Remarkable improvement of NOx–PM trade-off in a diesel engine by means of bioethanol and EGR

In order to realize a premixed compression ignition (PCI) engine, the effects of bioethanol–gas oil blends and exhaust gas recirculation (EGR) on PM–NO_x trade-off have been investigated focusing on ignition delay, premixed combustion, diffusion combustion, smoke, NO_x and thermal efficiency. The present experiment was done by increasing the ethanol blend ratio and ethanol and by increasing the EGR ratio in a single cylinder direct injection diesel engine. It is found that a remarkable improvement in PM–NO_x trade-off can be achieved by promoting the premixing based on the ethanol blend fuel having low evaporation temperature, large latent heat and low cetane number as well, in addition, based on a marked elongation of ignition delay due to the low cetane number fuel and the low oxygen intake charge. As a result, very low levels of NO_x and PM, which satisfies the 2009 emission standards imposed on heavy duty diesel engines in Japan, were achieved without deterioration of brake thermal efficiency in the PCI engine fuelled with the 50% ethanol blend diesel fuel and the high EGR ratio. It is noticed that smoke can be reduced even by increasing the EGR ratio under the highly premixed condition.     

Influence of high rates of supplemental cooled EGR on NOx and PM emissions of an automotive HSDI diesel engine using an LP EGR loop

Previous experimental studies on diesel engine have demonstrated the potential of exhaust gas recirculation (EGR) as an in‐cylinder NO_x control method. Although an increase in EGR at constant boost pressure (substitution EGR) is accompanied with an increase in particulate matter (PM) emissions in the conventional diesel high‐temperature combustion (HTC), the recirculation of exhaust gases supplementary to air inlet gas (supplemental EGR) by increasing the boost pressure has been suggested as a way to reduce NO_x emissions while limiting the negative impact of EGR on PM emissions. In the present work, a low‐pressure (LP) EGR loop is implemented on a standard 2.0 l automotive high‐speed direct injection (HSDI) turbocharged diesel engine to study the influence of high rates of supplemental cooled EGR on NO_x and PM emissions. Contrary to initial high‐pressure (HP) EGR loop, the gas flow through the turbine is unchanged while varying the EGR rate. Thus, by closing the variable geometry turbine (VGT) vanes, higher boost pressure can be reached, allowing the use of high rates of supplemental EGR. Furthermore, recirculated exhaust gases are cooled under 50°C and water vapour is condensed and taken off from the recirculated gases. An increase in the boost pressure at a given inlet temperature and dilution ratio (DR) results in most cases an increase in NO_x emissions and a decrease in PM emissions. The result of NO_x–PM trade‐off, while varying the EGR rate at fixed inlet temperature and boost pressure depends on the operating point: it deteriorates at low load conditions, but improves at higher loads. Further improvement can be obtained by increasing the injection pressure. A decrease by approximately 50% of NO_x emissions while maintaining PM emission level, and brake specific fuel consumption can be obtained with supplemental cooled EGR owing to an LP EGR loop, compared with the initial engine configuration (HP moderately cooled EGR). Copyright © 2008 John Wiley & Sons, Ltd.     

Engine performance and emissions of a diesel engine operating on diesel-RME (rapeseed methyl ester) blends with EGR (exhaust gas recirculation)

The effects of biodiesel (rapeseed methyl ester, RME) and different diesel/RME blends on the diesel engine NO_x emissions, smoke, fuel consumption, engine efficiency, cylinder pressure and net heat release rate are analysed and presented. The combustion of RME as pure fuel or blended with diesel in an unmodified engine results in advanced combustion, reduced ignition delay and increased heat release rate in the initial uncontrolled premixed combustion phase. The increased in-cylinder pressure and temperature lead to increased NO_x emissions while the more advanced combustion assists in the reduction of smoke compared to pure diesel combustion. The lower calorific value of RME results in increased fuel consumption but the engine thermal efficiency is not affected significantly. When similar percentages (% by volume) of exhaust gas recirculation (EGR) are used in the cases of diesel and RME, NO_x emissions are reduced to similar values, but the smoke emissions are significantly lower in the case of RME. The retardation of the injection timing in the case of pure RME and 50/50 (by volume) blend with diesel results in further reduction of NO_x at a cost of small increases of smoke and fuel consumption.     

