Dynamic mechanical properties and morphology of high‐density polyethylene/CaCO3 blends with and without an impact modifier

Dynamic mechanical analysis and differential scanning calorimetry were used to investigate the relaxations and crystallization of high‐density polyethylene (HDPE) reinforced with calcium carbonate (CaCO₃) particles and an elastomer. Five series of blends were designed and manufactured, including one series of binary blends composed of HDPE and amino acid treated CaCO₃ and four series of ternary blends composed of HDPE, treated or untreated CaCO₃, and a polyolefin elastomer [poly(ethylene‐co‐octene) (POE)] grafted with maleic anhydride. The analysis of the tan δ diagrams indicated that the ternary blends exhibited phase separation. The modulus increased significantly with the CaCO₃ content, and the glass‐transition temperature of POE was the leading parameter that controlled the mechanical properties of the ternary blends. The dynamic mechanical properties and crystallization of the blends were controlled by the synergistic effect of CaCO₃ and maleic anhydride grafted POE, which was favored by the core–shell structure of the inclusions. The treatment of the CaCO₃ filler had little influence on the mechanical properties and morphology. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3907–3914, 2007     

Investigation into the morphology and mechanical properties of melt‐drawn filaments from uncompatibilized blends of polystyrene and high‐density polyethylene

Uncompatibilized immiscible blends of polystyrene (PS) and high‐density polyethylene (HDPE) were melt‐processed in a single‐screw extruder fitted with a fine screen mesh and capillary die and were further drawn into filaments to produce near‐nanoscale immiscible domains. The resultant morphologies and mechanical properties were studied for these structures in which load transfer is achieved solely by mechanical linkages between blend domains. The morphology of the blends revealed co‐continuity approximately in the range of 45–47 volume percent PS. The development of a three‐dimensional co‐continuous network in 45 vol% PS, as revealed by morphology observations, was also related to a decrease in extruder output rate in this region, an indicator of the melt interaction of the two phases as co‐continuity is achieved. Image analysis revealed submicron fibrillar structures near the phase inversion composition where domain sizes ranged from 6–220 nm with an average domain size of 90 nm. Tensile modulus increased with increasing PS content (E = 2.7 GPa at 47% PS) over the entire blend range with values greater than the rule of mixtures up to 50% PS. Strain to failure did not seem to be influenced by co‐continuous morphologies and the fine dispersion of PS domains appears to constrain the fundamentally high strain of HDPE. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1616–1625, 2007     

Preparation and characterization of blends of high density polyethylene and poly(ethylene‐co‐1‐octene) elastomer

Mechanical, thermal, and morphological properties of blends of high density polyethylene and poly(ethylene‐co‐1‐octene) (PEO) were evaluated. The blends were prepared in a single screw extruder at 230°C and 50 rpm with volume fraction of elastomer varying in the range from 0.05 to 0.8. Factors such as chemical similarity and melt viscosity favor the interdiffusion process of phases, resulting in better interfacial adhesion. A synergistic effect on the strength at break and elongation at break for a particular range of blend composition was observed. Blends with a volume fraction of PEO higher than 5% presented a super tough behavior at room temperature. Thermal analysis showed that there is a certain degree of interaction between high density polyethylene and PEO. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1991–1995, 2001     

Preparation,morphology, and mechanical properties of elastomers based on polydimethylsiloxane/ polystyrene blends

