Elastic properties of adhesive polymers. I. Polymer films by means of electronic speckle pattern interferometry

The elastic modulus and Poisson's ratio of seven different polymers frequently used as wood adhesives and/or matrix polymers in wood‐ and natural‐fibre‐reinforced composites, respectively, were determined by means of tensile tests. Specimen deformation during testing was measured by means of a mechanical extensometer and an electronic speckle pattern interferometry system, respectively. The results from both methods show an excellent correlation for the elastic modulus. The elastic moduli of the studied polymers cover a wide range from 0.47 GPa for polyurethane to 6.3 GPa for melamine–urea–formaldehyde, whereas Poisson's ratios show less variability. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3936–3939, 2007     

In situ investigation of tensile behavior of Cf/SiC mini composites

This study presents an in depth analysis over the in situ tensile behavior of C_f/SiC mini composites. As part of the process, the matrix crack spacing at saturation was determined by the in situ x-ray microtomography tensile test and the test results were compared with others obtained by in situ optical microscope tensile test and scanning electron microscopy scan. Moreover, elastic modulus of fiber and matrix as well as interface shear stress were identified by the indirect method and in situ modulus of C fibers and SiC matrix were also measured by the nanoindentation test, showing outcomes much lower than those identified by indirect method. The in situ property parameters measured by in situ XCT tensile test and identified by the indirect method were substituted into the shear-lag model to predict the stress-strain responses of C_f/SiC mini composites and the predicted results agrees well with the experimental data, while there exists large deviation between the stress-strain response predicted by using the in situ modulus of C fibers tested by nanoindentation and the experimental data, which indicates that in situ modulus of C fibers tested by nanoindentation tests cannot be utilized to model the tensile stress-strain responses due to the possible asymmetry of tension and compression of C fibers.     

Evaluation of dynamic elastic properties of wood‐filled polypropylene composites

Dynamic modulus of elasticity (MoE) and shear modulus of wood‐filled polypropylene composite at various filler contents ranging from 10% to 50% was determined from the vibration frequencies of disc‐shaped specimens. Wood filler was used in both fiber form (pulp) and powder form (wood flour). A novel compatibilizer, m‐isopropenyl‐α,α‐dimethylbenzyl‐isocyanate(m‐TMI) grafted polypropylene with isocyanate functional group was used to prepare the composites. A linear increase in dynamic MoE, shear modulus, and density of the composite was observed with the increasing filler content. Between the two fillers, wood fiber filled composites exhibited slightly better properties. At 50% filler loading, dynamic MoE of the wood fiber filled composite was 97% higher than that of unfilled polypropylene. Halpin‐Tsai model equation was used to describe the changes in the composite modulus with the increasing filler content. The continuous improvement in elastic properties of the composites with the increasing wood filler is attributed to the effective reinforcement of low‐modulus polypropylene matrix with the high‐modulus wood filler. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1706–1711, 2006     

Tensile properties and damage behaviors of glass‐bead‐filled modified polyphenylene oxide under large strain

Based on Continuum Damage Mechanics (CDM), a damage model for glass‐bead‐filled modified polyphenylene oxide (GB/PPO) has been proposed to describe its damage behavior at various levels of tensile strain by considering the reduction of effective loading area. Hence, an equation for prediction of effective elastic modulus of the damaged GB/PPO composites in terms of the three principal true strains was derived. The tensile properties and damage behaviors of the GB/PPO composites with different volume percentages of glass beads were investigated using standard tensile tests and load‐unload tests, respectively. The addition of glass beads increases Young's modulus of PPO but has a weakening effect on its tensile strength. A maximum value of tensile work to break and tensile strain at break was found when 5 vol% of glass beads with a mean diameter of 11 μm was blended with PPO. These results were justified through microscopic examination of the fracture surfaces of the tensile specimens by using a scanning electron microscope (SEM). In‐situ observations of the strain damage processes were made through the SEM equipped with a tensile stage to determine the strain at fully debonding of glass beads. The volumetric strain of GB/PPO composites increases because of microcavitation during strain damage. In general, the prediction for the effective elastic modulus of the damaged GB/PPO composites at different true strains is slightly higher than the experimental results. The damage evolution rates after fully debonding of glass beads from the matrix are close to those predicted by the proposed damage model.     

