Diameter control of carbon nanotubes by changing the concentration of catalytic metal ion solutions

We have developed a simple new method to control the diameter of carbon nanotubes (CNTs) using catalytic nanoparticle arrays fabricated by filling the pores of well-ordered porous anodic aluminum oxide (AAO) templates with a metal ion solution. Fe ion solution was used to fill the pores in which Co had been deposited electrochemically, and then the template was dried naturally on a magnet. After this process, the pores were widened in NaOH solution. Well-graphitized multi-walled CNTs were grown from almost all the pores and were very long in length and homogeneous in diameter. We were able to control the diameter of CNTs, simply, by changing the concentration of iron ion solution. For example, the average outer diameters of the CNTs are 7 ± 1.5, 13 ± 1, and 17 ± 1 nm when the concentrations of Fe ion in their mother solutions were 1.0 × 10⁻³, 3.0 × 10⁻³, and 6.0 × 10⁻³ M, respectively. The inner diameters of these CNTs corresponded to the calculated diameters of Fe nanoparticles by assuming that all Fe ions contained in each pore are reduced to a single nanoparticle. This means that homogeneous nanoparticles are made in each pore. Our new method could be used to fabricate homogeneous nanoparticles from most metal ion solutions.     

Modification of Thin Film Composite PVA/PAN Membranes for Pervaporation Using Aluminosilicate Nanoparticles

The effect of the modification of the polyvinyl alcohol (PVA) selective layer of thin film composite (TFC) membranes by aluminosilicate (Al₂O₃·SiO₂) nanoparticles on the structure and pervaporation performance was studied. For the first time, PVA-Al₂O₃·SiO₂/polyacrylonitrile (PAN) thin film nanocomposite (TFN) membranes for pervaporation separation of ethanol/water mixture were developed via the formation of the selective layer in dynamic mode. Selective layers of PVA/PAN and PVA-Al₂O₃·SiO₂/PAN membranes were formed via filtration of PVA aqueous solutions or PVA-Al₂O₃·SiO₂ aqueous dispersions through the ultrafiltration PAN membrane for 10 min at 0.3 MPa in dead-end mode. Average particle size and zeta potential of aluminosilicate nanoparticles in PVA aqueous solution were analyzed using the dynamic light scattering technique. Structure and surface properties of membranes were studied using scanning electron microscopy (SEM), atomic force microscopy (AFM) and water contact angle measurements. Membrane performance was investigated in pervaporation dehydration of ethanol/water mixtures in the broad concentration range. It was found that flux of TFN membranes decreased with addition of Al₂O₃·SiO₂ nanoparticles into the selective layer due to the increase in selective layer thickness. However, ethanol/water separation factor of TFN membranes was found to be significantly higher compared to the reference TFC membrane in the whole range of studied ethanol/water feed mixtures with different concentrations, which is attributed to the increase in membrane hydrophilicity. It was found that developed PVA-Al₂O₃·SiO₂/PAN TFN membranes were more stable in the dehydration of ethanol in the whole range of investigated concentrations as well as at different temperatures of the feed mixtures (25 °C, 35 °C, 50 °C) compared to the reference membrane which is due to the additional cross-linking of the selective layer by formation hydrogen and donor-acceptor bonds between aluminosilicate nanoparticles and PVA macromolecules.     

Near-infrared optical absorption enhanced in black silicon via Ag nanoparticle-induced localized surface plasmon

Due to the localized surface plasmon (LSP) effect induced by Ag nanoparticles inside black silicon, the optical absorption of black silicon is enhanced dramatically in near-infrared range (1,100 to 2,500 nm). The black silicon with Ag nanoparticles shows much higher absorption than black silicon fabricated by chemical etching or reactive ion etching over ultraviolet to near-infrared (UV-VIS-NIR, 250 to 2,500 nm). The maximum absorption even increased up to 93.6% in the NIR range (820 to 2,500 nm). The high absorption in NIR range makes LSP-enhanced black silicon a potential material used for NIR-sensitive optoelectronic device.

