Dielectric properties of a new ceramic system (1 − x)Mg4Nb2O9-xCaTiO3 at microwave frequency

The microstructures and the microwave dielectric properties of the (1 − x)Mg₄Nb₂O₉-xCaTiO₃ ceramic system were investigated. In order to achieve a temperature-stable material, CaTiO₃ (τ_f ∼ 800 ppm/°C) was chosen as a τ_f compensator and added to Mg₄Nb₂O₉ (τ_f ∼ −70 ppm/°C) to form a two phase system. It was confirmed by the XRD and EDX analysis. By appropriately adjusting the x-value in the (1 − x)Mg₄Nb₂O₉-xCaTiO₃ ceramic system, near-zero τ_f value can be achieved. A new microwave dielectric material, 0.5Mg₄Nb₂O₉-0.5CaTiO₃ applicable in microwave devices is suggested and possesses the dielectric properties of a dielectric constant ?_r ∼ 24.8, a Q × f value ∼82,000 GHz (measured at 9.1 GHz) and a τ_f value ∼−0.3 ppm/°C.     

Low-temperature sintering of temperature-stable LaNbO4 microwave dielectric ceramics

We demonstrate the correlation between sintering behavior and microstructural observations in low-temperature sintered, LaNbO₄ microwave ceramics. Small CuO additions to LaNbO₄ significantly lowered the sintering temperature from 1250 to 950 °C. To elucidate the sintering mechanism, the internal microstructure of the sample manipulated by a focused ion beam (FIB) was investigated using transmission electron microscopy (TEM) and energy-dispersive spectroscopy (EDS). LaNbO₄ with 3 wt% CuO sintered at 950 °C for 2 h possessed the following excellent microwave dielectric properties: a quality factor (Qxf) of 49,000 GHz, relative dielectric constant (?_r) of 19.5, and temperature coefficient of resonant frequency (τ_f) of 1 ppm/°C. The ferroelastic phase transformation was also investigated using in situ X-ray diffraction (XRD) to explain the variation of τ_f in low-temperature sintered LaNbO₄ as a function of CuO content.     

Microwave dielectric properties of LaMgAl11O19

The suitable choice of a substrate material is one of the aims to be fulfilled in high speed microwave technology. LaMgAl₁₁O₁₉ oxide ceramic material, which belongs to the magnetoplumbite family, has been reported earlier as a potential candidate for such applications. This material has been prepared by conventional solid-state ceramic route. The structure has been studied by X-ray diffraction and characterized at microwave frequencies. The effect of dopant and glass addition on the microwave dielectric properties of this material has also been investigated. LaMgAl₁₁O₁₉ has relatively low dielectric constant (ε_r=14), low dielectric loss or high quality factor (Q_u×f>28,000 GHz at 7 GHz) and small temperature variation of resonant frequency (τ_f=−12 ppm/°C) at room temperature (300 K). These properties make LaMgAl₁₁O₁₉ as a good substrate material and as a dielectric resonator to be used in microwave devices operating at relatively high frequencies.     

Preparation, structure and dielectric properties of Ba4LaMNb3O15 (M = Ti, Sn ) ceramics

Two new cation-deficient hexagonal perovskites Ba₄LaMNb₃O₁₅ (M = Ti, Sn) ceramics were prepared by high temperature solid-state reaction route. The phase and structure of the ceramics were characterized by X-ray diffraction, scanning electron microscopy (SEM). The microwave dielectric properties of the ceramics were studied using a network analyzer. The Ba₄LaTiNb₃O₁₅ has high dielectric constant of 52, high quality factors (Q) 3500 (at 4.472 GHz), and temperature variation of resonant frequency (τ_f) +93 ppm °C⁻¹ at room temperature; Ba₄LaSnNb₃O₁₅ has dielectric constant of 39 with high Q value of 2510 (at 5.924 GHz), and τ_f −29 ppm °C⁻¹.     

Low-temperature sintering and compatibility with silver electrode of Ba4MgTi11O27 microwave dielectric ceramic

Ba₄MgTi₁₁O₂₇ microwave dielectric ceramic was investigated using X-ray diffraction, scanning electron microscopy and dielectric measurement. The pure Ba₄MgTi₁₁O₂₇ ceramic shows a high sintering temperature (∼1275 °C) and good microwave dielectric properties as Q × f of 19,630 GHz, ?_r of 36.1, τ_f of 14.6 ppm/°C. It was found that the addition of BaCu(B₂O₅) (BCB) can effectively lower the sintering temperature from 1275 to 925 °C, and does not induce much degradation of the microwave dielectric properties. The BCB-doped Ba₄MgTi₁₁O₂₇ ceramics can be compatible with Ag electrode, which makes it a promising ceramic for LTCC technology application.     