Thermosetting polyurethane‐multiwalled carbon nanotube composites: Thermomechanical properties and nanoindentation

In this study, composites based on a thermoset polyurethane elastomer (PU) and multiwalled carbon nanotubes (MWCNT) in the case of a PU of high elastic modulus (>200 MPa) are analyzed for the first time. As‐grown and modified nanotubes with 4 wt % of oxygenated functions (MWCNT‐ox) were employed to compare their effect on composite properties and maxima mechanical properties (elastic modulus and tensile strength) were reached at 0.5 wt % of MWCNT‐ox. Furthermore, by examining the morphology using optical and electron microscopies better dispersion and interaction of the nanotube‐matrix was observed for this material. DMTA data supports the observation of an increase in the glass transition temperature of ～20°C in the nanocomposites compared with the thermoset PU, which is an important result because it shows extended reliability in extreme environments. Finally, nanoindentation tests allowed a comparison with the conventional mechanical tests by measuring the elastic modulus and hardness at the subsurface of PU and the nanocomposites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41207.     

Resonance tracking atomic force acoustic microscopy quantitative modulus mapping of carbon nanotubes‐reinforced acrylonitrile–butadiene–styrene polymer

This work presents a resonance tracking atomic force acoustic microscopy (RT‐AFAM) quantitative modulus mapping of carbon nanotubes‐reinforced acrylonitrile–butadiene–styrene polymer. RT‐AFAM average local modulus values registered were in good agreement with those measured by nanoindentation test. RT‐AFAM mapping modulus, nanoindentation, and transmission electron microscopy imaging showed that carbon nanotubes reinforcement of acrylonitrile–butadiene–styrene polymer matrix gives an elastic modulus enhancement of approximately 18.3% compared with the polymer matrix alone and showed that this technique provides high spatial resolution and helps to characterize the elastic properties of reinforced thermoplastic polymers and new compound materials at nanoscale. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40628.     

Quantifying the mechanical properties of polymeric tubing and scaffold using atomic force microscopy and nanoindentation

Measurement of mechanical parameters of polymeric scaffolds presents a significant challenge due to their intricate shape and small characteristics dimensions of their elements—around 100 μm. In this study, mechanical properties of polymeric tubing and scaffold, made of biodegradable poly(l ‐lactic) acid (PLLA), were characterized using atomic force microscopy (AFM) and nanoindentation, complemented with tensile testing. AFM was employed to assess the properties of the tube and scaffold locally, while nanoindentation produced results with a dependency on the depth of indentation. As a result, the AFM‐measured elastic modulus differs from the nanoindentation data due to a substantial difference in indentation depth between the two methods. With AFM, a modulus between 2 and 2.5 GPa was measured, while a wide range was obtained from nanoindentation on both the tube and scaffold, depending on the indentation scale. Changes in the elastic modulus with in‐vitro degradation and aging were observed over the 1‐year period. To complement the indentation measurements, tensile testing was used to study the structural behavior of the tube, demonstrating the yielding, hardening and fracture properties of the material. POLYM. ENG. SCI., 59:1084–1091, 2019. © 2019 Society of Plastics Engineers     

Quasi‐static and dynamic nanoindentation of particle‐reinforced soft composites

The mechanical properties of ferromagnetic particle‐reinforced silicone–rubber matrix composites are examined with quasi‐static and dynamic nanoindentation measurements using Berkovich and flat punch indenters, respectively. Quasi‐static nanoindentation is performed to examine primary factors such as the loading and holding time, particle volume fraction, and indentation depth for these particle‐reinforced soft composites (PRSCs). The Einstein–Guth–Smallwood equation based on macroscopically mechanical property testing is utilized to describe the relationship between elastic modulus and particle content of PRSCs in quasi‐static tests. A good agreement between the nanoindentation and simulation prediction is obtained. To characterize the storage modulus and loss factors of PRSCs, the dynamic nanoindentation is then conducted over the force frequency range of 0–45 Hz to show that the dynamic properties are dominated by the particle content and the force frequency, and independent of indentation depth and oscillation amplitude. It is indicated that the nanoindentation is a versatile methodology to assess mechanical properties of microsized particulate soft composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44559.     

