A -90-dB THD rail-to-rail input opamp using a new local charge pumpin CMOS

This paper describes the principle and design of a CMOS rail-to-rail input operational amplifier with THD performance of -90 dB which is suited for high-quality audio systems. A new output stage has been used featuring an output suing that extends to either supply rail and is capable of driving a low ohmic load (32 Ω). The opamp, which is realized in a 0.5-μm 3.3-V digital CMOS process, uses a standard two-stage Miller configuration. The rail-to-rail input functionality is achieved with a new area-efficient on-chip charge pump which provides the local supply voltage for the input differential pair. THD levels below -90 dB have not yet been shown with existing rail-to-rail techniques. This rail-to-rail input configuration also behaves independently of the common mode level with respect to transconductance and slewing characteristics     

Constant-g/sub m/ constant-slew-rate high-bandwidth low-voltage rail-to-rail CMOS input stage for VLSI cell libraries

This paper introduces a general-purpose low-voltage rail-to-rail input stage suitable for analog and mixed-signal applications. The proposed circuit provides, simultaneously, constant small-signal and large-signal behaviors over the entire input common-mode voltage range, while imposing no appreciable constraint for high-frequency operation. In addition, the accuracy of the circuit does not rely on any strict matching of the devices, unlike most of the traditional approaches based on complementary input pairs, which need to compensate for the difference in mobility between electrons and holes with the transistor aspect ratios. Also, the technique is compatible with deep submicrometer CMOS devices, where the familiar voltage-to-current square law in saturation is not completely satisfied. Based on the proposed input stage, a transconductor with rail-to-rail input common-mode range and an input/output rail-to-rail operational amplifier were developed. Both cells were designed to operate with a 3-V single supply and fabricated in standard 0.8-/spl mu/m CMOS technology. Experimental results are provided.     

Ultra low-voltage CMOS transconductance amplifiers

Simple and symmetrical ultra low-voltage current mode analog circuits and autozeroing amplifiers are presented. The low-voltage analog circuits are based on low-voltage inverters resembling precharge digital logic. Ultra low-voltage analog circuits can be operated at supply voltages down to 250?mV with rail-to-rail input and output swing. The output current of the ultra low-voltage symmetrical transconductance amplifier can be quite large due to a current boost technique. Ultra low-voltage analog circuits can be operated at supply voltages down to 250?mV with rail- to-rail input and output swing. The current headroom is 3???A and the supply voltage is 300?mV. For supply voltages down to 300?mV simulated data shows that the maximum clock frequency is approximately 600?MHz.     

A Low-Voltage Fully Differential Constant-Gm Rail-to-Rail CMOS Operational Amplifier

A low-voltage fully differential CMOS operational amplifier withconstant-g_mand rail-to-rail input and output stages ispresented. It is the fully differential version of a previously realizedsingle-ended operational amplifier where a novel circuit to ensure constanttransconductance has been implemented [1]. The input stage is a rail-to-railstructure formed by two symmetrical OTAs in parallel (the input transistorsare operating in weak inversion). The class-AB output stages have also afull voltage swing. A rail-to-rail input common mode feedback structureallows the output voltage control. Measurements in a 0.7 µ standardCMOS process with threshold voltages of about 0.7 V have been done. Theminimum experimental supply voltage is about 1.1 V. The circuit provides a60 dB low frequency voltage gain and about 1.5 MHz unity gain frequency fora total power consumption of about 0.72 mW at a 1.5 V supply voltage.     

一种0.8V衬底驱动轨对轨运算放大器设计

采用衬底驱动技术设计低压低功耗轨对轨运算放大器。输入级采用衬底驱动MOSFET,有效避开阈值电压限制,将电源电压降至0.8V,实现低压下轨对轨共模输入范围。增加衬底驱动冗余差分对及反折式共源共栅求和电路实现恒定跨导控制,消除共模电压对输入级跨导的影响,输出采用前馈式AB类输出级,以提高动态输出电压范围。基于标准0.18μmCMOS工艺仿真运放,测得输出范围0.4～782.5mV,功耗48.8μW,电源抑制比58dB,CMRR65dB,直流开环增益63.8dB,单位增益带宽2.4MHz,相位裕度68°。版图设计采用双阱交叉空铅技术,面积为97.8μm×127.6μm。     