Synthesis and microwave dielectric properties of CaO-MgO-SiO2 submicron powders doped with Li2O-Bi2O3 by sol-gel method

Using Ca(NO₃)₂·4H₂O, Mg(NO₃)₂·6H₂O, Si(OC₂H₅)₄, LiNO₃ and Bi(NO₃)₃·5H₂O as raw materials, CaO-MgO-SiO₂ submicron powders were prepared at low temperature by sol-gel method. The crystallization temperature was decreased enormously by the introduction of Li-Bi liquid phase sintering aids into Ca-Mg-Si sol, and the powders with average particle sizes of 80-100 nm and 200-400 nm were obtained at the calcining temperature of 750 °C and 800 °C, respectively. The sintering characteristic and dielectric properties of powders calcined at 750 °C with different content of powders calcined at 800 °C were studied. When the content of powders calcined at 800 °C was 10 wt%, the dielectric ceramic sintered at 890 °C had compact structure, and possessed excellent microwave dielectric properties: ?_r = 7.16, Q × f = 25630 GHz, τ_f = −69.26 ppm/°C.     

Sol-gel derived CaCu3Ti4O12 ceramics: Synthesis, characterization and electrical properties

The giant dielectric constant material CaCu₃Ti₄O₁₂ (CCTO) has been synthesized by sol-gel method, for the first time, using nitrate and alkoxide precursor. The electrical properties of CCTO ceramics, showing an enormously large dielectric constant ? ∼ 60,000 (100 Hz at RT), were investigated in the temperature range from 298 to 358 K at 0, 5, 10, 20, and 40 V dc. The phases, microstructures, and impedance properties of final samples were characterized by X-ray diffraction, scanning electron microscopy, and precision impedance analyzer. The dielectric permittivity of CCTO synthesized by sol-gel method is at least three times of magnitude larger than that synthesized by other low-temperature method and solid-state reaction method. Furthermore, the results support the internal barrier layer capacitor (IBLC) model of Schottky barriers at grain boundaries between semiconducting grains.     

Effect of B2O3-Bi2O3-SiO2-ZnO glass on the sintering and microwave dielectric properties of 0.83ZnAl2O4-0.17TiO2

The 0.83ZnAl₂O₄-0.17TiO₂ (ZAT) ceramics were synthesized by solid state ceramic route. The effect of 27B₂O₃-35Bi₂O₃-6SiO₂-32ZnO (BBSZ) glass on the microwave dielectric properties of ZAT was investigated. The crystal structure and the microstructure of the ceramic-glass composites were studied by X-ray diffraction and scanning electron microscopic techniques. The low frequency dielectric loss was measured at 1 MHz. The dielectric properties of the sintered samples were measured in the microwave frequency range by the resonance method. Addition of 0.2 wt% of BBSZ improved the dielectric properties with quality factor (Q_u × f) > 120,000 GHz, temperature coefficient of resonant frequency (τ_f) = −7.3 ppm/°C and dielectric constant (?_r) = 11.7. Addition of 10 wt% of BBSZ lowered the sintering temperature to about 950 °C with Q_u × f > 10,000 GHz, ?_r = 10 and τ_f = −23 ppm/°C. The reactivity of 10 wt% BBSZ added ZAT with silver was also studied. The results show that ZAT doped with suitable amount of BBSZ glass is a possible material for low-temperature co-fired ceramic (LTCC) application.     

Microstructural evolution and dielectric properties of Cu-deficient and Cu-excess CaCu3Ti4O12 ceramics

The microstructural evolution and dielectric properties of CaCu_3−xTi₄O_12−x (3 − x = 2.8-3.05) ceramics were investigated. Normal grain growth behavior was observed at Cu/Ca ≤ 2.9, while abnormal grain growth was observed at Cu/Ca ≥ 2.95. A CuO-rich intergranular liquid phase at Cu/Ca ≥ 2.95 and angular grain morphology were the main reasons for abnormal grain growth. However, the abundant intergranular liquid at Cu/Ca = 3.05 significantly affected the relative dielectric permittivity and dielectric loss. The CuO composition is the key parameter that determines the microstructure and dielectric properties of CCTO ceramics.     

