BIMS/filler interactions. II. Effects of filler concentration and BIMS structure

Brominated isobutylene para‐methylstyrene (BIMS) elastomer is a terpolymer of isobutylene, para‐methylstyrene (PMS), and para‐bromomethylstyrene (BrPMS). Viscoelastic measurements have been used to characterize the blends of this BIMS elastomer with different concentrations of a carbon black (CB) filler, N234. Data in the low temperature/high frequency region suggest that N234 at a concentration less than or equal to 15 vol % in BIMS appears not to affect the T_g of BIMS although a slight increase in relaxation time in the transition zone is observed. Also, the effects of BrPMS and PMS contents in BIMS on BIMS/N234 CB interactions have been qualitatively investigated by using the bound rubber measurements. To assess BIMS/CB interactions with reference to diene rubber/CB interactions, mixing of BIMS with various amounts of a polybutadiene rubber in the presence of CB has been performed. Atomic force microscopy and image processing have been employed to quantify filler phase distributions in these blends for a practical ranking of polymer/CB interactions. Preferential partition of CB in the BIMS or BR phase depends on the BrPMS content in BIMS. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 659–667, 2006     

Selective wetting and dispersion of filler in rubber composites under influence of processing and curing additives

The present work highlighted the effect of commonly used processing and curing additives on the wetting and dispersion kinetics of filler like silica and carbon black (CB) in some examples using the methods like the wetting concept and online measured electrical conductance. The adsorption of additives and mono-functional silane on silica surface increases the wetting speed of silica in single compound of nitrile butadiene rubber (NBR), natural rubber (NR) and styrene butadiene rubber (SBR) compounds. In rubber blend, for instance NBR/NR, the extent of filler surface fraction wetted by each blend component is strongly dependent on the additive/silica and silane/silica ratio r. A model based on the surface tension data of rubber components and filler (Z-model) was used for prediction of the selective filler wetting at a thermodynamic equilibrium state. By combining the experimental results from the wetting concept and theoretical prediction from the Z-model the silica surface tension changed during mixing can be characterized. It quantitatively describes the deactivation of the silanol groups on the silica surface by adsorbed additives. The effect of adsorption of additives on filler dispersion was exemplarily demonstrated on CB filled SBR compounds by means of the method of online measured electrical conductance. The influence of additives on the CB dispersion in low styrene-content SBR mixtures is much more pronounced than that in high styrene-content SBR mixtures.     

Preparation and properties of styrene‐butadiene rubber nanocomposites blended with carbon black‐graphene hybrid filler

Graphene has become an attractive reinforcing filler for rubber materials, but its dispersion in rubber is still a big challenge. In this work, a novel carbon black‐reduced graphene (CB‐RG) hybrid filler was fabricated and blended with styrene‐butadiene rubber (SBR) via simple two‐roll mill mixing. The prepared CB‐RG hybrids had a microstructure with small CB agglomerates adsorbed onto graphene surfaces. CB acted as a barrier preventing the RG sheets from restacking even after drying. Homogeneous dispersion of graphene sheets in SBR matrix was observed by the mechanical mixing method based on the application of the CB‐RG hybrid fillers. Dynamic mechanical analysis showed that Tg of the SBR/CB‐RG blend was higher than that of the SBR/CB blend indicating strong interfacial interactions between RG and SBR due to the high surface area of graphene and the π‐π interaction between SBR and graphene. The tensile properties of SBR/CB‐RG composites improved significantly and the volume resistivity decreased compared with the SBR/CB blends. The thermal stability of SBR composites filled with CB and CB‐RG showed slight difference. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41309.     

Influence of 1,2‐unit contents on retraction behaviors of SBR vulcanizates

Styrene‐butadiene rubber (SBR) has four different repeat units of styrene, cis‐1,4‐, trans‐1,4‐, and 1,2‐uints. Influence of the 1,2‐unit content on the retraction behaviors of SBR vulcanizates reinforced with silica or carbon black was studied. The retraction behaviors were compared in terms of the filler systems and the microstructures of SBR. The silica‐filled vulcanizates containing a coupling agent showed nearly the same retraction behaviors as the carbon black‐filled ones, but the silica‐filled vulcanizates without a coupling agent were recovered slower than the carbon black‐filled ones. The vulcanizates with lower 1,2‐unit content started to recover at lower temperature than that with higher 1,2‐unit content. The recovery rate increased with increase of the 1,2‐unit content of SBR. The experimental results were explained with the polymer‐filler interactions, filler dispersion, glass transition temperature, and modulus. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:4707–4711, 2006     

