Relation between microstructure and glass transition temperature of poly[(methyl methacrylate)‐co‐(ethyl acrylate)]

The glass transition temperature of a series of samples of the poly[(methyl methacrylate)‐co‐(ethyl acrylate)] copolymer, synthesized at low conversion, were calculated theoretically using the equations of Barton and Johnston. The values obtained are more precise when the probabilities of the compositional diads are derived from the ¹³C NMR data instead of the classical method utilizing reactivity ratios. This can be observed more clearly when the copolymer samples are synthesized at high conversion. Introduction of configuration (tacticity) at the diad level confirms the above observations and slightly improves the calculated values of T_g compared to the initial formulae which were only taking into account the compositional sequences of the copolymer. © 2001 Society of Chemical Industry     

Decreasing miscibility with greater heterogeneity in ternary polymer blend: poly(cyclohexyl methacrylate), poly(α‐methyl styrene) and poly(4‐methyl styrene)

A ternary blend system comprising poly(cyclohexyl methacrylate) (PCHMA), poly(α‐methyl styrene) (PαMS) and poly(4‐methyl styrene) (P4MS) was investigated by thermal analysis, optical and scanning electron microscopy. Ternary phase behaviour was compared with the behaviour for the three constituent binary pairs. This study showed that the ternary blends of PCHMA/PαMS/P4MS in most compositions were miscible, with an apparent glass transition temperature (T_g) and distinct cloud‐point transitions, which were located at lower temperatures than their binary counterparts. However, in a closed‐loop range of compositions roughly near the centre of the triangular phase diagram, some ternary blends displayed phase separation with heterogeneity domains of about 1 µm. Therefore, it is properly concluded that ternary PCHMA/PαMS/P4M is partially miscible with a small closed‐loop immisciblity range, even though all the constituent binary pairs are fully miscible. Thermodynamic backgrounds leading to decreased miscibility and greater heterogeneity in a ternary polymer system in comparison with the binary counterparts are discussed. © 2003 Society of Chemical Industry     

Synthesis,characterization, and fluorescence of end‐functionalized polystyrene initiated by 4‐chloromethyl benzoic acid and ethyl 4‐chloromethyl benzenecarboxylate via ATRP

End‐functionalized polystyrene (PSt) was synthesized via atom‐transfer radical polymerization (ATRP) by using 4‐chloromethyl benzoic acid (CMBA) and the ethyl‐protected carboxylic acid, ethyl 4‐chloromethybenzenecarboxylate (ECBC), as initiators respectively. The structure of PSt proved the living‐radical polymerization. Results exhibit both ATRP initiators afforded well‐controlled polymerization with high initiator efficiencies. However, the study also shows the controllability of ATRP can be obviously influenced by using different initiator in different catalyst system. Furthermore, the terminal group of the PSt1, benzoic acid, can coordinate with Europium(III) ion to obtain the polymeric Eu(III) complex, which shows both emissions of polymer and Eu(III) ion. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Glass‐transition temperature of poly(vinylidene fluoride)‐poly(methyl acrylate) blends: Influence of aging and chain structure

The glass‐transition temperature (T_g) of the poly(vinylidene fluoride) (PVF₂)‐poly(methyl acrylate) (PMA) blends increase with aging time. The T_g versus log(time) plots are straight lines whose slope values depend on the head to head (H–H) defect content of PVF₂ samples and on the composition of the blends. The values of polymer–polymer interaction parameters (χ) increase with an increase in the H–H defect of PVF₂ for a fixed composition of the blend. Consequently, the T_g of the blend decreases with an increase in the H–H defect of the PVF₂ sample. However, after aging for longer times this decrease of the T_g with H–H defects is lower than those of the unaged blends. The possible reasons are discussed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1541–1548, 2001     

Copolymerization of N‐(4‐carboxyphenyl) itaconimide or N‐(4‐carboxyphenyl) itaconamic acid with methyl methacrylate