Microwave dielectric properties and microstructures of the 11Li2O-3Nb2O5-12TiO2 ceramics with B2O3 addition

The effects of B₂O₃ addition, as a sintering agent, on the sintering behavior, microstructure and microwave dielectric properties of the 11Li₂O-3Nb₂O₅-12TiO₂ (LNT) ceramics have been investigated. With the low-level doping of B₂O₃ (≤2 wt.%), the sintering temperature of the LNT ceramic could be effectively reduced to 900 °C. The B₂O₃-doped LNT ceramics are also composed of Li₂TiO₃ss and “M-phase” phases. No other phase could be observed in the 0.5-2 wt.% B₂O₃-doped ceramics sintered at 840-920 °C. The addition of B₂O₃ induced no obvious degradation in the microwave dielectric properties but increased the τ_f values. Typically, the 0.5 wt.% B₂O₃-doped ceramics sintered at 900 °C have better microwave dielectric properties of ?_r = 49.2, Q × f = 8839 GHz, τ_f = 57.6 ppm/°C, which suggest that the ceramics could be applied in multilayer microwave devices requiring low sintering temperatures.     

Structural, spectroscopic and dielectric investigations on Ba8Zn(Nb6−xSbx)O24 microwave ceramics

Ba₈Zn(Nb_6−xSb_x)O₂₄ (x = 0, 0.3, 0.6, 0.9, 1.2, 1.5, 1.8 and 2.4) ceramics were prepared through the conventional solid-state route. The materials were calcined at 1250 °C and sintered in the range 1400-1425 °C. The structure of the system was analyzed by X-ray diffraction, Fourier transform infrared and Raman spectroscopic methods. The theoretical and experimental densities were calculated. The microstructure of the sintered pellets was analyzed using scanning electron microscopy. The low frequency dielectric properties were studied in the frequency range 50 Hz-2 MHz. The dielectric constant (?_r), temperature coefficient of resonant frequency (τ_f) and the unloaded quality factor (Q_u) are measured in the microwave frequency region using cavity resonator method. The τ_f values of the samples reduced considerably with the increase in Sb concentration. The materials have intense emission lines in the visible region. The compositions have good microwave dielectric properties and photoluminescence and hence are suitable for dielectric resonator and ceramic laser applications.     

Effect of MgWO4 content on properties of Ba0.5Sr0.5TiO3 composite ceramics for tunable microwave applications

xMgWO₄-(1 − x) Ba_0.5Sr_0.5TiO₃ (x = 0.0, 5.0, 15.0, 25.0 and 35.0 wt%) composite ceramics were prepared via solid state reaction processing. Their structural and dielectric properties were systematically characterized. A significant increase in grain size was observed with increasing MgWO₄ content, which was accompanied by obvious variations in dielectric properties of the composite ceramics. It is found that the permittivity peaks of the samples gradually shifted to low temperatures with increasing MgWO₄ content. At the same time, tunabilities of the composite ceramics decreased, but their Q values increased. The sample with 35 wt% MgWO₄ possesses a high tunability of 16.8% (∼10 kHz), a low permittivity of 65 and an appropriate Q value of 309 (∼4.303 GHz), which meet the requirements of high power and impedance matching, thus making it a promising candidate for applications as electrically tunable microwave devices.     

(5 − x)BaO-xMgO-2Nb2O5 ceramics prepared using a reaction-sintering process

(5 − x)BaO-xMgO-2Nb₂O₅ (x = 0.5 and 1; 5MBN and 10MBN) microwave ceramics prepared using a reaction-sintering process were investigated. Without any calcinations involved, the mixture of BaCO₃, MgO, and Nb₂O₅ was pressed and sintered directly. MBN ceramics were produced after 2-6 h of sintering at 1350-1500 °C. The formation of (BaMg)₅Nb₄O₁₅ was a major phase in producing 5MBN ceramics, and the formation of Ba(Mg_1/3Nb_2/3)O₃ was a major phase in producing 10MBN ceramics. As CuO (1 wt%) was added, the sintering temperature dropped by more than 150 °C. We produced 5MBN ceramics with these dielectric properties: ?_r = 36.69, Qf = 20,097 GHz, and τ_f = 61.1 ppm/°C, and 10MBN ceramics with these dielectric properties: ?_r = 39.2, Qf = 43,878 GHz, and τ_f = 37.6 ppm/°C. The reaction-sintering process is a simple and effective method for producing (5 − x)BaO-xMgO-2Nb₂O₅ ceramics for applications in microwave dielectric resonators.     