H2 effects on diesel combustion and emissions with an LPL-EGR system

In this study, we examined H₂ effects on the combustion and emissions of a diesel engine with low-pressure loop (LPL) exhaust gas recirculation (EGR). We converted a 2.2-L four-cylinder direct-injection diesel engine satisfying Euro5 for H₂ supply. An LPL-EGR system replaced the high-pressure loop (HPL) EGR system. For all tests, the brake mean effective pressure (BMEP) was kept at 4 bar and the EGR ratio was varied from 9 to 42%. The H₂ energy percentage was varied from 0 to 7.4% independently to evaluate the H₂ effects and EGR effects separately. The heat release rate was calculated from the measured cylinder pressure. We found that substitution of H₂ for diesel fuel made the premixed burn fraction larger, and reduced the nitrous oxide (NOx) and particulate matter (PM) emissions simultaneously. For example, the NOx emissions were reduced by 36% for an EGR of 42% and an H₂ percentage of 7.4%. PM emissions were reduced by 18% for an EGR of 35% and an H₂ percentage of 7.4% compared with diesel fuel only cases.     

Experimental study of the performances of a modified diesel engine operating in homogeneous charge compression ignition (HCCI) combustion mode versus the original diesel combustion mode

Homogeneous charge compression ignition (HCCI) combustion mode provides very low NO_x and soot emissions; however, it has some challenges associated with hydrocarbon (HC) emissions, fuel consumption, difficult control of start of ignition and bad behaviour to high loads. Cooled exhaust gas recirculation (EGR) is a common way to control in-cylinder NO_x production in diesel and HCCI combustion mode. However EGR has different effects on combustion and emissions, which are difficult to distinguish. This work is intended to characterize an engine that has been modified from the base diesel engine (FL1 906 DEUTZ-DITER) to work in HCCI combustion mode. It shows the experimental results for the modified diesel engine in HCCI combustion mode fueled with commercial diesel fuel compared to the diesel engine mode. An experimental installation, in conjunction with systematic tests to determine the optimum crank angle of fuel injection, has been used to measure the evolution of the cylinder pressure and to get an estimate of the heat release rate from a single-zone numerical model. From these the angle of start of combustion has been obtained. The performances and emissions of HC, CO and the huge reduction of NO_x and smoke emissions of the engine are presented. These results have allowed a deeper analysis of the effects of external EGR on the HCCI operation mode, on some engine design parameters and also on NO_x emission reduction.     

Investigation of the effects of hydrogen on cylinder pressure in a split-injection diesel engine at heavy EGR

The distinctive properties of hydrogen have initiated considerable applied research related to the internal combustion engine. Recently, it has been reported that NO_x emissions were reduced by using hydrogen in a diesel engine at low temperature and heavy EGR conditions. As the continuing study, cylinder pressure was also investigated to determine the combustion characteristics and their relationship to NO_x emissions. The test engine was operated at constant speed and fixed diesel fuel injection rate (1500 rpm, 2.5 kg/h). Diesel fuel was injected in a split pattern into a 2-L diesel engine. The cylinder pressure was measured for different hydrogen flow rates and EGR ratios. The intake manifold temperature was controlled to be the same to avoid the gas intake temperature variations under the widely differing levels (2%-31%) of EGR. The measured cylinder pressure was analyzed for characteristic combustion values, such as mass burn fraction and combustion duration.The rising crank angle of the heat release rate was unaffected by the presence of hydrogen. However, supplying hydrogen extended the main combustion duration. This longer main combustion duration was particularly noticeable at the heavy EGR condition. It correlated well with the reduced NO_x emissions.     

Effects of Fischer-Tropsch diesel fuel on combustion and emissions of direct injection diesel engine

Effects of Fischer-Tropsch (F-T) diesel fuel on the combustion and emission characteristics of a single-cylinder direct injection diesel engine under different fuel delivery advance angles were investigated. The experimental results show that F-T diesel fuel exhibits shorter ignition delay, lower peak values of premixed burning rate, lower combustion pressure and pressure rise rate, and higher peak value of diffusion burning rate than conventional diesel fuel when the engine remains unmodified. In addition, the unmodified engine with F-T diesel fuel has lower brake specific fuel consumption and higher effective thermal efficiency, and presents lower HC, CO, NO _x and smoke emissions than conventional diesel fuel. When fuel delivery advance angle is retarded by 3 crank angle degrees, the combustion duration is obviously shortened; the peak values of premixed burning rate, the combustion pressure and pressure rise rate are further reduced; and the peak value of diffusion burning rate is further increased for F-T diesel fuel operation. Moreover, the retardation of fuel delivery advance angle results in a further significant reduction in NO _x emissions with no penalty on specific fuel consumption and with much less penalty on HC, CO and smoke emissions. __________ Translated from Chinese Internal Combustion Engine Engineering, 2007, 28(2): 19–23 [译自: 内燃机工程]     

