Electrochemical behaviour of uranium (IV) in DMF at vitreous carbon

The electrochemical behaviour of UCl₄ (0.01 mol L⁻¹ up to 0.05 mol L⁻¹) in 0.1 mol L⁻¹ TBAPF₆/DMF solution at vitreous carbon was studied, at room temperature, by cyclic voltammetry and potentiostatic techniques. The electrolytic solutions were analyzed by UV spectroscopy (UV), and the electrodeposited films were characterized by Rutherford Backscattering Spectroscopy (RBS) and X-ray diffraction (XRD). The cyclic voltammetric results, at low UCl₄ concentrations (0.01 mol L⁻¹), point that the reduction of U(IV) to U(0) occurs in two steps involving mainly U(IV) and U(III) species. The first electron transfer reaction is quasi-reversible and the second irreversible. The diffusion coefficient of U(IV) in DMF and the charge rate constant were determined to be 4.78 × 10⁻⁷ cm² s⁻¹ and 1.93 × 10⁻³ cm s⁻¹ (at 0.02 V s⁻¹), respectively.RBS data obtained from samples prepared at constant potential (−3.10 V) during 3 h at room temperature, indicated the presence of uranium particles deposited all over the vitreous carbon surface with aggregates in some places, confirming that the second reduction step corresponds to uranium electrodeposition. No crystallographic ordering could be seen by XRD, pointing to an amorphous character of the uranium films.     

Electrochemical promotion of toluene combustion on an inexpensive metallic catalyst

Electrochemical promotion of the complete catalytic oxidation of toluene at 310 °C is reported, using a Ag/YSZ/Ag two electrode system where Ag films were deposited on YSZ from AgNO₃ aqueous solution followed by reduction in H₂. After on-stream activation, a non-negligible conversion (about 30%) at OCV is reached and then the rate of the catalytic toluene conversion into CO₂ and H₂O can be multiplied by a factor higher than 1.5, by application of a small negative current (about—4 μA cm⁻²). The associated Faradaic efficiency is very high and may exceed −13,000.     

Diamond-like carbon thin films by microwave surface-wave plasma CVD aimed for the application of photovoltaic solar cells

The nitrogen doped diamond-like carbon (DLC) thin films were deposited on quartz and silicon substrates by a newly developed microwave surface-wave plasma chemical vapor deposition, aiming the application of the films for photovoltaic solar cells. For film deposition, we used argon as carrier gas, nitrogen as dopant and hydrocarbon source gases, such as camphor (C₁₀H₁₆O) dissolved with ethyl alcohol (C₂H₅OH), methane (CH₄), ethylene (C₂H₄) and acetylene (C₂H₂). The optical and electrical properties of the films were studied using X-ray photoelectron spectroscopy, Nanopics 2100/NPX200 surface profiler, UV/VIS/NIR spectroscopy, atomic force microscope, electrical conductivity and solar simulator measurements. The optical band gap of the films has been lowered from 3.1 to 2.4 eV by nitrogen doping, and from 2.65 to 1.9 eV by experimenting with different hydrocarbon source gases. The nitrogen doped (flow rate: 5 sccm; atomic fraction: 5.16%) film shows semiconducting properties in dark (i.e. 8.1 × 10^{− 4} Ω^{− 1} cm^{− 1}) and under the light illumination (i.e. 9.9 × 10^{− 4} Ω^{− 1} cm^{− 1}). The surface morphology of the both undoped and nitrogen doped films are found to be very smooth (RMS roughness ≤ 0.5 nm). The preliminary investigation on photovoltaic properties of DLC (nitrogen doped)/p-Si structure show that open-circuit voltage of 223 mV and short-circuit current density of 8.3 × 10^{− 3} mA/cm². The power conversion efficiency and fill factor of this structure were found to be 3.6 × 10^{− 4}% and 17.9%, respectively. The use of DLC in photovoltaic solar cells is still in its infancy due to the complicated microstructure of carbon bondings, high defect density, low photoconductivity and difficulties in controlling conduction type. Our research work is in progress to realize cheap, reasonably high efficiency and environmental friendly DLC-based photovoltaic solar cells in the future.     

