Spectral characteristic of laser-induced plasma in soil

The spectral characteristic of laser-induced plasma in soil was studied in this work, laser-induced breakdown spectroscopy was used to analyze the spectral characteristic of plasma under the condition of different time delays and irradiances. Moreover, the time evolution characteristics of plasma temperature and electron density were discussed. Within the time delay range of 0-5 μs,the spectral intensity of the characteristic lines of Si I: 288.158 nm, Ti I: 336.126 nm, Al I:394.400 nm and Fe I: 438.354 nm of the four main elements in two kinds of national standard soil decayed exponentially with time. The average lifetime of the spectral lines was nearly 1.56 μs. Under the condition of different time delays, the spectral intensity of Pb I: 405.78 nm in soil increased linearly with laser energy. However, the slope between the spectral intensity and laser energy decreased exponentially with the increase in time delay, from 4.91 to 0.99 during 0-5 μs. The plasma temperature was calculated by the Boltzmann plot method and the electron density was obtained by inversion of the full width at half maximum of the spectrum. The plasma temperature decreased from 8900 K to 7800 K and the electron density decreased from 1.5 × 10~(17) cm~(-3) to 7.8 × 10~(16) cm~(-3) in the range of 0-5 μs.     

Laser-induced plasma generated by a 532nm pulsed laser in bulk water:unexpected line-intensity variation with water temperature and the possible underlying physics

The effect of the matrix temperature on laser-induced plasma generated in bulk water by using a532 nm pulsed laser beam has been studied.Ca Ⅰ and Ⅱ emission line intensities were recorded for an aqueous solution of CaCl_2 in the temperature range of 7℃-70℃.The emission line intensities did not follow the matrix temperature in our experiments.Maximum intensities were observed at ～18℃ for both lines.Herein,a possible mechanism responsible for the observed variation in intensity is suggested,in which laser-produced bubbles play important roles.Bubble formation is essential to ignite plasma in the liquid and more feasible at the higher liquid temperature.However,the abundant bubbles at the higher temperature can scatter the incident laser beam more effectively to decrease the energy delivered for the laser-induced plasma.Thus,these two roles have effects on the optical emission intensities in opposite ways.The validity of the suggested mechanism is discussed based on the plasma temperature,temperature dependence of the refractive index of water,plasma electron density,scattered light intensity,and plasma ignition threshold energy.Our result indicates that the temperature of the liquid is also an important parameter to be considered in the laser-induced breakdown spectroscopy analysis of bulk liquid samples and its application in deep-sea exploration.     

Effect of distances between lens and sample surface on laser-induced breakdown spectroscopy with spatial confinement

Spatial confinement can significantly enhance the spectral intensity of laser-induced plasma in air.It is attributed to the compression of plasma plume by the reflected shockwave.In addition,optical emission spectroscopy of laser-induced plasma can also be affected by the distance between lens and sample surface.In order to obtain the optimized spectral intensity,the distance must be considered.In this work,spatially confined laser-induced silicon plasma by using a Nd:YAG nanosecond laser at different distances between lens and sample surface was investigated.The laser energies were 12 mJ,16 mJ,20 mJ,and 24 mJ.All experiments were carried out in an atmospheric environment.The results indicated that the intensity of Si (I) 390.55 nm line firstly rose and then dropped with the increase of lens-to-sample distance.Moreover,the spectral peak intensity with spatial confinement was higher than that without spatial confinement.The enhancement ratio was approximately 2 when laser energy was 24 mJ.     

Diagnostics of laser-induced plasma on carbon-based polymer material using atomic and molecular emission spectra

Time-integrated optical emission analysis of laser-induced plasma on Teflon is presented.Plasma was induced under atmospheric pressure air using transversely excited atmospheric CO₂ laser pulses. Teflon is a C-based polymer that is, among other things, interesting as a substrate for laser-induced breakdown spectroscopy analysis of liquid samples. This study aimed to determine the optimal experimental conditions for obtaining neutral and ionized C spectral lines and C₂ and C...     

Self-absorption effects of laser-induced breakdown spectroscopy under different gases and gas pressures

The self-absorption effect is one of the main factors affecting the quantitative analysis accuracy of laser-induced breakdown spectroscopy. In this paper, the self-absorption effects of laserinduced 7050 Al alloy plasma under different pressures in air, Ar, and N₂ have been studied.Compared with air and N₂, Ar significantly enhances the spectral signal. Furthermore, the spectral self-absorption coefficient is calculated to quantify the degree of self-absorption, and the inf...     