一个低噪声轨到轨输入输出范围的运算放大器

设计了一个轨到轨输入输出范围的低噪声运算放大器.在输入级采用电流补偿的方法来稳定该运算放大器在整个输入共模范围内的跨导,在输出级使用AB类的输出方法来提高运算放大器的输出范围,并运用双极晶体管比较低的闪烁噪声来改善该运算放大器的噪声性能,以此提高该运算放大器的动态范围.     

1-V Rail-to-Rail CMOS OpAmp With Improved Bulk-Driven Input Stage

This paper introduces a CMOS operational amplifier with rail-to-rail input and output voltage ranges, suitable for operation in extremely low-voltage environments. The approach is based on a bulk-driven input stage with extended input common-mode voltage range, in which the effective input transconductance is enhanced by means of a partial positive feedback loop. As a result, a gain and gain-bandwidth product performance similar to that of an amplifier using a gate-driven approach is obtained. Output rail-to-rail operation is achieved by means of a push-pull stage, which is biased in class-AB by using a static feedback loop, thus avoiding frequency limitations inherent in dynamic-feedback tuning schemes. The proposed two-stage operational amplifier was designed to operate with a 1-V supply, and a test chip prototype was fabricated in 0.35-mum standard CMOS technology. The experimental performance features an open-loop DC gain higher than 76 dB and a closed-loop unity-gain bandwidth above 8 MHz when a 1-MOmegapar17-pF load is connected to the amplifier output     

A high current drive CMOS output stage with a tunable quiescent current limiting circuit

A CMOS output stage based on a complementary common source with an original quiescent current limiting circuit is presented. The quiescent current can be varied over a wide range by means of a control current with no need to modify the transistor aspect ratios. The output stage has been coupled to a conventional complementary input stage to form a rail-to-rail buffer. A prototype with the inclusion of auxiliary pins for biasing and current monitoring purposes has been designed using the 1-/spl mu/m double-polysilicon BCD3S process of STMicroelectronics. On a single 5-V power supply, the maximum output current is 20 mA. The amplifier, biased for a total power dissipation of 1 mW, exhibits a total harmonic distortion of -58 dB at 1 kHz with 4-V peak-to-peak on a 330-/spl Omega/ load. Correct operation of the quiescent current limiting circuit has been demonstrated for a minimum supply voltage of 2.2 V.     

Low Voltage CMOS Power Amplifier with Rail-to-Rail Input and Output

This paper describes a CMOS power amplifier with rail-to-rail input and output, also suitable for low voltage applications. The amplifier uses Simple Miller Compensation with high bandwidth stage to robustly and power efficiently compensate the amplifier. Circuit also includes a common mode adapter block, based on resistive level shift network, to implement rail-to-rail input and optional adaptive biasing block, which can be used to extend bandwidth of the amplifier for large high frequency inputs in continuous-time applications. Measurement results show that the amplifier is capable of driving heavy resistive and capacitive loads having maximum output current exceeding 100 mA, when driving 1 nF ‖ 10 Ω load from 3.0 V supply. Without adaptive biasing the linear amplifier achieves 5.7 MHz unity gain frequency and 61^∘ phase margin when driving 1 nF ‖ 1 kΩ load, while drawing 2.4 mA from 1.5 V supply.     

一种基于准浮栅技术的折叠差分结构及其应用

提出了一种基于准浮栅技术的新型折叠差分结构,其偏置电流源的电压降被折叠到输出电压摆幅中,且不受共模输入电压限制而达到较大范围,非常适于低压应用。基于此结构,实现了一种超低压运算放大器。仿真分析表明,该运算放大器能够实现轨到轨(rail-to-rail)的共模输入电压范围和输出电压摆幅,以及较高的共模抑制比。     