PACS

78.67.Bf; 78.30.Fs; 78.40.-q; 42.70.Gi     

Gas sensing properties of conducting polymer/Au-loaded ZnO nanoparticle composite materials at room temperature

In this work, a new poly (3-hexylthiophene):1.00 mol% Au-loaded zinc oxide nanoparticles (P3HT:Au/ZnO NPs) hybrid sensor is developed and systematically studied for ammonia sensing applications. The 1.00 mol% Au/ZnO NPs were synthesized by a one-step flame spray pyrolysis (FSP) process and mixed with P3HT at different mixing ratios (1:1, 2:1, 3:1, 4:1, and 1:2) before drop casting on an Al₂O₃ substrate with interdigitated gold electrodes to form thick film sensors. Particle characterizations by X-ray diffraction (XRD), nitrogen adsorption analysis, and high-resolution transmission electron microscopy (HR-TEM) showed highly crystalline ZnO nanoparticles (5 to 15 nm) loaded with ultrafine Au nanoparticles (1 to 2 nm). Film characterizations by XRD, field-emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray (EDX) spectroscopy, and atomic force microscopy (AFM) revealed the presence of P3HT/ZnO mixed phases and porous nanoparticle structures in the composite thick film. The gas sensing properties of P3HT:1.00 mol% Au/ZnO NPs composite sensors were studied for reducing and oxidizing gases (NH₃, C₂H₅OH, CO, H₂S, NO₂, and H₂O) at room temperature. It was found that the composite film with 4:1 of P3HT:1.00 mol% Au/ZnO NPs exhibited the best NH₃ sensing performances with high response (approximately 32 to 1,000 ppm of NH₃), fast response time (4.2 s), and high selectivity at room temperature. Plausible mechanisms explaining the enhanced NH₃ response by composite films were discussed.     

Reduction in thermal conductivity of Bi thin films with high-density ordered nanoscopic pores

We prepared two-dimensional Bi thin films with high-density ordered nanoscopic pores by e-beam evaporation of Bi metal. For this structure, we used polystyrene beads ranging from 200 to 750 nm in diameter as an etch mask. The typical hole and neck sizes of the Bi thin films with approximately 50 nm in thickness on SiO₂/Si substrates were in the range of 135 to 490 nm and 65 to 260 nm, respectively. By measuring the thermal characteristics through a 3ω technique, we found that the thermal conductivities of nanoporous Bi thin films are greatly suppressed compared with those of corresponding bulk materials. With a decrease in pore size to approximately 135 nm, the thermal conductivity decreased significantly to approximately 0.46 W/m·K at 300 K.     

Self-organizing nanodot structures on InP surfaces evolving under low-energy ion irradiation: analysis of morphology and composition

Surfaces of InP were bombarded by 1.9 keV Ar⁺ ions under normal incidence. The total accumulated ion fluence Φ the samples were exposed to was varied from 1 × 10¹⁷ cm⁻² to 3 × 10¹⁸ cm⁻², and ion fluxes f of (0.4 − 2) × 10¹⁴ cm⁻² s⁻¹ were used. The surface morphology resulting from these ion irradiations was examined by atomic force microscopy (AFM). Generally, nanodot structures are formed on the surface; their dimensions (diameter, height and separation), however, were found to depend critically on the specific bombardment conditions. As a function of ion fluence, the mean radius r, height h, and spacing l of the dots can be fitted by power-law dependences: r ∝ Φ^0.40, h ∝ Φ^0.48, and l ∝ Φ^0.19. In terms of ion flux, there appears to exist a distinct threshold: below f ~ (1.3 ± 0.2) × 10¹⁴ cm⁻² s⁻¹, no ordering of the dots exists and their size is comparatively small; above that value of f, the height and radius of the dots becomes substantially larger (h ~ 40 nm and r ~ 50 nm). This finding possibly indicates that surface diffusion processes could be important. In order to determine possible local compositional changes in these nanostructures induced by ion impact, selected samples were prepared for atom probe tomography (APT). The results indicate that APT can provide analytical information on the composition of individual InP nanodots. By means of 3D APT data, the surface region of such nanodots evolving under ion bombardment could be examined with atomic spatial resolution. At the InP surface, the values of the In/P concentration ratio are distinctly higher over a distance of approximately 1 nm and amount to 1.3 to 1.7.     

Size-controllable synthesis and bandgap modulation of single-layered RF-sputtered bismuth nanoparticles

We here report a simple and efficient method to grow single-layer bismuth nanoparticles (BiNPs) with various sizes on glass substrates. Optimal conditions were found to be 200°C and 0.12 W/cm² at a growth rate of 6 Å/s, with the deposition time around 40 s. Scanning electron microscope (SEM) images were used to calculate the particle size distribution statistics, and high-resolution X-ray diffraction (XRD) patterns were used to examine the chemical interactions between BiNPs and the substrates. By measuring the transmission spectra within the range of 300 to 1,000 nm, we found that the optical bandgap can be modulated from 0.45 to 2.63 eV by controlling the size of these BiNPs. These interesting discoveries offer an insight to explore the dynamic nature of nanoparticles.     