Experimental investigation of control of NOx emissions in biodiesel-fueled compression ignition engine

Biodiesel is an alternative fuel consisting of the alkyl esters of fatty acids from vegetable oils or animal fats. Vegetable oils are produced from numerous oil seed crops (edible and non-edible), e.g., rapeseed oil, linseed oil, rice bran oil, soybean oil, etc. Research has shown that biodiesel-fueled engines produce less carbon monoxide (CO), unburned hydrocarbon (HC), and particulate emissions compared to mineral diesel fuel but higher NO_x emissions. Exhaust gas recirculation (EGR) is effective to reduce NO_x from diesel engines because it lowers the flame temperature and the oxygen concentration in the combustion chamber. However, EGR results in higher particulate matter (PM) emissions. Thus, the drawback of higher NO_x emissions while using biodiesel may be overcome by employing EGR. The objective of current research work is to investigate the usage of biodiesel and EGR simultaneously in order to reduce the emissions of all regulated pollutants from diesel engines. A two-cylinder, air-cooled, constant speed direct injection diesel engine was used for experiments. HCs, NO_x, CO, and opacity of the exhaust gas were measured to estimate the emissions. Various engine performance parameters such as thermal efficiency, brake specific fuel consumption (BSFC), and brake specific energy consumption (BSEC), etc. were calculated from the acquired data. Application of EGR with biodiesel blends resulted in reductions in NO_x emissions without any significant penalty in PM emissions or BSEC.     

Study of low emission homogeneous charge compression ignition (HCCI) engine using combined internal and external exhaust gas recirculation (EGR)

This paper focuses on the effects of internal and cooled external exhaust gas recirculation (EGR) on the combustion and emission performance of diesel fuel homogeneous charge compression ignition (HCCI). The use of fuel injection before the top center (TC) of an exhaust stroke and the negative valve overlap (NVO) to form the homogeneous mixture achieves low NO_x and smoke emissions HCCI. Internal and external EGR are combined to control the combustion. Internal exhaust gas recirculation (IEGR) benefits to form a homogeneous mixture and reduces smoke emission further, but lower the high load limits of HCCI. Cooled external EGR can delay the start of combustion (SOC) effectively, which is very useful for high cetane fuel (diesel) HCCI because these fuels can easily self-ignited, making the SOC earlier. External EGR can avoid the knock combustion of HCCI at high load, which means it can expand the high load limit. HCCI maintains low smoke emission at various EGR rates and various loads compared with a conventional diesel engine because there are no fuel-rich volumes in the cylinder.     

Combining GTL fuel,reformed EGR and HC-SCR aftertreatment system to reduce diesel NOx emissions. A statistical approach

An ultra-low sulphur diesel (ULSD) fuel and a synthetic gas-to-liquid (GTL) fuel, besides different types of standard and reformed EGR, were evaluated in a single-cylinder, direct injection, diesel engine equipped with hydrocarbon-selective catalytic reduction (HC-SCR) aftertreatment system. The results obtained were statistically analysed (at 95% statistical significance) to identify the most significant factors that affect NO_x emissions and to search for the optimum operation conditions in order to minimize these emissions. For that purpose, a fully crossed factorial experimental design was used, including two different engine speeds (1200 and 1500 rpm), two engine loads (25% and 50%), and four EGR/REGR ratios (0%, 10%, 20% and 30%) resulting in almost one hundred tests. An optimal combination of fuel type, REGR type and REGR ratio was proved to reduce around 89–95% of the reference NO_x emissions. In general, at 25% engine load GTL fuelling combined with the reformed EGR with the highest hydrogen content was found the most desirable, as the hydrogen sharply increased the NO_x conversion in the SCR catalyst. Differently, at 50% load standard EGR was sufficient to reach high NO_x reductions. These findings may be used for the implementation of a system on-board capable to switch from EGR to REGR, which will help engine manufacturers to meet the future emission regulations.     