This paper describes the synthesis and characterization of N‐(4‐carboxyphenyl) itaconamic acid (CPA) and N‐(4‐carboxyphenyl) itaconimide (CPI) obtained by reacting itaconic anhydride with p‐aminobenzoic acid. Structural and thermal characterization of CPA and CPI was done using ¹H‐NMR, FTIR, and differential scanning calorimetry (DSC). Copolymerization of CPA or CPI with methyl methacrylate (MMA) in solution was carried out at 60 °C using azobisisobutyronitrile as an initiator and dimethyl acetamide or THF as solvent. Feed compositions having varying mole fractions of CPA or CPI ranging from 0.05–0.20 or 0.1–0.5 were taken to prepare copolymers. Copolymerizations were terminated at low percentage conversion. Structural characterization of copolymers was done by ¹H‐NMR and elemental analysis. Copolymer composition was determined using percentage nitrogen content. The reactivity ratios were r₁ (MMA) = 0.68 ± 0.06 and r₂ (CPI) = 0.46 ± 0.06. The intrinsic viscosity [η] was determined using an Ubbelohde suspension level viscometer. [η] decreased with increasing mole fraction of N‐(p‐carboxyphenyl) itaconimide or N‐(p‐carboxyphenyl) itaconamic acid in copolymers. Glass transition temperature and thermal stability of the copolymers were determined using DSC and thermogravimetric analysis, respectively. The glass transition temperature (T_g) as determined from DSC scans increased with increasing amounts of CPA or CPI in copolymers. A significant improvement in the char yield was observed upon copolymerization. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1909–1915, 2005     

Glass transition temperature of methyl methacrylate–ethyl α‐benzoyloxymethylacrylate copolymers

Poly(ethyl α‐benzoyloxymethylacrylate) (EBMA) and copolymers of methyl methacrylate (MMA) with EBMA have been prepared by free radical polymerization. Monomer precursors of ethyl α‐benzoyloxymethylacrylate have likewise been polymerized. Glass transition temperatures (T_g) of homo and copolymers have been determined by differential scanning calorimetry. The Johnston equation, which considers the influence of monomeric unit distribution on the copolymer glass transition temperature, has been used to explain the T_g behaviour. T_g12 has been calculated by the application of the Johnston equation, which gave a value markedly lower than the average value expected from the additive contribution of the T_g of the corresponding homopolymers. © 2000 Society of Chemical Industry     

Synthesis,characterization, and thermal behavior study of methyl methacrylate polymers containing 4‐carbazole substitutes

A new polymerizable monomer, [4‐(9‐ethyl)carbazolyl]methyl methacrylate ( 2 ), was synthesized by reacting of methacrylic acid and 4‐hydroxymethyl‐9‐ethyl carbazole ( 1 ) by esterification procedure in the presence of N,N′‐dicyclohexylcarbodiimide. The resulting monomer was then polymerized free‐radically to form the poly(methyl methacrylate) containing 4‐(9‐ethyl)carbazolyl pend ent groups. Also, copolymerization of monomer 2 with various acrylic monomers such as methyl methacrylate, ethyl methacrylate, methyl acrylate, ethyl acrylate, and n‐butyl acrylate by azobisisobutyronitrile as a free radical polymerization initiator gave the related copolymers in high yields. The structure of all the resulted compounds was characterized and confirmed by FTIR and ¹H NMR spectroscopic techniques. The average molecular weight of the obtained polymers was determined by gel permeation chromatography using tetrahydrofurane as the solvent. The thermal gravimetric analysis and differential scanning calorimeter instruments were used for studying of thermal properties of polymers. It was found that, with the incorporation of bulky 4‐(9‐ethyl)carbazolyl substitutes in side chains of methyl methacrylate polymers, thermal stability and glass transition temperature of polymers are increased. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4989–4995, 2006     

Synthesis and characterization of poly[4‐(2‐thiazolylazo)phenyl methacrylate]‐co‐poly(methyl methacrylate)

A new methacrylic monomer, 4‐(2‐thiazolylazo)phenylmethacrylate (TPMA) was synthesized. Copolymerization of the monomer with methyl methacrylate (MMA) was carried out by free radical polymerization in THF solution at 70 ± 0.5°C, using azobisisobutyronitrile (AIBN) as an initiator. The monomer TPMA and the copolymer poly(TPMA‐co‐MMA) were characterized by Fourier transform infrared (FTIR), ¹H nuclear magnetic resonance (NMR), and elemental analysis methods. The polydispersity index of the copolymer was determined using gel permeation chromatography (GPC). Thermogravimetric analysis (TGA) of the copolymer performed in nitrogen revealed that the copolymer was stable to 270°C. The glass transition temperature (T_g) of the copolymer was higher than that of PMMA. The copolymer with a pendent aromatic heterocyclic group can be dissolved in common organic solvents and shows a good film‐forming ability. Both the monomer TPMA and the copolymer poly (TPMA‐co‐MMA) have bright colors: orange and yellow, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2152–2157, 2007     