The role of pressure on thin amorphous carbon films deposited using microwave surface wave plasma CVD

We report the effects of gas composition pressure (GCP) on the optical, structural and electrical properties of thin amorphous carbon (a-C) films grown on p-type silicon and quartz substrates by microwave surface wave plasma chemical vapor deposition (MW SWP CVD). The films, deposited at various GCPs ranging from 50 to 110 Pa, were studied by UV/VIS/NIR spectroscopy, atomic force microscopy, Raman spectroscopy, X-ray photoelectron spectroscopy and current–voltage characteristics. The optical band gap of the a-C film was tailored to a relatively high range, 2.3–2.6 eV by manipulating GCPs from 50 to 110 Pa. Also, spin density strongly depended on the band gap of the a-C films. Raman spectra showed qualitative structured changes due to sp³/sp² carbon bonding network. The surfaces of the films are found to be very smooth and uniform (RMS roughness < 0.5 nm). The photovoltaic measurements under light illumination (AM 1.5, 100 mW/cm²) show that short-circuit current density, open-circuit voltage, fill factor and photo-conversion efficiency of the film deposited at 50 Pa were 6.4 μA/cm², 126 mV, 0.164 and 1.4 × 10^− 4% respectively.     

Multi-walled carbon nanotubes (MWCNTs) and room temperature ionic liquids (RTILs) carbon paste Er(III) sensor based on a new derivative of dansyl chloride

Solution studies showed the strong interaction of [5-(dimethylamino) naphthalene-1-sulfonyl 4-phenylsemicarbazide] (NSP) with Er(III) ions. NSP was used as a sensing material during construction of carbon paste Er(III) sensors. The electrodes were modified with 1-n-butyl-3-methylimidazolium tetrafluoroborate, [bmim]BF₄, as room temperature ionic liquid (RTIL) and multi-walled carbon nanotube (MWCNT). Potentiometric sensors constructed with [bmim]BF₄ and MWCNTs show better sensitivity, selectivity, response time, and response stability compared to Er(III) carbon paste sensors. The best performance for the modified sensor was obtained with an electrode composition of 20% [bmim]BF₄, 20% NSP, 45% graphite powder and 15% MWCNT. This particular sensor formulation exhibits a Nernstian response (19.8 ± 0.3 mV decade⁻¹) toward Er(III) ions in the range of 1.0 × 10⁻⁷ to 1.0 × 10⁻¹ mol L⁻¹ with a detection limit of 5.0 × 10⁻⁸ mol L⁻¹. The proposed modified Er(III) sensor can be used over the pH range from 3.5 to 9.0.     

Amorphous carbon nanofibres inducing high specific capacitance of deposited hydrous ruthenium oxide

Composites consisting of ruthenium oxide particles deposited on amorphous carbon nanofibres are prepared by a repetitive impregnation procedure. The choice of amorphous carbon nanofibres as support of amorphous ruthenium oxide leads to composites in which the deposited oxide consists of aggregates of extremely small primary particles (1–1.5 nm-size) and showing high porosity (specific surface area of 450 m² g⁻¹). This special deposition of the oxide seems to favour: (i) high oxide capacitance (1000 Fg⁻¹) at high oxide loadings (up to 20 wt%) and (ii) high capacitance retention (ca. 80% from the initial oxide capacitance) at high current densities (200 mA cm⁻²). Amorphous carbon nanofibres are suitable supports for amorphous ruthenium oxide and perhaps for other amorphous oxides acting as active electrode materials.     

An effect of iron(III) oxides crystallinity on their catalytic efficiency and applicability in phenol degradation—A competition between homogeneous and heterogeneous catalysis