An experimental investigation on performance and emissions study with port injection using diesel as an ignition source for different EGR flow rates

Exhaust gas recirculation, EGR, is one of the most effective means of reducing NO_x emissions from IC engines and is widely used in order to meet the emission standards. In the present work, experimental investigation has been carried out to study the NO_x reduction characteristics by exhaust gas recirculation in a dual fueled engine using hydrogen and diesel. A single cylinder diesel engine was converted to operate on hydrogen-diesel dual fuel mode. Hydrogen was injected in intake port and diesel was injected directly inside the cylinder. The injection timing and injection duration of hydrogen were optimized initially based on the performance and emissions. It was observed that start of injection at 5° before gas exchange top dead center (BGTDC) and injection duration of 30° crank angle gives the best results. The flow rate of hydrogen was optimized as 7.5 lpm for the best start of injection and injection duration of hydrogen. Cold exhaust gas recirculation technique was adopted for the optimized injection parameter of hydrogen and flow rate. Maximum quantity of exhaust gases recycled during the test was 25% beyond this the combustion was not stable resulting in increase in smoke.     

Methods for in-cylinder EGR stratification and its effects on combustion and emission characteristics in a diesel engine

The effects of in-cylinder EGR stratification on combustion and emission characteristics are investigated in a single cylinder direct injection diesel engine. To achieve in-cylinder EGR stratification, external EGR rates of two intake ports are varied by supplying EGR asymmetrically using a separated intake runner. The EGR stratification pattern is improved using a 2-step bowl piston and an offset chamfer at the tangential intake port. When high EGR gas is supplied to the left (tangential) port, a high EGR region is formed at the central upper region of the combustion chamber. Consequently, combustion is initiated in the low EGR region, and PM is reduced significantly. When high EGR gas is supplied to the right (helical) port, a high EGR region is formed at the lower periphery of the combustion chamber. Therefore, combustion is initiated in the high EGR region, and NO_x is reduced without PM penalty. Stratified EGR potentially reduces NO_x by maximum 45%, without penalties of performance and other emissions. A proper in-cylinder swirl with stratified EGR maximizes the effects and achieves simultaneous reduction of NO_x by 7% and PM by 23%. Moreover, the robustness of stratified EGR is evaluated under various operating conditions and injection strategies.     

Combustion performance and emission reduction characteristics of automotive DME engine system

This article is a condensed overview of a dimethyl ether (DME) fuel application for a compression ignition diesel engine. In this review article, the spray, atomization, combustion and exhaust emissions characteristics from a DME-fueled engine are described, as well as the fundamental fuel properties including the vapor pressure, kinematic viscosity, cetane number, and the bulk modulus. DME fuel exists as gas phase at atmospheric state and it must be pressurized to supply the liquid DME to fuel injection system. In addition, DME-fueled engine needs the modification of fuel supply and injection system because the low viscosity of DME caused the leakage. Different fuel properties such as low density, viscosity and higher vapor pressure compared to diesel fuel induced the shorter spray tip penetration, wider cone angle, and smaller droplet size than diesel fuel. The ignition of DME fuel in combustion chamber starts in advance compared to diesel or biodiesel fueled compression ignition engine due to higher cetane number than diesel and biodiesel fuels. In addition, DME combustion is soot-free since it has no carbon–carbon bonds, and has lower HC and CO emissions than that of diesel combustion. The NO_x emission from DME-fueled combustion can be reduced by the application of EGR (exhaust gas recirculation). This article also describes various technologies to reduce NO_x emission from DME-fueled engines, such as the multiple injection strategy and premixed combustion. Finally, the development trends of DME-fueled vehicle are described with various experimental results and discussion for fuel properties, spray atomization characteristics, combustion performance, and exhaust emissions characteristics of DME fuel.     