Polydimethylsiloxane/polystyrene (PDMS/PS) blends were prepared by radical copolymerization of styrene (St) and divinylbenzene (DVB) in the presence of α,ω‐dihydroxy‐polydimethylsiloxane (PDMS), using benzoyl peroxide as initiator. The PDMS/PS blends obtained by this method are a series of stable, white gums, when the feed ratio of PDMS to St is 60/40 and DVB to St is not more than 2.0 wt %. Elastomers based on PDMS/PS blends were formed by crosslinking PDMS with methyl‐triethoxysilicane (MTES). The MTES dosage was much larger than the amount necessary for end‐linking hydroxy‐terminated chains of PDMS, with the excess being hydrolyzed to crosslinked networks, which were similar to SiO₂ and acted as filler. Mechanical property measurements show that the elastomers thus formed exhibit superior mechanical properties with respect to pure PDMS elastomer and the elastomers based on PDMS/PS system we prepared before. Moreover, investigations were carried out on the elastomers by extraction measurement and scanning electron microscopy (SEM). The extraction data show that the sol‐fraction decreases with increasing the feed ratio of DVB to St. SEM observation demonstrates that the elastomer has a microphase‐separated structure consisting of dispersed PS domains within a continuous PDMS matrix, and the extracted material exhibits a porous structure. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Orientation effects on the deformation and fracture properties of high‐density polyethylene/ethylene vinyl acetate (HDPE/EVA) blends

In this paper, the tensile deformation and fracture toughness of high‐density polyethylene (HDPE)/ethylene vinyl acetate (EVA) blends, obtained by dynamic packing injection moulding, have been comprehensively investigated in different directions of rectangle samples, including longitudinal, latitudinal and oblique directions relative to the flow direction. Two kinds of EVA were used with VA content 16 wt% (16EVA) and 33 wt% (33EVA) to control the interfacial interactions. The results indicate that molecular orientation and interfacial interaction play very important roles to determine the tensile behaviour and fracture toughness. Biaxial‐reinforcement of tensile strength was seen for HDPE/16EVA blends but only uniaxial‐reinforcement was observed for HDPE/33EVA blends. The difference is caused by the different interfacial interactions as highlighted by the peel test, scanning electron microscopy (SEM) observation as well as theoretical evaluation. Very high impact strength, decreasing with increasing EVA content, was observed when the fracture propagation is perpendicular to the shear flow direction, while a low impact strength, increasing slightly increasing with EVA content, was seen when the fracture propagation is parallel to the shear flow. The fracture of oblique samples is always along the flow direction instead of along the impact direction or tensile direction. The tensile behaviour and fracture toughness are discussed on the basis of the formation of transcrystalline zones, orientation of EVA particles and matrix toughness of HDPE in different directions. Copyright © 2004 Society of Chemical Industry     

Structure and properties of polypropylene/high‐density polyethylene blends by solid equal channel angular extrusion

The solid equal channel angular extrusion (ECAE) process on polypropylene (PP)/high‐density polyethylene (HDPE) blends was carried out. Scanning electron microscopy (SEM) was used to observe the sample structures. Results showed that ECAE process could make PP/HDPE blends to produce orientation structure. Impact performance of ECAE‐PP/HDPE samples after ECAE process improved remarkably, especially for ECAE‐PP/HDPE (90/10)‐O whose impact strength reached 91.91 kJ/m², 18.1 times higher than that of pure PP and 11.2 times higher than that of PP/HDPE (90/10). The mechanism of enhancing between HDPE and PP was discussed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39759.     

New gasoline and gas barrier from plasticized carbon black reinforced butyl rubber/high‐density polyethylene blends

The effects of the high‐density polyethylene volume fraction on the curing characteristics and network structure of rubber blends have been studied in terms of the torque, scorch time, optimum curing time, Mooney viscosity, number of elastically effective chains, viscosity, interfacial tension, glass‐transition temperature, scanning electron microscopy, internal friction, sound velocity, acoustic attenuation, polymer–solvent interaction parameter, swelling index, and gel fraction. The applicability of the blends for gasoline barriers has been examined through the changes in the electrical resistance and volumetric swelling in gasoline versus time at room temperature. The transport mechanism of the solvent through the crosslinked butyl rubber/high‐density polyethylene blends is governed by Fickian diffusion law. The transport coefficients, namely, the diffusion coefficient, intrinsic diffusion, and permeation coefficient, have been computed. The experimental data for the permeation coefficient are in good agreement with the values calculated by Maxwell's model and far from those of Robeson's model. In addition, some thermodynamics parameters, namely, the standard entropy, standard enthalpy, and standard Gibbs free energy, have been estimated as functions of the high‐density polyethylene concentration of the butyl rubber blends. Furthermore, the applicability of butyl rubber/high‐density polyethylene composites for Freon gas barriers and antistatic charge dissipation has been examined. Finally, the mechanical properties, such as the tensile strength, hardness, stiffness, and elongation at break, of butyl rubber composites with different high‐density polyethylene concentrations have been evaluated. The increase in the mechanical properties is due to the increase in the crosslinking density and the interfacial adhesion of the blend. This proves that these new blends have important technological applications as gasoline and Freon barriers and for antistatic charge dissipation with good mechanical properties. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1237–1247, 2006     