Catalytic efficiency, stability and environmental applicability of five iron(III) oxide nanopowders differing in surface area and crystallinity were tested in degradation of concentrated phenolic aqueous solutions (100 g/L) at mild temperature (30 °C), initially almost neutral pH and equimolar ratio of hydrogen peroxide and phenol. The catalyst properties were easily controlled by varying in reaction time during isothermal treatment of ferrous oxalate dihydrate in air at 175 °C. Although the catalytic efficiency clearly increases with the surface area of the nanopowders, it is not due to the solely heterogeneous catalytic mechanism as would be expected. The amorphous Fe₂O₃ nanopowders possessing the largest surface areas (401 m² g⁻¹, 386 m² g⁻¹) are the most efficient catalysts evidently due to their highest susceptibility to leaching in acidic environment arising as a consequence of phenol degradation products. Thus, these amorphous samples act partially as homogeneous catalysts, which was confirmed by a high concentration of leached Fe(III) ions in the solution (19 ppm). The crystalline hematite (α-Fe₂O₃) samples, varying in surface area between 337 m² g⁻¹ and 245 m² g⁻¹, are generally less efficient when compared to the amorphous powders, however their catalytic action is almost exclusively heterogeneous as only 3 ppm of leached Fe(III) was found in the reaction systems catalyzed by nanohematite samples. A significant difference in relative contributions of heterogeneous and homogenous catalysis was definitely established in buffered reaction systems catalyzed by amorphous Fe₂O₃ and nanocrystalline hematite. The nanohematite sample exhibiting the highest heterogeneous action was tested at decreased initial phenol concentration (10 g/L), which is closer to the real contents of phenol in waste waters, and at different hydrogen peroxide/phenol molar ratios to consider its environmental applicability. At the hydrogen peroxide/phenol ratio equal to 5, no traces of the leached iron were detected and the phenol conversion of 84% was reached. Moreover, such a high degree of conversion is accompanied by a decrease of the chemical oxygen demand (COD) from the initial value of 11.23 g/L to 4.22 g/L after 125 min. This fact indicates that the considerable fraction of primary reaction products was totally degraded.     

Immobilization of horseradish peroxidase on self-assembled (3-mercaptopropyl)trimethoxysilane film: Characterization, direct electrochemistry, redox thermodynamics and biosensing

Highly organized (3-mercaptopropyl)trimethoxysilane (3-MPT) films have been prepared via self-assembled coupled with sol–gel linking technology. Horseradish peroxidase (HRP) is successfully immobilized onto the densely packed three-dimensional (3D) 3-MPT network and the direct electrochemistry of HRP is achieved without any electron mediators or promoters. Redox thermodynamics of HRP on the 3-MPT films, which is obtained from the temperature dependence of the reduction potential, suggests that the positive shift of redox potentials of HRP at the interface of 3-MPT originates from the solvent reorganization effects and conformational change of the polypeptide chain of HRP. Based on the direct electrochemistry and electrocatalytic ability of HRP, a sensitive third-generation amperometric H₂O₂ biosensor is developed with two linear dependence ranges of 5.0 × 10⁻⁷ to 1.0 × 10⁻⁴ and 1.0 × 10⁻⁴ to 2.0 × 10⁻² mol L⁻¹.     

Hydrogen effects on pitting corrosion and semiconducting properties of nitrogen-containing type 316L stainless steel

The effects of hydrogen pre-charging on pitting corrosion resistance and semiconducting nature of passive film formed on two different nitrogen-containing type 316L stainless steel (0.076 and 0.086 wt% N) have been studied. Auger electron spectroscopy (AES) analysis of the alloys after passivation indicated weak nitrogen peak, but the presence of nitrogen and NH₃/NH₄⁺ was confirmed by the X-ray photoelectron spectroscopy (XPS) analysis. The results of pitting corrosion in 0.5 M NaCl (pH ≈ 5.7) solution revealed that hydrogen increased the passive current density and significantly reduced the pitting resistance. In 0.3 M H₃BO₃ + 0.075 M Na₂B₄O₇·10H₂O (pH ≈ 8.45) solution, increase in passive current density without affecting the breakdown or transpassive potential was observed for both the alloys. Electrochemical impedance spectroscopy (EIS) measurement after hydrogen pre-charging showed decrease in semi-circle radius of Nyquist plot, and the polarization resistance, R_P associated with the resistance of the passive film. The decrease was significant with increasing hydrogen-charging current density (−50 to −100 mA/cm²). The results of the capacitance measurement and Mott–Schottky plots revealed that passive films exhibit n-type and p-type semiconductivity films for both the uncharged and hydrogen charged specimens of the investigated alloys. Doping densities obtained from Mott–Schottky plots increased with hydrogen pre-charging. The overall results indicated that hydrogen pre-charging deteriorated the passive film stability and lowered pitting corrosion resistance. The effects of hydrogen pre-charging on pitting corrosion, passive film and semiconducting properties are discussed in light of the above results.     