Norbornylized soybean oil as a sustainable new plasticizer for rubbers with hybrid fillers

Carbon black (CB) and precipitated silica are two major reinforcing fillers in rubbers. CB/silica hybrid filler is also widely used in rubbers to provide balanced properties. CB/silica‐hybrid‐filler‐filled styrene‐butadiene rubber (SBR) containing naphthenic oil (NO), soybean oil (SO) and norbornylized SO (NSO) was investigated. The swelling and curing behavior and rheological, mechanical, thermal, aging and dynamic properties were studied and compared with earlier reported data on CB‐ or silica‐filled SBR. NSO provides better scorch safety and faster cure than SO. Compared with NO, the addition of SO and NSO enhances the thermal stability and aging resistance of SBR vulcanizates. SBR/NSO vulcanizates with hybrid filler exhibit a higher tensile and tear strength than SBR/NO and SBR/SO vulcanizates. A synergistic effect in the abrasion resistance of vulcanizates containing the hybrid filler is observed. An increase of sulfur content in the hybrid‐filler‐filled SBR/NSO vulcanizates provides further improvement in abrasion resistance, wet traction and rolling resistance. © 2017 Society of Chemical Industry     

Influence of the filler type on the rupture behavior of filled elastomers

This work is devoted to the rupture behavior of elastomers filled with carbon black (CB) or silica. Two elastomers have been studied: one which crystallizes under strain, natural rubber (NR), and another one which does not crystallize, styrene butadiene rubber (SBR). The study of the crack propagation of Single Edge Notched specimen (SENT) during stretching at different speeds focuses on the crack initiation and crack deviation phenomenon. This deviation is of main importance in the materials crack resistance as it leads to a large increase in the energy needed for rupture. The deviation in filled or unfilled NR is controlled by crystallization, which is a slow process. In unfilled SBR, deviation is controlled by polymer chain orientation, which is hindered by relaxation mechanisms. The introduction of fillers promotes strain amplification, and strain anisotropy in the crack tip region of the notched samples, and therefore crack deviation. In term of energy density at break of the SBR composites, the SBR filled with silica treated with a covering agent is the most efficient. Thus, a weak interface between the silica and SBR promotes better rupture properties. When comparing Silica and CB filled NR, the highest strain energy to rupture is also obtained with silica. This might be due to the weaker filler‐matrix interface for silica. Thus, these results evidence the kinetic aspect of the rupture, and of the mechanisms it involves: the polymer relaxation, the crystallization (for NR), and the filler‐matrix interaction and decohesion, all of them being strongly interrelated. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Properties of styrene butadiene rubber (SBR)/recycled acrylonitrile butadiene rubber (NBRr) blends: The effects of carbon black/silica (CB/Sil) hybrid filler and silane coupling agent,Si69

The recycling or reuse of waste rubber by means of blending together with polymeric materials in addition of filler such as hybrid carbon black and silica (CB/Sil) to a polymer system can provides an opportunity to explore alternative product specifications. Therefore, in this work the investigation of recycled rubber blends based on styrene butadiene rubber/recycled acrylonitrile butadiene rubber (SBR/NBRr) blends reinforced with 50/0, 40/10, 30/20, 20/30, 40/10, 0/50 phr of carbon black/silica (CB/Sil) hybrid filler treated with and without silane coupling agent (Si69) were determined. Cure characteristics, tensile properties, and morphological behavior of selected SBR/NBRr blends at a fix 85/15 blend ratio were evaluated. Results showed that, cure time t₉₀, minimum torque (M_L), and maximum torque (M_H) of CB/Sil hybrid fillers filled SBR/NBRr blends with and without Si69 increased as silica content increased. However, t₉₀ and M_L of SBR/NBRr blends with Si69 were lower than without Si69 except for (M_H). The optimum scorch time (t_s2) of SBR/NBRr blends with and without Si69 was obtained at 30/20 phr of CB/Sil hybrid filler. However, t_s2 of SBR/NBRr blends with Si69 were longer than SBR/NBRr blends without Si69. The incorporation of Si69 has improved the tensile properties [(tensile strength, elongation at break (E_b), stress at 100% elongation (M100), and stress at 300% elongation (M300)] of CB/Sil hybrid fillers filled SBR/NBRr blends. These properties were influenced by the degree of crosslinked density as the silica content is increased. Scanning electron microscopy (SEM) of the tensile fracture surfaces indicated that, with the addition of Si69 improved the dispersion of hybrid fillers and NBRr in SBR/NBRr matrix. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Experimental testing of the polymer–filler gel formation theory. II.