Preparation and characterization of wood‐(nylon 12) composites

The melting temperature of nylon 12 is lower than the degradation temperature of wood, which makes the preparation of wood‐(nylon 12) composites through a regular compounding/compression molding process possible. Results indicated that wood‐(nylon 12) composites had higher modulus of rupture, higher modulus of elasticity, and higher tensile strength than nylon 12, wood‐polypropylene (PP) composites, and wood‐high density polyethylene (HDPE) composites, respectively. Wood‐(nylon 12) composites also had higher thermal stability than wood‐PP composites and wood‐HDPE composites. Acting as a nucleating agent, wood increased the crystallization temperature and the degree of crystallinity of nylon 12 in wood‐(nylon 12) composites. The superior mechanical properties of wood‐(nylon 12) composites were ascribed to the good interfacial adhesion between wood and nylon 12 and the increased transcrystallinity of nylon 12 by wood. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103:270–276, 2007     

Epoxy composites based on amino‐silylated MMT: The role of interfaces and clay morphology

Epoxy‐based composites containing sodium montmorillonite (MMT) modified by silylation reaction with 3‐aminopropyltriethoxysilane (A1100) and N‐(2‐aminoethyl)‐3‐aminopropyltrimethoxysilane (A1120) were prepared. The effect of MMT chemical functionalization, as well as inorganic content and dispersion method (i.e., sonication or combination of sonication and ball‐milling) on the morphology and mechanical and thermal properties of composites was thoroughly investigated by X‐ray diffraction analysis, dynamic mechanical and tensile static analysis, nanoindentation measurements and cone calorimeter tests. Morphological characterization showed that the MMT particles are only slightly intercalated by epoxy molecules. Tensile stress, elongation at failure, and toughness of the epoxy composites based on silylated MMT were found to be improved. The presence of 1 and 3% wt/wt of A1100 and A1120 silylated MMT clays allowed the tensile elastic modulus to increase respectively, of about 10 and 15% with respect to the pristine epoxy matrix. The overall results showed that (1) the silylation of MMT clays is a valuable method to improve the interfacial interaction between filler and epoxy matrix and (2) the interfacial interaction plays a role more significant than the clay morphology (i.e., the extent of clay intercalation/exfoliation) over the composite properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of natural fibers on thermal and mechanical properties of natural fiber polypropylene composites studied by dynamic mechanical analysis

The present study deals with the effects of natural fibers on thermal and mechanical properties of natural fiber polypropylene composites using dynamic mechanical analysis. Composites of polypropylene and various natural fibers including kenaf fibers, wood flour, rice hulls, and newsprint fibers were prepared at 25 and 50% (by weight) fiber content levels. One and two percent maleic anhydride grafted polypropylene was also used as the compatibilizer for composites containing 25 and 50% fibers, respectively. Specimens for dynamic mechanical analysis tests were cut out of injection‐molded samples and were tested over a temperature range of ?60 to +120°C. Frequency of the oscillations was fixed at 1 Hz and the strain amplitude was 0.1%, which was well within the linear viscoelastic region. The heating rate was 2°C/min for all temperature scan tests. Storage modulus (E′), loss modulus (E″), and mechanical loss factor (tan δ) were collected during the test and were plotted versus temperature. An increase in storage and loss moduli and a decrease in the mechanical loss factor were observed for all composites indicating more elastic behavior of the composites as compared with the pure PP. Changes in phase transition temperatures were monitored and possible causes were discussed. Results indicated that glass transition was slightly shifted to lower temperatures in composites. α transition temperature was higher in the case of composites and its intensity was higher as well. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4341–4349, 2006     

Flexural modulus of SiC/SiC composites sintered by microwave and conventional heating

