Optimal placement of reinforcement in piggyback landfill liners

The optimal placement of geogrid reinforcement in clay liners subject to differential settlement was investigated both numerically and with centrifuge modelling. Two unreinforced liners, a liner reinforced at the top-quarter depth, a liner reinforced at the bottom-quarter depth and a double reinforced liner were modelled in the centrifuge. Differential settlement was induced on the model liners by lowering a trapdoor overlain with sand. By considering: 1) the magnitude of differential settlement required to induce micro-cracks in the liners, 2) the strain fields across the liners during differential settlement and 3) the distribution of these strain fields, it was found that dividing the available reinforcement equally between the top-quarter and bottom-quarter of the liner, i.e. double reinforcement, represents the optimal reinforcement strategy.     

Static structural behavior of geogrid reinforced soil retaining walls with a deformation buffer zone

To understand the structural behavior of geogrid reinforced soil retaining walls (GRSW) with a deformation buffer zone (DBZ) under static loads, the model tests and the numerical simulations were conducted to obtain the wall face horizontal displacement, vertical and horizontal soil pressures, and geogrid strains. Results showed that compared with the common GRSW, the horizontal displacement of GRSW with DBZ decreased, and the horizontal soil pressure acting on the face panel of GRSW with DBZ increased. The vertical and horizontal soil pressures showed a nonlinear distribution along the reinforcement length, and the value was smaller near the face panel. The horizontal soil pressure acting on the face panel of GRSW with DBZ was greater than that of the common GRSW in the middle portion. The cumulative strain of the geogrid had a single-peak distribution along its length; the maximum strain of the geogrid was 0.45%, the maximum tension was approximately 29.12% of ultimate tensile strength.     

Behaviour of geogrid reinforced soil retaining wall with concrete-rigid facing

Monitoring was carried out during construction of a cast-in-situ concrete-rigid facing geogrid reinforced soil retaining wall in the Gan (Zhou)-Long (Yan) railway main line of China. The monitoring included the vertical foundation pressure and lateral earth pressure of the reinforced soil wall facing, the tensile strain in the reinforcement and the horizontal deformation of the facing. The vertical foundation pressure of reinforced soil retaining wall is non-linear along the reinforcement length, and the maximum value is at the middle of the reinforcement length, moreover the value reduces gradually at top and bottom. The measured lateral earth pressure within the reinforced soil wall is non-linear along the height and the value is less than the active lateral earth pressure. The distribution of tensile strain in the geogrid reinforcements within the upper portion of the wall is single-peak value, but the distribution of tensile strain in the reinforcements within the lower portion of the wall has double-peak values. The potential failure plane within the upper portion of the wall is similar to “0.3H method”, whereas the potential failure plane within portion of the lower wall is closer to the active Rankine earth pressure theory. The position of the maximum lateral displacement of the wall face during construction is within portion of the lower wall, moreover the position of the maximum lateral displacement of the wall face post-construction is within the portion of the top wall. These monitoring results of the behaviour of the wall can be used as a reference for future study and design of geogrid reinforced soil retaining wall systems.     

Analytical modeling of geogrid reinforced soil foundation

This paper aims at developing analytical solutions for estimating the ultimate bearing capacity of geogrid reinforced soil foundations (RSF) for both sand and silty clay soils. Failure mechanisms for reinforced soil foundations are proposed based on the literature review and the results of experimental study on model footing tests conducted by the authors. New bearing capacity formulas that incorporate the contribution of reinforcements to the increase in bearing capacity are then developed for both reinforced sand and silty clay soil foundations based on the proposed failure mechanisms. The predicted bearing capacity values are compared with the results of laboratory model tests on reinforced sand and silty clay soil. The proposed analytical solutions were also verified by the results of large-scale model tests conducted by the authors for reinforced silty clay and the data reported in the literature. The predicted bearing capacity values from analytical solutions are in good agreement with the test results.     

Effects of prestressing the reinforcement on the behavior of reinforced granular beds overlying weak soil

The effects of prestressing the reinforcement on the strength improvement and settlement reduction of a reinforced granular bed overlying weak soil are being investigated through a series of laboratory scale bearing capacity tests. The influences of parameters such as strength of underlying weak soil, thickness of granular bed, magnitude of prestressing force, direction of prestressing forces and number of layers of reinforcement are being examined. Finite element analyses are carried out using the FE program PLAXIS to study the effect of prestressing the reinforcement. Results obtained from finite element analyses are found to be in reasonably good agreement with the experimental results.     