Morphological effect of oscillating magnetic nanoparticles in killing tumor cells

Forced oscillation of spherical and rod-shaped iron oxide magnetic nanoparticles (MNPs) via low-power and low-frequency alternating magnetic field (AMF) was firstly used to kill cancer cells in vitro. After being loaded by human cervical cancer cells line (HeLa) and then exposed to a 35-kHz AMF, MNPs mechanically damaged cell membranes and cytoplasm, decreasing the cell viability. It was found that the concentration and morphology of the MNPs significantly influenced the cell-killing efficiency of oscillating MNPs. In this preliminary study, when HeLa cells were pre-incubated with 100 μg/mL rod-shaped MNPs (rMNP, length of 200 ± 50 nm and diameter of 50 to 120 nm) for 20 h, MTT assay proved that the cell viability decreased by 30.9% after being exposed to AMF for 2 h, while the cell viability decreased by 11.7% if spherical MNPs (sMNP, diameter of 200 ± 50 nm) were used for investigation. Furthermore, the morphological effect of MNPs on cell viability was confirmed by trypan blue assay: 39.5% rMNP-loaded cells and 15.1% sMNP-loaded cells were stained after being exposed to AMF for 2 h. It was also interesting to find that killing tumor cells at either higher (500 μg/mL) or lower (20 μg/mL) concentration of MNPs was less efficient than that achieved at 100 μg/mL concentration. In conclusion, the relatively asymmetric morphological rod-shaped MNPs can kill cancer cells more effectively than spherical MNPs when being exposed to AMF by virtue of their mechanical oscillations.     

Efficient solar photocatalyst based on cobalt oxide/iron oxide composite nanofibers for the detoxification of organic pollutants

A Co₃O₄/Fe₂O₃ composite nanofiber-based solar photocatalyst has been prepared, and its catalytic performance was evaluated by degrading acridine orange (AO) and brilliant cresyl blue (BCB) beneath solar light. The morphological and physiochemical structure of the synthesized solar photocatalyst was characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FTIR). FESEM indicates that the Co₃O₄/Fe₂O₃ composite has fiber-like nanostructures with an average diameter of approximately 20 nm. These nanofibers are made of aggregated nanoparticles having approximately 8.0 nm of average diameter. The optical properties were examined by UV-visible spectrophotometry, and the band gap of the solar photocatalyst was found to be 2.12 eV. The as-grown solar photocatalyst exhibited high catalytic degradation in a short time by applying to degrade AO and BCB. The pH had an effect on the catalytic performance of the as-grown solar photocatalyst, and it was found that the synthesized solar photocatalyst is more efficient at high pH. The kinetics study of both AO and BCB degradation indicates that the as-grown nanocatalyst would be a talented and efficient solar photocatalyst for the removal of hazardous and toxic organic materials.     

Green synthesis of protein capped silver nanoparticles from phytopathogenic fungus Macrophomina phaseolina (Tassi) Goid with antimicrobial properties against multidrug-resistant bacteria

In recent years, green synthesis of nanoparticles, i.e., synthesizing nanoparticles using biological sources like bacteria, algae, fungus, or plant extracts have attracted much attention due to its environment-friendly and economic aspects. The present study demonstrates an eco-friendly and low-cost method of biosynthesis of silver nanoparticles using cell-free filtrate of phytopathogenic fungus Macrophomina phaseolina. UV-visible spectrum showed a peak at 450 nm corresponding to the plasmon absorbance of silver nanoparticles. Scanning electron microscopy (SEM), atomic force microscopy (AFM), and transmission electron microscopy (TEM) revealed the presence of spherical silver nanoparticles of the size range 5 to 40 nm, most of these being 16 to 20 nm in diameter. X-ray diffraction (XRD) spectrum of the nanoparticles exhibited 2θ values corresponding to silver nanoparticles. These nanoparticles were found to be naturally protein coated. SDS-PAGE analysis showed the presence of an 85-kDa protein band responsible for capping and stabilization of the silver nanoparticles. Antimicrobial activities of the silver nanoparticles against human as well as plant pathogenic multidrug-resistant bacteria were assayed. The particles showed inhibitory effect on the growth kinetics of human and plant bacteria. Furthermore, the genotoxic potential of the silver nanoparticles with increasing concentrations was evaluated by DNA fragmentation studies using plasmid DNA.     