Solubilities of actinides in a domestic groundwater and a bentonite porewater calculated by using PHREEQC

This study presents the solubilities and speciations of actinides, calculated by the PHREEQC (V.2) code in a granitic groundwater and a Ca-bentonite porewater under a reducing condition. The respective solubilities for the amorphous U, Am, Th, Np and Pu compounds in the groundwater were 2.2 × 10⁻⁵, 1.2 × 10⁻⁷, 3.1 × 10⁻⁹, 3.4 × 10⁻⁹ and 6.3 × 10⁻¹¹ mole/L, and these values are comparable to the results calculated by the MUGREM and EQ3/6 codes. The major dissolved species for U, Am, Th, Np and Pu were UO₂(OH)₃⁻, Am(OH)₂⁺, Th(OH)₄(aq), Np(OH)₃CO₃⁻ and Pu(OH)₃CO₃⁻, respectively. However, carbonate complex ions were anticipated as the major species in the porewater except for thorium due to an increase of the carbonate concentration and a decrease of the pH.     

Ferromagnetic coupling in a novel dicyanamide-bridged dinuclear gadolinium(III) complex [Gd2(dca)4(OH)2 (NITpPy)4] (NITpPy = 4-pyridyl-nitronyl nitroxide radical)

The novel six-coordinated gadolinium(III) complex of formula [Gd₂(dca)₄(OH)₂(NITpPy)₄] (1) (dca = dicyanamide, NITpPy = 4-pyridyl-4,4,5,5-tetramethyl-4,5-dihydro-1H-imidazolyl-oxy-3-oxide) has been prepared and characterized by X-ray crystallography. Compound 1 is a dimer structure made up of double μ_1,5-dca-bridged gadolinium(III) ions and one terminal dca ligand; variable-temperature magnetic susceptibility measurements reveal the occurrence of a significant ferromagnetic interaction directly spin polarization through the NITpPy–Gd(III)–NITpPy pathway with J = 11.56 cm⁻¹.     

Direct oxidation of sodium borohydride on Pt, Ag and alloyed Pt–Ag electrodes in basic media. Part I: Bulk electrodes

We studied the borohydride oxidation reaction (BOR) by voltammetry for BH₄⁻ concentrations between 10⁻³ M and 0.1 M NaBH₄ in 0.1–1 M NaOH for bulk polycrystalline Pt, Ag and alloyed Pt–Ag electrocatalysts. In order to compare the different electrocatalysts, we measured the kinetic parameters and the number of electrons exchanged (faradic efficiency). BOR on bulk Pt is more efficient when the concentration of NaBH₄ increases (3e⁻ in 1 mM and 6e⁻ in 10 mM BH₄⁻/0.1 M NaOH). BOR on Pt can occur both in a direct pathway and in an indirect pathway including hydrogen generation via heterogeneous hydrolysis of BH₄⁻ and subsequent oxidation of its by-products (e.g. BH₃OH⁻ and H₂). BOR on Ag strongly depends on the pH: improved faradic efficiency is monitored for high pH (2e⁻ at pH 12.6 and 6e⁻ at pH 13.9 at 25 °C). The BOR kinetics is faster for Pt than for Ag (i_Pt=0.02 A cm⁻², i_Ag=1.4 10⁻⁷ A cm⁻² at E=−0.65 V vs. NHE in 1 mM NaBH₄/0.1 M NaOH, 25 °C) both as a result from Pt high activity regarding the BH₄⁻ heterogeneous hydrolysis and subsequent HOR, above −0.83 V vs. NHE and following direct oxidation of BH₄⁻ or BH₃OH⁻ below −0.83 V vs. NHE. Both Pt–Ag bulk alloys show unique behaviour: the number of electrons exchanged is rather high whatever the BH₄⁻ concentration and pH, while the kinetic parameters are quite similar to that of platinum, showing possible synergistic alloying effect.     