Preparation,morphology, and mechanical properties of elastomers based on α,ω‐dihydroxy‐polydimethylsiloxane/polystyrene blends

α,ω‐Dihydroxy‐polydimethylsiloxane/polystyrene (PDMS/PS) blends were prepared by the solution polymerization of styrene (St) in the presence of α,ω ‐dihydroxy‐polydimethylsiloxane (PDMS), using toluene as solvent and benzoyl peroxide (BPO) as initiator. The PDMS/PS blends obtained by this method are a series of stable, white gums, which were vulcanized to elastomers at room temperature with methyl‐triethoxysilicane (MTES). The use level of MTES was far more than the necessary amount used to end‐link hydroxy‐terminated chains of PDMS, with the excess being hydrolyzed to crosslinked networks, which were similar to SiO₂ and acted as filler. Investigations were carried out on the elastomeric materials by extraction measurement, swelling measurement, and scanning electron microscopy. The extraction data show that at each composition the amount of soluble fraction is less than expected and the difference between experimental and theoretical values becomes more and more significant as PS content increases. This is mainly due to the grafting of PS onto PDMS and the entanglement of PS in the interpenetrating polymer network (IPN), which consists of either directly linked PDMS chains or chains linked via PS grafts and is formed by free radical crosslinking of PDMS during the radical polymerization of St. PS grafted on PDMS is insoluble and PS entangled in the IPN is difficult to extract. Both render the soluble fraction to be less than expected. As the St content in preparing PDMS/PS blends increases, the probability of grafting PS onto PDMS also increases, which may subsequently produce a higher crosslinking level of PDMS networks that linked via PS grafts by radical crosslinking. As a result, not only the amount of insoluble PS increases but also PS entangled in the IPN is more difficult to extract. Scanning electron microscopy demonstrates that the elastomer system has a microphase‐separated structure and a certain amount of PS remains in the PDMS networks after extraction, which is in accordance with the extraction data. Moreover, the mechanical properties of the elastormeric materials have been studied in detail. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3542–3548, 2004     

Thermoplastic elastomers based on epoxidized natural rubber and high‐density polyethylene blends: Effect of blend compatibilizers on the mechanical and morphological properties

Epoxidized natural rubber (ENR) with a level of epoxide groups of 20 mol % was prepared via the performic epoxidation method. It was then used to blend with high‐density polyethylene (HDPE) at various blend ratios. Three types of blend compatibilizers were prepared. These included a graft copolymer of HDPE and maleic anhydride (MA; i.e., HDPE‐g‐MA) and two types of phenolic modified HDPEs using phenolic resins SP‐1045 and HRJ‐10518 (i.e., PhSP‐PE and PhHRJ‐PE), respectively. We found that the blend with compatibilizer exhibited superior tensile strength, hardness, and set properties to that of the blend without compatibilizer. The ENR and HDPE interaction via the link of compatibilizer molecules was the polar functional groups of the compatibilizer with the oxirane groups in the ENR molecules. Also, another end of the compatibilizer molecules (i.e., HDPE segments) was compatibilizing with the HDPE molecules in the blend components. The blend with compatibilizer also showed smaller phase morphology than the blend without compatibilizer. Among the three types of the blend compatibilizer, HDPE‐g‐MA provided the blend with the greatest strength and hardness properties but the lowest set properties. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Morphology and mechanical properties of blends of linear low density polyethylene and poly(ethene‐propene‐1‐butene)