DIA of centrifuge model tests on geogrid reinforced soil walls with low-permeable backfills subjected to rainfall

Geogrid reinforced soil walls (GRSWs) constructed using low-permeable backfills often experience failures when subjected to rainfall. The objective of this paper is to employ centrifuge modelling to investigate the effect of geogrid types on the performance of GRSW models constructed with low-permeable backfill, when subjected to rainfall intensity of 10 mm/h. A 4.5 m radius large beam centrifuge facility was used, and rainfall was simulated using a custom-designed rainfall simulator at 40 gravities. Digital Image Analysis (DIA) was employed to understand the deformation behaviour of GRSWs with low stiffness geogrid layers with and without drainage provision subjected to rainfall. Additionally, the effect of varying stiffness of geogrid reinforcement layers across the height of GRSW was also investigated. The interpretation of DIA helped to quantify displacement vector fields, face movements, surface settlement profiles and geogrid strain distribution with depth. Irrespective of drainage provision, GRSWs reinforced with low stiffness geogrid layers experienced a catastrophic failure at the onset of rainfall. However, GRSW reinforced with geogrid layers of varying stiffness was observed to perform well. This study demonstrates the effective use of DIA of GRSWs subjected to rainfall along with centrifuge-based physical model testing.     

Upper bound estimate of scaled reinforced soil retaining walls

A kinematic approach based on the framework of limit analysis is applied for stability analysis of model reinforced vertical and sloping walls with cohesive backfill that were brought to failure under self-weight in a geotechnical centrifuge. A rotational failure mechanism is used to compute critical heights of the unreinforced and reinforced models; and the Constrained Simplex method is employed in the optimization scheme. The prototype equivalent heights predicted by the analyses are within the distress range; i.e., development of tension crack and collapse of the retaining walls occurred during centrifuge tests.     

Centrifuge model studies on the performance of soil walls reinforced with sand-cushioned geogrid layers

This paper is to investigate the effectiveness of encapsulating geogrid layers within thin sand layers, for enhancing the deformation behavior of vertical reinforced soil walls constructed with marginal backfills. Centrifuge model tests were performed on vertical soil walls, reinforced with geogrid layers, using a 4.5 m radius large beam centrifuge available at IIT Bombay at 40 gravities. The backfill conditions, height of soil wall, reinforcement length, and reinforcement spacing, were kept constant in all the tests. A wrap-around technique was used to represent flexible facing. Three different geogrid types with varying stiffness were used in the present study. The walls were instrumented with vertical linear variable differential transformers to monitor surface settlements during the tests. Marker-based digital image analysis technique was used to determine face movements and distribution of geogrid strain along the wall height. The deformation behavior of soil walls, reinforced with geogrid layers encapsulated in thin layers of sand, were compared against a base model having no sand-cushioned geogrid layers. Provision of sand-cushioned geogrid layers and increase in geogrid stiffness were found to limit normalized face movements (S_f/H), normalized crest settlements (S_c/H), and change in maximum peak reinforcement strain (dε_pmax). Sand-cushioned geogrid layers were also found to limit the development of tension cracks behind and within the reinforced zone. Significant reduction in rate of maximum face movement (dS_fmax/dt) and rate of maximum peak reinforcement strain (dε_pmax/dt) was observed, with an increase in value of normalized reinforcement stiffness (J_g/γH²) of geogrid layers. The analysis and interpretation of centrifuge model tests on soil walls, constructed with marginal backfills and reinforced with sand-cushioned geogrid layers, indicate that their performance is superior to the walls without sand-cushioned geogrid layers.     

Failure behavior and mechanism of slopes reinforced using soil nail wall under various loading conditions

Soil–nailing technology is widely applied in practice for reinforcing slopes. A series of centrifuge model tests was conducted on slopes reinforced with a soil nail wall under three types of loading conditions. The behavior and mechanism of failure process of the reinforced slopes were studied using image-based observation and displacement measurements for the slope, nails, and cement layer. The nailing significantly increased the stability level and restricted the tension cracks of the slopes. Increasing the nail length improved the stability of the reinforced slopes with deeper slip surfaces. The reinforced slope exhibited a significant failure process, in which slope slippage failure and cement layer fracture occurred in conjunction with a coupling effect. The deformation localization was induced by the loading within the slope and ultimately developed into a slip surface. The nailing reinforced the slope by significantly delaying the occurrence of the deformation localization within the slope. The failure of nails was recognized as a combination of pull-out failure and bend deformation. The loading conditions were shown to have a significant effect on slope deformation and nail deflection, and they consequently influenced the failure behavior and its formation sequence.     