Effect of lens focusing distance on laser-induced silicon plasmas at different sample temperatures

We investigated the dependence of laser-induced breakdown spectral intensity on the focusing position of a lens at different sample temperatures(room temperature to 300 ℃) in atmosphere.A Q-switched Nd:YAG nanosecond pulsed laser with 1064 nm wavelength and 10 ns pulse width was used to ablate silicon to produce plasma. It was confirmed that the increase in the sample's initial temperature could improve spectral line intensity. In addition, when the distance from the target surface to the focal point increased, the intensity firstly rose, and then dropped.The trend of change with distance was more obvious at higher sample temperatures. By observing the distribution of the normalized ratio of Si atomic spectral line intensity and Si ionic spectral line intensity as functions of distance and temperature, the maximum value of normalized ratio appeared at the longer distance as the initial temperature was higher, while the maximum ratio appeared at the shorter distance as the sample temperature was lower.     

Relative spectral response calibration using Ti plasma lines

This work introduces the branching ratio(BR) method for determining relative spectral responses,which are needed routinely in laser induced breakdown spectroscopy(LIBS). Neutral and singly ionized Ti lines in the 250–498 nm spectral range are investigated by measuring laser-induced micro plasma near a Ti plate and used to calculate the relative spectral response of an entire LIBS detection system. The results are compared with those of the conventional relative spectral response calibration method using a tungsten halogen lamp, and certain lines available for the BR method are selected. The study supports the common manner of using BRs to calibrate the detection system in LIBS setups.     

Influence of target temperature on femtosecond laser-ablated brass plasma spectroscopy

Spectral intensity,electron temperature and density of laser-induced plasma(LIP) are important parameters for affecting sensitivity of laser-induced breakdown spectroscopy(LIBS).Increasing target temperature is an easy and feasible method to improve the sensitivity.In this paper,a brass target in a temperature range from 25℃ to 200℃ was ablated to generate the LIP using femtosecond pulse.Time-resolved spectral emission of the femtosecond LIBS was measured under different target temperatures.The results showed that,compared with the experimental condition of 25℃,the spectral intensity of the femtosecond LIP was enhanced with more temperature target.In addition,the electron temperature and density were calculated by Boltzmann equation and Stark broadening,indicating that the changes in the electron temperature and density of femtosecond LIP with the increase of the target temperature were different from each other.By increasing the target temperature,the electron temperature increased while the electron density decreased.Therefore,in femtosecond LIBS,a hightemperature and low-density plasma with high emission can be generated by increasing the target temperature.The increase in the target temperature can improve the resolution and sensitivity of femtosecond LIBS.     

Influence of target temperature on AlO emission of femtosecond laser-induced Al plasmas

The influence of the target temperature on the molecular emission of femtosecond laser-induced breakdown spectroscopy(LIBS) was investigated experimentally. An Al target was ablated to produce laser-induced plasma. The Al target was uniformly heated to a maximum of 250℃. The measured molecular emission was AlO(△ν=0) from the femtosecond LIBS of the Al target.The measurements indicated that the molecular emission of AlO increased as the temperature of the Al target increased. In addition, a two-temperature model was used to simulate the evolution of the electron and lattice temperature of the Al target with different initial temperatures. The simulated results showed that the electron and lattice temperatures of Al irradiated by the femtosecond laser increased as the initial temperature of the Al target increased; also, the simulated ablated depth increased. Therefore, an increase in the initial Al target temperature resulted in an enhancement in the spectral signal of AlO from the femtosecond LIBS of Al,which was directly related to the increase in the size of the ablated crater. The study suggested that increasing the temperature of the target improves the intensity of molecular emission in femtosecond LIBS.     

Experimental Research on Plasma Induced by TEA CO2 Laser Propulsion

Results in the air-breathing propulsion experiments with a parabolic light craft and a self-made UV-preionized 100 J TEA CO2 laser device are presented. Air disturbance and the spectrum of the plasma after the interaction of pulsed laser radiation with the light craft were studied. It was found that the focal length of the parabolic light craft had a significant effect on the air-disturbance. Two shock waves were detected for the longer focal length, while only one shock wave detected for the short focal length. The spectrum of the laser-induced plasma, the distribution of the characteristic lines, and the temporal behaviors of the air plasma were studied in detail. The results showed that, the evolution of the laser-induced plasma lasted 20μs, and the plasma spectrum would reach the maximum intensity at 7μs.     