In Part I of the present article predictions of the polymer–filler gel formation theory were tested experimentally using fine-particle silica in natural rubber (NR) and in styrene–butadiene rubber (SBR). Part II brings a more detailed experiment–theory comparison using carbon blacks differing in specific surface area and structure, graphitized blacks, fume silica, and surface-modified (hydrophobized) fume silica. In the region of low and medium filler concentration c, the c-dependence of the fraction G of polymer in polymer–filler gel, of the fraction B of total filler-bound polymer, of the fraction w_disp of solvent-dispersed filler particles were found to be correctly predicted by the theory. The effect of filler characteristics and of the method of its incorporation into the polymer on the values of the adjustable parameters of the theory (filler surface adsorptivity, D, and filler particles connectivity, f) was determined and is discussed. In the region of very high c increasing positive deviations of D from the low-c behavior were observed and an explanation for this effect is proposed. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 95–107, 1998     

Thermal and scanning electron microscopy/energy‐dispersive spectroscopy analysis of styrene–butadiene rubber–butadiene rubber/silicon dioxide and styrene–butadiene rubber–butadiene rubber/carbon black–silicon dioxide composites

Silica as a reinforcement filler for automotive tires is used to reduce the friction between precured treads and roads. This results in lower fuel consumption and reduced emissions of pollutant gases. In this work, the existing physical interactions between the filler and elastomer were analyzed through the extraction of the sol phase of styrene–butadiene rubber (SBR)–butadiene rubber (BR)/SiO₂ composites. The extraction of the sol phase from samples filled with carbon black was also studied. The activation energy (E_a) was calculated from differential thermogravimetry curves obtained during pyrolysis analysis. For the SBR–BR blend, E_a was 315 kJ/mol. The values obtained for the composites containing 20 and 30 parts of silica per hundred parts of rubber were 231 and 197 kJ/mol, respectively. These results indicated an increasing filler–filler interaction, instead of filler–polymer interactions, with respect to the more charged composite. A microscopic analysis with energy‐dispersive spectroscopy showed silica agglomerates and matched the decreasing E_a values for the SBR–BR/30SiO₂ composite well. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2273–2279, 2005     

Properties of silica‐filled styrene‐butadiene rubber compounds containing acrylonitrile‐butadiene rubber: The influence of the acrylonitrile‐butadiene rubber type

Because silica has strong filler‐filler interactions and adsorbs polar materials, a silica‐filled rubber compound exhibits poor dispersion of the filler and poor cure characteristics in comparison with those of a carbon black‐filled rubber compound. Acrylonitrile‐butadiene rubber (NBR) improves filler dispersion in silica‐filled styrene‐butadiene rubber (SBR) compounds. The influence of the NBR type on the properties of silica‐filled SBR compounds containing NBR was studied with NBRs of various acrylonitrile contents. The composition of the bound rubber was different from that of the compounded rubber. The NBR content of the bound rubber was higher than that of the compounded rubber; this became clearer for NBR with a higher acrylonitrile content. The Mooney scorch time and cure rate became faster as the acrylonitrile content in NBR increased. The modulus increased with an increase in the acrylonitrile content of NBR because the crosslink density increased. The experimental results could be explained by interactions of the nitrile group of NBR with silica. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 385–393, 2002     

Improvement of properties of silica‐filled styrene–butadiene rubber compounds using acrylonitrile–butadiene rubber

Since silica has strong filler–filler interactions and adsorbs polar materials, a silica‐filled rubber compound has a poor dispersion of the filler and poor cure characteristics. Improvement of the properties of silica‐filled styrene–butadiene rubber (SBR) compounds was studied using acrylonitrile–butadiene rubber (NBR). Viscosities and bound rubber contents of the compounds became lower by adding NBR to the compound. Cure characteristics of the compounds were improved by adding NBR. Physical properties such as modulus, tensile strength, heat buildup, abrasion, and crack resistance were also improved by adding NBR. Both wet traction and rolling resistance of the vulcanizates containing NBR were better than were those of the vulcanizate without NBR. The NBR effects in the silica‐filled SBR compounds were compared with the carbon black‐filled compounds. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1127–1133, 2001     