Tribological properties of DLC films with different hydrogen contents in water environment

Diamond-like carbon (DLC) films were deposited on silicon wafers by thermal electron excited chemical vapor deposition (CVD). To change the hydrogen content in film, we used three types of carbon source gas (C₇H₈, CH₄, and a CH₄+H₂) and two substrate bias voltages. The hydrogen content in DLC films was analyzed using elastic recoil detection analysis (ERDA). Tribological tests were conducted using a ball-on-plate reciprocating friction tester. The friction surface morphology of DLC films and mating balls was observed using optical microscopy and laser Raman spectroscopy.Hydrogen content in DLC films ranged from 25 to 45 at.%. In a water environment, the friction coefficient and specific wear rate of DLC films were 0.07 and in the range of 10⁻⁸–10⁻⁹ mm³/Nm, respectively. The friction coefficient and specific wear rate of DLC film in water were hardly affected by hydrogen content. The specific wear rate of DLC film with higher hardness was lower than that of film with low hardness. Mating ball wear was negligible and the friction surface features on the mating ball differed clearly between water and air environments, i.e., the friction surface on mating balls in water was covered with more transferred material than that in air.     

Influence of ZnO buffer layer on AZO film properties by radio frequency magnetron sputtering

Transparent conductive films of Al-doped zinc oxide (AZO) were deposited on glass substrates under various ZnO buffer layer deposition conditions (radio frequency (r.f.) power, sputtering pressure, thickness, and annealing) using r.f. magnetron sputtering at room temperature. This work investigates the influence of ZnO buffer layer on structural, electrical, and optical properties of AZO films. The use of grey-based Taguchi method to determine the ZnO buffer layer deposition processing parameters by considering multiple performance characteristics has been reported. Findings show that the ZnO buffer layer improves the optoelectronic performances of AZO films. The AZO films deposited on the 150-nm thick ZnO buffer layer exhibit a very smooth surface with excellent optical properties. Highly c-axis-orientated AZO/ZnO/glass films were grown. Under the optimized ZnO buffer layer deposition conditions, the AZO films show lowest electrical resistivity of 6.75 × 10⁻⁴ Ω cm, about 85% optical transmittance in the visible region, and the best surface roughness of R_a = 0.933 nm.     

Nanostructured α- and β-cobalt hydroxide thin films

A new perspective in the use of electrochemical methods to deposit cobalt hydroxide thin films is presented. Ordered arrays of α-Co(OH)₂ (hydrotalcite-like (Co-HT)) and β-Co(OH)₂ nanoparticles were synthesized on transparent conductive oxide (TCO) substrates by localized cathodic electrogeneration of hydroxyl via the reduction of NO₂⁻ (or NO₃⁻) ion precursors in solution containing Co²⁺ in very low concentration. The thin films, analyzed by X-ray diffraction and scanning electron microscopy were found to be composed of vertically oriented platelets with the crystallographic c-axis parallel to the substrate surface. Turbostratic disorder was not observed in the films. UV/Vis spectra and thermal gravimetric analyses (TGA) indicated distinct variation between the Co-HT structures. Films deposited at 60 °C using a nitrite precursor generated uniform, vibrant-green mixed-valence Co-HT (Co²⁺/Co³⁺). Nitrate precursors yielded a “hydroxyl-deficient” Co-HT (Co²⁺ only). Films deposited at 95 °C in nitrate solution yielded β-Co(OH)₂. The films obtained in presence of nitrite were thicker than those obtained in nitrate. They were formed of β-Co(OH)₂ and contained traces of Co-HT.     

Magnetic properties of CNX whiskers

Carbon–nitrogen whiskers have been prepared by pyrolysis of 1,2-diaminopropane at 950 °C or of allylamine at 900 °C followed by quenching. They are scrolls of carbon film typically 250 nm thick and up to 1 mm long with about five layers in a structure like a “cigare russe” or “brandy snap”, about 50 μm in diameter. Approximately 8 wt% of nitrogen is incorporated into the carbon films, which are practically amorphous, exhibiting a broad diffraction peak at d = 0.34 nm. The whiskers are on the border of metallic conductivity with a resistivity of about 10⁻⁶ Ωm, and they may show either a positive or a negative temperature coefficient of resistance. The pyrolysis produces either whiskers, soot or both. Magnetization measurements of the whiskers made from 1,2-diaminopropane reveal a large diamagnetic susceptibility of χ = −170 × 10⁻⁹ m³  kg⁻¹ and a small ferromagnetic component of unknown origin with σ_S of up to 0.2 A m² kg⁻¹, whereas the soot shows a purely diamagnetic signal, with χ ≈ −40 × 10⁻⁹ m³ kg⁻¹.     