一种低失调高压大电流集成运算放大器

基于结型场效应晶体管(JFET)和双极型晶体管(BJT)兼容工艺,设计了一种低失调高压大电流集成运算放大器。电路输入级采用p沟道JFET (p-JFET)差分对共源共栅结构;中间级以BJT作为放大管,采用复合有源负载结构;输出级采用复合npn达林顿管阵列,与常规推挽输出结构相比,在输出相同电流的情况下,节省了大量芯片面积。基于Cadence Spectre软件对该运算放大器电路进行了仿真分析和优化设计,在±35 V电源供电下,最小负载电阻为6Ω时的电压增益为95 dB,输入失调电压为0.224 5 mV,输入偏置电流为31.34 pA,输入失调电流为3.3 pA,单位增益带宽为9.6 MHz,具有输出9 A峰值大电流能力。     

Effective parameter extraction using multiple-objective function for VLSI circuits

In this paper an input stage and an output stage are presented for application in low-voltage CMOS operational amplifiers. The input stage operates in strong inversion and has a rail-to-rail common-mode input voltage range. The transconductance (g _m ) is insensitive to the common-mode input voltage. The class AB output stage has a rail-to-rail output range. A class AB control circuit prevents any transistors in the output stage from switching off. This improves the large-signal high-frequency behavior and the step response of the amplifier. A complete two-stage Op Amp employing the proposed input and output stages was realized in a semi-custom CMOS process with minimum channel lengths of 10µm and transistor threshold voltages of approximately 0.7 V. The measured minimum supply voltage is 2.5 V. The measured input voltage range exceeds the supply rails and the output voltage reaches both rails within 130 mV. The unity-gain bandwidth of the complete Op Amp is severely limited by the long channel lengths. Simulations show that a unity-gain bandwidth of 7 MHz is feasible if 2.5µm channel lengths are used.     

A 0.9-V 0.5-μA rail-to-rail CMOS operational amplifier

A 0.9-V 0.5-μA, rail-to-rail CMOS operational amplifier designed with weak inversion techniques is presented. Depletion-mode nMOS transistors buffer a bulk-driven pMOS differential pair to realize wide input dynamic range, while the output stage architecture provides symmetric rail-to-rail output drive through the use of a low-voltage translinear control circuit     

Class AB CMOS amplifiers with high efficiency

A new class AB CMOS operational-amplifier principle is presented. A transconductance amplifier based on this principle exhibits small-signal characteristics comparable to those of a conventional OTA. It has, however, a superior current efficiency and its settling time is not slew-rate limited. The new class AB principle can also be used in an output stage with a well-defined quiescent current, a rail-to-rail output swing, and a good driving capability. A two-stage amplifier with both the input and output stages based on the new principle has been realized. It features a rail-to-rail input and output common-mode range, a gain-bandwidth of 370-kHz, a settling time of less than 5 μs independent of the applied step, and a power consumption of 247 μW. It drives a resistive load of 3 kΩ in parallel with a capacitive load of 400 pF when operated on a 2.5-V/-2.5-V power supply     

低压低功耗运算放大器结构设计技术

低电压、低功耗、动态摆幅达到轨到轨（Rail—to—Rail）的运放是实现SOC设计的核心，而相关的输入输出模块是其中的关键技术。本文分析了两种分别工作于弱反型区和强反型区的恒跨导Rail—to—Rail输入级，同时给出了低压和极低压下两种AB类控制输出级的实现方案，并对各方案进行了比较和总结。     

Novel low-voltage ultra-low-power DVCC based on floating-gate folded cascode OTA

In this paper a novel low-voltage ultra-low-power differential voltage current conveyor (DVCC) based on folded cascode operational transconductance amplifier OTA with only one differential pairs floating-gate MOS transistor (FG-MOST) is presented. The main features of the proposed conveyor are: design simplicity; rail-to-rail input voltage swing capability at a low supply voltage of ±0.5 V; and ultra-low-power consumption of mere 10 μW. Thanks to these features, the proposed circuit could be successfully employed in a wide range of low-voltage ultra-low-power analog signal processing applications. Implementation of new multifunction frequency filter based on the proposed FG-DVCC is presented in this paper to take the advantages of the properties of the proposed circuit. PSpice simulation results using 0.18 μm CMOS technology are included as well to validate the functionality of the proposed circuit.     