Development of variable timing fuel injection cam for effective abatement of diesel engine emissions

Fossil fuel run diesel engines are being favored in light, medium and heavy duty applications as they exhibit higher fuel conversion efficiencies. Direct injection diesels are still facing challenges to obtain trade-off between oxides of nitrogen and particulate emissions. There are sophisticated strategies such as common rail direct injection, particulate filters with associated sensors and actuators but limited to expensive comfort vehicles. In the present experimental study, a mechanically operated simple component, variable timing fuel injection cam, is designed for a 510 cc automotive type naturally aspirated, water-cooled, direct injection diesel engine. Modifications in the fuel injection cam and gear train are carried out to suit the existing engine configuration. Variable speed tests are carried out for testing the efficacy of component on both engine and chassis dynamometers for performance and emissions. It is observed that the engine which is already retarded could further be retarded with variable timing fuel injection cam. Significant reductions in NO_x and smoke emission levels are achieved. Combined effect of VIC with 7% EGR could reduce CO by about 88%, HC + NO_x by 37% and PM emissions by 90%. The Engine incorporated with the designed component and EGR, successfully satisfied the existing emission norms with improved power and specific fuel consumption.     

Performance, emissions and heat release characteristics of direct injection diesel engine operating on diesel oil emulsion

Emulsions of diesel and water are often promoted as being able to overcome the difficulty of simultaneously reducing emissions of both oxidises of nitrogen (NO_x) and particulate matter from diesel engines. In this paper we present measurements of the performance and NO_x and hydrocarbon emissions of a diesel engine operating on a typical diesel oil emulsion and examine through the use of heat release analysis differences found during its combustion relative to standard diesel in the same engine. While producing similar or greater thermal efficiency and improved NO_x and hydrocarbon emission outcomes, use of the emulsion also results in an increase in brake specific fuel consumption. Use of the emulsion is also shown to result in a retarded fuel injection, but smaller ignition delay for the same engine timing. As a result of these changes, cylinder pressures and temperatures are lower.     

An experimental investigation on hydrogen as a dual fuel for diesel engine system with exhaust gas recirculation technique

With higher rate of depletion of the non-renewable fuels, the quest for an appropriate alternative fuel has gathered great momentum. Though diesel engines are the most trusted power sources in the transportation industry, due to stringent emission norms and rapid depletion of petroleum resources there has been a continuous effort to use alternative fuels. Hydrogen is one of the best alternatives for conventional fuels. Hydrogen has its own benefits and limitations in its use as a conventional fuel in automotive engine system.In the present investigation, hydrogen-enriched air is used as intake charge in a diesel engine adopting exhaust gas recirculation (EGR) technique with hydrogen flow rate at 20 l/min. Experiments are conducted in a single-cylinder, four-stroke, water-cooled, direct-injection diesel engine coupled to an electrical generator. Performance parameters such as specific energy consumption, brake thermal efficiency are determined and emissions such as oxides of nitrogen, hydrocarbon, carbon monoxide, particulate matter, smoke and exhaust gas temperature are measured. Usage of hydrogen in dual fuel mode with EGR technique results in lowered smoke level, particulate and NO_x emissions.     

Effect of Exhaust Gas Recirculation (EGR) on performance,emissions, deposits and durability of a constant speed compression ignition engine

To meet stringent vehicular exhaust emission norms worldwide, several exhaust pre-treatment and post-treatment techniques have been employed in modern engines. Exhaust Gas Recirculation (EGR) is a pre-treatment technique, which is being used widely to reduce and control the oxides of nitrogen (NO_x) emission from diesel engines. EGR controls the NO_x because it lowers oxygen concentration and flame temperature of the working fluid in the combustion chamber. However, the use of EGR leads to a trade-off in terms of soot emissions. Higher soot generated by EGR leads to long-term usage problems inside the engines such as higher carbon deposits, lubricating oil degradation and enhanced engine wear. Present experimental study has been carried out to investigate the effect of EGR on soot deposits, and wear of vital engine parts, especially piston rings, apart from performance and emissions in a two cylinder, air cooled, constant speed direct injection diesel engine, which is typically used in agricultural farm machinery and decentralized captive power generation. Such engines are normally not operated with EGR. The experiments were carried out to experimentally evaluate the performance and emissions for different EGR rates of the engine. Emissions of hydrocarbons (HC), NO_x, carbon monoxide (CO), exhaust gas temperature, and smoke opacity of the exhaust gas etc. were measured. Performance parameters such as thermal efficiency, brake specific fuel consumption (BSFC) were calculated. Reduction in NO_x and exhaust gas temperature were observed but emissions of particulate matter (PM), HC, and CO were found to have increased with usage of EGR. The engine was operated for 96 h in normal running conditions and the deposits on vital engine parts were assessed. The engine was again operated for 96 h with EGR and similar observations were recorded. Higher carbon deposits were observed on the engine parts operating with EGR. Higher wear of piston rings was also observed for engine operated with EGR.     