Chitosan-Coated Magnetic Nanoparticles Prepared in One Step by Reverse Microemulsion Precipitation

Chitosan-coated magnetic nanoparticles (CMNP) were obtained at 70 °C and 80 °C in a one-step method, which comprises precipitation in reverse microemulsion in the presence of low chitosan concentration in the aqueous phase. X-ray diffractometry showed that CMNP obtained at both temperatures contain a mixture of magnetite and maghemite nanoparticles with ≈4.5 nm in average diameter, determined by electron microscopy, which suggests that precipitation temperature does not affect the particle size. The chitosan coating on nanoparticles was inferred from Fourier transform infrared spectrometry measurements; furthermore, the carbon concentration in the nanoparticles allowed an estimation of chitosan content in CMNP of 6%–7%. CMNP exhibit a superparamagnetic behavior with relatively high final magnetization values (≈49–53 emu/g) at 20 kOe and room temperature, probably due to a higher magnetite content in the mixture of magnetic nanoparticles. In addition, a slight direct effect of precipitation temperature on magnetization was identified, which was ascribed to a possible higher degree of nanoparticles crystallinity as temperature at which they are obtained increases. Tested for Pb²⁺ removal from a Pb(NO₃)₂ aqueous solution, CMNP showed a recovery efficacy of 100%, which makes them attractive for using in heavy metals ion removal from waste water.     

Diameter control of ultrathin zinc oxide nanofibers synthesized by electrospinning

Electrospinning is a versatile technique, which can be used to generate nanofibers from a rich variety of materials. We investigate the variation of a zinc oxide (ZnO)-polyvinylpyrrolidone (PVP) composite structure in morphology by electrospinning from a series of mixture solutions of ZnO sol–gel and PVP. Calcination conditions for the crystallization of ZnO nanofibers and removal of the PVP component from the ZnO-PVP composite nanofibers were also studied. The progression of the ZnO-PVP composite structure from grains to nanofibers was observed, and ZnO-PVP nanofibers as thin as 29.9 ± 0.8 nm on average were successfully fabricated. The size of the resultant ZnO-PVP composite nanofibers was considerably affected by two parameters: the concentrations of zinc acetate and PVP in the precursor solution. The concentration of zinc acetate particularly influenced the diameter distribution of the ZnO-PVP nanofibers. The ZnO-PVP nanofibers could be subsequently converted into ZnO nanofibers of a pure wurtzite phase via calcination in air at 500°C for 2 h.     

Amino acid sensing by impedance of porous monolith-type ion exchanger

A biological and chemical sensor with rapid response at the microlevel is required for health and environmental monitoring. To develop a high-performance sensor, we use a porous monolith-type ion exchanger having three-dimensional acceptors to sense chemical substances. This porous monolith-type ion exchanger has an open-cellular structure with 5-50-μm diameter pores. The concentration of amino acids in the solution can be detected by measuring the impedance of the monolith-type ion exchanger. The novel ion exchanger has a high-exchange rate and high-electrical conductivity compared with that of the conventional ion-exchange resins. It is found that the impedance of the porous ion exchanger varies widely, depending on the amino acids such as glycine, asparatic acid, lysine, and phenylalanine. The impedance of anion exchanger had the highest value for phenylalanine with a benzene ring. OH-ion conduction is suppressed possibly due to the phenylalanine molecules stabilized by the hydrophobic interaction with the anion exchanger. In addition, we succeeded in sensing amino acid ions with concentration as low as 10⁻⁷ mol. The porous ion exchanger has the potential of a high-performance device for biological and chemical sensing.     

Tuning of structural,optical, and magnetic properties of ultrathin and thin ZnO nanowire arrays for nano device applications