ESR study of silica‐filled SBR with different rubber/filler interactions

Silica‐filled styrene–butadiene rubber (SBR) unvulcanizates and their vulcanizates with different rubber/filler interactions were prepared by using several kinds of coupling agents. Tensile tests and electron spin resonance (ESR) measurements were carried out for both unvulcanized and vulcanized samples to get information on the effects of filler/rubber interactions on the breakdown of carbon–carbon (C? C) linkages in SBR and carbon–sulfur (C? S? C, C? S? S? C) linkages at the crosslinked points between rubber and sulfur by a tensile force. The combination of ESR results and stress–strain data suggested that with increasing the mechanical energy applied to the samples by the stretching, the carbon–sulfur linkages around silica particles were broken first, followed by the breakdown of carbon–sulfur and C? C linkages in the rubber matrix. The assignment of ESR spectrum was also discussed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Structure–property relationships of silica/silane formulations in natural rubber,isoprene rubber and styrene–butadiene rubber composites

The mechanical performance of natural rubber (NR), synthetic poly-isoprene rubber (IR), and styrene–butadiene rubber (SBR) composites filled with various silica/silane systems is investigated. The results are analyzed by referring to micro-mechanical material parameters, which quantify the morphological and structural properties of the polymer and filler network. These are obtained from fits with the dynamic flocculation model (DFM) describing the strongly nonlinear quasi-static stress–strain response of filler-reinforced elastomers as found from multihysteresis measurements of the investigated compounds. We focus on the reinforcement mechanisms of silica compounds with coupling and covering silane, respectively. The fitted material parameters give hints that the coupling silane provides a strong chemical polymer–filler coupling, which is accompanied by improved strength of filler–filler bonds for all three rubbers types. This may result also from the chemical coupling of short chains bridging adjacent silica particles. It implies larger stress values for the coupling silane and, in the case of NR and IR, a more pronounced “Payne effect” compared to the covering silane. In contrast, for SBR, the coupling silane delivers a lower Payne effect, which is explained by differences in the compatibility between rubber type and silane-grafted silica surface. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48435.     

Effect of low molecular weight polybutadiene as processing aid on properties of silica‐filled styrene–butadiene rubber compounds

Because silica has strong filler–filler interactions, a silica‐filled rubber compound shows a poor filler dispersion compared to a carbon black‐filled one. Improvement of the filler dispersion in silica‐filled styrene–butadiene rubber (SBR) compounds was studied using low molecular weight polybutadiene (liquid PBD) with the high content of 1,2‐unit. By adding the liquid PBD to the silica‐filled SBR compound, the filler dispersion and flow property are improved. The cure time and cure rate become faster as the 1,2‐unit content of the liquid PBD increases for the compounds containing the liquid PBD. The crosslink density increases linearly with increase in the 1,2‐unit content of the liquid PBD. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3135–3140, 2003     

Impacts of interfacial interaction on properties of melamine formaldehyde microsphere/rubber: I. filler dispersion and curing dynamic

Melamine formaldehyde microsphere (MF) was incorporated into nitrile butadiene rubber (NBR) and styrene butadiene rubber (SBR), respectively. The interaction between MF and rubber and effects of interfacial interaction on the dispersion of filler in rubber matrix, dynamic mechanical analysis, vulcanisation characteristics and kinetics were studied. The results showed that MF interacted with NBR through hydrogen bonds while there had no observed interaction between MF and SBR. The parameter b of MF/NBR calculated by the ratio of modulus and strains increased significantly, which demonstrated further the strong interaction between MF and NBR. For MF/SBR system, however, the parameter b changed slightly with little polymer–filler interaction. The Scanning Electron Microscope images released that strong polymer–filler interaction caused the uniform dispersion of MF in NBR matrix. The vulcanisation of MF/rubber was fitted by Ghoreishy’s model, and the addition of MF increased the rate of curing, shear modulus of compound and activity energy.     

Shape controlled spherical (0D) and rod-like (1D) silica nanoparticles in silica/styrene butadiene rubber nanocomposites: Role of the particle morphology on the filler reinforcing effect

Silica/styrene butadiene rubber (SBR) nanocomposites were prepared by blending method using shape-controlled spherical and rod-like nanoparticles with different aspect ratios as filler for the rubber reinforcement. The differently shaped silica particles were synthesized by sol–gel method using tetraethoxysilane (TEOS) and (3-mercaptopropyl) trimethoxysilane (MPTSM) as silica precursors, and cetyltrimethylammonium bromide (CTAB) as structure directing agent. This strategy allowed to study the influence of the particle morphology on the reinforcing effect independently of the silica surface chemistry and considering the aspect ratio as the only geometrical variance. Spherical and anisotropic rod-like particles, dispersed in the nanocomposites, formed a network of particles bridged by thin rubber layers throughout the SBR matrix. Moreover, differently oriented domains of aligned rods are observed when the aspect ratio of particles increases and is ≥2. Dynamic-mechanical properties demonstrated that the rod-like particles with the higher aspect ratio provided stronger reinforcement of the rubber. This was related to the self-alignment of the anisotropic particles and to the consequent larger filler/polymer interface, compared to that of spherical ones.     