Apatite phosphates containing heterovalent cations and their application in Knoevenagel condensation

Apatite structure type ortho phosphates of the formula NaLaCa₃(PO₄)₃OH and NaLaSr₃(PO₄)₃OH have been synthesized via a simple solution route. The compounds are isostructural with calcium hydroxyapatite. The phases are characterized by powder X-ray diffraction method and infrared spectroscopy. The unit cell parameters are: for NaLaCa₃(PO₄)₃OH, a = 9.457(3) and c = 6.90(1) Å and for NaLaSr₃(PO₄)₃OH, a = 9.720(3) and c = 7.23(3) Å, respectively. Knoevenagel condensation of selected aldehydes and molecules with activated methylene group is carried out using the phosphates as solid supports. Both phases facilitated the condensation reaction at room temperature in the absence of a solvent. An increase in the yield of the products is noticed when the supports are used with water.     

Processing, dielectric properties and impedance characteristics of Na0.5Bi0.5Cu3Ti4O12 ceramics

Na_0.5Bi_0.5Cu₃Ti₄O₁₂ (NBCTO) ceramics were prepared by conventional solid-state reaction method. The phase structure, microstructure and dielectric properties of NBCTO ceramics sintered at various temperatures with different soaking time were investigated. Pure NBCTO phase could be obtained with increasing the temperature and prolonging the soaking time. High dielectric permittivity (13,495) and low dielectric loss (0.031) could be obtained when the ceramics were sintered at 1000 °C for 7.5 h. The ceramics sintered at 1000 °C for 7.5 h also showed good temperature stability (−4.00 to −0.69%) over a large temperature range from −50 to 150 °C. Complex impedances results revealed that the grain was semiconducting and the grain boundaries was insulating. The grain resistance (R_g) was 12.10 Ω cm and the grain boundary resistance (R_gb) was 2.009 × 10⁵ Ω cm when the ceramics were sintered at 1000 °C for 7.5 h.     

Dielectric properties of (1−x)(Mg0.95Co0.05)TiO3-xCaTiO3 ceramic system at microwave frequency

The microwave dielectric properties and the microstructures of the (1−x)MgTiO₃-xCaTiO₃ ceramic system were investigated. With partial replacement of Mg by Co, dielectric properties of the (1−x)(Mg_0.95Co_0.05)TiO₃-xCaTiO₃ ceramics can be promoted. The microwave dielectric properties are strongly correlated with the sintering temperature. At 1275°C, the 0.95(Mg_0.95Co_0.05)TiO₃-0.05CaTiO₃ ceramics possesses excellent microwave dielectric properties: a dielectric constant ε_r of 20.3, a Q×f value of 107 000 ( at 7 GHz) and a τ_f value of −22.8 ppm/°C. By appropriately adjusting the x value in the (1−x)(Mg_0.95Co_0.05)TiO₃-xCaTiO₃ ceramic system, zero τ_f value can be achieved. With x=0.07, a dielectric constant ε_γ of 21.6, a Q×f value of 92 000 (at 7 GHz) and a τ_f value of −1.8 ppm/°C was obtained for 0.93(Mg_0.95Co_0.05)TiO₃-0.07CaTiO₃ ceramics sintered at 1275°C for 4 h.     

Low loss Sr1−xCaxLa4Ti5O17 microwave dielectric ceramics

Microwave dielectric ceramics in the Sr_1−xCa_xLa₄Ti₅O₁₇ (0 ≤ x ≤ 1) composition series were prepared through a solid state mixed oxide route. All the compositions formed single phase ceramics within the detection limit of in-house X-ray diffraction when sintered in the temperature range 1450-1580 °C. Theoretical density and molar volume decreased due to the substitution of Ca²⁺ for Sr²⁺ which was associated with a decrease in the dielectric constant (?_r) and temperature coefficient of resonant frequency (τ_f) but an increase in quality factor, Qf_o. Optimum properties were achieved for Sr_0.4Ca_0.6La₄Ti₅O₁₇ which exhibited, ?_r ∼ 53.7, Qf_o ∼ 11,532 GHz and τ_f ∼ −1.4 ppm/°C.     