One-dimensional (1-D) ultrathin (15 nm) and thin (100 nm) aligned 1-D (0001) and (0001¯) oriented zinc oxide (ZnO) nanowire (NW) arrays were fabricated on copper substrates by one-step electrochemical deposition inside the pores of polycarbonate membranes. The aspect ratio dependence of the compressive stress because of the lattice mismatch between NW array/substrate interface and crystallite size variations is investigated. X-ray diffraction results show that the polycrystalline ZnO NWs have a wurtzite structure with a = 3.24 Å, c = 5.20 Å, and [002] elongation. HRTEM and SAED pattern confirmed the polycrystalline nature of ultrathin ZnO NWs and lattice spacing of 0.58 nm. The crystallite size and compressive stress in as-grown 15- and 100-nm wires are 12.8 nm and 0.2248 GPa and 22.8 nm and 0.1359 GPa, which changed to 16.1 nm and 1.0307 GPa and 47.5 nm and 1.1677 GPa after annealing at 873 K in ultrahigh vacuum (UHV), respectively. Micro-Raman spectroscopy showed that the increase in E₂ (high) phonon frequency corresponds to much higher compressive stresses in ultrathin NW arrays. The minimum-maximum magnetization magnitude for the as-grown ultrathin and thin NW arrays are approximately 8.45 × 10⁻³ to 8.10 × 10⁻³ emu/g and approximately 2.22 × 10⁻⁷ to 2.190 × 10⁻⁷ emu/g, respectively. The magnetization in 15-nm NW arrays is about 4 orders of magnitude higher than that in the 100 nm arrays but can be reduced greatly by the UHV annealing. The origin of ultrathin and thin NW array ferromagnetism may be the exchange interactions between localized electron spin moments resulting from oxygen vacancies at the surfaces of ZnO NWs. The n-type conductivity of 15-nm NW array is higher by about a factor of 2 compared to that of the 100-nm ZnO NWs, and both can be greatly enhanced by UHV annealing. The ability to tune the stresses and the structural and relative occupancies of ZnO NWs in a wide range by annealing has important implications for the design of advanced photonic, electronic, and magneto-optic nano devices.     

Ferromagnetism and optical properties of La1???x Al x FeO3 nanopowders

La_{1 − x} Al _x FeO₃ (x = 0.0, 0.05, 0.1, 0.2, 0.3, 0.4, and 0.5) nanopowders were prepared by polymerization complex method. All prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR), and UV-vis spectrophotometry (UV-vis). The magnetic properties were investigated using a vibrating sample magnetometer (VSM). The X-ray results of all samples show the formation of an orthorhombic phase with the second phase of α-Fe₂O₃ in doped samples. The crystallite sizes of nanoparticles decreased with increasing Al content, and they are found to be in the range of 58.45 ± 5.90 to 15.58 ± 4.64 nm. SEM and TEM images show the agglomeration of nanoparticles with average particle size in the range of 60 to 75 nm. The FT-IR spectra confirm the presence of metal oxygen bonds of O-Fe-O and Fe-O in the FeO₆ octahedra. The UV-vis spectra show strong absorption peaks at approximately 285 nm, and the calculated optical band gaps are found to be in the range of 2.05 to 2.09 eV with increasing Al content. The M-H loop of the pure sample is antiferromagnetic, whereas those of the doped samples tend to be ferromagnetic with increasing Al content. The magnetization, remanent magnetization, and coercive field of the Al-doped sample with x = 0.5 are enhanced to 1.665 emu/g, 0.623 emu/g, and 4,087.0 Oe, respectively.     

Thin and long silver nanowires self-assembled in ionic liquids as a soft template: electrical and optical properties

Thin and long silver nanowires were successfully synthesized using the polyvinylpyrrolidone (PVP)-assisted polyol method in the presence of ionic liquids, tetrapropylammonium chloride and tetrapropylammonium bromide, which served as soft template salts. The first step involved the formation of Ag nanoparticles with a diameter of 40 to 50 nm through the reduction of silver nitrate. At the growing stage, the Ag nanoparticles were converted into thin and long one-dimensional wires, with uniform diameters of 30 ± 3 nm and lengths of up to 50 μm. These Ag nanowires showed an electrical conductivity of 0.3 × 10⁵ S/cm, while the sheet resistance of a two-dimensional percolating Ag nanowire network exhibited a value of 20 Ω/sq with an optical transmittance of 93% and a low haze value.     

One-pot hydrothermal synthesis of Mn3O4 nanorods grown on Ni foam for high performance supercapacitor applications

Mn₃O₄/Ni foam composites were synthesized by a one-step hydrothermal method in an aqueous solution containing only Mn(NO₃)₂ and C₆H₁₂N₄. It was found that Mn₃O₄ nanorods with lengths of 2 to 3 μm and diameters of 100 nm distributed on Ni foam homogeneously. Detailed reaction time-dependent morphological and component evolution was studied to understand the growth process of Mn₃O₄ nanorods. As cathode material for supercapacitors, Mn₃O₄ nanorods/composite exhibited superior supercapacitor performances with high specific capacitance (263 F · g^-1 at 1A · g^-1), which was more than 10 times higher than that of the Mn₃O₄/Ni plate. The enhanced supercapacitor performance was due to the porous architecture of the Ni foam which provides fast ion and electron transfer, large reaction surface area, and good conductivity.     