Blends of linear low density polyethylene (LLDPE) and ethene‐propene‐1‐butene copolymer (t‐PP) were obtained through mechanical mixing using a single‐screw extruder with different compositions: 20, 40, 50, 60, and 80 wt % of t‐PP. For this, two types of polyethylene were used: 1‐hexene comonomer and 1‐octene comonomer based. The same blends were prepared in a batch mixer and the torque and temperature were analyzed. The torque showed a decrease with increasing t‐PP content, indicating better processability of the mixture in comparison with LLDPE. The morphology of the blends was analyzed by SEM and showed a composition dependence. The mechanical properties of the blends were evaluated by tensile tests. The results revealed that the best properties were obtained in a 20% t‐PP blend. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1255–1261, 2006     

Preparation,morphology, and mechanical properties of elastomers based on α,ω‐dihydroxy‐polydimethylsiloxane/poly(methyl methacrylate) blends

α,ω‐Dihydroxy‐polydimethylsiloxane (PDMS)/poly(methyl methacrylate) (PMMA) blends were prepared by the radical polymerization of methyl methacrylate in the presence of PDMS, with benzoyl peroxide as the initiator. The PDMS/PMMA blends obtained by this method were a series of stable, white gums, which were vulcanized into elastomers at room temperature with methyl triethoxysilicane (MTES). The MTES dosage was much larger than the amount necessary for end‐linking the hydroxy‐terminated chains of PDMS, with the excess being hydrolyzed into crosslinked networks, which were similar to SiO₂ and acted as fillers. Investigations were carried out on the elastomeric materials by extraction measurements, swelling measurements, and scanning electron microscopy. The extraction data showed that at each composition, the sol fraction was less than expected. The extracted materials were further studied with swelling measurements, which revealed that the material obtained from an elastomer with a higher PMMA content had an apparently larger equilibrium swelling degree. Scanning electron microscopy demonstrated that the elastomer system had a microphase‐separated structure consisting of PMMA domains within a continuous PDMS matrix. Moreover, the mechanical properties of the elastomeric materials were studied in detail. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1547–1553, 2006     

Thermal and mechanical properties of linear low‐density polyethylene/low‐density polyethylene/wax ternary blends

The thermal and mechanical properties of uncrosslinked three‐component blends of linear low‐density polyethylene (LLDPE), low‐density polyethylene (LDPE), and a hard, paraffinic Fischer–Tropsch wax were investigated. A decrease in the total crystallinity with an increase in both LDPE and wax contents was observed. It was also observed that experimental enthalpy values of LLDPE in the blends were generally higher than the theoretically expected values, whereas in the case of LDPE the theoretically expected values were higher than the experimental values. In the presence of higher wax content there was a good correlation between experimental and theoretically expected enthalpy values. The DSC results showed changes in peak temperature of melting, as well as peak width, with changing blend composition. Most of these changes are explained in terms of the preferred cocrystallization of wax with LLDPE. Young's modulus, yield stress, and stress at break decreased with increasing LDPE content, whereas elongation at yield increased. This is in line with the decreasing crystallinity and increasing amorphous content expected with increasing LDPE content. Deviations from this behavior for samples containing 10% wax and relatively low LDPE contents are explained in terms of lower tie chain fractions. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1748–1755, 2005     

Mechanical and thermal properties of high‐density polyethylene toughened with glass beads

Glass beads were used to improve the mechanical and thermal properties of high‐density polyethylene (HDPE). HDPE/glass‐bead blends were prepared in a Brabender‐like apparatus, and this was followed by press molding. Static tensile measurements showed that the modulus of the HDPE/glass‐bead blends increased considerably with increasing glass‐bead content, whereas the yield stress remained roughly unchanged at first and then decreased slowly with increasing glass‐bead content. Izod impact tests at room temperature revealed that the impact strength changed very slowly with increasing glass‐bead content up to a critical value; thereafter, it increased sharply with increasing glass‐bead content. That is, the Izod impact strength of the blends underwent a sharp transition with increasing glass‐bead content. It was calculated that the critical interparticle distance for the HDPE/glass‐bead blends at room temperature (25°C) was 2.5 μm. Scanning electron microscopy observations indicated that the high impact strength of the HDPE/glass‐bead blends resulted from the deformation of the HDPE matrix. Dynamic mechanical analyses and thermogravimetric measurements implied that the heat resistance and heat stability of the blends tended to increase considerably with increasing glass‐bead content. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2102–2107, 2003     