Controllable radical copolymerization of styrene and methyl methacrylate using 1,1,2,2‐tetraphenyl‐1,2‐bis(trimethylsilyloxy) ethane as initiator

Copolymerization of styrene (St) and methyl methacrylate (MMA) was carried out using 1,1,2,2‐tetraphenyl‐1,2‐bis (trimethylsilyloxy) ethane (TPSE) as initiator; the copolymerization proceeded via a “living” radical mechanism and the polymer molecular weight (M_w) increased with the conversion and polymerization time. The reactivity ratios for TPSE and azobisisobutyronitrile (AIBN) systems calculated by Finemann–Ross method were r_St = 0.216 ± 0.003, r_MMA= 0.403 ± 0.01 for the former and r_St= 0.52 ± 0.01, r_MMA= 0.46 ± 0.01 for the latter, respectively, and the difference between them and the effect of polymerization conditions on copolymerization are discussed. Thermal analysis proved that the copolymers obtained by TPSE system showed higher sequence regularity than that obtained by the AIBN system, and the sequence regularity increased with the content of styrene in copolymer chain segment. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1474–1482, 2001     

One‐pot synthesis of self‐stabilized and carboxyl‐functionalized fluorescent poly(methyl methacrylate) microspheres covalently dyed with tris(8‐hydroquinolinato)aluminium by dispersion polymerization

The dispersion polymerization of methyl methacrylate (MMA) with fluorescent monomer tris[2‐((8‐hydroxyquinolin‐5‐yl)methoxy)ethyl methacrylate]aluminium (Al‐HQHEMA) was investigated to obtain fluorescent microspheres under varying conditions (such as composition of dispersion medium, and content of stabilizer polyvinylpyrrolidone (PVP) and Al‐HQHEMA) in methanol–water at 70 °C with 2,2′‐azoisobutyronitrile as the initiator. Fluorescent microspheres with particle size of 2.039 µm and uniformity of 0.171 were obtained under the following conditions: methanol–water, 7:3 (v/v); PVP, 15 wt% of MMA; Al‐HQHEMA solution, 1.5 mL. Maleic monoester of monomethoxyl poly(ethylene glycol) (Mal‐MPEG) was used as a comonomer to simultaneously incorporate carboxyl groups and PEG chains. With Mal‐MPEG, no aggregation was observed in the measurements of particle size and size distribution for the obtained microspheres after cleaning off PVP, indicating that self‐stabilized fluorescent microspheres were obtained. While without Mal‐MPEG, obvious aggregation was observed. The determination of surface carboxyl content using aqueous acid–base titration showed that most of the carboxyl groups of Mal‐MPEG were located on the surface of the microspheres. © 2015 Society of Chemical Industry     

Variations of the glass‐transition temperature in the imidization of poly(styrene‐co‐maleic anhydride)

The imidization of poly(styrene‐co‐maleic anhydride) (SMA) was conducted, and the glass‐transition temperatures (T_g's) of the resulting products were measured with differential scanning calorimetry. The contributions from functional groups of maleic anhydride, N‐phenylmaleamic acid, and N‐phenylmaleimide to T_g were examined. T_g increased in the order of SMA < styrene–N‐phenyl maleimide copolymer < styrene–N‐phenyl maleamic acid copolymer and followed the Fox equation. T_g of the imidized products of SMA could be controlled by the conversions of both ring‐opening and ring‐closing reactions. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2418–2422, 2007     

Synthesis and thermal properties of poly(methyl methacrylate)‐poly(L‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer

Poly(methyl methacrylate)‐poly(L ‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer was prepared using atom transfer radical polymerization (ATRP). The structure and properties of the copolymer were analyzed using infrared spectroscopy, gel permeation chromatography, nuclear magnetic resonance (¹H‐NMR, ¹³C‐NMR), thermogravimetry, and differential scanning calorimetry. The kinetic plot for the ATRP of methyl methacrylate using poly(L ‐lactic acid) (PLLA) as the initiator shows that the reaction time increases linearly with ln[M]₀/[M]. The results indicate that it is possible to achieve grafted chains with well‐defined molecular weights, and block copolymers with narrowed molecular weight distributions. The thermal stability of PLLA is improved by copolymerization. A new wash‐extraction method for removing copper from the ATRP has also exhibits satisfactory results. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of tacticity of poly(methyl methacrylate) on interfacial region with silica in polymer nanocomposite