Surface-enhanced Raman spectra of medicines with large-scale self-assembled silver nanoparticle films based on the modified coffee ring effect

We report here a simple and innovative method to prepare large-scale silver nanoparticle films based on the controlled coffee ring effect. It is demonstrated that the films can be used as surface-enhanced Raman scattering probes to detect low-concentration medicines. Silver nanoparticles with the average size about 70 nm were prepared by reduction of silver nitride. In our experiment, the coffee ring effect was controlled by tilting the substrates during the deposition of silver nanoparticle films. Silver nanoparticle films were spontaneously formed on the surface of silicon substrates at the temperatures about 50°C based on the solvent evaporation and the coffee ring effect. The microstructure of the films was investigated using the scanning electron microscope and atomic force microscope. The surface roughness of the films is found as small as 20 nm. Then, the films were exposed to aqueous solutions of medicine at different concentrations. A comparison with a Raman spectra measured with a conventional Raman spectrometer showed that the Raman signal can be detected in the solution with concentrations as low as 1 × 10⁻⁵ M, and the enhancement factor achieved by the silver nanoparticle film can at least reach to 1.08 × 10⁴. Our experimental results indicate that this technique is promising in the production of large-scale silver nanoparticle films for the surface-enhanced Raman scattering. These may be utilized in biochemical and trace analytical applications.     

Synthesis and characterization of PVA/PES thin film composite nanofiltration membrane modified with TiO2 nanoparticles for better performance and surface properties

Novel polyethersulfone (PES)/poly (vinyl alcohol) (PVA)/titanium dioxide (TiO₂) composite nanofiltration membranes were prepared by dip-coating of PES membrane in PVA and TiO₂ nanoparticles aqueous solution. Glutaraldehyde (GA) was used as a cross-linker for the composite polymer membrane in order to enhance the chemical, thermal as well as mechanical stabilities. TiO₂ nanoparticles with different concentrations (0, 0.05, 0.1, 0.5 wt.%) were coated on the surface of PVA/PES composite membrane. The morphological study was investigated by atomic force microscopy (AFM), scanning surface microscopy (SEM) and along with X-ray diffraction (XRD). In addition, the membranes performances, in terms of permeate flux, ion rejection and swelling factor were also investigated. It was found that the increase in TiO₂ solution concentration can highly affect the surface morphology and filtration performance of coated membranes. The contact angle measurement and XRD studies indicated that the TiO₂ nanoparticles successfully were coated on the surface of PVA/PES composite membranes. However, rougher surface was obtained for membranes by TiO₂ coating. The filtration performance data showed that the 0.1 wt.% TiO₂-modified membrane presents higher performance in terms of flux and NaCl salt rejection. Finally, TiO₂ modified membranes demonstrated the lower degree of swelling.     

Microwave-assisted green synthesis of Ag/reduced graphene oxide nanocomposite as a surface-enhanced Raman scattering substrate with high uniformity

A nanocomposite of silver nanoparticles/reduced graphene oxide (Ag/rGO) has been fabricated as a surface-enhanced Raman scattering (SERS) substrate owing to the large surface area and two-dimensional nanosheet structure of rGO. A facile and rapid microwave-assisted green route has been used for the formation of Ag nanoparticles and the reduction of graphene oxide simultaneously with L-arginine as the reducing agent. By increasing the cycle number of microwave irradiation from 1 and 4 to 8, the mean diameters of Ag nanoparticles deposited on the surface of rGO increased from 10.3 ± 4.6 and 21.4 ± 10.5 to 41.1 ± 12.6 nm. The SERS performance of Ag/rGO nanocomposite was examined using the common Raman reporter molecule 4-aminothiophenol (4-ATP). It was found that the Raman intensity of 4-ATP could be significantly enhanced by increasing the size and content of silver nanoparticles deposited on rGO. Although the Raman intensities of D-band and G-band of rGO were also enhanced simultaneously by the deposited Ag nanoparticles which limited the further improvement of SERS detection sensitivity, the detectable concentration of 4-ATP with Ag/rGO nanocomposite as the SERS substrate still could be lowered to be 10⁻¹⁰ M and the enhancement factor could be increased to 1.27 × 10¹⁰. Furthermore, it was also achievable to lower the relative standard deviation (RSD) values of the Raman intensities to below 5%. This revealed that the Ag/rGO nanocomposite obtained in this work could be used as a SERS substrate with high sensitivity and homogeneity.