Single-pair bulk-driven CMOS input stage: A compact low-voltage analog cell for scaled technologies

Bulk-driven MOS transistors lead to a compact low-voltage/low-power input stage implementation. This paper illustrates the rail-to-rail capability of a single-pair bulk-driven CMOS input stage operated from an extremely low supply voltage. A composite input stage is also introduced to point out some limitations inherent in multiple-pair input stages and carry out performance comparison, based on experimental data obtained in standard 0.35 μm CMOS technology. The performance achieved by the single-pair bulk-driven input stage can be readily extended to a nanoscale process, as lower supply voltages in scaled technologies are expected. Measurements demonstrate the rail-to-rail suitability of the single-pair input stage and show intrinsic advantages of this approach in some amplifier features, such as linearity and common-mode rejection ratio, as compared to the case of the composite solution.     

CMOS low-voltage operational amplifiers with constant-gm rail-to-rail input stage

Two 3.3-V operational amplifiers with constant-g _m rail-to-rail input stage and rail-to-rail output stage are presented. The constant transconductance (g _m ) ensures a constant unity-gain frequency within the whole commonmode input range. Two new methods to control theg _m are introduced. Both operational amplifiers use the same rail-to-rail output stage. The operational amplifiers have been integrated in a CMOS semicustom process with transistor lengths of 10µm. The common-mode input voltage swing extends beyond the positive supply rail by 400 mV and beyond the negative supply rail by 200 mV. The output voltage is able to reach within 130 mV of the supply rails. The output current of the operational amplifiers is 2 mA and the voltage gain is 85 dB. The unity-gain frquency is 165 kHz, which is mainly limited by the relatively long transistor lengths of 10µm. In another process with channel lengths of 2µm, simulation results showed that a unity-gain frequency of 4 MHz can easily be obtained.     

A 3.2-V operation single-chip dual-band AlGaAs/GaAs HBT MMIC poweramplifier with active feedback circuit technique

This paper describes the design and experimental results for a 3.2-V operation single-chip AlGaAs/GaAs heterojunction bipolar transistor (HBT) monolithic microwave integrated circuit (IMMIC) power amplifier for GSM900 and DCS1800 dual-band applications. The following two new circuit techniques are proposed for implementing the power amplifier. One is an on-chip HBT bias switch which in turn switches the amplifier between 900 and 1800 MHz. The proposed switch configuration allows the switch using a high turn-on voltage of 1.3 V of AlGaAs/GaAs HBT's to operate with a 3-V low supply voltage, because the switch circuitry needs no stacked configuration. The other is an active feedback circuit (AFB) to prevent permanent failure of HBT's in the output power stage even under severe conditions of oversupply voltage and strongly mismatching load. Experimental results revealed that the proposed feedback circuit, which works as a voltage limiter, can protect the output stage HBT's from an excessive collector voltage swing even when the amplifier is operated under a condition of a 5-V oversupply voltage and a 10:1 voltage standing-wave ratio (VSWR) mismatching load. Under a normal condition of 3.2 V and a 50-Ω matching load, the IC is capable of delivering an output power of 34.5 dBm and a power-added efficiency (PaE) of 52% in a GSM900 mode, and a 32-dBm output power and a 32% PAE in a DCS1800 mode     

Operational amplifier with 1-V rail-to-rail multipath-driven outputstage

A bipolar operational amplifier (op amp) with a rail-to-rail multipath-driven output stage that operates at supply voltages down to 1 V is presented. The bandwidth of this output stage is as high as possible, viz, equal to that of one of the output transistors, loaded by the output capacitance. The output voltage can reach both supply rails within 100 mV and the output current is ±15 mA. The op amp is designed to be loaded by a 100-pF capacitor and the unity-gain bandwidth is 3.4 MHz at a 60° phase margin. The voltage gain is 117 dB and the CMRR is 100 dB. The frequency behavior of the multipath-driven (MPD) topology has an improved performance when compared to that of previously presented low-voltage output stages. A figure of merit F_M for low-voltage op amps has been defined as the bandwidth-power ratio