The effect of tacticity on the interfacial region between poly(methyl methacrylate) (PMMA) and silica in a PMMA/silica nanocomposite was investigated by differential scanning calorimetry (DSC), Fourier-transform infrared spectroscopy (FT-IR), and X-ray diffraction (XRD). The glass transition temperature (T_g) values of the syndiotactic (st-) and atactic (at-) PMMA/silica nanocomposites are higher than those of the neat PMMA. Conversely, the T_g of the isotactic (it-) PMMA/silica nanocomposite is slightly higher than that of the neat it-PMMA. DSC and XRD results suggest that the restriction of the PMMA chain mobility in the silica nanoparticle interfacial region heightens as the syndiotactic content increases. FT-IR results show that this phenomenon is caused by the interaction between the carbonyl group of PMMA and the silanol group on the silicon dioxide surface. Therefore, it can be concluded that the syndiotactic-rich PMMA has a significantly different molecular mobility from that of the neat PMMA in the interfacial region with silica nanoparticle surface than isotactic-rich PMMA.     

Free radical copolymerization of N,N‐dimethylaminoethyl methacrylate with styrene and methyl methacrylate: monomer reactivity ratios and glass transition temperatures

BACKGROUND: The properties of copolymers depend strongly on their composition; therefore in order to tailor some for specific applications, it is necessary to control their synthesis, and, in particular, to know the reactivity ratios of their constituent monomers. Free radical copolymerizations of N,N‐dimethylaminoethyl methacrylate (DMAEM) with styrene (ST) and methyl methacrylate (MMA) in toluene solution using 1‐di(tert‐butylperoxy)‐3,3,5‐trimethylcyclohexane as initiator at 70 °C were investigated. Monomer reactivity ratios were determined for low conversions using both linear and nonlinear methods. RESULTS: For the DMAEM/ST system the average values are r₁ = 0.43 and r₂ = 1.74; for the DMAEM/MMA system the average values are r₁ = 0.85 and r₂ = 0.86. The initial copolymerization rate, R_p, for DMAEM/ST sharply decreases as the content of ST in the monomer mixture increases up to 30 mol% and then attains a steady value. For the DMAEM/MMA copolymerization system the composition of the feed does not have a significant influence on R_p. The glass transition temperatures (T_g) of the copolymers were determined calorimetrically and calculated using Johnston's sequence length method. A linear dependence of T_g on copolymer composition for both systems is observed: T_g increases with increasing ST or MMA content. CONCLUSION: Copolymerization reactivity ratios enable the design of high‐conversion processes for the production of copolymers of well‐defined properties for particular applications, such as the improvement of rheological properties of lubricating mineral oils. Copyright © 2009 Society of Chemical Industry     

Synthesis and characterization of soluble poly(arylene ether ketone)s with high glass transition temperature based on 3,6‐bi(4‐fluorobenzoyl)‐N‐alkylcarbazole

3,6‐bi(4‐fluorobenzoyl)‐N‐methylcarbazole and 3,6‐bi(4‐fluorobenzoyl)‐N‐ethylcarbazole were synthesized and used to prepare poly(arylene ether ketone)s (PAEKs) with high glass transition temperatures (T_g) and good solubility. High molecular weight amorphous PAEKs were prepared from these two difluoroketones with hydroquinone, phenolphthalein, 9,9‐bis(4‐hydroxyphenyl)fluorene and 4‐(4‐hydroxylphenyl)‐2,3‐phthalazin‐1‐one, respectively. All these polymers presented high thermal stability with glass transition temperatures being in the range 239–303 °C and a 5% thermal weight loss temperature above 460 °C. Compared with the T_g of phenolphthalein‐based PAEK (PEK‐C), fluorene‐based PAEK (BFEK) and phthalazinone‐based PAEK (DPEK) not containing a carbazole unit, these polymers presented a 30–50 °C increase in T_g. Meanwhile, PAEKs prepared from N‐ethylcarbazole difluoroketone showed good solubility in ordinary organic solvents, and all polymers exhibited excellent resistance to hydrochloric acid (36.5 wt%) and sodium hydroxide (50 wt%) solutions. In particular, phthalazinone‐based PAEK bearing N‐ethylcarbazole afforded simultaneously a T_g of 301 °C with good solubility. Tensile tests of films showed that these polymers have desirable mechanical properties. The carbazole‐based difluoroketones play an important role in preparing soluble PAEKs with high T_g by coordinating the relationship between chain rigidity resulting from the carbazole unit and chain distance from the side alkyl. © 2014 Society of Chemical Industry     

