption capacity of the material. A possible explanation for this phenomenon could be the filling of the porous system of the sorbent with solid reaction products and an aqueous solution of potassium salts, which leads to a significant slowdown in the CO₂ diffusion in the composite sorbent grain. To investigate the regeneration step of the TSA cycle in situ, the macro ATR-FTIR (attenuated total reflection Fourier-transform infrared) spectroscopic imaging was applied for the first time. It was shown that the migration of carbonate-containing species over the surface of sorbent occurs during the thermal regeneration stage of the TSA cycle. The movement of the active component in the porous matrix of the sorbent can affect the sorption characteristics of the composite material. The revealed features make it possible to formulate the requirements and limitations that need to be taken into account for the practical implementation of the DAC process using the K₂CO₃/ZrO₂ composite sorbent.     

固体碱K_2CO_3/Al-Ni及K_2CO_3/Al-Ni-O催化制备生物柴油

分别采用合成的铝镍类水滑石和其焙烧后复合氧化物为载体,负载K_2CO_3制得负载型固体碱催化剂,并用于催化食用菜籽油制生物柴油的反应。考察甲醇与菜籽油物质的量比、反应时间和反应温度对催化性能的影响,结果表明,在甲醇与菜籽油物质的量比10∶1、反应温度60℃、反应时间6 h和催化剂用量为油质量的5%条件下,生物柴油产率最高,为82.4%,且催化剂可重复使用,具有稳定的催化作用。