Centrifuge and numerical model studies on the behaviour of geogrid reinforced soil walls with marginal backfills with and without geocomposite layers

The aim of this paper is to study the effect of geocomposite layers as internal drainage system on the behaviour of geogrid reinforced soil walls with marginal backfills using centrifuge and numerical modelling. A series of centrifuge model tests were carried out using a 4.5 m radius beam centrifuge facility available at IIT Bombay. A seepage condition was imposed to all models to simulate rising ground water condition. Displacement and pore water pressure transducers were used to monitor the performance of all centrifuge models. A geogrid reinforced soil wall without any geocomposite layer experienced catastrophic failure soon after applying seepage due to the development of excess pore water pressure within the reinforced soil zone of the wall. In comparison, reinforced soil wall with two geocomposite layers at the bottom portion of the wall was found to have a good performance at the onset of seepage and by embedding four geocomposite layers up to the mid-height of the wall from bottom as a result of lowering phreatic surface much more effectively. For analysing further the observed behaviour of centrifuge model tests, stability and seepage analysis were conducted using SLOPE/W and SEEP/W software packages. A good agreement was found between the results of numerical analysis and observation made in centrifuge tests. The effect of number of geocomposite layers as well as its transmissivity was further analysed using parametric study. The results of parametric study revealed that the number of geocomposite layers plays a main role on the good performance of the geogrid reinforced soil walls with marginal backfill.     

Experimental investigation on the accumulated strain of coarse-grained soil reinforced by geogrid under high-cycle cyclic loading

In this study, a series of cyclic triaxial tests were conducted to study the accumulated strain of coarse-grained soil reinforced with geogrids, and the effect of the number of geogrid layers, confining pressure and cyclic stress amplitude was investigated in detail. The test results show that the final accumulated axial strain of the soils reinforced with geogrids is less than that without reinforcement, and less accumulated axial strain is generated for the specimens with more geogrid layers under identical cyclic loading. The results also show that a higher confining pressure or a lower cyclic stress amplitude yields less accumulated axial strain for the reinforced soils. Furthermore, the plastic shakedown limits are determined by the criterion proposed by Chen et al. It indicates that the plastic shakedown limit increases significantly when one layer of geogrid is incorporated into the specimen and then tends to level off with a continuous increase in the number of geogrid layers. Moreover, a higher confining pressure yields a higher plastic shakedown limit for the soils reinforced with geogrid. The results demonstrated that the use of geogrid can be an effective method to reduce the accumulated deformation of subgrade filling materials under high-cycle traffic loading.     

Three-dimensional physical modeling of load transfer in basal reinforced embankments under differential settlement

This study developed a large-scale laboratory apparatus to evaluate the load transfer behavior of basal reinforced embankment fill because of soil arching and geogrid tensile force. A 3D trapdoor-like test system performed five scaled model tests using analogical soil. The instrumentation system involved multiple earth pressure cells, dial gauges, multipoint settlement gauges, and geogrid strainmeters. Comprehensive measurements were performed to investigate the evolution of soil stress and displacement at specific fill elevations with variations in the area replacement ratio and geogrid stiffness. The critical height of the soil arching was determined to be ～1.1–1.94 times the clear pile spacing based on the soil stress and displacement profiles. The distribution of the geogrid tensile strain between and above the adjacent caps demonstrated that the maximum geogrid strains occur on top of the caps, and the tensioned geogrid effect on the load transfer efficiency was evaluated. The cap size and center-to-center pile spacing affect the pile efficacy more significantly than the stiffness of the geogrid. The measured critical heights of arching, stress concentration ratios, and geogrid strain matched those calculated by several well-recognized analytical methods. This experimental program facilitates the development of arching models that account for differential settlement impact.     

Deformation behavior of clay cap barriers of hazardous waste containment systems: Full-scale and centrifuge tests

The objective of this paper is to study the deformation behavior of a clay cap barrier of waste containment system for storing hazardous waste. The risk of bending of a clay barrier in case of differential settlements within underlying waste is focused in the present study. Field bending “bursting tests” were performed in France on clay barriers of 0.7 m thickness at different water contents. An attempt has been made to determine limiting distortion level at which cracks are initiated. The cap clay barrier configuration tested through field bursting tests was simulated at 12.5 g in a geo-centrifuge on model cap clay barriers of 56 mm thickness subjected to bursting mode of failure. Digital image analysis technique was used to ascertain initiation and propagation of cracking at the onset of differential settlements. Further influence of discrete and randomly distributed polypropylene tape fibers in restraining cracking tendency of the clay barrier was evaluated through a centrifuge model test. With an increase in the molding water content and the presence of randomly distributed fibers, an increase in limiting distortion level was observed. Use of 0.5% of fiber dosage and 90 mm long discrete fibers was found to restrain propagation of cracking of a clay barrier subjected to differential movements. Analysis and interpretation of field bursting tests was found to be in good agreement with physically observed centrifuge model test results.     