Preparation and glass transition temperature of hyperbranched poly[allyl methyl maleate‐co‐N‐propyl maleimide]

The kinetics and molecular weight averages of the hyperbranched polymers formed by the alternating copolymerization of equimolar allyl methyl maleate (AMM) and N‐n‐propyl maleimide (PMI) were investigated. The yields, molecular weight averages, and polydispersity indices as well as the branching degrees of the produced copolymers increased with increasing initiator concentrations and prolonged polymerization time. The trends of the experimental molecular weights as determined by size exclusion chromatography were in good agreement with the theoretical predictions. The molecular weight distribution indices fit the curve given by M_w/M_n = 1/(1‐x_D), and the molecular weights fit the curve given by M_w = 4076/(1‐x_D)², where x_D was the conversion of vinyl groups. DSC studies demonstrated a nonlinear relation of T_g values to the reciprocal of molecular weight (M), and T_g values decreased with the increase of molecular weight. For the T_g values of highly branched polymers in high molecular weight range, a relation of T_g = T + k/M was obtained, where T was obtained by extrapolating to infinite molecular weight and k was a constant. T was 136°C, and k = 2.9 for this work. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1941–1947, 2005     

Structural investigations of (9‐ethyl‐carbazol‐6‐yl) methyl methacrylate/methyl acrylate copolymers using two‐dimensional NMR spectroscopy

(9‐Ethyl‐carbazol‐6‐yl) methyl methacrylate/methyl acrylate (E/A) copolymers of different compositions were prepared by solution polymerization by varying the molar infeed ratio, using AIBN as initiator at 60°C. The reactivity ratios calculated by Kelen–Tudos (KT) method were found to be r_E = 1.16 ± 0.02 and r_A = 0.69 ± 0.01 whereas those calculated from RREVM method were found to be r_E = 1.18 and r_A = 0.68. The molecular weights (M_w) and polydispersity index (PDI, M_w/M_n) were determined using gel permeation chromatography (GPC). Glass transition temperatures (T_g) for different compositions of E/A copolymers were determined using differential scanning calorimetry (DSC). Copolymer molar outfeed ratio (F_E) was calculated from ¹H NMR spectra. The α‐methyl, methine, backbone methylene, and quaternary carbon resonance signals of the copolymers were distinguished using ¹³C{¹H}, DEPT‐45, ‐90, and ‐135 NMR techniques. The α‐methyl and β‐methylene showed compositional and configurational sensitivity up to pentad and tetrad level, respectively, whereas methine showed only compositional sensitivity up to pentad level. Unambiguous assignments for ¹H and ¹³C{¹H} NMR spectra were done by correlating 1D (¹H, ¹³C{¹H}, DEPT) and 2D (HSQC, TOCSY) NMR data. The spectral assignments for carbonyl region were done by studying higher bond order couplings by heteronuclear multibond correlation (HMBC) spectra. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5595–5606, 2006     

Polymerization of acrylonitrile catalyzed by single yttrium tris(2,6‐di‐tert‐butyl‐4‐methyl phenolate)

Polymerization of acrylonitrile was carried out using yttrium tris(2,6‐di‐tert‐butyl 4‐methyl‐phenolate) (Y(OAr)₃) as single component catalyst for the first time. The effects of concentrations of the monomer and catalyst, kinds of rare earth element and solvent, as well as temperature and polymerization time were investigated. The overall activation energy of polymerization in n‐hexane and THF mixture is 18.3 kJ mol^?1. Polyacrylonitriles (PANs) obtained by using Y(OAr)₃ in n‐hexane and THF mixture at 50 °C are predominantly atactic, while yellow PANs obtained in DMF under the same conditions have a syndiotactic‐rich configuration (>50%), and their highly branched and/or cyclized structures have also been found. © 2002 Society of Chemical Industry