Effect of recycled polypropylene on polypropylene/high‐density polyethylene blends

The effect of recycled PP on incompatible blends of virgin polypropylene (PP) and high‐density polyethylene (HDPE) was studied. Recycled PP from urban solid waste was extracted with methyl ethyl ketone and the compatibilizing action of the product before and after extraction was examined. The characterization of the recycled PP was performed by FTIR, NMR, and DSC analyses. Mechanical properties of the blends were evaluated. The results showed partial compatibility of the blend components, reflected in the improvement of the tensile strength and elongation. Best results were achieved by the addition of extracted recycled PP on the 50/50 PP/HDPE blends. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1305–1311, 2001     

Mechanical properties and morphology of polylactide,linear low‐density polyethylene,and their blends

Melt blending of linear low density polyethylene (LLDPE) and polylactide (PLA) was performed in an extrusion mixer with post extrusion blown film attachment with and without compatibilizer‐grafted low density polyethylene maleic anhydride. The blend compositions were optimized for tensile properties as per ASTM D 882‐91. On the basis of this, LLDPE 80 [80 wt % LLDPE and 20 wt % poly(L ‐lactic acid) (PLLA)] and MA‐g‐low‐density polyethylene 80/4 (80 wt % LLDPE, 20 wt % PLLA, and 4 phr compatibilizer) were found to be an optimum composition. The blends were characterized according to their mechanical, thermal, and morphological behavior. Fourier transform infrared spectroscopy revealed that the presence of compatibilizer enhanced the blend compatibility to some extent. The morphological characteristics of the blends with and without compatibilizer were examined by scanning electron microscopy. The dispersion of PLLA in the LLDPE matrix increased with the addition of compatibilizer. This blend may be used for packaging applications. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Studies on blends of high‐density polyethylene and polypropylene produced by oscillating shear stress field

Tensile strength and morphology of blends of high‐density polyethylene (HDPE) and polypropylene (PP) obtained by oscillating packing injection molding were investigated via Universal Testing Machine, DSC, and SAXS. Tensile strength is greatly enhanced from 24.5 MPa to more than 90 MPa for pure HDPE and for blends with PP content less than 10 wt %. There exists a sharp decrease of tensile strength when PP content is more than 10 wt %. The shear‐induced morphologies with core in the center, oriented zone surrounding the core and skin layer are observed in the cross‐section areas of the samples. Interestingly, a sharp decrease of oriented zone is seen when PP content is more than 10 wt %, associated with the sharp decrease of tensile strength. DSC result shows double melting peaks with a high‐temperature melting peak that is not present in the endotherm obtained from the central core and obtained from the samples by static packing injection molding, which indicates the existence of shish‐kebab structure in the oriented zone. However, there is no difference of crystallinity between the samples by oscillating and by static packing injection molding. SAXS was used to analyze the complicated morphologies induced by shear stress, and results show that the crystal thickness could be greatly increased under shear stress. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 58–63, 2002     

Mechanical and thermo‐physical properties of high‐density polyethylene modified with talc

The aim of this study was to examine the physical, mechanical, and thermo‐physical properties of high‐density polyethylene (HDPE) modified with talc. Different weight fractions of talc (up to 35 wt %) were compounded with an HDPE matrix containing 2.5 wt % of carbon black (CB) in a twin‐screw compounder. The composites were then processed by injection moulding to obtain specimens for testing. The results indicate that CB causes a significant decrease in the toughness, while talc not only enhances the thermal conductivity and thermo‐physical properties of the composites but can also play a role in compensating for the negative effects of CB on impact resistance. The experimental data show that the presence of CB reduces the impact resistance of HDPE by up to 34%, while addition of up to 8 wt % talc can return this value to close to that of pure HDPE. No significant effect on the composite tensile yield and fracture strength was observed for either component at all concentrations. The thermal conductivity, thermal diffusivity, and specific density values of the composites increased almost linearly, but the increase in moisture absorption in the long term showed nonlinear behavior in the concentration range of the experiment. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Structure and properties of phase change materials based on HDPE,soft Fischer‐Tropsch paraffin wax,and wood flour