To deeply study the variation mechanisms of mechanical properties, flexural modulus of SiC fibers reinforced SiC matrix (SiC/SiC) composites prepared by conventional and microwave heating at 800?°C–1100?°C was discussed in detail. The elastic modulus of fibers and matrix, interface bonding strength and porosity of SiC/SiC composites were considered together to analyze the changing tendencies and differences in their flexural modulus. The elastic modulus of fiber and matrix was determined by nanoindentation technique and interface characteristics applying fiber push-out test. The porosity and microstructure examinations were characterized by mercury intrusion method, X-ray Diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscope (TEM). Moreover, two conflicts between the changing trends of elastic modulus and chemical compositions of composite components were focused and explained. Results indicate that three factors played different roles in the flexural modulus of SiC/SiC composites and residual tensile stress in composite components led to the conflicts between their elastic modulus and chemical compositions.     

Measuring the Surface and Bulk Modulus of Polished Polymers with AFM and Nanoindentation

Abstract

A new method to determine the elastic modulus of a material using the atomic force microscope (AFM) was proposed by Tang et al. [Nanotechnology 19, 495713 (2008)] and is used in this study. This method models the cantilever and the sample as two springs in a series. The properties of both the spring and cantilever are determined on two reference samples with known mechanical properties and these properties are then used to find the elastic modulus of an unknown sample. The indentation depth achieved with AFM is in the nanometer range (30–130 nm in this study); and hence when this technique is performed on polymers, whose surface structure is different from their bulk structure, AFM gives a measure of the surface elastic modulus. In the present study, after employing AFM to measure the surface modulus of five polymers, traditional depth-sensing nanoindentation, with penetration depths of about 1 μm, was used to determine the elastic modulus in the bulk. The mean values for elastic modulus from the AFM were within 5–50% of the nanoindentation results, suggesting the existence of a surface modulus for polished polymers.     

Mechanical properties of natural carbon black reinforced polymer composites

This article describes the development of new carbon black material from agricultural waste (wood apple shells) by using pyrolysis method at various carbonization temperatures (400, 600, and 800°C) and used as reinforcement in polymer composites. The wood apple shell carbon black (WAS‐CB) particulates are characterized by proximate analysis, energy dispersive spectroscopy (EDS), and scanning electron microscope (SEM). Results showed that due to increases in carbonization temperature the percentage of carbon improved in the carbon black particles. Furthermore, various tests were performed to determine the effect of new carbon black material on the mechanical properties of composite at different filler loading. The results indicated that mechanical properties like tensile strength, tensile modulus, flexural strength, and flexural modulus are improved as the increase in the carbonization temperature and filler loading. The filler‐matrix bonding was analyzed by SEM. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41211.     

Random glass mat reinforced thermoplastic composites. Part I: Phenomenology of tensile modulus variations

The mechanical properties of random continuous glass mat reinforced composites, as determined by standard tensile tests, are known to have a very large scatter. To understand this scatter, new test procedures were developed to map the local tensile elastic moduli in a large plaque at 12.7-mm (½-in) intervals. Surprisingly, the tensile modulus in these materials can vary by a factor of two over the 12.7-mm distance. The elastic modulus is shown to vary by a factor of three in a 150 × 305-mm (6 × 12 in) plaque. Expressions have been obtained for the average moduli measured by tensile and bend tests. These expressions have been used to compare measured flexural moduli with values predicted by using measured tensile moduli.     

Understanding the viscoelastic properties of extruded polypropylene wood plastic composites

The main goal of this study was to analyze the effect of process additives, that is, maleated polypropylene (MAPP), and a nucleating agent on the viscoelastic properties of different types of extruded polypropylene (PP) wood plastic composites manufactured from either a PP homopolymer, a high crystallinity PP, or a PP impact copolymer using dynamic mechanical thermal analysis. The wood plastic composites were manufactured using 60% pine wood flour and 40% PP on a Davis‐Standard Woodtruder?. Dynamic mechanical thermal properties, polymer damping peaks (tan δ), storage modulus (E′), and loss modulus (E″) were measured using a dynamic mechanical thermal analyzer. To analyze the effect of the frequency on the dynamic mechanical properties of the various composites, DMA tests were performed over a temperature range of ?20 to 100°C, at four different frequencies (1, 5, 10, and 25 Hz) and at a heating rate of 5°C/min. From these results, the activation energy of the various composites was measured using an Arrhenius relationship to investigate the effect of MAPP and the nucleating agent on the measurement of the interphase between the wood and plastic of the extruded PP wood plastic composites. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1638–1644, 2003     