Hydrothermal synthesis attempts of dawsonite-type hydroxymetalocarbonate precursor compounds for catalytic Ho, Sm, and La oxides

Chemical interactions in mixed, aqueous solutions of NH₄HCO₃ and M(NO₃)₃·9H₂O, where M stands for Ho, Sm, or La, were facilitated under various hydrothermal treatment conditions (pH 8-12 and temperature = 75-135 °C). The solution chemistry established did not make available necessary concentrations of soluble HCO₃⁻ and MO(OH)₂⁻ species for the formation of dawsonite-type ammonium hydroxymetalocarbonates, NH₄M(CO₃)(OH)₂, but, alternatively, high concentrations of soluble CO₃²⁻, and M(H₂O)_n³⁺ or M(H₂O)_n−1(OH)²⁺ facilitating, respectively, precipitation of corresponding hydrated carbonate, M₂(CO₃)₂·2H₂O, or carbonate hydroxide, MCO₃(OH). X-ray powder diffractometry, infrared spectroscopy, and thermal analyses proved alternative formation of Ho₂(CO₃)₃·2H₂O or LaCO₃(OH) under the whole set of hydrothermal treatment conditions probed, and Sm₂(CO₃)₃·2H₂O at pH < 10 or SmCO₃(OH) at pH ≥ 10, thus implying dependence of the composition of the product carbonate compound on the hydrolysability of the initial M(H₂O)_n³⁺ species and, hence, the metal ionic size (La > Sm > Ho). Calcination of the various hydrothermal treatment products at ≥600 °C resulted in the thermal genesis of the corresponding sesqui-oxides (M₂O₃). Bulk and surface characterization studies of the product oxides, employing N₂ sorptiometry and scanning electron microscopy, in addition to the above analytical techniques, revealed overall strong crystallinity, large average crystallite size, and well-defined particle morphology. They revealed, moreover, surfaces, though of limited accessibilities (≤13 m²/g), exposing OH groups of various coordination symmetries and, hence, acid-base properties, thus furnishing promising surface catalytic attributes.     

Low-temperature firing and microwave dielectric properties of ZnO-Nb2O5-TiO2-SnO2 ceramics with CuO-V2O5

The effects of CuO-V₂O₅ addition on the sintering temperature and microwave dielectric properties of ZnO-Nb₂O₅-TiO₂-SnO₂ were investigated. The CuO-V₂O₅ addition lowered the sintering temperature of ZnO-Nb₂O₅-TiO₂-SnO₂ ceramics effectively from 1150 to 860 °C due to the liquid-phase effect of Cu₂V₂O₇ and Cu₃(VO₄)₂, as observed by XRD. The microwave dielectric properties were found to strongly correlate with the sintering temperature and the amount of CuO-V₂O₅ addition. The maximum Qf values decreased with increasing CuO-V₂O₅ content, due to the formation of the second phase, Cu₃(VO₄)₂ and CuNbO₃. Zero τ_f value can be obtained by properly adjusting the sintering temperature. At 860 °C, ZnO-Nb₂O₅-TiO₂-SnO₂ ceramics with 1.5 wt.% CuO-V₂O₅ gave excellent microwave dielectric properties: ?_r = 42.3, Qf = 9000 GHz and τ_f = 8 ppm/°C.     

Improved high-Q microwave dielectric resonator using CuO-doped MgNb2O6 ceramics

The microwave dielectric properties and the microstructures of MgNb₂O₆ ceramics with CuO additions (1-4 wt.%) prepared with conventional solid-state route have been investigated. The sintered samples exhibit excellent microwave dielectric properties, which depend upon the liquid phase and the sintering temperature. It is found that MgNb₂O₆ ceramics can be sintered at 1140 °C due to the liquid phase effect of CuO addition. At 1170 °C, MgNb₂O₆ ceramics with 2 wt.% CuO addition possesses a dielectric constant (ε_r) of 19.9, a Q×f value of 110,000 (at 10 GHz) and a temperature coefficient of resonant frequency (τ_f) of −44 ppm/°C. The CuO-doped MgNb₂O₆ ceramics can find applications in microwave devices requiring low sintering temperature.