Phase‐change materials based on high density polyethylene (HDPE), soft Fischer‐Tropsch paraffin wax (M3), and alkali‐treated wood flour (WF) were investigated. The blend and composite samples were prepared by melt mixing using a Brabender Plastograph, followed by melt pressing. They were characterized in terms of their morphology, as well as thermal, mechanical, thermo‐mechanical, and water absorption properties. Although SEM micrographs showed some evidence of intimate contact between the WF particles and the HDPE matrix as a result of alkali treatment, poor filler dispersion, and interfacial adhesion were also observed. Partial immiscibility of the HDPE and the M3 wax was noticed, with the WF particles covered by wax. There was plasticization of the HDPE matrix by the wax, as well as partial cocrystallization, inhomogeneity and uneven wax dispersion in the polymer matrix. The HDPE/WF/M3 wax composites were more homogeneous than the blends. The presence of wax reduced the thermal stability of the blends and composites. Both the presence of M3 wax and WF influenced the viscoelastic behavior of HDPE. The HDPE/M3 wax blends showed an increase in the interfacial amorphous content as the wax content increases, which resulted in the appearance of a β‐relaxation peak. The presence of M3 wax in HDPE reduced the mechanical properties of the blends. For the composites these properties varied with WF content. An increase in wax content resulted to a decrease in water uptake by the composites, probably because the wax covered the WF particles and penetrated the pores in these particles. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Poly(ethylene terephthalate)/poly(ethylene glycol‐co‐1,3/1,4‐cyclohexanedimethanol terephthalate)/clay nanocomposites: Mechanical properties,optical transparency,and barrier properties

Poly(ethylene terephthalate) (PET)/clay, PET/poly(ethylene glycol‐co‐1,3/1,4‐cyclohexanedimethanol terephthalate) (PETG), and PET/PETG/clay nanocomposites were fabricated using the twin‐screw extrusion technique. The spherulitic morphologies, thermomechanical, mechanical, and gas‐barrier properties, as well as the effect of clay on the transparency of the resulting nanocomposites were identified. The clay induced the heterogeneous nucleation of the nanocomposites during the cold crystallization process, thereby increasing the crystallinities and melting temperatures of the resulting nanocomposites. The incorporation of clay increased the storage moduli, Young's moduli, impact strengths, and barrier properties of the PET, PETG, and PET/PETG blend. Regarding the optical transparency, the inclusion of clay can make the crystallizable PET matrix crystalline opaque. However, the amorphous PETG maintained its transparency. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39869.     

Effect of the high‐density polyethylene melt index on the microcellular foaming of high‐density polyethylene/polypropylene blends

The effect of high‐density polyethylene (HDPE)/polypropylene (PP) blending on the crystallinity as a function of the HDPE melt index was studied. The melting temperature and total amount of crystallinity in the HDPE/PP blends were lower than those of the pure polymers, regardless of the blend composition and melt index. The effects of the melt index, blending, and foaming conditions (foaming temperature and foaming time) on the void fractions of HDPEs of various melt indices and HDPE/PP blends were also investigated. The void fraction was strongly dependent on the foaming time, foaming temperature, and blend composition as well as the melt index of HDPE. The void fraction of the foamed 30:70 HDPE/PP blend was always higher than that of the foamed 50:50 HDPE/PP blend, regardless of the melt index. The microcellular structure could be greatly improved with a suitable ratio of HDPE to PP and with foaming above the melting temperature for long enough; however, using high‐melt‐index HDPE in the HDPE/PP blends had a deleterious effect on both the void fraction and cell morphology of the blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 364–371, 2004