The Enhanced Effect of Optical Emission from Laser Induced Breakdown Spectroscopy of an Al-Li Alloy in the Presence of Magnetic Field Confinement

In this paper,the influence of magnetic field strength on laser-induced breakdown spectroscopy(LIBS) has been investigated for various pressures.The plasma plume was produced by employing Q-switch Nd:YAG laser ablation of an Al-Li alloy operating at a 1064 nm wavelength.The results indicated that the LIBS intensity of the Al and Li emission lines is boosted with an increase of magnetic strength.Typically,the intensity of the Al Ⅰ and Li Ⅰ spectral emissions can be magnified by 1.5-3 times in a steady magnetic field of 1.1 T compared with the field-free case.Also,in this investigation we recorded time-resolved images of the laser-produced plume by employing a fast ICCD camera.The results show that the luminance of the plasma is enhanced and the time of persistence is increased significantly,and the plasma plume splits into two lobes in the presence of a magnetic field.The probable reason for the enhancement is the magnetic confinement effect which increases the number density of excited atoms and the population of species in a high energy state.In addition,the electron temperature and density are also augmented by the magnetic field compared to the field-free case.     

Effect of N_2 and O_2 on OH radical production in an atmospheric helium microwave plasma jet

UV-pulsed laser cavity ringdown spectroscopy of the hydroxyl radical OH(A–X)(0–0)band in the wavelength range of 306–310 nm was employed to determine absolute number densities of OH in the atmospheric helium plasma jets generated by a 2.45 GHz microwave plasma source.The effect of the addition of molecular gases N_2 and O_2 to He plasma jets on OH generation was studied.Optical emission spectroscopy was simultaneously employed to monitor reactive plasma species.Stark broadening of the hydrogen Balmer emission line(H_β)was used to estimate the electron density nein the jets.For both He/N_2 and He/O_2 jets, newas estimated to be on the order of 10~(15)cm~(-3).The effects of plasma power and gas flow rate were also studied.With increase in N_2 and O_2 flow rates, netended to decrease.Gas temperature in the He/O_2 plasma jets was elevated compared to the temperatures in the pure He and He/N_2 plasma jets.The highest OH densities in the He/N_2 and He/O_2 plasma jets were determined to be 1.0?×10~(16)molecules/cm~3 at x?=?4 mm(from the jet orifice)and 1.8?×?10~(16)molecules/cm~3 at x=3 mm, respectively.Electron impact dissociation of water and water ion dissociative recombination were the dominant reaction pathways, respectively, for OH formation within the jet column and in the downstream and far downstream regions.The presence of strong emissions of the N_2~+ bands in both He/N_2 and He/O_2 plasma jets, as against the absence of the N_2~+ emissions in the Ar plasma jets, suggests that the Penning ionization process is a key reaction channel leading to the formation of N_2~+ in these He plasma jets.     

Spatio-temporal evaluation of Zr plasma parameters in a single-beam-splitting double-pulse laser-induced plasma

The plasma shielding effect is one of the major weaknesses of laser-induced breakdown spectroscopy(LIBS) as it causes non-linearity in signal strength. Although LIBS is typically carried out in constant laser energy, this non-linearity causes a reduction in sensitivity. In this work, we systematically examine laser-induced plasma, formed by two different excitation source modes, i.e. single pulse(SP)-excitation and single-beam-splitting double-pulse(SBSDP)-excitation over Zr-2.5% Nb alloy. The two most important plasma parameters influencing the emission line intensity, plasma temperature(T_e) and electron density(N_e) were studied and compared for both modes of laser excitation. Comparison of the results conclusively demonstrates that due to the splitting of the laser energy in the SBS-DP mode, the plasma shielding effect is significantly reduced. The reduced plasma shielding translates to an increased laser–sample coupling under SBS-DP mode. Temporal imaging of the total intensity of the laserinduced plasma in both excitation modes was also studied. The study shows how the plasma shielding effect can be reduced to improve the analytical quality of the LIBS methodology.     

Detection of Al,Mg, Ca,and Zn in copper slag by LIBS combined with calibration curve and PLSR methods

The precise measurement of Al, Mg, Ca, and Zn composition in copper slag is crucial for effective process control of copper pyrometallurgy. In this study, a remote laser-induced breakdown spectroscopy(LIBS) system was utilized for the spectral analysis of copper slag samples at a distance of 2.5 m. The composition of copper slag was then analyzed using both the calibration curve(CC) method and the partial least squares regression(PLSR) analysis method based on the characteristic spectral intensi...     

Characteristics of Plasma Jets in Laser-Driven Magnetic Reconnection

The jets driven by magnetic reconnection in laser-plasma interactions are investigated experimentally.The diagnostics in the optical and X-ray ranges provide detailed information about the jet characteristics.The plasma jets perpendicular to and along the target surface are observed clearly,which is evident signatures of laser driven magnetic reconnection.The jet formation is also investigated for different experimental parameters.     