Effect of exhaust gas recirculation on diesel engine nitrogen oxide reduction operating with jojoba methyl ester

Jojoba methyl ester (JME) has been used as a renewable fuel in numerous studies evaluating its potential use in diesel engines. These studies showed that this fuel is good gas oil substitute but an increase in the nitrogenous oxides emissions was observed at all operating conditions. The aim of this study mainly was to quantify the efficiency of exhaust gas recirculation (EGR) when using JME fuel in a fully instrumented, two-cylinder, naturally aspirated, four-stroke direct injection diesel engine. The tests were carried out in three sections. Firstly, the measured performance and exhaust emissions of the diesel engine operating with diesel fuel and JME at various speeds under full load are determined and compared. Secondly, tests were performed at constant speed with two loads to investigate the EGR effect on engine performance and exhaust emissions including nitrogenous oxides (NO_x), carbon monoxide (CO), unburned hydrocarbons (HC) and exhaust gas temperatures. Thirdly, the effect of cooled EGR with high ratio at full load on engine performance and emissions was examined. The results showed that EGR is an effective technique for reducing NO_x emissions with JME fuel especially in light-duty diesel engines. With the application of the EGR method, the CO and HC concentration in the engine-out emissions increased. For all operating conditions, a better trade-off between HC, CO and NO_x emissions can be attained within a limited EGR rate of 5–15% with very little economy penalty.     

Use of HOT EGR for NOx control in a compression ignition engine fuelled with bio-diesel from Jatropha oil

Environmental degradation and depleting oil reserves are matters of great concern round the globe. Developing countries like India depend heavily on oil import. Diesel being the main transport fuel in India, finding a suitable alternative to diesel is an urgent need. Jatropha based bio-diesel (JBD) is a non-edible, renewable fuel suitable for diesel engines and is receiving increasing attention in India because of its potential to generate large-scale employment and relatively low environmental degradation. Diesel engines running on JBD are found to emit higher oxides of nitrogen, NO_x. HOT EGR, a low cost technique of exhaust gas recirculation, is effectively used in this work to overcome this environmental penalty. Practical problems faced while using a COOLED EGR system are avoided with HOT EGR. Results indicated higher nitric oxide (NO) emissions when a single cylinder diesel engine was fuelled with JBD, without EGR. NO emissions were reduced when the engine was operated under HOT EGR levels of 5–25%. However, EGR level was optimized as 15% based on adequate reduction in NO emissions, minimum possible smoke, CO, HC emissions and reasonable brake thermal efficiency. Smoke emissions of JBD in the higher load region were lower than diesel, irrespective of the EGR levels. However, smoke emission was higher in the lower load region. CO and HC emissions were found to be lower for JBD irrespective of EGR levels. Combustion parameters were found to be comparable for both fuels.     

The influence of Exhaust Gas Recirculation (EGR) on combustion and emissions of n-heptane/natural gas fueled Homogeneous Charge Compression Ignition (HCCI) engines

In Homogeneous Charge Compression Ignition (HCCI) combustion, a lean premixed charge combusts simultaneously in multiple sites. Utilizing highly diluted mixtures, and lack of any significant flame propagation, in-cylinder NO_x formation is reduced. Making HCCI engine a feasible alternative to conventional engines requires several challenges to be resolved. Combustion timing control is one of the most important of these items. It should be done in order that heat is released at the most optimum phasing for efficiency and emissions. In this study, a Waukesha Cooperative Fuel Research (CFR) single cylinder research engine was used to be operated in HCCI combustion mode fueled by natural gas and n-heptane. The main goal of the experiments was to investigate the possibility of controlling combustion phasing and combustion duration using various Exhaust Gas Recirculation (EGR) fractions. For the analysis of the results, a modified apparent heat release model was developed. The influence of EGR on emissions was discussed. Results indicate that applying EGR reduces mean charge temperature and has profound effect on combustion phasing, leading to a retarded Start of Combustion (SOC) and prolonged burn duration. Heat transfer rate decreases with EGR addition. Under examined condition EGR addition improved fuel economy, reduced NO_x emissions and increased HC and CO emissions.