Electrochemical polymerisation of thiophene derivative induced by Lewis acid: Electrosynthesis of poly[(R)-(−)-2-(3′-thienyl)ethyl-(3′,5″-dinitrobenzoyl)-α-phenylglycinate]

Films of poly[(R)-(−)-2-(3′-thienyl)ethyl-(3′,5″-dinitrobenzoyl)-α-phenylglycinate] were deposited on ITO electrodes by potentiodynamic, potentiostatic and galvanostatic methods using a (C₄H₉)₄NBF₄/CH₃CN electrolyte system containing 20% boron trifluoride diethyl etherate. Polymerisation occurred as a charge dependent process at a potential of 1.4 V vs. Ag/Ag⁺(CH₃CN). The surface morphologies of the films so-formed were examined using atomic force microscopy. The film deposited by the galvanostatic method displayed more homogeneous grain geometry and a larger superficial area than those formed by the other methods. Cyclic voltammetry revealed a well defined redox couple at the anodic region, attributable to polymer p-doping, and a poorly defined redox pair at the cathodic region, attributable to the reduction of the nitro group. The polymeric films obtained were yellow in colour (λ_max 425 nm) in the reduced state and light blue (λ_max 745 nm) in the oxidised state.     

Polymeric semiconducting carbon from fullerene by pulsed laser ablation

The polymeric semiconducting carbon films are grown on silicon and quartz substrates by excimer (XeCl) pulsed laser deposition (PLD) technique using fullerene C₆₀ precursor. The substrate temperature is varied up to 300 °C. The structure and optical properties of the films strongly depend on the substrate temperature. The grain size is increased and uniform polymeric film with improved morphology at higher temperature is observed. The Tauc gap is about 1.35 eV for the film deposited at 100°C and with temperature the gap is decreased upto 1.1 eV for the film deposited at 250 °C and increased to about 1.4 eV for the film deposited at 300 °C. The optical absorption properties are improved with substrate temperature. Raman spectra show the presence of both G peak and D peak and are peaked at about 1590 cm^− 1 and 1360 cm^− 1, respectively for the film deposited at 100 °C. The G peak position remains almost unchanged while D peak has changed only a little with temperature might be due to its better crystalline structure compared to the typical amorphous carbon films and might show interesting in device such as, optoelectronic applications.     

Decomposition of ozone on Ag/SiO2 catalyst for abatement of waste gases emissions

A silica-supported Ag system made by the incipient wetness impregnation method was investigated in the reaction of heterogeneous catalytic decomposition of ozone. It was established that the catalytic ozone decomposition on Ag/SiO₂ proceeded in the temperature interval −40 °C to 25 °C as a first order reaction with activation energy of 65 kJ/mol (pre-exponential factor 5.0 × 10¹⁴ s⁻¹). Based on the results from the instrumental methods (SEM, XRD, XPS, EPR, TPD) it can be concluded that in presence of ozone the silver is oxidized to a complicated mixture of Ag₂O₃ and AgO. Due to the high activity and stability of the Ag/SiO₂ catalyst, it is promising for neutralization of waste gases containing ozone.     

Synthesis of nitrogen incorporated diamond-like carbon thin films using microwave surface-wave plasma CVD

Nitrogenated diamond-like (DLC:N) carbon thin films have been deposited by microwave surface wave plasma chemical vapor deposition on silicon and quartz substrates, using argon gas, camphor dissolved in ethyl alcohol composition and nitrogen as plasma source. The deposited DLC:N films were characterized for their chemical, optical, structural and electrical properties through X-ray photoelectron spectroscopy, UV/VIS/NIR spectroscopy, Raman spectroscopy, atomic force microscope and current–voltage characteristics. Optical band gap decreased (2.7 to 2.4 eV) with increasing Ar gas flow rate. The photovoltaic measurements of DLC:N / p-Si structure show that the open-circuit voltage (V_oc) of 168.8 mV and a short-circuit current density (J_sc) of 8.4 μA/cm² under light illumination (AM 1.5 100 mW/cm²). The energy conversion efficiency and fill factor were found to be 3.4 × 10^{− 4}% and 0.238 respectively.