The Plasma Channel Evolution Characteristics of Pulsed Flashlamps Working in an Array

This work is devoted to the study of plasma channel evolution characteristics in pulsed xenon flashlamps working in an array. Influencing factors on the plasma channel evolution process are studied, including pre-ionization pulse and neighbor flashlamps. It has been found that neighbor flashlamps affect the plasma channel by shaping the electric potential distribution, rather than by Lorentz force. Branching is observed in the plasma channels of the flashlamps in the middle of the array. Inconsistency also exists in the plasma channels of these flashlamps in different tests. The branching and inconsistency are both caused by the unique electric field distribution in these flashlamps. Besides, the pre-ionization pulse can help the main pulse plasma channel to develop more smoothly and faster, which will weaken the shock wave and benefit the mechanical strength of the flashlamp.     

Physical-Chemical Characterization of Nanodispersed Powders Produced by a Plasma-Chemical Technique

This article presents a review on the physical-chemical properties and characteristics of plasma-chemically produced nanodispersed powders （NDP）, such as metals, oxides, nitrides, carbides, and catalysts. The plasma-chemical preparatior~ of the powders was carried out in thermal plasma （TP） created by means of high-current electric arcs, plasma jets, high-frequency （HF） discharges, etc. We also discuss certain properties and characteristics of the NDPs, which are determined largely by the conditions of preparation.     

Analysis of Pulverized Coal by Laser-Induced Breakdown Spectroscopy

Laser-induced breakdown spectroscopy （LIBS） has been used to detect atomic species in various enviromnents. The quantitative analysis （C, H, O, N and S） of representative coal samples are being carried out with LIBS, and the effects of particle size are analyzed. A powerful pulse Nd：YAG laser is focused on the coal sample at atmosphere pressure, and the emission spectra from laser-induced plasmas are measured by time-resolved spectroscopy, and the intensity of analyzed spectral lines is obtained through observing the laser plasma with a delay time of 0.4 #s. The experimental results show that the slope of calibration curve is nearly 1 when the concentration of the analyzed element is relatively low, and the slope of curve is nearly 0.5 when the concentration of C is higher than other elements. In addition, using the calibration-free model without self-absorption effect, the results show that the decreasing of particle size leads to an increase of the plasma temperature.     

Spectral Characteristics of Laser-Induced Graphite Plasma in Ambient Air

An experimental setup of laser-induced graphite plasma was built and the spectral characteristics and properties of graphite plasma were studied. From the temporal behavior of graphite plasma, the duration of CN partials(B~2∑~+→X~2∑~+) emission was two times longer than that of atomic carbon, and all intensities reached the maximum during the early stage from0.2 μs to 0.8 μs. The electron temperature decreased from 11807 K to 8755 K, the vibration temperature decreased from 8973 K to 6472 K, and the rotational temperature decreased from7288 K to 4491 K with the delay time, respectively. The effect of the laser energy was also studied, and it was found that the thresholds and spectral characteristics of CN molecular and C atomic spectroscopy presented great differences. At lower laser energies, the electron excited temperature, the electron density, the vibrational temperature and rotational temperature of CN partials increased rapidly. At higher laser energies, the increasing of electron excited temperature and electron density slow down, and the vibrational temperature and rotational temperature even trend to saturation due to plasma shielding and dissociation of CN molecules. The relationship among the three kinds of temperatures was T_(elec)T_(vib)T_(rot) at the same time. The electron density of the graphite plasma was in the order of 10~(17)cm~(-3) and 10~(18)cm~(-3).     

Discharge characteristics of a needle-toplate electrode at a micro-scale gap

To understand the discharge characteristics under a gap of micrometers,the breakdown voltage and current–voltage curve are measured experimentally in a needle-to-plate electrode at a microscale gap of 3–50 μm in air.The effect of the needle radius and the gas pressure on the discharge characteristics are tested.The results show that when the gap is larger than 10 μm,the relation between the breakdown voltage and the gap looks like the Paschen curve;while below 10 μm,the breakdown voltage is nearly constant in the range of the tested gap.However,at the same gap distance,the breakdown voltage is still affected by the pressure and shows a trend similar to Paschen's law.The current–voltage characteristic in all the gaps is similar and follows the trend of a typical Townsend-to-glow discharge.A simple model is used to explain the non-normality of breakdown in the micro-gaps.The Townsend mechanism is suggested to control the breakdown process in this configuration before the gap reduces much smaller in air.