Centrifuge model tests on the behavior of strip footing on geotextile-reinforced slopes

This paper examines the stability of geotextile-reinforced slopes when subjected to a vertical load applied to a strip footing positioned close to the slope crest. Vertical spacing between geotextile reinforcement was varied while maintaining a constant slope angle, load position, soil density and geotextile type. Small-scale physical tests were conducted using a large beam centrifuge to simulate field prototype conditions. After the model was accelerated to 40g, a load was applied to the strip footing until slope failure occurred. Digital image analysis was performed, using photographs taken in-flight, to obtain slope displacements and strain distribution along the reinforcement layers at different loading pressures during the test and at failure. Stability analysis was also conducted and compared with centrifuge model test results. The vertical spacing between reinforcement layers has a significant impact on the stability of a reinforced slope when subjected to a vertical load. Less vertical distance between reinforcement layers allows the slope to tolerate much greater loads than layers spaced further apart. Distributions of peak strains in reinforcement layers due to the strip footing placed on the surface of the reinforced slope were found to extend up to mid-height of the slope and thereafter they were found to be negligible. Stability analysis of the centrifuge models was found to be consistent with the observed performance of geotextile-reinforced slopes subjected to loading applied to a strip footing near the crest.     

Centrifuge modeling of geotextile-reinforced slopes subjected to differential settlements

Today, geosynthetic-reinforced soil structures are widely used to support bridge abutments and approach roads in place of traditional pile supports and techniques. In such situations, foundation conditions have been shown to adversely affect the stability and deformation behaviour of overlying geosynthetic-reinforced slopes and walls. This paper addresses the response of geotextile-reinforced slopes subjected to differential settlements in a geotechnical centrifuge. Centrifuge model tests were carried out on model geotextile-reinforced sand slopes with two different types of reinforcement. A wrap-around technique was used to represent a flexible facing. In order to initiate failure in the reinforcement layers, the ratio of length of reinforcement to height of the slope was maintained as 0.85. One of the objectives of this paper is to present about a special device developed for inducing differential settlements during centrifuge test at 40g for a reinforced soil structure. A digital image analysis technique was employed to arrive at displacement vectors of markers glued to the reinforcement layers. The displacements were used to compute and analyze the strain distribution along the reinforcement layers during different settlement stages. Results of the centrifuge test indicate that even after inducing a differential settlement equivalent to 1.0 m in prototype dimensions, the geotextile-reinforced soil structure with a flexible facing was not found to experience a collapse failure. Analysis of geotextile strain results shows that the location of the maximum peak reinforcement strain occurs along the bottom-most reinforcement layer at the onset of differential settlements, at the point directly below the crest of the slope.     

Degradation of C2-C15 volatile organic compounds in a landfill cover soil

The composition of non-methane volatile organic compounds (hereafter VOCs) in i) the cover soil, at depths of 30, 50 and 70 cm, and ii) gas recovery wells from Case Passerini landfill site, (Florence, Italy) was determined by GC-MS. The study, based on the analysis of interstitial gases sampled along vertical profiles within the cover soil, was aimed to investigate the VOC behaviour as biogas transits from a reducing to a relatively more oxidizing environment. A total of 48 and 63 different VOCs were identified in the soil and well gases, respectively. Aromatics represent the dominant group (71.5% of total VOC) in soil gases, followed by alkanes (6.8%), ketones (5.7%), organic acids (5.2%), aldehydes (3.0%), esters (2.6%), halogenated compounds (2.1%) and terpenes (1.3%). Cyclics, heterocyclics, S-bearing compounds and phenols are ≤ 1%. In the wells the VOC composition is characterized by higher concentrations of cyclic (7.6%) and S-bearing compounds (2%) and lower concentrations of O-bearing compounds. The vertical distribution of VOCs in the cover soil shows significant variations: alkanes, aromatics and cyclics decrease at decreasing depth, whereas an inverse trend is displayed by the O-bearing species. Total VOC and CH₄ concentrations at a depth of 30 cm in the soil are comparable, inferring that microbial activity is likely affecting VOCs at a very minor extent with respect to CH₄. According to these considerations, to assess the biogas emission impact, usually carried out on the sole basis of CO₂ and CH₄ emission rates, the physical-chemical behaviour of VOCs in the cover soil, regulating the discharge of these highly contaminant compounds in ambient air, has to be taken into account. The soil vertical distribution of these species can be used to better evaluate the efficiency of oxidative capability of intermediate and final covers.     

Bearing capacity and failure mechanism of reinforced foundations based on rigid-plastic finite element formulation

A series of model loading tests on both unreinforced and reinforced foundations have been carried out, and in these tests the ground was modeled by aluminum rods. A rigid-plastic finite element analysis considering the effect of geometrical nonlinearity has been conducted to quantitatively investigate both the increase of calculated bearing capacity and the progress in deformation localization corresponding to the settlement of a loading plate. In the analysis, the reinforcing material and the surrounding soil were modeled as a composite material. Based on the comparative study between the test results and the numerical analysis, it is concluded that the proposed numerical method is capable of investigating quantitatively not only the bearing capacity but also the failure mechanism. In addition, the effectiveness of the proposed numerical analysis has been confirmed.