Moisture absorption effects on the thermal and mechanical properties of wood flour/linseed oil resin composites

The thermal and mechanical behavior of new natural polymeric composite materials after exposure to humid environments must be well known and understood in order to predict their performance in final applications. For this reason, composites made from unsaturated polyesters based on linseed oil and filled with wood flour were exposed to environments of different relative humidities and their final properties were measured. In general, the equilibrium moisture content increased as the wood flour percentage increased. Dynamic mechanical tests performed in temperature scan mode were carried out in order to monitor the changes resulting from moisture absorption on the main transition temperature of the matrix (T_α). The temperature of this transition decreased as the amount of absorbed water increased, but the effect was partially reversible by re‐drying the samples. The mechanical properties were also strongly affected by moisture. The flexural modulus and ultimate stress of the composites decreased after equilibration in humid environments. Copyright © 2006 Society of Chemical Industry     

Tensile properties of wood flour/kenaf fiber polypropylene hybrid composites

Hybrid composites of wood flour/kenaf fiber and polypropylene were prepared at a fixed fiber to plastic ratio of 40 : 60 and variable ratios of the two reinforcements namely 40 : 0, 30 : 10, 20 : 20, 10 : 30, and 0 : 40 by weight. Polypropylene was used as the polymer matrix, and 40–80 mesh kenaf fiber and 60–100 mesh wood flour were used as the fiber and the particulate reinforcement, respectively. Maleic anhydride and dicumyl peroxide were also used as the coupling agent and initiator, respectively. Mixing process was carried out in an internal mixer at 180°C at 60 rpm. ASTM D 638 Type I tensile specimens of the composites were produced by injection molding. Static tensile tests were performed to study the mechanical behavior of the hybrid composites. The hybrid effect on the elastic modulus of the composites was also investigated using the rule of hybrid mixtures and Halpin–Tsai equations. The relationship between experimental and predicted values was evaluated and accuracy estimation of the models was performed. The results indicated that while nonhybrid composites of kenaf fiber and wood flour exhibited the highest and lowest modulus values respectively, the moduli of hybrid composites were closely related to the fiber to particle ratio of the reinforcements. Rule of hybrid mixtures equation was able to predict the elastic modulus of the composites better than Halpin–Tsai equation. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Kenaf‐filled biodegradable composites: rheological and mechanical behaviour

Biodegradable polymer composites, typically based on biodegradable polymer matrices and natural‐organic fillers, are gaining rising interest and importance over the last few years. Several natural‐organic fillers can be used but the most widespread so far is wood, in the form of fibres or flour. Alternative cellulosic fillers can ensure advantages in terms of resource utilization and properties of the final composite. In this work, Mater‐Bi^® based biodegradable composites were prepared with two kinds of wood flour, and directly compared with alternative composites containing kenaf fibres. The use of kenaf fibres allowed improved elastic modulus, tensile strength and interaction with the polymer matrix to be obtained, although the filler dispersion was worse. Rheological measurements evidenced higher viscosity and an increasingly elastic behaviour of the melt. Copyright © 2012 Society of Chemical Industry     

Nanoscale mechanical properties of polymers irradiated by UV

The application of depth sensing nanoindentation to determine mechanical properties of three different polymers is described in this work using three different techniques to calibrate the measurement system. The nano-hardness and the elastic indentation modulus of polyvinyl chloride, polyethylene oxide and polyacrylic acid were inferred from nanomechanical tests, and the influence of ultraviolet irradiation on the mechanical properties of measured polymers is studied. A multicycling test—a sequence of several loading and unloading procedures—allowed the measurement of changes in the sample viscoelasticity. The nano-hardness of the polymers is shown to increase with radiation dose while the viscoelasticity decreases.