Kinetics of the phase selective localization of silica in rubber blends

The Fourier transformed infrared (FTIR) spectroscopy on the rubber‐filler gel has been used as a tool for the quantitative characterization of the phase selective silica localization in styrene butadiene rubber (SBR)/natural rubber (NR) blends. The so‐called rubber‐layer L was introduced to describe the selective wetting behavior of the rubber phases to the filler. SBR/NR blends filled with silica were the focus of the experimental investigation. NR shows a higher wetting rate than SBR. Silane addition does not affect the wetting of NR but slowdowns the wetting of SBR. With increasing chamber temperature the value of the rubber‐layer L of all mixtures increases owing to the different thermal activated rubber‐filler bonding processes. Using the wetting concept the kinetics of silica localization in the phases of heterogeneous rubber blends was characterized. Because of the higher wetting rate of the NR component, in the first stage of mixing of NR/SBR blends more silica is found in the NR phase than in the SBR phase. In the next stage, silica is transferred from the NR phase to the SBR phase until the loosely bonded components of NR rubber‐layer are fully replaced by SBR molecules. POLYM. COMPOS., 31:1701–1711, 2010. © 2010 Society of Plastics Engineers.     

Styrene butadiene rubber/epoxidized natural rubber/carbon filler nanocomposites: microstructural development and cure characterization

Microstructural development of elastomeric nanocomposites based on (50/50 wt%) styrene butadiene rubber (SBR) and epoxidized natural rubber (50 mol% epoxidation, ENR50) as the rubber matrix including two types of carbon fillers, carbon black (CB) and functionalized multiwall carbon nanotube (NH₂-MWCNT), which were prepared through melt mixing, was studied. The results from FTIR analysis show that there is interaction between functional groups on MWCNT surface and the rubber chains. The AFM analysis also indicates good dispersion of filler particles in the rubber phases. FESEM images from cryo-fractured surface of samples have revealed that nanotubes were rarely pulled out of matrix and their diameter increased, resulting from good interaction between MWCNTs and rubber chains. The DMA results confirm good interfacial interaction between them. Furthermore, the reduced difference between the two T_gs of phases (ΔT_g) shows that the incorporation of 3 phr MWCNT into the blend leads to increment in rubber phase compatibility but at higher MWCNT content (5 phr) due to lower Mooney viscosity of SBR phase, MWCNTs tend to remain in this phase. The bound rubber was adopted to characterize the polymer–filler interaction, showing that bound rubber content has an increasing trend with increasing in fillers content. The cure rheometric studies reveal that MWCNTs accelerate the cure process due to the presence of amine groups on the nanotube surface. In addition, the mechanical properties of samples show an increasing trend by increasing nano-filler content.

     

Dynamic properties of star‐shaped,solution‐polymerized styrene–butadiene rubber and its cocoagulated rubber‐filled with silica/carbon black

The dynamic properties, including the dynamic mechanical properties, flex fatigue properties, dynamic compression properties, and rolling loss properties, of star‐shaped solution‐polymerized styrene–butadiene rubber (SSBR) and organically modified nanosilica powder/star‐shaped styrene–butadiene rubber cocoagulated rubber (N‐SSBR), both filled with silica/carbon black (CB), were studied. N‐SSBR was characterized by ¹H‐NMR, gel permeation chromatography, energy dispersive spectrometry, and transmission electron microscopy. The results show that the silica particles were homogeneously dispersed in the N‐SSBR matrix. In addition, the N‐SSBR/SiO₂/CB–rubber compounds' high bound rubber contents implied good filler–polymer interactions. Compared with SSBR filled with silica/CB, the N‐SSBR filled with these fillers exhibited better flex fatigue resistance and a lower Payne effect, internal friction loss, compression permanent set, compression heat buildup, and power loss. The nanocomposites with excellent flex fatigue resistance showed several characteristics of branched, thick, rough, homogeneously distributed cross‐sectional cracks, tortuous flex crack paths, few stress concentration points, and obscure interfaces with the matrix. Accordingly, N‐SSBR would be an ideal matrix for applications in the tread of green tires. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40348.